Search Documents

By Jack G. Croeni

The Bureau of Mines developed a method to extrude low-density tungsten powder billets into rods and sheet bar with high-energy-rate forming equipment. Billets were compacted and sintered in an atmosphere of hydrogen to obtain a density of approximately 60 percent. Extrusion was conducted at reduction ratios of 6.25 to 1 and 9 to 1 at 1,800° C to prod e high-density, sound material. Yield strengths obtained were higher than those of material produced by conventional powder-metallurgy techniques, but ductility was lower at high temperatures.

Jan 1, 1966

By Oliver Bowles

The manufacture of lime is one of the oldest industries. Plants are distributed widely and furnish an essential raw material for numerous industries. The use of lime by the building trades, in agriculture, and in hundreds of manufacturing and chemical processes has created demands for a large production and has necessitated exhaustive research on methods of manufacture and uses. The bibliography of lime is an extensive one, but for the most part each publication has dealt with only certain operations. The purpose of this paper is to present a general picture of the industry as a whole. The abundant literature has been abstracted and quoted freely, and the National Lime Association has rendered valuable assistance in furnishing data for certain sections. Publications containing more detailed information on the various branches of the industry are referred to in the footnotes and in the bibliography.

Jan 1, 1936

By Robert M. Becker

Particle mixtures were sampled in the laboratory, using ordinary sampling procedures, to determine whether or not the compound-multinomial probability distribution and other developments of part 2 agreed with experimental results. The objective was accomplished by the Bureau of Mines by comparing the moments and moment relationships of the appropriate probability models with their corresponding experimental values over a fairly wide range. The overall agreement between the corresponding theoretical and experimental values is both good and complete. The results demonstrate that sampling to a constant amount, such as weight, of items per sample is not the same, in general, as sampling to some constant number of items per sample. The results seem to confirm all the developments of part 2 and the application of the compound-multinomial function to bulk sampling.

Jan 1, 1965

By P. D. Tracy, M. W. Von Bernewitz

"IntroductionA study of 256 coal-mine explosions, which occurred during the period 1909-1924 killed 4113 men and injured 570 others, reveals the fact that there are the critical times of day when explosions are most likely to occur, and when corresponding care should be exercised to guard against disaster. Of these 256 explosions, 83 straight as explosions, 89 were straight coal-dust explosions, and 81 were mixed gas and dust explosions, while three were undetermined.It has been determined from the times given in these reports (in several cases no times were given,that the critical period in the morning ranges between 6 and 9 o'clock when 83 explosions took place with a peal. at 7;30 o'clock. Of these 55 were straight gas explosions, the remainder being either coal dust or mixed gas and coal dust explosions. The critical period in the afternoon or early ranges between 3 and 7 o'clock, when 113 explosions took place, with a peak at 6 o'clock. Of these, 87 wore straight coal-dust explosions the remainder being neither gas or mixed gas and coal-dust explosions. Between these morning and evening periods is one which might be called the noon period - that is, from 11m to 7. p. m. - when 26 explosions occurred while some of these were normal type of explosions - that is, as to causes - others were of unusual cause and character, and. are discussed later. A number of explosions (29 in all) took place during mid-afternoon, late at night, and early in the morning - that is, after midnight."

Sep 1, 1924

By Robert Bottge

When a company develops a mineral property in a remote area of Alaska, it must consider how best to house its personnel. This Bureau of Mines report examines the economics of two options: company towns and company camps. The price required to maintain a 15% discounted-cash-flow rate of return (DCFROR) was derived for hypothetical 1,000-st/d cut-and-fill mines and 50,000-st/d open-pit mines located in three different regions of the State, One set of hypothetical mines utilizes a townsite; the other utilizes a relatively new concept, a fly-in camp or commuting operation, in which two shifts of employees operate the mine and all associated facilities for 1 week before being replaced by a second crew. The study shows that operating costs were higher for mines employing the commuting option than for mines having a company town because of the additional wages paid for overtime hours; however, the price required to obtain a 15% DCFROR for the single-product copper concentrate, f.0.b. the mill site, was significantly lower owing to the lower investment costs for the camp-type operation. The economic advantage for those mines utilizing the camp increases from south to north and from the coast toward the interior.

