Search Documents

By CLARENCE G. SMITH

Prior to the actual development of an oil property it is difficult to determine the quantity of oil under the property and the rate at which this oil can be brought to the surface-factors that determine the ultimate value of the property. Consequently, there has been much confusion in devising accounting systems that, during the entire life of a property, will show costs and profits from which the producer can determine whether his property is being worked at a profit or otherwise. The Bureau of Mines publishes this report in recognition of a distinct need for a simple treatise on accounting methods adapted to the peculiarities of the petroleum industry. Probably many companies operating oil wells are not fully acquainted with details important to the welfare of their business, because their account books fail to furnish them with exact and adequate data. With the accountant rests the responsibility of providing the management with reports setting forth the details of the business expressed in fitting terms as well as in dollars and cents. These reports are a means whereby efficiency may be maintained, waste prevented, oil obtained and sold, and money suitably reinvested. They also enable a concern to study the progress of its business in order to conserve to the utmost the possible benefits from an exhaustible deposit of mineral wealth. When managements realize the extent of the waste at their properties more attention will be given to the character of the accountancy records. Herein are presented descriptions and discussions of balance sheets, profit-and-loss statements, and bookkeeping methods peculiarly adapted to the oil business. As far as possible, technical phrases have been omitted in order that those not familiar with accounting terms may be able to follow the subject matter. The systems of keeping books outlined in Chapter X have all been found practical. For brevity as well as clearness the major part of the work refers to the company operating only one property.

Jan 1, 1917

By W. H. Young

In response to increasing national energy requirements. highlighted by the continuing growth in demand for coal for the generation of electric power the output of bituminous coal and lignite in 1965 passed the 500-million-ton mark for the first time since 1956, thus emphasizing the steady up-ward trend from the recent low of 403 million tons in 1961. There were corresponding upward trends in consumption, exports mechanization, and productivity. Production.-The output of bituminous coal and lignite in the United States in 1965-512 million tons-was 5 percent greater than the 487 million tons produced in 1964. The gain was attributed largely to expanded consumption by the electric utilities, greater use at coke ovens, and an increase in exports.

Jan 1, 1967

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Big Buck mine is one of the larger underground uranium-vanadium ore mines on the plateau. The mine is about 39 miles southeast of Moab in the Big Indian mining district, San Juan County, Utah. The Big Buck claims were located late in 1947, when uranium mineralization was discovered in the Cutler formation at its outcrop along the escarpment that forms the west side of Big Indian Wash. Charles A. Steen made the first major discovery of uranium ore in the Chinle formation in the Big Indian mining district on July 6, 1952, when 14 feet of high-grade uranium ore was encountered in a diamond-drill hole drilled on his Mi Vida claim. The Big Buck ore body now being mined by Standard Uranium Corp. is a southeast extension of Steen's original discovery.

Jan 1, 1956

By E. Chin

Although Japan is a major producer of crude steel, it is poor in industrial raw materials. This Bureau of fines report describes Japan's raw material needs for chromium, cobalt, manganese, nickel, and tungsten to produce ferroalloys and alloy steels. Japanese imports of these ores or metals by quantity and source are given for 1972-81, inclusive, to indicate (1) the changes in the consumption and supply pattern, and (2) the degree of Japan's dependence on foreign sources. This report also describes measures implemented by Japan to reduce the risk- of supply interruption, and discusses the possible implications of supply shortages.

Jan 1, 1983

By E. D. Gardner

This paper is a progress report on the study of mining methods and costs in the western United States and summarizes that part of the work pertaining to the undercut block-caving method of mining. Ore is mined on a large scale exclusively by the undercut block-caving method at the following six mines in the western United States: The Morenci branch of the Phelps Dodge Corporation, Morenci, Ariz.; the Ray mines of the Nevada Consolidated Copper Co. at Ray, Ariz.; the Inspiration Consolidated Copper Co. at Inspiration, Ariz.; the Miamo Copper Co. at Miami, Ariz.; the Ruth mine of the Nevada Consolidated Copper Co. at Ruth, Nev.; and the Consolidated Coppermines Corporation at Kimberly, Nev. The undercut block-caving method is also used at the mine of the Andes Copper Mining Co. at Potrerillos, Chile.

Jan 1, 1930

By Merwin H. Howes

In constructing the NORAD Combat Operations Center, controlled blasting techniques were employed to achieve smooth walls and to avoid shattering the rock beyond excavation lines. Extraordinary measures were taken to stabilize the rock to permanently preserve the openings. Rock stabilization was accomplished by means of reinforced concrete and gunite linings, rock boltings, installation of chain-link fabric, and epoxy resin and cement grouting. A particular zone of weakness at a vital location was supported by exceptionally thick reinforced concrete lining, rock bolts, and cement grout.

