Search Documents

By Jr. Watts, J. L. Ambs, B. K. Cantrell, K. L. Rubow

"The University of Minnesota and the U.S. Bureau of Mines collaborated to develop and field test a personal diesel exhaust aerosol sampler (PDEAS). The PDEAS was field tested in five underground coal mines that use continuous miners and a variety of diesel vehicles, including diesel haulage and utility vehicles. One mine was surveyed a second time, with the haulage vehicles fitted with a low-temperature disposable diesel exhaust filter (DDEF). Aerosol samples were collected with a variety of instruments, including the PDEAS and the microorifice, uniform-deposit impactor (MOUDI). This paper presents the diesel exhaust aerosol (DEA) concentration data collected in these mines and assesses the impact of diesel face-haulage equipment, with and without exhaust filters, on underground mine air quality.The average DEA concentration at the haulageway location for five mines, determined by the PDEAS, was 0.89 mg/m3, with a standard deviation of 0.44 mg/m3 • DEA contributed 52 pct, of the respirable aerosol at the haulageway location. Use of the DDEF at one mine reduced DEA by 95 pct, with a standard deviation of 6 pct, and filter life averaged 10 h. DEA contributed a large proportion of the respirable aerosol concentrations in mines with diesel equipment, and a substantial reduction was achieved with use of a DDEF. INTRODUCTIONDiesel equipment is gaining popularity in underground coal mines. There are an estimated 1,951 units of diesel equipment in 152 underground coal mines compared with 1,100 units in 110 mines 5 years ago (J).5 This increased use is due to the recognition that diesel-powered vehicles are more versatile, which can contribute to increased productivity compared with their electrically powered counterparts. Approximately 33 pct of the diesel vehicles haul coal, 45 pct haul personnel and materials, and- 22 pct perform other duties, such as roof bolting, rock dusting, and road maintenance. Most mines using diesel equipment are located in Kentucky, Utah, Virginia, and Colorado."

Mar 1, 1992

By Oliver Bowles

The National Granite Commission at its annual meeting in Norfolk, Va., in January, 1930, passed a resolution requesting the Bureau of Mines to conduct an economic study of the granite industry. In with this request a preliminary review has been made of trends in the production and uses of block granite.. Some unfavorable conditions were thus brought to light, and certain suggestions regarding a more orderly and consistent growth in the industry are herein discussed. The results of the study are, presented in this report for the earnest consideration of. the industry, and comments are invited, not only on this report but as to future work that might be accomplished by the Bureau of Mines. The authors desire to acknowledge many helpful suggestions and comments from Paul M. Tyler of the Bureau of Mines and from Harris F. Sherman, secretary of the National Building Granite Quarries Association. Miss A. T. Coons of the Bureau of Mines rendered valuable assistance through her wide knowledge of granite statistics. The block granite industry has shown little expansion during recent years. While the value of the annual production has grown from about $14,000,000 in 1904 to nearly $25,000,000 in 1928, the increment in value is caused mainly by mounting prices rather than by increased production. Even granite for memorials shows a very small advance in production volume, although the value has increased from about $3,500,060 in 1904 to more than $11,000,000 in 1928, which is the most consistent growth of any branch of the industry. The value of building granite has fallen for a number of years much below the figure for 1904, and in 1928 was very little in advance of the value attained 24 years previously. The use of granite paving blocks and rubble has shown a gradual decline.

Jan 1, 1931

By C. Q. Cupps

n view of increased interest in secondary recovery of oil in the Cut Bank field, Montana, a review has been made of unpublished data obtained during a 1943-44 study of reservoir oil characteristics in this field. Considerable uncertainty was attached to interpretations of subsurface oil sample analyses from six Cut Bank zone wells, one Lander sand well, and one Moulton sand well, because of adverse sampling conditions and wide range in the data. Much of this uncertainty has been removed by this review which has shown two of the Cut Bank zone samples and the Moulton sand sample to be representative of the reservoir oils. Estimates of original reservoir oil characteristics derived from differential-liberation analyses of these samples show that the oil in the Cut Bank zone was initially saturated at the gas-oil contact pres-sure, 750 psia, and the oil in the Moulton sand was undersaturated with a saturation pressure of only 380 psia. The rest of the samples were indicated to be nonrepresentative of the reservoir oils because of a disproportional vaporization of heavier components of the solution gas. The vaporization of these components is believed to be a cumulative effect of contact of the oil with bypassing, light-gravity gas which had been liberated at higher pressures from solution in oil farther back in the formation, or which had come from the gas cap, rather than from the singular effect of gas evolution caused by excessively low bottom-hole pressures. Change of oil composition caused by the latter was found to conform closely to that occurring during a differential liberation of gas in the laboratory.

