Search Documents

By K. L. Williams

The Bureau of Mines tested a prototype tapered-element oscillating microbalance (TEOM) dust monitor for measuring respirable coal mine dust. The monitor uses the inertial behavior of a vibrating element to measure the mass of sampled dust. Tests were performed to determine variability, drift, the effect of humidity, placement of collection filter, and element orientation during analysis, and comparability with gravimetric measurements of respirable coal dust. Variability was about 1.6 µg. Over about 26 h at 46 pct relative humidity, drift was very slightly negative. When the relative humidity was increased to 78 pct, all units showed a total positive change less then 40 µg over about 70h. Filter placement variation on the tapered element resulting from in- consistent sizing of the filter mounting bases caused significant error (up to 0.2 mg). In practice, calibration of the system for each new filter will eliminate that error. Orientation of the element during analysis did not introduce significant error, but care is necessary when mounting the canister that houses the element to avoid damping oscillation of the element. Dust tests were performed in an aerosol chamber using coal dust. Measurements made by the TEOM dust monitor agreed to within 10 pct of simultaneous measurements by gravimetric personal samplers.

Jan 1, 1986

By Laurence G. Trudell

Geology and oil-yield data are presented for a 58-square-mile area encompassing the U.S. Department of the Interior oil-shale leasing program tracts in the western Washakie Basin, Sweetwater County, Wyo. Lithology and oil yields of samples from three Bureau of Mines coreholes are evaluated and correlated with Kinney Rim surface sections measured and sampled by the U.S. Geological Survey. Minable sections of oil shale averaging up to 25 gallons of oil per ton crop out on Kinney Rim in the Laney Member of the Green River Formation. Thick oil-shale sections in the Laney Member that average 15 gallons per ton represent 155 million barrels of oil in place per square mile. In the lower part of the Green River Formation the Tipton Shale Member contains a 20-to 40-foot section averaging 15 gallons per ton. Beds of high-volatile C bituminous coal up to 6 feet thick are present in intertongued parts of the lower Green River Formation and upper Wasatch Formation.

Jan 1, 1973

By L. D. Schmidt, W. C. Schroeder, A. C. Fieldner

"INTRODUCTION The highly mechanized character of modern warfare makes steel the most vital raw material. The shortage of steel scrap in the United States is forcing the use of increased quantities of pig iron in steel manufacture, so that the rate of pig-iron output will continue to be the controlling factor in steel production. 5/ At the same time, the construction of new blast furnaces is limited both by time and the amount of strategic material available. Under such circumstances, every effort must be made to attain and then maintain maximum pig-iron output from the equipment now in use.When forcing a blast furnace to the ultimate in production the highest standards for quality and uniformity of the coke must be maintained. In view of these facts, the Bureau of Mines, in cooperation with the Office of the Solid Fuels Coordinator for War, is surveying the coke industry to study the various steps in producing coke of higher quality and greater uniformity. 6/ The engineers conducting the survey are visiting key men in coke-oven and blast-furnace organizations to determine, first, the major and most common problems in coke production and use; and, second, the best and quickest method for solving them. Various operators have made good progress in solving individual problems, and a Nation-wide exchange of information among them will make possible widespread adoption of the best practices. It is the purpose, of the survey and reports such as this preliminary one to facilitate such exchange of information. As an outgrowth of the survey, it was soon revealed that many operators could be helped by cooperation with various Government agencies, particularly to procure suitable coals, minor additions to equipment facilities, and tests on certain properties of coal or coke, or specific advice concerning the operation of various types of equipment. The machinery and organization necessary for securing this cooperation have been set up as a part of this work."

May 1, 1943

By Amanda S. Azman

It is known that exposure to high sound pressure levels can lead to permanent hearing loss; however, many workers, in mining as well as other occupational sectors, frequently receive hazardous noise exposures. The National Institute for Occupational Safety and Health (NIOSH) recommends using a criterion level of 85 dB(A) for implementation of hearing loss prevention programs1. But, despite engineering and administrative controls, workers continue to exceed their recommended daily noise dose. Hearing protection devices are worn as a final defense against noise overexposure, but many workers have difficulty communicating or detecting warning signals while wearing them. New electronic technology has been integrated into conventional hearing protectors to allow for some degree of sound restoration. Research is currently being carried out within NIOSH, Pittsburgh Research Laboratory (PRL) to evaluate the performance of sound restoration hearing protectors. Due to certain features of the devices, such as their non-linear performance and possible manipulation of electronic settings, there are obstacles to testing them using the existing standard hearing protector test methodology (ANSI S12.42-1995 and ISO 4869-3:1997). These and other issues related to testing these devices are outlined within this paper, and possible solutions are discussed. Measures of attenuation properties have been done on a set of the devices and preliminary findings indicate that new test methods, or at least modifications of existing methods, must be developed to accurately determine device performance. Furthermore, it is necessary to know not only the attenuation properties of such devices, but also the degree to which speech intelligibility or recognition of warning signals is preserved, as compared with conventional hearing protectors. As additional data is collected a more accurate and reliable test methodology will be developed, and a more comprehensive picture regarding device performance will be determined and disseminated.

