Search Documents

By R. R. Wells

As a part of the strategic mineral program, examining engineers of the Bureau of Mines collected samples several manganese properties in Colorado. As all of the ores were too low-grade to be acceptable to manufacturers of ferromanganese, beneficiation studies were required .to determine the amenability of the ores to concentration. Manganese in the form of impregnations in sedimentary beds is found in the Denver plains area a few miles east of the Rocky Mountain front. Deposits are reported to occur intermittently over a distance of more than 200 miles. The manganese oxides occur in beds of conglomerate or arkosic sand, generally accompanied by limonite. The Manganese and iron oxides,, however, usually are found in separate layers. Three samples were submitted for beneficiation tests, two samples from Buckley Field bombing Yang, Arapahoe County, and one from near Franktown, Douglas County.

Jan 1, 1952

By W. W. Adams

"The fifth annual National Safety Competition conducted by the United States Bureau of Mines to determine the best safety records at mines and quarries during the calendar year 1929 has been concluded, and the general results of the contest are presented herewith. To the winner in each of the five groups into which the contestants were divided there has been awarded the bronze trophy 'Sentinels of. Safety,' donated by the Explosives Engineer magazine. The trophy for bituminous coal mines was won by a mine in Alabama; that for metal mines by an iron-ore mine in Michigan; that for nonmetallic mineral mines by a salt mine in New York; that for quarries and open-cut mines went to a limestone quarry in Michigan;. the trophy provided for anthracite mines was, of course, won by a mine in Pennsylvania, as all of the anthracite mines participating in the contest are situated in that State.Winners of the trophies were selected by a committee of sward in accordance with rules governing the contest and on the basis of accident records furnished by the various companies to the Bureau of Mines. These records were summarized by the bureau and the results submitted to the committee. Members of the committee are W. H. Cameron, managing director of the National Safety Council. William Green, president of the American Federation of Labor; James F. Callbreath, secretary of the American Mining Congress; T. T. Read, Vinton professor of mining of Columbia University and editor of 'Mining and Metallurgy'; C. B. Huntress, executive secretary of the National Coal Association; A. J., Curtis, assistant to the general manager of the Portland Cement Association; A. T. Goldbeck, director of the engineering bureau of the National Crushed Stone Association.Thirty-four States were represented in the l29 contest. Among the plants which participated were 68 bituminous coal mines, 29 anthracite mines, 54 metal mines, 19 nonmetallic mineral mines, all of the foregoing being underground mines, and 141 quarries or open-cut mines. A total of 106,533,006 man-hours of work was reported by all of the companies. Accidents during the year numbered 7,008 and represented a period of disability equal to 986,306 man-days. Hence the accident-severity rate for all plants combined represented 9.3 man-days of disability for each thousand man-hours of exposure to hazard. Similarly, the combined accident-frequency rate for all plants showed that 66.3 accidents occurred for every million man-hours of exposure to hazard. Both of these rates indicated an improvement over the combined rates for all plants in the previous year's contest. The reduction in the accident-severity rate centered chiefly in the metal mine group, though all except the quarry and open-cut mine group shared in the reduction; the improvement in the accident-frequency rate was in all croups except anthracite and metal, the rate for the former having increased while that of the latter remained unchanged."

May 1, 1930

By R. E. Brewwe

"INTRODUCTION Anyone who has had frequent occasion to compare methods of analysis and testing as employed in European countries with those used in the United States has felt the need of a table or graph giving the relationship between the units of measurement of finely powdered materials. Most of the few published comparisons include only two series of sieves and often require tedious interpolations to adapt the data of one series to the series more familiar to the reader. To eliminate such deficiencies, the author hopes that the discussion and comparison of fine-series sieve sizes presented here will conserve the time of interested research workers.ACKNOWLEDGMENTSThe author is deeply indebted to Virginia B. Strathearn, scientific aide, for help in compiling the information from the literature and to W. A. Solvig, senior chemist, for valuable suggestions in preparing the manuscript.SQUARE-MESH-SIEVE SERIES OF DIFFERENT COUNTRIESSieving analyses of powdered materials have been placed on a comparable basis in different countries by the introduction and adoption of standard sieve-scale series. Series of wire-cloth square-mesh sieves in common I oratory and industrial use include: Institution of Mining and Metallurgy standard laboratory screens (I.M.M.); British Standards Institution standard for fine-mesh test sieves (B.S. or B.S.I.); Tyler standard sereer-scale sieves; United States standard sieve series; Deutsche Industrial-Nermen (DIN); and the standard control sieves of the Association Francaise de Normalisation (AFNOR). With the exception of the I.M.M. series in which the opening is equal to the diameter of the wire, the general proportions of the various series of sieves are similar. The size of British and American sieves is designated by the number of meshes or openings per linear inch or, more recently, by the number of microns per linear sieve opening. In a technical sense the word ""mesh"" is meaningless, unless the diameter of the wire is also given, so that the size of the opening can be determined. On the Continent sieves are designated either by the nunber of Mesh per linear centimeter or by the number of openings per square centimeter."

