Search Documents

Ohio has an estimated 46 billion tons of coal beneath 12,000 square miles of the eastern third of the state. Recoverable coal reserves within this vast area are estimated at 21 billion tons, 3.2 billion tons of which have been mined since 1800. Ohio is the eleventh-largest coal- producing state in the nation and ranks third nationally in coal consumption. Coal resources in Ohio lie in as many as 60 identifiable coal seams along the northwestern flank of the Appalachian coal basin. Except where interrupted by minor faults and erosional discontinuities, these rocks dip gently and uniformly to the east, simplifying the mining methods needed to extract the coal. Fourteen of Ohio's 60 coal seams are considered to be important, although only a small number of seams are currently being mined. Ohio first enacted a surface coal mining law in 1948, requiring in part a $100 per acre reclamation bond. Ohio progressively strengthened its surface mining law in 1949, 1955, 1959, 1961, 1965,1972,1975,1978, and 1981. At the time of its enactment, Ohio's 1972 mining law was one of the most stringent in the country. This law also created a state coal severance tax of four cents per ton to be used for abandoned mine land reclamation. Ohio received primacy to regulate the surface coal mining operations within the state August 16,1982. Its Abandoned Mine Land Program was approved on the same date.

Jan 1, 1992

By J. S. Kennedy, M. M. Fine

"INTRODUCTION Barite is one of the major industrial minerals whose production has increased considerably in the last 10 years. In 1935 domestic production of barite was 218,075 tons and. had increased by 1944 to 515,136 tons. 3/ Most of the primary uses for barite and barite products were developed before 1935, so the increase in barite production reflects the growth of industry in general rather than any recent developments in barite technology.The principal uses for ground and crushed barrite are as a weighting agent in heavy drilling fluids, as a filler in rubber and other materials, as a pigment and extender in paints, and as a flux in glass melt. In addition, a considerable' quantity of barite serves as the raw material for the manufacture of lithopone and barium chemicals.Specifications for barrite vary widely and depend primarily on the use to which the material is put. The primary requisites for barite used in heavy drilling muds -are that it have a minimum specific gravity of 4.2 and be very,low in soluble salts. A minimun barium sulfate content of 92 percent may be specified; but this is less important than the gravity. 4/ In addition before consumption the material must be ground to '92 percent minus 325-mesh. 5/ Lithopone and chemical manufacturers require a minimum of 94 Percent barium sulfate, a maximum of 1.0 percent iron oxide, and not more than a trace of fluorine. 6/ Barite used as fillers in light-colored products should be of fairly high grade, but the filler used in dark products may be considerably lower grade.Glass barite should contain a minimum of 96 percent barium sulfate, not more than 3 percent moisture, a maxium of 0.2 to 0.4 percent iron oxide, and not more than a trace of titanium oxide. Particle size is a matter of some importance in glass barite, also. 7/"

May 1, 1948

By Lewis M. McNay

The Bureau of Mines located and examined 292 burning coal refuse banks throughout the Nation's coal-producing regions in 1968. These coal waste fires, extending over 3,200 acres, produce poisonous, acrid gases and particulate matter that pose a threat to health and safety in the surrounding areas, damage vegetation, and cause the deterioration of nearby structures and buildings. Methods of extinguishing coal refuse fires are discussed, and an approach to eliminating future occurrences of these fires is presented.