Jan 1, 2008

By F. S. Wartman

This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic Chloride with magnesium, grinding, leaching, and magnetic-separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described and some data on operating costs are given.

Jan 1, 1949

By Geoffrey C. Huggins

Diagnostic: tests were performed on a production ST-5A Load-Haul-Dump machine manufactured by Wagner Mining Machinery Company to evaluate and rank order noise sources. The diagnostic evaluation indicated that the major noise sources were the transmission, the engine, and the cooling fan. This phase was followed by implementation of recommended noise control treatments, which included vibration isolation of the transmission, a transmission enclosure, an engine enclosure, and modifications of the inlet to the cooling fan. The final step in the program was an underground operational period which began on 31 August 1976 at the National Gypsum Mine in Shoals, Indiana. The noise control treatments successfully reduced the LHD operator noise exposure by 7 dB(A), thus increasing its allowable operation time by a factor of 2.7. Actual measurements made underground using noise dosimeters have indicated that, during, a typical shift, the noise control treatments have reduced the fractional exposure to an allowable level. The report discusses the mechanical aspects of the LHD, its noise sources, the treatments applied, the final levels achieved, and field experience with the noise-controlled machine.

Jan 1, 1977

By David L. Bickel

Stress-relief techniques and instrumentation have been developed through many years of research in the Bureau of Mines and successfully used to determine the in situ state of stress in rock. This report describes the Bureau's three-component borehole deformation gauge and the drilling equipment and accessories used with it. Operation and calibration procedures for the deformation gauge are discussed in detail, along with site selection and overcoring procedures. Information and references included in this publication provide a guide to the Bureau's cover-coring method for determining rock stress.

Jan 1, 1985

By Chas. F. Jackson

This paper is one of a series dealing with special mining problems and forming part of a general study of mining, methods and costs being conducted under direction of the Bureau of Mines. A considerable part of the material assembled and discussed in this paper has been gathered from articles on individual mines written by consulting engineers to the bureau who are engaged in active mine operation at the properties described, while other data have been taken from the technical press or gathered from personal observations. OBJECT AND SCOPE OF PAPER C. F. Jackson4 ha[-] pointed out that underground transportation (tramming, haulage, and hoisting) absorbs an appreciable percentage of the total underground cost of most mines, averaging for different methods of mining 12.9 to 28.4 per cent of the total underground cost. In general the percentage of cost accounted for by transportation was shown to be highest for the low-cost mining methods.

Jan 1, 1931

By Alfred L. Ransome

GOLD output in Alaska in 1950, following a 2-year decline, increased to the highest point since 1942. Tills unexpected gain in production of the Territory's greatest value commodity was largely responsible for the increase in the over-all value of mineral output in the Territory to $17,852,000 from $15,549,000 in 1949. Although coal continued to rank second to gold in value of output, production was slightly less than the record production of 1949. The mining of platinum continued to be an important factor in the mineral industry, with production of crude platinum metals exceeding that of 1949. The output of lead was three times the 1949 production, and silver gained 46 percent over the previous year's total. Copper and zinc production-entirely as byproducts from other ores-showed an increase, but remained minor. Production of tin was relatively small, but substantially above the total for 1949.

Jan 1, 1953

By Albert L. Toenges

This paper is the fourth of a series5/ that describes some methods and practices of mining coal mechanically where operations are conducted on more than one shift. Many inquiries have been received regarding methods of extracting pillars with mechanized equipment, and this paper deals primarily with this phase of mechanical mining. Some of the questions that have been asked are:

Jan 1, 1942

This report presents depth and producing rate statistics pertaining to oil reservoirs (or fields) in each of the 14 States that produced more than 20 million bbl of oil during 1965. The combined oil production was about 2.6 billion bbl, or 96 pct of the U.S. total. Data are presented for each of the 14 States, each Texas Railroad Commission district, and four geographical areas of Louisiana. About 8 pct of the total oil produced in the 14 States was from depths of lees than 2,000 ft, 24 pct from 2,000 to 4,000 ft, 22 pct from 4,000 to 6,000 ft, 16 pct from 6,000 to 8,000 ft, and 30 pct from 8,000 ft and deeper. The average production per well in the 14 States ranged from 4.4 bopd for wells less than 2,000 ft deep to 57.6 bopd for wells 8,000 it and deeper. Data indicate that 9.5 pct of the 460,968 wells produced more than 1.2 billion bbl or 46.6 pct of the total oil. Oil production from reservoirs (or fields) not undergoing stimulative recovery operations, such as steam, air, gas, or water injection, wee about 1.1 billion bbl or 42.1 pct of the total.