Jul 1, 1944

By O. M. Bishop

"SUMMARYAs a result of the increased demand for fluorspar during the war, the Bureau of Mines investigated numerous fluorspar properties in the southern Illinois field, which is centered in Rosiclare. Among these the J. J. Shelby 40-acre tract on the western edge of the district presented favorable factors that caused it to be chosen /or exploration.H. G. Spiller, formen lessee of the property, had explored the Shelby vein by means of an adit level and winze, and showed it to contain goad values in zinc and fluorspar at the depth explored. A diamond-drill hole with which Spiller explored the vein 78 feet southwest of the winze, however, failed to cut ore. After studying the field evidence, the Bureau concluded that the vein merited further exploration, particularly at a depth of about 440 feet, where the Fredonia limestone would form the foot-wall of the vein and the hanging wall would be the competent Cypress sandstone.Between October 17, 1944, and March 26, 1945, three diamond-drill holes were bored for a total inclined depth of 1,592 feet. Holes 1 and spaced approximately 500 feet apart, explored the vein at 440 feet 4 below the surface. The economic mineralization existed in the vein where cut. Hole 3 cut the fault at approximately 300 feet below the outcrop but failed to find any vein matter except stringers of calcite with small amounts of pyrite."

Apr 1, 1947

By R. Lindsay Mundell

In the first half of 1990, lessening of cold war tensions was welcome. But Iraq's invasion of Kuwait in August led to the Persian Gulf War in January and February 1991. The subsequent oil shock contributed to a dampening of the U.S. economy, and the U.S. gross national product rose only 0.9 % to $5,463 billion (U.S. billion = 109). The buildup of military forces in the Persian Gulf area focused greater attention not only on petroleum but also on other strategic materials. The U.S. Department of Defense continued to review stockpile goals and upgrade several mineral materials. In addition, the U.S. Bureau of Mines continued to maintain the standby Emergency Minerals Administration. After the Defense Production Act, which authorizes priorities, allocations, and supply expansion, lapsed on October 20, 1990, the Selective Service Act of 1967 became the authority to ensure that orders of the Armed Forces and defense atomic energy programs were given priority treatment.

Jan 1, 1993

During fiscal year 1966 the Bureau of Mines published 99 scientific and technical papers and engaged in 67 research projects on petroleum, natural gas, and oil shale. A basic appropriation of $3.4 million was supplemented by $1 million in cooperative funds from other Governmental agencies and industry groups. Petroleum conservation was advanced by development of scientific knowledge and improvement of technologic methods in both the extraction and utilization of petroleum, natural gas, and oil shale. Experimental work was carried out at research centers in Bartlesville, Okla., and Laramie, Wo., and in laboratories in Morgantown, W. Va., and San Francisco, Calif. ACHIEVEMENTS IN FISCAL YEAR 1966 Bureau of Mines--Petroleum Research in fiscal year 1966 (July 1, 1965- June 30, 1966) was involved in many public issues--air pollution, peaceful uses of nuclear explosives, utilization of oil-shale resources, computerization of recovery-stimulation techniques, and fuels for supersonic airplanes. Scientific contributions included compositional studies of petroleum and oil shale, determination of thermodynamic properties of petroleum compounds, development of analytical techniques, and correlations of petroleum properties with geologic occurrence. Technologic advances included rock-fracturing research, in situ combustion studies, waterflood techniques, use of radio-tracers to study stability of petroleum fuels, and hydrogenation as a tool to prepare shale-oil products.

Jan 1, 1968

According to industry representatives, U.S. producers were listing unalloyed 95.5 percent aluminum ingot in October at 53-57.5 cents per pound, but reportedly much is being priced at 53 cents. New York dealers raised their October positions by about 3 cents to 56-56.5 cents, mainly to cover spot supply shortages. London Metal Exchange 3-month forward contracts traded up in October from 52.3 to 57.3 cents per pound and closed at 56.4 cents. ASBESTOS The Jaquays Asbestos Corp. has announced the imminent closure of its mine and mill in Globe, Arizona. This is the last asbestos producer in the State having operated continuously, except during the early thirties, since 1914. Cost of compliance with environmental regulations was given as the reason for closure.