Jan 1, 1971

Isometric strength is defined as the capacity to produce force or torque with a voluntary isometric (muscle[s] maintain[s] a constant length) contraction. The key thing to understand about this type of contraction and strength measurement is that no body movement occurs during the measurement period. The tested person's body angles and posture remain the same throughout the test. Isometric strength has historically been the type most studied and measured. It is probably the easiest to measure and to understand. Some strength researchers feel that isometric strength data may be difficult to apply to some "real life" situations because in most real circumstances people are moving - they are not static. Other researchers counter that it is equally difficult to determine the speed of movement of a person or group of persons doing a job (each moves in his or her unique manner and speed across the links and joints of the body). Thus, dynamic strength test data collected on persons moving at a different speed and/or in a different posture from the "real world" condition will be just as hard to apply. In truth, neither is better - they are different measurements. Both researchers and users should collect and use data that they understand and that fits their application. Workplace Assessment When a worker is called on to perform a physically demanding lifting task, the external load produces moments - tendencies to produce motion, also called torques - about various joints of the body.(1) Often these moments are augmented by the force of gravity acting on the mass of various body segments. For example, in a biceps curl exercise, the moment produced by the forearm flexors must counteract the moment of the weight held in the hands as well as the moment caused by gravity acting on the forearm's center of mass. To perform the task successfully, the muscles responsible for moving the joint must develop a greater moment than the combined moments of the external load and body segment. It should be clear that, at each joint of the body, there is a limit to the strength that the muscle can produce to move ever-increasing external loads. This concept forms the basis of isometric muscle strength prediction modeling.(1) The following procedures are generally used with this biomechanical analysis technique. First, workers are observed (and usually photographed or video-taped) as they perform physically demanding tasks. For each task the posture of the torso and the extremities are documented at the time of peak exertion. The postures are then re-created using a computerized software package, which calculates the load moments produced at various joints of the body as the task is performed. The values obtained during this analysis are then compared to population norms for isometric strength obtained from a population of industrial workers. In this manner, the model estimates the proportion of the population

Jan 1, 1998

By George S. Rice

In 1911 the Director of the United States Bureau of Mines instructed the chief mining engineer of the bureau , during an investigation of coal-mine safety conditions in Europe, to ask the directors of the various mine-experiment stations whether they would favor a European conference . The majority of the officials in immediate charge of experiment stations favored the plan , and Victor Watteyne, inspector general of Belgium, suggested that the United States call such a conference to be held immediately after the Eighth International Congress of Applied Chemistry, which was to assemble in New York on September 3, 1912 . Accordingly, invitations were issued by the United States Government to those countries having mine-experiment stations , namely, Austria-Hungary, Belgium, France, Germany , and Great Britain, and to those that contemplated the establishment of such stations , Canada and Mexico . All but Great Britain and Canada accepted ; Mexico designated a representative , who later found it impossible to come. The Government of Great Britain in declining, expressed regret at its inability to accept ; an informal statement was made that the opening of the experimental gallery at Eskmeals , England , occupied the attention of the officials in charge . Delegates were appointed by their respective Governments as follows: Austria-Hungary, Julian Czaplinski , royal mining engineer. Belgium, Victor Watteyne , inspector general of mines . France, J. Taffanel, director of the Lievin experiment station . Germany, Carl Beyling, bergassessor, director of Dortmund experiment station. United States , Charles E. Munroe, consulting explosives expert and George S. Rice, chief mining engineer of the Bureau of Mines . Subsequently Mr. William O'Connor , a mining engineer and mine operator of Wales , who opportunely appeared at the Pittsburgh station with letters of introduction from the South Wales Institute of Engineers and from prominent mining officials of Great Britain , was unanimously invited to take part in the meeting as an unofficial representative of Great Britain . Messrs . Beyling, Taffanel , and Watteyne were met in New York on September 3, by George S. Rice, who accompanied them to Washington, where they were welcomed by Director J. A. Holmes , of the Bureau of Mines , and where , with the delegates to the Eighth International Congress of Applied Chemistry , they were presented to President Taft . Mr. Taffanel was unfortunately called back to France just before the scheduled time of the conference on account of a mine disaster ; the other delegates , including Mr. Czaplinski , convened at Pittsburgh on the morning of September 14. Mr. Rice, representing the Director of the Bureau of Mines , acted as temporary chairman , and called the meeting to order.

Jan 1, 1914

By B. J. Dalton

The Bureau of Mines Helium Activity has developed a computer program for use in the reduction of pressure-volume-temperature (PVT) data obtained with a Burnett compressibility apparatus. This program includes important modifications and extensions of some of the methods currently used for treating these types of data and yields statistical information that cannot be obtained from any other published work. The methods of calculation make use of a general nonlinear least-squares technique developed at the Helium Research Center. Because of a need to investigate different functional forms for representing the compressibility factor isotherm, 2, the computer program has been written in such a way that the only additional coding required is the so-called compressibility function subroutine. This subroutine defines the analytical form of Z and certain of its partial derivatives. The program described herein is believed to be the most advantageous for use in treating isothermal Burnett compressibility data.