Jan 1, 1967

By Robert N. Roby

This report is one of a series based upon investigations made and being made within the Missouri River Basin in Montana by engineers of the Bureau of Mines , Albany Branch , Mining Division . These investigations are made primarily to provide preliminary information to Department of Interior agencies and others concerned with the planning of the proposed Federal power developments within the Missouri River Basin . The present report has been designed to permit public distribution of the factual data obtained . The field investigations in Meagher County were made during tually all 1948 ; Vir- known metallic mineral occurrences within the county were investigated ; some nonmetallic mineral deposits also were investigated . The investigations cannot be considered complete , however , because some long-inactive mines or prospects may have been missed . Most of the old mine and prospect openings are caved; many are completely inaccessible . Many of the claims located years ago have been abandoned ; others have been relocated under different names and ownerships . Because of such conditions , much of the information regarding their development and operation necessarily has been obtained from Federal and State publications , supplemented by information provided by owners and local residents .

Jan 1, 1950

By W. A. Stickney

The Bureau of Mines conducted beneficiation and smelting studies on siliceous offgrade manganese samples to indicate effective methods of manufacturing silicomanganese from materials that cannot be economically beneficiated to meet General Services Administration (GSA) specifications for stockpiling. Laboratory and pilot-plant flotation tests were conducted on 2 samples, 1 from the waste-tailings dump of the Domestic Manganese & Development Co , Butte, Mont., and the other from the Nettie mine in the Butte-Philipsburg area. Smelting tests were made on the combined concentrates from the pilot-plant flotation tests and on part of the tailings sample The flotation scheme found to be adequate in laboratory tests and later in the pilot-plant tests consisted of flotation by a fuel oil-tall oil emulsion in an acid circuit (pH )-1-.8 to 5.0). The oil-emulsion reagent flocculated the manganese minerals and selectively floated them from the siliceous gangue, In the pilot-plant flotation test on Butte-mill tailings 90.1 percent of the manganese was recovered in a concentrate that analyzed 32.6 percent Mn, 4.8 percent Fe and 28.1 percent Si02. In the test on Nettie mine ore 90.8 percent of the manganese was recovered in a concentrate that analyzed 36 6 percent Mn, 5.5 percent Fe, and 26-4 percent Si02.

Jan 1, 1956

By R. J. Leary

The Bureau of Mines experimental blast furnace was blown with oxygen-enriched blast in combination with natural gas injected at the tuyeres. The air blast was augmented with oxygen to form an enriched blast containing 24,8 pct oxygen, and tests were run at natural gas injection rates of 4.5, 6.0, and 8.3 pct of the air blast. Similar enrichment to 26.8 pct oxygen was tested at natural gas rates of 7.2, 9.1, and 11,0 pct of the air blast. At intermediate proportions of natural gas to oxygen, (1) the fuel rate and the replacement ratio of coke by natural gas were unaffected by oxygen injections and (2) the productivity increased about 4 pct for each I pct oxygen added to the blast. The higher proportions of natural gas to oxygen were less efficient; in return for a lower coke rate, the fuel rate increased and productivity declined. A deficiency in reducing gas imposed a limit upon lower than normal proportions of natural gas to oxygen. Beyond this limit the formation of reducing gas was insufficient to support the rate of metal production. When this condition was encountered, the coke rate requirement for specification iron was abnormally high and production fell off badly. Adiabatic flame temperature is discussed as a means for proportioning oxygen and natural gas additions.

Jan 1, 1967

By N. H. Darton

This report presents the results of an investigation begun by the Government in the summer of 1907, the investigation being started under the immediate supervision of Dr. J. A. Holmes and continued under him as director after it was transferred to the Bureau of Mines in 1910, the field studies being completed in the spring of 1912. The purpose of the investigation was to obtain information on the origin of the inflammable gases in coal and the conditions under which they occur. It was especially intended to ascertain whether there was any relation between the occurrence of gas and the structural or other geologic features of the coal beds. To this end many months were spent in mines and much time was devoted to the examination of mine maps, bore-hole records, and other data made available by the kindness of various coal companies. Two fields of work were selected-one in the northern anthracite basin of Pennsylvania, where the beds are considerably flexed, and the other in the southern part of the bituminous coal field of Illinois, where the beds lie nearly horizontal. In order to take advantage of results of previous investigations of the same general subject, an extended examination was made of reports of various investigators in Europe and America. A digest of the information obtained from these publications is included in the first part of this report, which constitutes an introduction to the discussion of the conditions governing the occurrence of inflammable gas in coal beds.

