Search Documents

By Nancy Estrada, Jane Nowell, Cathy Jennings, Debra Yniguez, Carol Lavery, Kristin Harrer

Pilots of the MH-60S helicopter are exposed to continuous whole body vibration (WBV). Pilot fatigue is a growing operational concern due to the increased frequency of extended durations of missions (6-8+hours) in support of Operations Iraqi Freedom and Enduring Freedom. Endurance aspects of the currently used rotary wing seating systems were not optimized for the longer missions and wide range of pilot anthropometric measurements, which is now typical of naval aviation. The current seating systems were designed primarily to meet crashworthiness requirements, not for the wide range of pilot anthropometry or to mitigate WBV. Albeit, an issue, pilot fatigue and reduced mission effectiveness are also critical concerns. Current Hazard Reports indicated that pain in pilots’ legs and backs begin two to four hours into the flight and increase with time. Mission readiness also decreases with an increase in flight duration due to the constant distraction of pilots shifting in their seats while trying to get comfortable. Froom, et al [2] reported a dose-response relationship between the length of military helicopter flights and back discomfort. He also concluded that this pain is typically dull, over the lower back, and its prevalence and intensity are dependent on the total flight hours of exposure. Methods This study evaluated WBV produced in the pilot seating systems onboard the MH-60S. The purpose of the study was to test and compare the effectiveness of two different seat cushions, the current seat cushion versus an anti-vibration seat cushion. Both seat cushions were measured for acceleration levels averaged over five-minute intervals using a triaxial seat pad accelerometer. The recordings were completed for a 3-hour straight and level flight. A frequency analysis from 0-80 hertz (Hz) was conducted on all acceleration measurements to determine the dominant axis and frequency of the pilots’ vibration exposure. The results were then compared to the applicable Threshold Limit Values (TLVs) established by the American Conference of Governmental Industrial Hygienists (ACGIH) [1] and the International Organization for Standardization (ISO) 2631.1 [3] to determine the MH-60S pilots’ permissible exposure time for both seat cushions. Results The results of the study showed that for both seat cushions the vibration levels of the z-axis at 16 Hz had the shortest allowable exposure duration, according to the ACGIH TLVs. In the z-axis at 16 Hz, the MH-60S’s current seat cushion’s acceleration levels indicated an exposure time limit of approximately 6 hours, while the anti-vibration seat cushion’s acceleration levels pierced the 8-hour exposure time limit curve. This is shown in the graph below.

Jan 6, 2006

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1980 was $328.6 million, a decrease of $7.8 million from 1979. Cement, crushed stone, lime, clays, and sand and gravel continued as the major commodities produced. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in native asphalt, ferroalloys, kaolin, and oyster shell; fourth in dimension marble, masonry cement, and bentonite; and fifth in fire clay and lime. Alabama ranked in the top 20 States in total value of non-metallic minerals produced. Adverse economic conditions in the construction and metals industries impacted on the minerals industry in Alabama. Mineral producers supplying raw or finished materials to these industries experienced periodic reductions in sales during the year. Unit price increases did not keep up with inflation.

Jan 1, 1982

By Jr. Boyle

This report analyzes the availability of chromium in the form of ferroalloy products (high-carbon and low-carbon ferrochromium and ferrochromium-silicon) and chromite products (metallurgical, chemical, refractory, and foundry sands) in market economy countries (MEC's). A total of 873.5 Mmt of in situ material, containing 202.5 Mmt of chromium, in 10 MEC countries was analyzed for availability as of the January 1989 study date. Extraction and beneficiation of this in situ material would result in 475.4 Mmt of marketable chromite products. As analyzed, 288.5 Mmt of these chromite products would be available for export or for internal chemical and refractory use and 186.9 Mmt would be smelted in-country to produce 74.3 Mmt of high-carbon ferrochromium, 3.9 Mmt of low-carbon ferrochromium, and 2.0 Mmt of ferrochromium-silicon, all available for export. A network flow model, which includes centrally planned economy countries (CPEC's), was also constructed to analyze world chromium supply and demand interactions for the period 1986 through 1994 and to address a hypothetical North American embargo on direct imports of all South African chromium products beginning in mid-1990. The model shows capacity constraints developing in the MEC high-carbon ferro chromium industry in 1987 and a possible subsequent overreaction by the industry in terms of new capacity additions. The results suggest that sufficient chromium is available to North America should an embargo on direct imports from South Africa be imposed by its governments. However, the effect on export revenues in South Africa is relatively small, and timely increases to world ferrochromium, chemical chromite, and foundry sand chromite capacities would be required.