Jan 1, 1967

By d&apos, Dennis V. Andrea

The Bureau of Mines and El Paso Mining and Milling Co. conducted a cooperative in situ leaching research program at the Emerald Isle mine near Kingman, Ariz. The objective of this research was to develop in situ leaching methods for 200,000 tons of ore exposed in the pit bottom and also 3,000,000 tons of ore under 200 feet of overburden adjacent to the pit. The research included core drilling for fragmentation analysis, inplace permeability testing, seismic surveys, blasting tests, blast vibration measurements, inplace leaching, and ground water monitoring. A l5,000-ton test area in the pit bottom was blasted and leached inplace for 117 days. This successful test was followed by leaching 100,000 additional tons of unblasted pit bottom ore. Two test blasts, under 205 feet of overburden and extending to 290 feet, were detonated in an area near the open pit. The second blast was detonated because the first blast did not create adequate permeability for leaching. Pit bottom leaching was discontinued and the test area under 200 feet of overburden was not leached because the company terminated operations at the Emerald Isle mine. Based on the research completed, an expanded in situ leaching system was designed, but not implemented, to recover copper from a 1,500,000-ton area at the Emerald Isle mine.

Jan 1, 1977

By H. W. Kilau

The Bureau of Mines tested chromium-bearing waste slags from industrial stainless steel and other chrome alloy operations to determine their chromium leachability characteristics under acid precipitation conditions and to devise measures to prevent any pollution originating from this source. Two critical slag composition factors were found to control the chromium leachability: (1) CaO:Si02 ratio and (2) magnesium content. Above a 2.0 CaO:Si02 ratio, chromium exists in slag as CaO·Cr203, which can be vulnerable to leaching by acid precipitation especially if oxi-dized to CaCr04 when exposed to the environment over an extended period. Maximum chromium leachability from industrial slags occurred when the composition of the slag had about a 2.0 CaO:Si02 ratio. Between a 1.0 and 2.0 CaO:Si02 ratio, in the presence of sufficient magnesium, MgO ·Cr203 was formed, which is very resistant to oxidation and to dissolution by simulated acid precipitation. Addition of magnesium silicates to molten slag to fix the chromium in the MgO·Cr203 form was successful in preventing chromium leaching in simulated acid rain solutions. Experiments showed olivine and waste taconite tailings were suitable for this purpose. Olivine addition to a waste slag having a composition vulnerable to leaching (CaO:Si02 > 2) reduced the chromium leachability more than 80 pct.

Jan 1, 1984

By William H. King

The Mining Division of the Bureau of Mines has been making development and power-requirement studios for the Interior Department Missouri Basin Field. Committee. The studies by the Bureau of Mines have as their purpose, the summarizing of potential future power requirements in the mineral industry within the Missouri Basin, special emphasis being placed on possible expansion of these requirements through construction of new mining enterprises by private capital. In preparing a proposal for the production of phosphoric acid from phosphate rock near Lander, Wyo., it was found that the basic information on the physical and chemical characteristics of the phosphate beds to determine costs of mining and treatment was lacking.

Jan 1, 1949

By R. L. Rough, W. K. Overbey

The Bureau of Mines obtained samples of oil - reservoir rock from wells in Ohio , Pennsylvania , and West Virginia as part of an investigation of the susceptibility of petroleum reservoirs to secondary - recovery techniques . Illustrations and tables showing the geographic and stratigraphic sequence of the cored reservoirs and 40 tables of detailed lithologic descriptions of the reservoirs are presented . Information relevant to geologic surroundings , oilfield history , coring and well logging operations , and reservoir core analyses are referenced throughout the report .