Jan 1, 1966

This report on the Venezuelan coal industry is the seventh in a series of studies on coal exporting countries requested by the House Appropriations Committee, The committee asked that the basic differences in mining costs for U.S, and foreign mines be identified, especially those costs incurred in complying with health, safety, and environmental regulations.1 Basic costs in extracting raw coal are analyzed in this report for surface operations, This report also provides a limited analysis of the relative market competitiveness of selected Venezuelan and U,S. steam coal mines in three electric utility markets: New England and the east coast of Florida in the United States, and western Europe. Although some Venezuelan coal has coking characteristics, all coal-producing regions of Venezuela sell coal in steam markets.

Jan 1, 1994

By Hillary W. St. Clair

This report describes an experimental method for determining parameters for the rate of reaction of CO2 with solid carbon. The method involves the simulation of a flow reactor by a mathematical model based on a hypothetical multistage reactor which permits calculation of the analyses of effluent gas and carbon consumed as functions of the flow rate and duration of the reaction. The method is applied to experimental data on the reaction of coke with CO2 in fluidized-bed and fixed-bed flow reactors. A method is described whereby two parameters may be determined simultaneously. The method involves a reiterative procedure that finds the values of the parameters that minimize the sum of squares of deviation between calculated and observed analyses of the effluent gas.

Jan 1, 1971

By H. F. Yancey

The development, manufacture, and sale of small coal stokers suitable for domestic use has provided a new industry in the United States at a time when badly needed. Sales of domestic stokers have doubled each year for the past 4 rears, until in 1936 probably more than 90,000 such units were put into use. According to reports of the Bureau of the Census 79,543 residential stokers were sold in the first 10 months of 1937 by 109 manufacturers. This rapid expansion has made itself felt in the coal-mining industry. The smaller sizes of coal, either in a sized or slack condition, are in greater demand; as a result, preparation practices at the mines have had to be revised so that, in many instances, lump coal is being crushed to meet the demand for stoker coal. This situation in turn has necessarily resulted in a realignment of price schedules for the different sizes. One of the first underfeed stokers small enough for domestic use was developed at Seattle, Wash., in 1912; in 1916, a small overfeed stoker was developed at Seattle. These two types are generally considered to represent the beginning of the present domestic stoker industry in the United States. A careful inquiry as to the number of domestic stokers now installed in the Seattle area, made by C. R. Pate, who was detailed to this duty by the Works Progress Administration, indicated that probably 7,000 domestic stokers are being used in this area for residential heating. Most of these stokers axe of the overfeed type, although in the past 2 years the underfeed type has made rapid gains.

Jan 1, 1938

By H. F. Yancey

The development, manufacture, and sale of small coal stokers suitable for domestic use has provided a new industry in the United States at a time when badly needed. Sales of domestic stokers have doubled each year for the past 4 years, until in 1936 probably more than 80,000 such units were put into use, According to reports of the Bureau of the Census 75,543 residential stokers mere sold in the first 10 months of 1937 by 108 manufacturers. This rapid expansion has made itself felt in the coal-mining, industry. The smaller sizes of coal, either in a sized or slack condition, are in greater demand; as a result, preparation practices at the mines have had to be revised so that, in many instances, lump coal is being crushed to meet the demand for stoker coal. This situation in turn has necessarily resulted in a realignment of price schedules for the different sizes. One of the first underfeed stokers small enough for domestic use was developed at Seattle, Wash., in 1912 in 1916, a small overfeed stoker was developed at Seattle. These two types are generally considered to represent the beginning of tie present domestic stoker industry in the United States. A careful inquiry as to the number of domestic stokers now installed in the Seattle area, made by C. R. Pate, who was detailed to this duty by the Works Progress Administration, indicated that probably 7,000 domestic stokers are being used in this area for residential heating. Most of these stokers axe of the overfeed type, although in the past 2 years the underfeed type has made rapid gains.

Jan 1, 1938

By D. G. Puglio

This Bureau of Mines study covers 25 underground mines that were active in the Upper and Lower Freeport and Lower Kittanning coalbeds in 1976. The coal ranges from low to medium volatile in rank; its primary use is for steam generation. Seven mines emit more than 100,000 cfd of methane gas; those mines are the deepest and largest producers. The methane gas content of three core samples of the Lower Kittanning coalbed was estimated by the direct method. A sample from a depth of 320 feet contained 0.5 cu cm of gas per gram, at 620 feet there was 0.8 cu cm of gas per gram, and at 1,060 feet there was 11 cu cm of gas per gram. These results suggest that methane control problems will be encountered in the future as deeper coal is mined.