Jan 1, 1993

By Daryl R. Tweeton

This Bureau of Mines publication provides information to assist in selecting a lixiviant (leach solution) for in situ uranium leaching. The cost, advantages, and disadvantages of lixiviants currently used and proposed are presented. Laboratory and field tests are described, and applications of geochemical models are discussed. Environmental, economic, and technical factors should all be considered. Satisfying environmental regulations on restoring groundwater quality is becoming an overriding factor, favoring sodium bicarbonate or dissolved carbon dioxide over ammonium carbonate. The cheapest lixiviant is dissolved carbon dioxide, but it is not effective in all deposits. Technical factors include clay swelling by sodium, acid consumption by calcite, and the low solubility of oxygen in shallow deposits. Laboratory leaching tests can provide useful data. However, they can be misleading if, for example, the ore is allowed to oxidize before testing or if distilled water instead of formation water is used for making solutions for permeability tests. Geochemical models presently are more useful for indicating trends in solubility than in reliably predicting concentrations.

Jan 1, 1981

By Fred N. Kissell

In This Chapter [Measuring the gas emission from the coal Methane at the top of the silo Methane at the load-out area and Actions taken after a silo explosion] Methane accumulations in coal silos have resulted in the occasional silo explosion. These can be quite violent and dangerous because coal dust adds to the strength of the blast. However, with the appropriate precautionary measures, methane accumulations in silos can be greatly reduced. Mine Safety and Health Administration (MSHA) regulations at 30 CFR2 77.201 require that the methane content in the air of any coal silo be maintained below 1.0 vol %.3 Also, MSHA requires that methane tests be conducted before any electrical equipment is energized, unless a continuous monitor capable of deenergizing the electrical equipment is used.4 Measuring the gas emission from the coal. The first necessary step in dealing with silo methane issues is to measure the gas emission from the coal going into the silo. Such measure-ments allow one to estimate the silo ventilation needs and permit a comparison with the methane controls used at other mines that have similar gas levels. The gassiness of the coal can be measured by taking conveyor belt grab samples.5 Matta et al. [1978] measured the gas emission from conveyor belt grab samples using a simple desorption test. To conduct the test, they collected several grab samples of coal, weighing a few pounds each, from the conveyor belt entering the silo.6 They then sealed the coal into an airtight sample container that was equipped with a valve and short hose along with a pressure gauge. Every few hours they opened the valve and bled the emitted gas into a water-filled graduated cylinder that had been inverted and placed in a pan of water (Figure 11–1). The results are shown in Figure 11–2.

Jan 6, 2006

The Bureau of Mines is the engineering arm of the Government for mineral resources. Its mission is to carry out laboratory and field studies that will assure the wise and effective development and use of our Nation's minerals, fuels, and underground domain in order to preserve the security and enhance the welfare of our people. Specifically, studies are directed to the means by which current and emerging demands may be met, the real cost of such achievements, and the assessment of related social and economic factors. Ways are sought to fulfill our material needs in a manner that minimizes occupational hazards to workers in the industry, reduces waste, and ensures that mineral raw materials are supplied and mineral-based products are used and are disposed of efficiently, without objectionable social and environmental costs. The headquarters of the Bureau of Mines is located in Washington, D.C. The Bureau's research and development program, however, is conducted at 19 research centers and laboratories located throughout the United States.