Jun 1, 1970

By Edward W. Parsons

Conventional rock-bolt anchors often fail when installed in weak formations. The purpose of this work was to develop an anchor that would utilize an explosive charge to secure anchorage in any type of rock. Laboratory work to develop a rock-bolt anchored by explosive forming was initiated using rock-bolt models which had a drilled explosive chamber and were composed of various metals. This was followed by the use of several types of seamless tubing which were expanded with a water-coupled explosive capsule. By attaching a length of solid bolt to the anchor tube, a prototype explosive-anchored rock bolt was made. More than 150 laboratory models were expanded during this phase of development, During two field tests in underground mines (A and B) and one in an open- cut mine (C), 87 explosive-anchored bolts, 9 slot-and-wedge bolts, 2 bolts anchored with expanding grout, and 28 expansion-shell bolts consisting of three types of shells were installed and subjected to pull tests. The field tests were run to determine the effects of variables such as the amount and placement of the explosive charge, design changes in the bolt, and the effect on anchorage of different pull-test techniques. The field tests revealed the following: Mine A. The explosive-anchored rock bolt was feasible, but changes were necessary in bolt materials and in some details of bolt design. Mine B. The design and materials of the bolt gave excellent results in hard fractured rock, but no information was obtained concerning variations in the dimensions of the anchor unit or in the explosive charge. Nine C. Varying the explosive charge to produce a beaded surface on the bolt tube and tightening of the anchored bolt before pull-testing were found to increase significantly the anchorage obtained in soft ground.

Jan 1, 1963

By Susan E. Brink

The first step in determining whether Mn can be recovered by in situ leaching is to develop and test a selective lixiviant. Two column leach tests and one core leach test Were conducted by the U.S. Bureau of Mines on Mn oxide ore using aqueous sulfur dioxide (SO2) as the lixiviant. The column tests showed that aqueous S02 could selectively dissolve available Mn oxides from calcite-rich ore in a heap leach system. However, the core test showed that calcite gangue side reactions can have pronounced negative effects on the likelihood of successful in situ leaching of a calcite-rich ore with aqueous S02. Petrographic and geochemical analyses showed that both Mn (IV, III) oxides and calcite were dissolved. The abundance of dissolved Ca caused precipitation of gypsum. Acid consumption by calcite dissolution caused a rise in pH that caused the SO/S species to shift to S032-(sulfIte), which hindered reductive dissolution of Mn oxide. Gypsum precipitation did not affect complete leaching of the rock fragments in the column tests; however, it plugged the natural permeability in the core. Manganese recoveries were high for the column tests and low for the core test.

Jan 1, 2010

By Raghoottma S. Pandurangi, Mohindar S. Seehra, Pedro Bolsait, Bronwyn L. Razzaboni

"Surface IR (infrared) modes of crystalline and fumed (amorphous) silica particles, calcined at temperatures up to 1095°C, have been studied by Fourier transform infrared spectroscopy. The ability of these same particles to lyse cells has been measured by a hemolysis protocol. The untreated crystalline and amorphous materials differ by a factor of 40 in specific surface area, and the intensity per unit mass of the sharp surface silanol band near 3745 cm-1 in the amorphous material is an order of magnitude larger than in the crystalline material. A similar difference is observed in the lysing potential of the two materials. The intensity of the silanol band increases after calcination for both materials, reaching peak values near 500°C, followed by a dramatic drop at higher calcination temperatures, and reaching negligible values for materials calcined near 1100°C. The lysing potential data follow essentially the same pattern for both crystalline and fumed silica. These results are consistent with the hypothesis that the surface silanol groups are involved in cell lysis. Further experiments are suggested to evaluate the relationship between the surface structure of ailica particles and their potential cytotoxicity. IntroductionThe characterization of the surface structure of various allotropic forms of silica is of interest because the cytotoxicity of silica particles of respirable size has been commonly related to the chemical interaction of functional groups on the surface of such particles with the lipoproteins contained in cell membranes (1-3). It has been found that the cytotoxic potential of silica particles varies greatly with their crystalline structure (4,5), particle size (6-8), surface composition (9), and molecular surface configuration (1,10). Studies of the infrared (IR) modes of various forms of silica have been reported by a number of researchers (3 ,11-19). Several books and reviews (20-24) have dealt with the identification of functional groups on silica surfaces and the effect of heat treatment on the surface structure. The nature of the surface is said to be critical in determining the biological activity of silica dusts (3).Fourier transform infrared (FTIR) spectroscopy is a highly sensitive ·technique for identifying IR surface modes of tine particulates, and it was deemed of interest to examine the surface structure and its relation to lysing potential of two widely different types of respirable silica dust. The lysing potential of respirable dust particles has been considered a first-level test for potential cytotoxicity."