Jan 1, 1970

By Martin D. Conyac

A mineral resource survey of rock types and geologic structures indicates that the Mt. Henry RARE II area has low potential for the discovery of metallic minerals. Potential for coal and geothermal resources is negligible. Essentially, the Mt. Henry RARE II area has had no claim-staking activity, nor has any mine been developed in it. SETTING Size and Location The 23,000-acre (9,308 ha) "1t. Henry RARE II area (No. 1-666) lies within the Kootenai National Forest approximately 36 mi (58 km) north of Libby, Montana, in the Purcell Mountain; of Lincoln County. Irregularly shaped, the area measures roughly 5-1/2 mi (8.9 km) north-south by 8 mi (12.9 km) Past-west, and lies about 1-1/2 mi (7.2 km) south of the Canadian border.

Jan 1, 1982

By N. Kumar Kittusamy

The purpose of this study was to assess the adequacy of the cab design and to determine the percentage of musculoskeletal symptoms among workers. A questionnaire was designed to assess demographics, work information, job history, and musculoskeletal symptoms in operators of heavy construction equipment. Information concerning equipment included design of the seat/chair, levers, pedals, bothersome vibration, quality of egress from the equipment, proper preventative maintenance and repairs, and age of the equipment. The body regions that were evaluated included the neck, middle/upper back, low-back, shoulder/upper-arm, elbow/forearm, wrist/hand, hip, knee, and ankle/foot. One hundred and eighty nine operators completed the questionnaire. The results indicate that these workers are at risk for developing musculoskeletal disorders, the need to perform a larger survey to further substantiate the outcome, and the need to quantify risk factors (i.e., whole-body vibration and static sitting postures).

Jan 1, 2003

By Jacqueline V. Rich

The relationship between surface and ground water quality and copper mining in the Globe-Miami area is investigated in this three-year study. Methods to prevent, minimize, mitigate, or treat polluted waters are identified and evaluated. Best Management Practices are incorporated in a recommended plan to manage the area's water quality.

Jan 1, 1983

By Jos. R. Guiteras

This is one of a series of information circulars describing mining and milling methods being published by the Bureau of Mines. The Summitville Consolidated Mines, Inc., is the only company now active at Summitville. Since the holdings of the company include those of most of the former producers of the camp, the paper virtually becomes a description of the Summitville district. The field data were collected from August 23 to 28, 1937. ACKNOWLEDGMENTS The writer gratefully acknowledges his indebtedness to H. F. Detrick, president, and Edward Thornton, general manager of the company for their cooperation in making this paper possible. Most of the information on underground operations was given by Roy Jellison, mine superintendent; the metallurgical data were supplied by Art Carl son, metallurgist, and W. L. Anderson, mill superintendent; much general and technical information was supplied by J. H. Hannan, engineer.

Jan 1, 1938

By Eric R. Bauer

This Bureau of Mines manual is intended to provide a better understanding of ground movement and the technology available for measuring it, The manual deals with convergence, strata separation, lateral roof movement, stress, and support load in underground mines. The instruments that measure these ground control parameters are described in detail. Step-by-step procedures for selecting the appropriate instrument are presented, which consider such factors as approximate cost, installation procedures, data collection, and data interpretation; and an instrument selection worksheet is provided to facilitate the instrument selection process. Actual instrument case studies and a list of instrument suppliers are presented in the appendixes.

Jan 1, 1985

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. Downstream processing of these mineral fuels to petrochemicals and fertilizers is a major investment opportunity. In 1991, the 15 countries that constituted the region accounted for 26 % of world crude petroleum output, 15.3 % of world natural gas plant liquid production, and 4.5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. Production of these mineral fuels all declined from that of 1990 owing to the Persian Gulf War, during which output from Kuwait and Iraq either ceased owing to war damage, or was embargoed. Prior to the war, Iraq and Kuwait were the fourth and fifth largest world producers of crude petroleum, respectively. In the war, virtually all of Kuwait's production and transport facilities were destroyed or damaged. Iraq's output was embargoed from export, with only domestic sales taking place. The embargo also affected Jordan, both in terms of transshipment of materials through it to Iraq and in exports of phosphate and potash. Shipments of crude petroleum by pipeline from Iraq through Saudi Arabia and Turkey and by vessel through the Persian Gulf were terminated. However, the loss in production from Iraq and Kuwait was made up by accelerated output from other Middle East and world producers. Saudi Arabia, in particular, with its excess production capacity, accounted for the largest portion, increasing crude petroleum output by 27 % to almost 3 billion barrels.