Jan 1, 1979

By P. H. Francis

In This report, factors which currently enter into the design, manufacture, and quality assurance of explosion-proof enclosures are reviewed, with special emphasis given to the sealing concepts and sealants/cements, per se, for lenses. The physical and mechanical properties of a number of representative sealants and adhesives are measured, and found to exhibit great variance, with few discernible trends which might afford a firm base on which to establish minimum property standards. Accordingly, acceptance criteria for adhesives and sealants are suggested based on the survivability of an explosion-proof enclosure as a structure rather than upon the minimum mat real properties of its constituents. Procedures or surface preparation of adherends, and for quality assurance, also are proposed.

Jan 1, 1980

By Lincoln A. Stewart, P. S. Haury

"INTRODUCTION AND RESUME Arizona asbestos mines are the only sources on the American continents of iron-free chrysotile spinning fiber that meets the Navy specifications for asbestos fiber for use in covering electrical cables. Rhodesia normally supplies the bulk of this grade of asbestos at about half the Price of Ari zona spinning fiber. The acute submarine menace in 1942 focused attention on the danger that imports might be cut off and that a sudden demand for greatly expanded production might fall on the Arizona mines to supply the tonnage of this essential material needed for war production.A joint preliminary investigation of Arizona asbestos deposits was made in August 1941 by J. R. Thoenen, senior mining engineer of the Bureau of Mines and A. E. Granger, a geologist of the United States Geological Survey. A more extended investigation of the numerous asbestos mines and prospects, which are scattered over 25 townships of difficult terrain in Gila County, was begun by the senior author in August 1942.The Geological Survey assigned two geologists (Newton Chute and A. F. Shride) a few weeks later to study the geology as an aid in selecting the mines for the Bureau's exploration projects. Six mines were selected for exploratory work because it was desired to prove reserves of ore where production could be started quickly if urgent demand should arise. Acceleration of production is normally slow because of adverse operating conditions. First, the mines are at distances of 35 to 100 miles from Globe, the shipping and supply point, and the roads are few and poor. The mine openings start in steep canyon walls, so that mining supplies usually have to be packed in and the product packed out over 0.5 to 5 miles of burro trail. Second, most of the ore deposits are small, and the ratio of rock broken to spinning fiber recovered is very high, usually exceeding 200."

Aug 1, 1947

The Mine Safety and Health Administration (MSHA) defines an independent contractor as any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine. Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Jan 1, 2008

By Terry Muldoon

In conventional noncoal, room-and-pillar mining, the cutting machine is frequently a major source of airborne dust. Water is often used for dust control. An evaluation of typically used water systems during this program showed that they reduced dust levels by 60 to 70 percent over dry cutting when at least 0.5 gpm of water was applied. These systems, however, are only marginally effective in maintaining compliance levels and the added moisture causes operational problems. During the program, three additional dust control systems were designed, fabricated, and evaluated. The first, a hollow cutter bar, was designed to capture dust in the kerf at the cutting zone. The system was only marginally effective in reducing dust levels due to its lack of control of other sources. Large quantities of material captured by the system made it operationally questionable. The second, a machine mounted exhaust system, was extremely effective in capturing virtually all the dust generated in the heading. The captured dust was ducted out of the heading and exhausted downstream in the crosscut. Exhausting the dust without scrubbing, however, creates problems for personnel working downstream of the cutting machine. Successful application would require changes to the mine ventilation system and mining sequence. The third, foam, injected foam from an onboard generator through a channel to the cutting zone at the tip of the bar. Test results showed that foam, using 1/3 to 1/2 the total fluid quantity, was equally effective when compared to the mine's current water system.

Jan 1, 1983

By Will H. Coghill, F. D. DeVaney

"Many of the iron ore deposits on the western end of the Mesabi Range Minnesota consist of the so-called ''wash ores."" Because of their high silica content these ores must be washed or concentrated to make them merchantable. Washing plants have been in operation for 20 years, during this period large quantities of tailings have accumulated in tailings ponds. These tailings contain the aggregate millions of tons of iron oxides which, if recovered, would greatly to the available tonnages and to the revenues of the mining companies. It the purpose of this paper to outline give results of concentration tests on tailings.In order that the reader may understand more clearly the type of material under consideration, a short description of the characteristics of the wash ores of the Western Mesabi Range and a brief resume a washing methods that have been are now being employed will be given. Appleby and Newton4 In their description of the district and of the ores say:The Western Mesabi district embraces the territory west of the town of Nashwauk in Itasca County. The territory to the east of this dividing line is known as the Central and Eastern Mesabi district. This subdivision is rot wholly arbitrary. While the ore bodies in the two districts resemble each other in. shape, size, and general structure, there is a marked and very important difference in the character of the respective ores. For purposes of comparison, the western deposits have been called washable ore bodies, and the central and eastern, standard ore bodies. The latter ores are the result of natural concentration processes which have teen carried far enough to produce a large proportion of high-grade ore Wet can be marketed direct; the Western Mesabi ores present a lesser degree of natural concentration and are as a rule of too low grade to admit of marketing without preliminary treatment. In many cases the grade can be improved by washing, hence the material is called washable ore. Exceptions to thin general rule may be noted in both districts. Many of the Western Mesabi ore bodies contain quite a proportion of merchantable ore. There are also portions of central and eastern Mesabi ore deposits which are of low grade and which can be improved by washing."