Jan 1, 1978

By O. M. Bishop

From October 1943 to March 1944, the Bureau of Mines conducted core drilling at the Victory fluorspar mine, Hardin County, Ill. to test the Fredonia limestone and the included sub-Rosiclare sandstone zone beneath the existing stopes. Twenty-one vertical holes were drilled to an average depth of 60 feet. Ore was penetrated in six holes. Since its discovery in 1927, the Victory mine has produced approximately 5 percent of the total fluorspar mined in the United states after that date. The ore discovered in the early mine development is now exhausted, except that contained in pillars drifting to the northeast has partly developed one substantial ore body, and company drilling has indicated another nearby. The increasing need for fluorite for war use in 1943 suggested the desirability of mining the pillars, provided it could be established that no ore beds existed below the stopes or in areas to which access would be obtained through the present workings. This work describes the work accomplished during the project and presents the data obtained.

Jan 1, 1948

By R. L. Cosgriff

A commercial, battery-powered mine vehicle has been equipped for remote operation in coal mines. This vehicle is controlled by an operator from the remote station. Command signals originating at the remote station as well as video and data signals originating on board the vehicle are relayed between the remote station and vehicle using a single coaxial line. This coaxial line is normally 2,000 feet in length and is reeled in and out from a drum mounted aboard the vehicle The vehicle has a maximum speed of 6 ft/sec and a minimum speed of 4 ft/sec using 36-volt excitation of the traction motor. If this traction motor is excited by two of the three batteries, 24-volt excitation, the vehicle will travel at approximately 2 ft/sec. The speed can be reduced by the operator to 1 ft/sec. This vehicular system has been tested in coal mines. Presently, the major limitation of this system is associated with fatigue failure of the splices in the coaxial line and lack of mobility caused by its 3-wheel design.

Jan 1, 1974

By T. F. Mitchell

During the investigation or the occurrence of manganese deposits in western United States, Bureau of Mines' examining engineers collected samples from four manganese properties in the Death Valley region, California. These were supplemented by samples submitted by owners of two other properties in the same area. Extensive laboratory tests were made to determine the, amenability of the ores to standard ore-dressing concentration methods. A small sample of high-grade oxide manganese ore from the McWhinney property, San Bernardino County, Calif., was submitted by the owner. Although the sample would sinter directly to plus 48 percent manganese grade, it appeared probable that the ore, if mined in quantity, would be lower in grade and would require beneficiation. Therefore, testing was conducted to remove the chief gangue constituent, calcite. The National Resources, Inc., property (also known as the old Owl Hole mine) is in the Owl Hole Springs district, I mile from Owl Hole Springs, San Bernardino County, Calif., near the southwest corner of Death Valley National Monument. The ore deposits occur as small lenses or ,pockets, evidently .replacements in limestone and granite. Laboratory work was done on a representative sample of orb procured by Bureau engineers.

Jan 1, 1949

By L. E. Cardwell

This Bureau of Mines publication contains routine analyses and related source data for 495 natural gas samples from 21 States and three foreign countries. Of this total, 376 samples were collected during calendar year 1968. The remaining 119 analyses are of samples collected during previous years, but releases granting permission to publish the results Here not received until 1968. All samples were collected as a part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917 and in late 1965 was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 576.4 Ten previous publications have presented results of 8,165 gas analyses made by the Bureau of Hines Helium Activity prior to 1968. The first three, Bulletins 486, 576,6 and 617,7 contain analyses and related source data on

Jan 1, 1970

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By Curtis A. Jones

Continuing interest has been shown in developing processes for extracting nickel and cobalt from low-grade domestic deposits of these metals and in improving existing methods. Of special concern is the nickel-recovery installation at Nicaro, Oriente Province, Cuba, operated for the General Services Administration. The Bureau? of Mines felt that a bibliography would help familiarize personnel at various Bureau of Mines stations and General Services Administration contractors with extraction methods both in the United States and in foreign countries. When this task was under way it became apparent that to compile a complete bibliography would require considerable time, so it was decided to limit the first part to the later literature and issue it independently, thus making it available sooner. The present work supplements the first part and extends the coverage to the earliest years of nickel and cobalt metallurgy.