Jan 1, 1993

By Magnus Persson

ISO8662-4, “Hand-held portable power tools - Measurement of vibrations at the handle - Part 4: Grinders” is under revision. The new revision shall harmonize ISO 20643 “Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission” which, among others, requires measurements in three directions and declared values related to the upper quartile of real-use vibration. To get the most suitable test method, a round robin test was made for evaluation of the two test methods proposed by the ad-hoc group working with this standard revision. Methods Seven laboratories measured the vibration from four grinders of different sizes, with and without autobalancing units. The laboratories come from universities, health & safety laboratories and grinder manufacturers. Two measurement methods are evaluated with respect to repeatability and reproducibility: 1. Grinding on a well-defined mild steel bar with depressed center wheels according to detailed test instructions. The test sequence starts and ends with 10 seconds of running the grinder in the air, when measuring the unbalance contribution to the vibration coming from the unbalance of the grinding wheel. Between these runs the average vibration during 60 seconds of grinding is measured. Three operators do five grinding tests per grinder. 2. Measurements using an aluminum unbalance disc similar to the one defined in ISO8662-4. Each operator runs the grinder four times, between each run the unbalance is moved 180 degrees to avoid variations caused by the play between the test wheel and the spindle. The averaging time is 10 seconds. Each grinder is tested by three operators. Repeatability is the spread within a lab between operators and over short time period for one machine and reproducibility is the spread between laboratories and over longer time periods for one machine. Instrumentation and transducer location are chosen according to ISO8662-4 and circulated test instructions. Results Both the repeatability and reproducibility is poor for the real grinding test, see figure 1. The coefficient of variation for repeatability is approximately 40% higher for the grinding test and the coefficient of reproducibility is 60% higher for the grinding test than for the unbalance disc test.

Jan 6, 2006

By Ira L. Wright

This paper describing the milling practice of the Black Hawk Consolidated Mines Co., is one of a series being prepared by the United States Bureau of Mines. ACKNOWLEDGMENTS Part of the information contained in this paper was furnished by I. H. Stanley, mill superintendent, Black Hawk Consolidated Mines Co., Hanover, M. M., and a part by the South-western Engineering Corporation, Los Angeles, Calif. The assistance of T. G. Chapman in arranging the paper for publication is also acknowledged.

Jan 1, 1930

By Eugene H. Skinner

The U.S. Bureau of Mines conducted experiments on the use of lightweight concrete in the density range of 100 Ib/ft3 for liners in underground mines. Three test sections were completed: a monolithic, portal-type structure with integral walls and arch constructed aboveground; an underground test section constructed in a mine drift using plywood forms; and a second section constructed in a drift using an air-supported formwork. The lightweight concrete in the two underground test sections was placed using piston pumps and a slickline. Fiber reinforcement was added to the concrete in the mine sections without any apparent problems with either pumping or placement of the concrete. In another experiment, the Bureau and Hecla Mining Co., Mullan, rD, used lightweight concrete in the density range of 25 Iblfe to replace timber blocking in a raise preparation structure. Other experiments are described in which low-density, lightweight concrete blocks were produced for mine ventilation doors, stoppings, and barricades. Other mine uses reviewed include pillars and collapsing beams. An advantage of low-density concrete is that it will display up to 50% deformation at a constant yield stress. These hlllovative concepts in deformable concrete lining systems will aid mine operators by decreasing capital and maintenance costs, increasing the available space in underground haulageways, and providing productivity gains and improved resource recovery in the soft, caving, squeezing, or bursting grollnu conditions often found in deep mines.

Jan 1, 1989

By W. H. Young

PRODUCTION of bituminous coal and lignite increased substantially in 1964. There were upward trends also in consumption, average value, exports, mechanization, and productivity. However, a significant decline in employment continued. Production.-The output of bituminous coal and lignite in the United States in 1964-487 million tons-was 6 percent greater than the 459 million tons produced in 1963. The gain was attributed largely to expanded consumption by the electric utilities, greater use at coke ovens, and an increase in exports.