Jan 1, 1971

By Roy L. Soderberg

The Bureau of Mines has conducted substantial research on the design, construction, and operation of metal and nonmetal tailings ponds. This design guide, like related Bureau publications that preceded it, is produced to assist the industry in the management of mill tailings disposal. It covers the site selection, sampling, laboratory testing, design, construction, operation, and inspection of tailings embankments. The effects of environment, topography, and hydrogeology are also included, and various methods of stability analysis and factors affecting stability are reviewed. Because of the diversity of problems encountered in tailings embankments, specific solutions are not intended. The guide is, however, a useful checklist for designers, operators, and inspectors of this type of structure.

Jan 1, 1977

Objective: To identify and evaluate a permanent stopping to direct ventilation airflows in large-opening metal/nonmetal mines.

May 1, 2006

This study assesses whether Narragansett Basin coal deposits could be developed commercially in the near future. To do this, we identify the potential market for the coal, assess the price these users would be willing to pay for Narragansett coal, and this price to the expected costs of producing Narragansett coal. The study concludes that the major market, New England utilities, could burn bituminous coal from Pennsylvania or West Virginia at a lower total cost than Narragansett Basin coal, assuming expected mining conditions and emission policies. Therefore, the study concludes that Narragansett Basin coal resources could not be developed economically in the next ten years.

Jan 1, 1979

By R. P. Maloney

The economic viability of four depleted mines near Kennicott, Alaska, was determined by the Bureau of Mines to assess their profitability if they were developed today and thus estimate cost data for a medium-sized mine, mill, and town complex. This information should help the State and Federal Governments appraise the potential development of similar-sized mining operations in Alaska. Modern conventional mining and milling techniques were assumed, and I capital and operating costs were derived using flowsheets and standard costing methods. A total capital investment of $37.6 million was necessary to install a 1,000-ton-per-day shrinkage stope mine, flotation-type mill, and support facilities; capital requirements were divided about evenly among the three components. Operating costs, including labor, supplies, power, water, and ' indirect and fixed costs, totaled $42.79 per ton of ore; the mining accounted for nearly one-half the cost. To obtain a 12-percent discounted cash flow rate of return on investment, the analysis showed that the ore could be mined and milled, and the concentrate could be trucked via public roads to a dock facility in Valdez, Alaska, barged to Tacoma, Wash., and smelted and refined for 34.7 cents per pound for copper and 104.0 cents per ounce for silver. The average May 1972 price was 52.6 cents for copper and 158.3 cents for silver. The same set of data was used to examine the economic viability of the mine with the cost of constructing a private road from McCarthy, Alaska, To Valdez, Alaska. The 148-mile road added $53.3 million to the original capital costs and raised the required price of copper to 57.4 cents per pound and the required price of silver to 172.0 cents per ounce. The additional coat of building, maintaining, and paying taxes on a private road from McCarthy, Alaska, to Valdez, Alaska, would make this venture uneconomical.

Jan 1, 1973

By M. A. Elliott

Diesel-powered haulage equipment has recently been tested and approved for permissibility by the Bureau of Mines for use in mining in the United States. Achievement of this advance in safety involved extensive studies, both in the testing station (2, 3, 20, 21, 22, 23, 24, 25, 26, 27)3/ and in the field 1, 4, 13, 30), of the operating characteristics of diesel engines in relation to the toe of such engines underground. The results of these studies formed the basis for establishing the requirements that should be met by diesel-powered haulage equipment approved for permissibility. Considerable interest has been manifested in the development of diesel-powered haulage equipment fur mines. The purpose of this paper is to retrace briefly the course of this development and to answer such questions as: What is the history of the use of diesel engines underground? Why has the Bureau of Mines been interested in the development of diesel-powered haulage equipment for use in mines?