Nov 1, 1930

By S. B. Christy

This report on the electrodeposition of gold and silver from cyanide solutions represents work that has occupied my time at intervals during the past 20 years. The investigation has been carried on simultaneously with my duties as professor of mining and metallurgy of the University of California. During shis long investigation I have been assisted in the details of the work by, a number of my former students, acting in turn as assistants. Particular mention in this connection is due W. H. Hilton, who graduated in 1900; C. T. Dozier, 1902; N. C. Stines, 1905; H. N. Herrick, 1907, and L. C. Uren, 1911. It is impossible to publish full details of the many thousands of experiments performed. Effort has been made to present only the essential data. Wherever possible, the results of the experiments have been expressed in diagrammatic form by curves showing the relation between the simultaneous variables of the experiments. It is necessary to show, as nearly as may be, the state of the art. This is difficult because of the meager literature on electrodeposition in the cyanide process; hence resort must be had to the specifications and claims of patents, most of which seem never to have been applied on a working scale. Such information consequently can not be taken at its face value. Expressing the essential ideas evolved in such specifications is no easy task. Clearly, in quoting from patent records it is not ·feasible to enumerate all of the specifications or the claims allowed the inventors. A statement of the chief contributions to the art in the patent cited must suffice. Legal details, of course, must be obtained from the original patent. In the study of patent literature, when one compares the ardent hopes of the inventors with the results realized from their efforts, it becomes clear that in the development of an art no one man contributes everything. Each subsequent inventor stands on the shoulders of the one who has gone before. It is only through the summation of the contributions of many inventors that the art as a whole prospers. On October 19, 1887, a British patent was granted to McArthur and Forrest for the use of dilute cyanide solutions for treating gold and silver ores. The rapid extension of this process, in various forms, all over the world, has almost revolutionized the treatment of ores containing precious metals. It is a remarkable fact, however, that long before this patent was granted there was issued, on February 5, 1867, to J. H. Rae, U. S. patent 61866, for an electrocyanide process. Thus a method of electrodeposition from cyanide solutions used for treating ores was invented 20 years before the McArthur and Forrest patent .was granted, although the process did not come into general use. On May 24, 1889, U. S. patent 403202 was granted to McArthur and Forrest for the use of zinc shavings for removing gold and silver from cyanide solutions. The use of finely divided zinc is still the standard method for recovering 'gold and silver from cyanide solutions. Since this patent was granted, many attempts have been made to replace the precipitation upon the zinc by methods of electrodeposition. It is the purpose of this report to give an outline of some of these methods, as well as to show the relative advantages and disadvantages of the zinc and the electrical methods of recovering gold and silver from cyanide solutions.

Jan 1, 1919

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include better fire suppression systems, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By Theodore M. Katz, W. Stephen Brightwell, David E. LeGrande, Joseph J. Hurrell, Jane A. Lipscomb, Nancy Lessin, Lawrence R. Murphy, Michael J. Colligan, Steven L. Sauter, Richard A. Lippin

Revolutionary changes in the organization of work have far outpaced our knowledge about the implications of these changes for the quality of working life and for safety and health on the job. This gap in knowledge is one of the 21 priority areas for research under the National Occupational Research Agenda (NORA)—a framework crafted by the National Institute for Occupational Safety and Health (NIOSH) and its partners to guide research into the next decade. This report was developed under NORA as the first attempt to develop a comprehensive research agenda for investigating and reducing occupational safety and health risks associated with the changing organization of work. Research and development needs identified in the agenda include (1) improved surveillance mechanisms to better track how the organization of work is changing, (2) accelerated research on safety and health implications of the changing organization of work, (3) increased research focus on organizational interventions to protect safety and health, and (4) steps to formalize and nurture organization of work as a distinctive field in occupational safety and health.

Jan 4, 2002

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure" or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", "canopies", "roll bars', "protective structures" and other such descriptive names. In this report, 'ROPS" describes the function of the structure; 'FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection.

Jan 1, 1976