Jan 1, 1965

By David E. Swanson

The U.S. Bureau of Mines undertook a basic investigation of collimated abrasive water-jet behavior because a more complete understanding of the fundamental process may lead to further technical advances. Laboratory experiments used 2-mm water-jet nozzles and new entrainment apparatus to analyze collimated abrasive water jets operating under varied conditions. Maximum water pressure was 69 MPa to permit use of conventional hoses with a burst-to-operating-pressure ratio of 4. Nozzle and induction line pressures, abrasive induction rates, and jet reactive thrust forces were recorded for each operating condition. Average jet velocity and power were determined from component mass flow rates and reactive thrust force measurements. Relative velocity and cross-sectional distribution of abrasive particles were determined using impact analysis techniques. Other jet characteristics were determined photographically. Properties of free water jets, collimated water jets, and collimated air-water jets were determined for comparison.

Jan 1, 1989

By N. Grosland, G. Kopp, T. Hunstad, D. Wilder, M. Contratto, S. Rahmatalla, T. Xia

Chronic whole-body vibration exposure, as expected in large construction and mining vehicles, has been associated with neck and back pain and injury.1 While work has been done towards gaining a better understanding of the relationship between vibration and shock and muscle activity of the back musculature2, relatively little information regarding the activity of neck, shoulder and upper arm muscles is known. Today’s equipment designs must conform to domestic and international standards, however these standards do not specifically address the vibration exposure in the head and upper quarter. Further it is not well known how the control configuration within a vehicle (e.g. steering wheel versus arm controls) influences muscle voluntary and reflex activity levels. Greater muscle activity may lead to greater muscle fatigue – which in turn may be associated with greater risk of injury.2 Thus, muscle contractions needed to maintain static postures as well as those resulting reflexively should be considered during an analysis of seating position. Unfortunately, little is known regarding the influence of arm position on head and neck muscle function. The purpose of this study was to investigate the relative muscle activities of 5 neck, shoulder, and upper arm muscles during riding simulations of large construction equipment, using three different arm control options. Methods Five typical heavy equipment ride files were “played back” through a man-rated Servo Test 6-degree of freedom (dof) vibration system. Each ride was repeated using 3 seat and control configurations (steering wheel (SW), floor mounted arm-rest controls (FM), seat mounted arm-rest controls (SM)). Two trials were performed for each ride and seat control combination (each trial: 60 sec of 6-dof and 60 sec of vertical vibration). Five channels of surface electromyography (EMG) of the right-side cervical erector spinae muscles (neck extensors), sternocleidomastoid (neck flexor), upper trapezius (shoulder elevator), biceps brachii (elbow flexor) and triceps brachii (elbow extensor) muscles were collected throughout each ride (~ 2min) using pre-amplified (10x), 1 cm silver bar electrodes, with 1 cm fixed inter-electrode distances (Delsys, Inc). Further analog amplification was set at 10k (1k for one subject), and sampled at 1000Hz using a 12-bit DAQ card and Labview 7.1 software (National Instruments). A total of 7 right-handed male subjects were tested, but only 5 had complete EMG data sets to analyze for this sub-study. EMG was analyzed using root mean square (RMS, in mV) of 20 ms moving windows, and then averaged across the entire trial for a measure of mean total muscle activity (voluntary and reflexive). The muscle activity to maintain the static posture was estimated as the mean RMS EMG over a 1 sec interval just prior to and/or after completion of the ride. Repeated Measures ANOVAs were used to test for with-in subject differences using a = 0.05.

Jan 6, 2006

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By FRANKM. SEIBERT, G. G. Oberfell, GEORGEA. BURRELL

The Bureau of Mines is conducting a series of investigations with the common aim of minimizing the losses that occur in the mining and treatment of mineral substances. The results of the investi- gations are being published in reports of the bureau. This report treats of a method of preventing some of the waste of the natural gas incidental to oil mining. This method, the condensation of gasoline from natural gas, offers to the oil operator and others a profitable means of utilizing some of the oil-well gas now being wasted. The most desired constituent of crude oil is obtained, the production of oil is not hindered, and the gas, after the extraction of gasoline, can be returned to the leased area to drive pumps or into pipe lines for uses to which natural gas is ordinarily put, usually with its fuel value lessened only in slight degree. Publications already issued briefly discuss the subject. In this report the work is treated in greater detail, and the results of many additional tests are shown.

Jan 1, 1915