Jan 1, 1990

By J. L. Reuss

The Bureau of Mines derived information on the softening characteristics of both unfired and indurated iron ore pellets as measured by hot compression strength in a laboratory study. A surprisingly high hot strength (240 1b per ½ -inch spheroid) was developed by unfired magnetite pellets near 900° C; lesser maxima were developed by pellets made from hematite and specularite concentrates near 1,000° C. Those from goethite remained weak throughout the pre induration heating. Fully indurated commercial pellets retain a high resistance to softening when heated in air. On the contrary, in a hot reduing atmosphere their high cold crushing strength dissipates rapidly. At 1,000° C, for example, the average compression strength of seven different commercial pellets was 110 lb; at 1,100° C, the hot strength was only 60 lb. After a rather sharp initial drop, the loss of strength with increase of temperature was gradual. There was no sudden collapse, nor any significant difference, in behavior of commercial pellets whether made from magnetite or hematite concentrates.

Jan 1, 1968

By B. D. Nash

The object of this research was to investigate the technical feasibility of preparing chromium metal by the thermal decomposition of bisbenzene chromium. Bisbenzene chromium, a pi-bonded sandwich type organometallic compound, was thermally decomposed under reduced pressure to form a metal plate on a heated substrate. Metal recovery was close to 100 percent of theoretical, with deposition rates up to 20.8 mg/hr/cm2. Metal purity was dependent not only upon the purity of the starting material, but also upon the sublimation rate of bisbenzene chromium. Total detectable metallic impurities ranged from a low of 18 ppm to several hundred ppm. In general, metallic impurities were less than 100 ppm. Carbon, the major nonmetallic impurity, ranged from less than 0.3 percent to more than 10 percent. The carbon contamination is most likely a result of the decomposition of the organic portion of bisbenzene chromium. An unusual property of some of the deposits was their outstanding corrosion resistance. Unlike pure electrolytic chromium, which dissolves readily, these deposits were insoluble in hot mineral acids.

Jan 1, 1968

By L. K. Weaver

Bureau of Mines investigated the progressive impact that petroleum (crude oil and condensate) operations in the Gulf of Mexico have had on onshore operations and the expected effect of increasing activities in this area on future petroleum supplies from domestic sources. The data analyzed include capital expenditures, number of wells drilled, success ratio for exploratory wells, daily production per completion, annual producing rates, and oil reserves. The report compares offshore and onshore data and ascertains trends in petroleum industry operations. Observed data and trends indicate that in the near future Gulf of Mexico development and production will continue to increase relative to total U.S. petroleum activity. By 1975 annual oil and condensate production from the Gulf of Mexico is expected to be in the range of 750 million bbl to 1,150 million bbl, and account for approximately 20 to 30 pct of the estimated total domestic production.

Jan 1, 1969

By A. Galaitsis

This report summarizes part of the work performed under the USBM Contract No H0155113, "Noise Abatement of Continuous Mining Machines." It describes the noise source diagnosis of a Jeffrey 120M conveyor and the evaluation of several treatments all conducted in a test facility aboveground. The conveyor noise at the operator's position was gradually reduced from 101.5 to 93 dBA using damping, vibration isolation, sound barriers and smoother discontinuities. The underground performance of the selected treatments will be addressed in Volume II of the report.

Jan 1, 1979

By A. B. Needham

This paper, which describes mining practices at a mine in the Cave- in-Rock, Illinois, fluorspar district, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. Ore deposits in the southern Illinois-western Kentucky fluorspar dis- trict are of two general types (1) the flat-bedded, lenticular replacement and (2) the relatively narrow, rather steeply dipping fault or fissure filling. This paper describes production methods used and results obtained in mining one of the bedded lenticular ore bodies that are prevalent in the northeast portion of the district near Cave-in-Rock.

Aug 1, 1949

By S. L. May

The Bureau of Mines has developed several methods for extracting tantalum and columbium (niobium) and the rare-earth compounds from ores and concentrates. A cooperative agreement was made by the Bureau with Porter Bros. Corporation of Idaho to process 200 pounds of its euxenite concentrate by methods that had been developed at the Albany, Oreg., Metallurgy Research Center. The euxenite concentrate was processed to extract and purify the valuable metals by chlorination, solvent extraction, and hydrometallurgical techniques. Chlorination was used to convert the valuable constituents into chlorides and to partly separate them. Solvent extraction techniques were used to separate the tantalum from the columbium. The rare-earth and uranium compounds were purified by hydrometallurgical methods.