Jan 1, 1959

By L. A. Morley

This report summarizes the work performed on Bureau of Mines Contract J0199106, "Portable Trailing Cables, Splices, and Couplers - Design and Installation Considerations," from May 1, 1979 until December 31, 1981. Splice installations and considerations for the possible use of conductive-rubber shielding in low-voltage trailing cables as well as coupler installations in high-voltage cables were the principal tasks. Flammability measurements on cable components and general testing facilities for mine electrical equipment were secondary tasks. Theoretical and empirical data indicate that conductive rubber with high resistivity values is an unsatisfactory shield design for current-sensing fault detection. Elimination of partial discharge in coupler installations requires meticulous care.

Jan 1, 1982

By Gordon H. Dechman

This report presents the concept, design, and testing of a sonic velocity monitoring system for the early detection of slope failure in open pit mines. The heart of the system is a device for producing reproducible sonic signals in rock. Because changes in the velocity of sound through rock near the top of the pit wall are a measure of extent and rate of fracturing of the rock, velocity histories obtained from periodic, automatic sonic velocity surveys provide positive information about developing slope instability.

Jan 1, 1976

By John H. Johnson

White Pine Mine section designated for exhaust emissions studies. The MTU Mine Air Monitoring Laboratory was used to gather temperature and C02 concentration data at 10 locations. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in stratification in dead end headings. Diesel mine-vehicle tailpipe emissions were monitored in the laboratory by a portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. Diesel pollutant concentration data from the Orchard Valley Mine were analyzed and compared with data collected earlier in the White Pine and Brushy Creek mines. Lognormal frequency distributions and CO2-based concentration ratios and correlations were calculated. In the three mines compared, pollutant concentrations were distributed similarly, and concentrations appear to be controlled to present standards.

Jan 1, 1979

By Charles D. Haynes

Outside air for ventilating coal mines in Alabama varies considerably in both temperature and moisture content during the year. Alternate condensation and evaporation of the moisture on mine roofs may result in stresses detrimental to the strength of mine roof. It is well known that the clays in shales absorb moisture, and many investigations have noted the weakening of shales by absorption of moisture. Parker (1970) concluded that there is an annual cycle of rock deterioration in mine roof rock caused by the annual temperature-humidity cycle at the surface. He further noted that moisture reduces the strength of dry rock by one-half, that moisture added to dry rock can cause failure in compression, and that drying of wet rock causes tensile stress buildups by shrinkage. His recommendations for alleviating the moisture-temperature problem was to seal the rock in critical areas and to control ventilation so that air temperature will be lower than rock temperature. The latter recommendation will avoid condensation on the rock surfaces. Hartmann and Greenwald (1941) published the results of a very comprehensive experimental project to determine the effect of temperature and humidity changes on the behavior of mine roof. Their general conclusions included statements that roof rocks were very sensitive to moisture changes, but had low coefficients of thermal expansion. The coefficients were twice in the direction normal to the bedding plane as compared to the parallel

Jan 1, 1975

By Loren R. Anderson

This Volume documents the use of the Cone Penetrometer data analysis computer programs VERT and HORZ. The programs are interactive in that they prompt the user for input data and allow correction and modification to be made. The programs read data from the results of cone penetrometer soundings and convert the data to values of tan ø. Mean, standard deviation, skew, kurtosis, linear trends and autocorralation are computed by the programs.

Jan 1, 1982

By Carl R. Christiansen

The primary objectives of this project are (1) the determination of manpower demand in primary lead and zinc production for the years 1985 and 2000, and (2) the estimation of the availability of the required manpower for these years. In order to meet the first of these objectives relationships between employee requirements and metal production in the various states were established, The total primary lead and zinc production from United states mines in 1985 and 2000 has been predicted by the U.S. Bureau of Mines. These forecasts and the 1974 figures are as follows: [1974 1985 2000 Lead metal, tons 669,000 700,000 900,000 Zinc metal, tons 494,000 585,000 995,000] Mining By analysis of ore reserve data and industry characteristics, the authors estimated the portion of the primary production which each state would yield in the future years. As manpower requirements are determined by the tons of ore produced and by worker productivity, these figures were determined for each mining state and district by developing relationships between lead and zinc metal production, ore production, ore to recoverable metal ratios, employee productivity, and number of employees required. The number of new employees required annually to compensate for attrition and production growth is provided, also.

Jan 1, 1975