Jan 1, 1953

By H. A. Thorne

This paper describing the mining practices at the Chino mines at Santa Rita, Grant County, N. Mex., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Nevada Consolidated Copper Co., Chino mine's, operates an open-cut copper mine at Santa Rita, Central mining district, Grant County, N. Mex. This mine is located about 16 miles east and slightly north of Silver City, the county seat. The ore is-transported in standard railroad cars by the Atchison, Topeka & Santa Fe Railway Co., approximately 10 miles to Hurley where it is milled. The concentrated are shipped approximately l'70 miles over the same railroad to the smelter of the American Smelting and Refining Co., at El Paso, Tex. (fig. 1)

Jan 1, 1931

By Marvin L. Whisman

This report describes the preparation of tritium-labeled organic compounds to be used by the Federal Bureau of Mines in studying the role of certain gasoline constituents in gum-forming mechanisms. The gasoline constituents that have been investigated boil within a range of approximately 90 to 230° C. and can be classified as paraffins. naphthenes, olefins, diolefins, monocyclic aromatics, polycyclic aromatics, and organic sulfur, nitrogen,: and oxygen compounds. The technique of Wilzbach has been applied to more than 50 samples. Purification techniques have been developed that accomplish rapid and effective purification as well as removal of labile tritium in a one-step operation. Data are presented to show the rate of exchange between tritium and hydrogen that can be expected for a variety of compounds common to a full-boiling-range gasoline. These values should be useful to other investigators using tracer programs involving tritium labeled compounds.

Jan 1, 1961

By A. J. Farstad

Electromagnetic location tests were conducted by Westinghouse Georesearch Laboratory under the sponsorship of the U. S. Bureau of Mines at the Galena Mine in Northwest Idaho. The objectives of these tests were to evaluate the performance in deep hardrock mines of an electromagnetic location system previously developed for the U. S. Bureau of Mines for use in coal mines. Tests were performed using long wire transmitting antennas as well as horizontal and vertical transmitting loops at depths from 3000 feet to 4300 feet (995 metres to 1311 metres). Surface measurements were made of magnetic field strengths, field strength patterns, and background noise, These measurements were compared with theoretical predictions for a homogeneous ground conductivity consistent with this particular geologic region. The results of the Galena Mine tests show conclusively that light-weight portable electromagnetic transmitters can be effectively utilized to provide uplink communications and location information in deep hardrock mines. Typical metal mines such as Galena utilize deep vertical shafts for mine access and haulage and these shafts produce signal enhancement at the surface from underground electromagnetic transmitters by as much as 30 dB. The results also show that horizontal wire configuration can serve as an effective alternative to the magnetic dipole antenna as a rescue transmitting antennaa and can be used when the required area is not available for deployment of a loop antenna. In spite of the electromagnetic coupling effects observed in the vicinity of the shafts, the location accuracy obtained still provided useful information on the general location of the transmitting sources involved. The horizontal wire location accuracy was within 46 metres, while the vertical magnetic dipole and the horizontal magnetic dipole accuracies were within 152 metres and 110 metres respectively at a 915 metre depth.

Jan 1, 1973

By W. A. Cole

This report covers the preliminary phase of an investigation of some clays and shales and other materials in North and South Dakota to determine the feasibility of lightweight -aggregate manufacture in the two States. The background of the light - weight -aggregate industry, on a national basis, and results of preliminary laboratory testing of samples of North and South Dakota clays and shales from various localities are presented herein. The countrywide search for lightweight aggregates was necessitated toward the end of the 19th century by the change in building design from thick, heavy, load- bearing walls to a framework of structural steel .beams and columns with thin walls, followed shortly by the use of reinforced concrete and structural concrete as materials for the load-supporting frame. Ordinary concrete, with sand and gravel aggregate, weighs about 150 pounds to the cubic foot. A lighter concrete was needed to relieve the dead load and make it possible to construct higher buildings or add stories to existing buildings.