Jan 1, 1915

By John C. Hartley

Large areas of the anthracite beds in the Wilkes-Barre, Pa., region have been first-mined in such a manner that over half of the original coal has been left underground as pillars to support the overburden. To recover the maximum amount of this remaining coal, improved devices to support the roof while pillars are being extracted are needed. Also needed are suitable backfilling systems that will stabilize the strata during the mining and effectively limit the inevitable subsidence after pillars are removed. Accordingly, the Federal Bureau of Mines furnished 400 yielding steel props that had been purchased abroad, where this type of prop had been used successfully. The cooperating company arranged for concurrent tests with a mechanical stower designed and built by an American manufacturer. In the area in which the experiments were conducted, pillar removal, using conventional timbering, was most difficult because the roof fractured badly, the installation of timbers consumed a substantial part of the work effort, and some coal nearly always was lost. With the application of the yielding props, the time needed for securing the roof was reduced 33.9 percent; production per man-shift was in¬creased over 33 percent; coal recovery was improved more than 9 percent; and the convergence between roof and floor, during mining and backfilling, amounted to as much as 8.03 inches without any break in the roof. However, in September 1953 some roof rock fell in pillar 10 owing to insufficient props in a small area where the ends of three top holes drilled in the coal face extended up into the roof rock.

Jan 1, 1956

By L. A. Eros

The U.S. Bureau of Mines and Western Fuels Utah, Inc. entered into an agreement to plan, install, and evaluate a micro-computer based monitoring and control system at Deserado Mine, an underground coal mine. The U.S. Bureau of Hines contracted the Colorado School of Mines (CSN) to independently evaluate the project. CSM evaluated and documented costs, benefits, problems, and management and labor perceptions in this report. Recommendations are provided for mine operators and monitoring system vendors considering future installations.

Jan 1, 1986

By Thomas S. Jones

This Bureau of Mines publication reviews characteristics, manufacture, and uses of natural and synthetic iron oxide pigments. Supply and demand trends within the domestic industry and in foreign trade are presented for 1955 through 1976. Iron oxides are expected to continue in demand for traditional uses, and if anything, to be favorably affected by technological developments. Imports have been significant in relation to domestic production, most notably for synthetic oxides from West Germany and Canada.

Jan 1, 1978

By L. A. Neumeier

A refinement of the tungsten-cobalt phase diagram is presented for compositions to 85 at. pct cobalt and for temperatures to the solidus. Preparation of alloys by powder metallurgy methods is described, and the results of studies made by a combination of techniques involving microscopy, X-ray diffraction, thermal analysis, and dilatometry are discussed. The existence of u-W6Co7 is confirmed (rhombohedral D85 structure). The W6Co7 phase forms periectically at 1,685'115° C by reaction of liquid with primary W; the peritectic melt is at 71 at. pct cobalt. The homogeneity range of u-W6Co7 extends to both sides of the ideal stoichiometric ratio, through a compositional range of about 5 at. pct. The compositional limits for u-W6Co7 vary slightly below 1,471°±5° C, the temperature of the eutectic reaction forming u-W6Co7 plus a. The eutectic composition is at 79 at, pct cobalt. The existence of WCo3 is confirmed (hexagonal D019 structure). WCo3 forms peritectoidally at 1,093°±5° C by reaction between a and u-W6Co7 and exists over a narrow homogeneity range of 0.5 to 0.6 at. pct. The solid solubility of cobalt in tungsten is low (maximum 0,9 at, pct cobalt) and results in contraction of the tungsten lattice. Tungsten is extensively soluble in a-Co at higher temperatures; the a-Co lattice is expanded by the presence of tungsten in solid solution. There was no indication of the formation of a o-phase nor of any intermediate phases other than WeCo7 and WCo3. The WeCo7 and WCo3 phases are compared with similar phases in other systems.

Jan 1, 1967

By Ivor Hawkes

This report describes how longitudinal and bending stress waves in' percussive drill rods generate noise. It is shown that in practical drills the largest noise source is the bending waves, which are mainly generated because of imperfections in the piston, chuck, and drill rod alignment. Equations are presented which enable the noise spectra generated by the bending and longitudinal waves to be precisely predicted. Means for reducing the amplitude of the bending waves are discussed.

Jan 1, 1977