Jan 1, 1959

By SUMNER S. SMITH

Mine inspection in Alaska by the Federal mine inspector was somewhat handicapped during 1915,the inspector having to spend a large part of the summer and fall in examining the Matanuska coal field in connection with the designation of the Government reservations and the leasing units in that field. However, in addition to>this work, the mines in southeastern and southwestern Alaska were inspected by both Federal and Territorial inspectors, a considerable number of men near the Federal inspector's officeat Juneau were trained in first aid to the injured and in the use of mine rescue apparatus, the mines of the interior and of Seward Peninsula were inspected by the Territorial inspector, and a suit was brought in the name of the Territorial inspector for the nonreporting of serious accidents under the Territorial inspection law. The work of the Federal inspector was handicapped also by a lack of field assistants. This condition is likely to be serious, as preparations have been made for opening the Matanuska, Bering River, and Nenana coal fields, and a number of permits granting the free use of 10-acre tracts in other fields throughout the Territory have been issued. The need of a comprehensive inspection law and experienced engineers to safeguard the opening of coal mines by operators who are not familiar with coal mining and are using inexperienced help is obvious.

Jan 1, 1917

By Deborah A. Kramer

An economic and technical evaluation of a proposed process to recover alumina by leaching calcined kaolinitic clay with sulfurous acid is presented in this Bureau of Mines report. After the insoluble portion of the clay has been removed by leaching, monobasic aluminum sulfite is precipitated from the pregnant leach solution by partial hydrothermal decomposition. Further heating completes the decomposition to an impure alumina hydrate. This intermediate is purified in a modified Bayer process, which includes dissolving the alumina hydrate in a caustic solution at high temperature and pressure, then decreasing the temperature and pressure to precipitate alumina trihydrate. Calcining the trihydrate produces the alumina product. A cost estimate was prepared for a plant producing 1,000 tons of alumina per day, 350 d/yr. The estimated operating cost is approximately $475 per ton of alumina. This is substantially higher than a comparable estimated operating cost for the Bayer process of $250 per ton of alumina. The proposed process does not appear economically attractive, even as a method to modify a current Bayer processing plant to use a kaolinitic clay feed. High capital costs and high energy requirements make the process prohibitively expensive.

Jan 1, 1983

By K. K. Kelley

Despite the wide interest in titanium and its compounds, no heat and free-energy-of-formation values for titanates (that is, compounds formed from titania and other metal oxides) have been available heretofore except for ilmenite (FeTi03). Such data are needed for understanding and developing processes for producing titania and titanium tetrachloride from ores (and possibly slags) and in connection with ceramic usage of titania. This paper reports experimental measurements of the heats of formation at ordinary temperature of 11 titanates-ilmenite, perovskite, barium metatinate, strontium metatitanate, barium-strontium metatitanate, barium orthotitanate, strontium orthotitanate, barium-strontium othotitanate, geikielite, magnesium-titanium spinel, and magnesium dititanate. The experimental method was solution calorimetry. The solution calorimeter was operated at 73.7°C. and used a strong hydrofluoric-hydrochloric acid mixture as the calorimetric fluid and reaction medium.

Jan 1, 1954

By H. W. Kilau

The U.S. Bureau of Mines is evaluating water spray additives for the purpose of improving respirable dust control during coal mining operations, with particular emphasis on the longwall shearer. Recent field tests of surfactant-polymer reagents at two production longwall operations have shown favorable respirable dust reductions compared with water sprays containing no additive. Gravimetric dust samples obtained by a technician downwind of the shearer while following or preceding the machine showed dust reductions in the range of about 40% to 60% for some of the reagent formulations compared with using water alone. Three polymers were tested: two polyethylene oxide compounds of different molecular weight and hydroxypropyl methylcellulose (HPMC). All were effective for dust reduction, and two were cost effective when used in combination with sodium di(2-ethylhexyl) sulfosuccinate surfactant. How-ever, the use of these reagents requires the longwall operator to be more aware of headgate dust control. Experimental evidence indicates that dust captured by reagent-treated sprays at the shearer can be reemitted in the headgate area if stagcloader-crusher sprays and other dust controls are inadequate.

Jan 1, 2010