Jan 1, 1954

Late in 1974 at a meeting with the Cedar Coal Company in Chelyan, West Virginia, a very definite requirement for an automatic heat sensing fire suppression system for the type coal augers used in their mine was revealed. Several fires had been experienced, and while equipment loss was a consideration, operator safety was also a concern. As of that date no one had developed an automatic system specifically for fire suppression on coal augers. II. EQUIPMENT DEVELOPMENT As a result of the above meeting, an unsolicited proposal was made to the Bureau on March 1, 1975, and a contract was issued to provide the following services: A. Determine and define fire hazard problem on Compton Coal Auger. B. Modify or otherwise mike a Lease "AFEX" system suitable for protecting the fire hazard area developed in paragraph "A". C. Make installation of "AFEX" system. D. Monitor installation for reliability for a period of 90 days after installation. C. ConJurt a simulated fire test to determine effectiveness on system.

Jan 1, 1975

By NEFE AEWFW

Changes in the 1980 quantity and value of the sales of various natural abrasives, compared with the data for 1979, were of a mixed nature. Output of garnet and special silica stone products increased in both tonnage and value during the year, while emery and tripoli-type materials production decreased in both tonnage and value. The reported quantity and value of sales of manufactured abrasive material-fused alumina and alumina-zirconia, silicon car-bidet and metallic iron and steel shot and grit-also decreased for 1980. [ ]

Jan 1, 1981

By J. C. Gerdeen

A new analytical model for the shear stiffness at a joint of the fully-grouted resin roofbolt is developed using the Theory of Elasticity and an analogy to a beam on an elastic foundation, Gerdeen [2]. The model developed in this study treats the elastic foundation modulus of the resin as being composed of both an elastic rock and an elastic resin. All previous attempts have neglected the elasticity of the rock and treated only the resin. A three dimensional finite element model of the bolt-resin-rock system is developed also and comparisons are made between the predictions made by it and the analytical solution. It is found that the agreement between the two representations ranges between 1.2% and 10.5%, with the greater differences being observed for systems of very large or very small bolt diameters and resin annulus thicknesses. Since such configurations are not the rule in practice parameter studies are performed using the analytical solution with the finite element solution being used as a check. For a 0.75 in. bolt, a resin annulus thickness of 0.1375 in., a resin with E = 7 x 105 psi and -1) = 0.210, and a rock of modulus E = 6.8 x 106 psi and V = 0.159 the shear stiffness is found to be 1.220 x 106 lb,/in, from the analytical solution and 1.245 x 106 lb,/in, from the finite element model. Applying the finite element model to the problem of the axial stiffness of the fully-grouted resin roofbolt a value of 6.002 x 106 lb./in. is obtained which proves to be at least 50% higher than any of the now existing analytical predictions.

Jan 1, 1976

Coal research and technologic work by the Bureau of Mines covers a broad program of investigation aimed at conservation and utilization of this important natural resource. Conservation is served by a constant search for higher efficiencies in mining, preparation, and use. Increased utilization is sought through various projects that probe new ways to use coal and expand existing coal markets. This report, the twenty-eighth in the series,3 gives the highlights of Bureau of Mines coal research and technologic work in 1963. The scope and complexity of the program makes it virtually impossible to report all progress on every project, even tor a 12-month period. Full insight into each project can be gained only through intensive review of basic objectives, past accomplishments, and current status of the work. Details of the work are given in numerous publications issued by the Bureau and its laboratories and centers located throughout the country.

Jan 1, 1964

Coal research and technologic work by the Bureau of Mines covers a broad program of investigation aimed at conservation and utilization of this important natural resource. Conservation is served by a constant search for higher efficiencies in mining, preparation, and use. Increased utilization is sought through various projects that probe new ways to use coal and expand existing coal markets. This report, the twenty-eighth in the series,3 gives the highlights of Bureau of Mines coal research and technologic work in 1963. The scope and complexity of the program makes it virtually impossible to report all progress on every project, even tor a 12-month period. Full insight into each project can be gained only through intensive review of basic objectives, past accomplishments, and current status of the work. Details of the work are given in numerous publications issued by the Bureau and its laboratories and centers located throughout the country.

Jan 1, 1964