Jan 1, 1986

By Richard D. Mehring

A refined ad improved self-sealing brattice for use in coal mine rescue and recovery operations for directing the flow of air has been developed and tested by Goodyear Aerospace Corporation for the U.S. Bureau of Mines. The brattice is made from a lightweight, low cost material that meets MSHA flammability requirements. The units can be erected using pins, spade or lightweight extensible poles. Tests here conducted to determine leakage rate from minimal to a maximum of 1.5" H20. The ability to handle reverse flows was demonstrated and a non-flammable foam was used as an auxiliary sealing agent.

Jan 1, 1978

By Frank E. Federspiel

In 1992, the Bureau of Mines conducted a mineral resource investigation of the 78,000-acre Garns Mountain study area in southeastern Idaho. The area had been proposed for Wilderness. It is underlain by Paleozoic to Mesozoic-age sedimentary rocks about 11,000 feet thick. Rocks have been faulted, offset, and folded as part of the northerly-trending Idaho-Wyoming Overthrust Belt. Study area mineral occurrences are: phosphate in the Permian Phosphoria Formation; coal in the Cretaceous Frontier end Bear River Formations; and uranium in carbonaceous and phosphate-bearing shales and coal of these formations. Four zones of phosphate are estimated to contain about 528 mitt ion tons of rock with over 10% P205; samples of phosphate-rich rock also contained as much as 3950 ppm chromium, 3280 ppm vanadium, 23 ppm gallium, and 5540 ppm zinc. Fragments of poor-quality coal and carbonaceous shale were found in the area; coal was mined near the northeast border. Uranium content up to 0.016% U3O8 is in carbon-rich shales. Oil and gas were drilled for, with minimal success, in folded sedimentary rocks (frontier and Nugget Sandstone) in the Horseshoe anticline, near the east border. Examined workings included 12 dozer cuts, 4 trenches, 2 prospect pits, and 2 caved adits. No production is known, and no leases or claims are held for the area.

Jan 1, 1992

By A. J. Farstad

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped mines in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light-weight and inexpensive.

Jan 1, 1979

By K. E. Tame

An alkaline leaching procedure for recovering uranium from a submarginal 0.1 percent Ug Og calcareous carnotite ore from the Shiprock , N. Mex . , area was investigated . A recovery of 72 percent of the uranium was attained in a preliminary test embodying the commonly accepted practice of ( 1 ) alkaline leaching at 90° C , ( 2 ) multiple stage filtration and washing for recovery of a clear pregnant solution , and ( 3 ) caustic precipitation of uranium as sodium diuranate , with recycle of the barren solution to the leaching and washing circuits . Ion exchange resins were used in a second , less orthodox test that comprised ( 1 ) sodium carbonate leaching of minus 10- mesh ore at 90 ° C to dissolve the uranium , ( 2 ) filtration to recover the leaching reagent for reuse , (3 ) recovery of the uranium- bearing solution in the filter cake as a pregnant slime slurry by repulping of the filter cake followed by a sand- slime separation and countercurrent decantation (CCD ) washing for rejection of the sand fraction , (4 ) recovery of the dissolved uranium from the pregnant slime slurry by resin- in- pulp (RIP ) , ( 5 ) elution of the uranium from the resin with a solution of ammonium chloride acidified with hydrochloric acid , and (6 ) precipitation of the uranium with ammonia gas . About 83 percent of the uranium was extracted from the ore and 95.5 percent of the dissolved uranium recovered by ion exchange . Improved laboratory results were obtained using the RIP process , but larger scale tests would be necessary for economic evaluation of the two processes .

Jan 1, 1964

By T. E. Gray

This report describes the preparation characteristics of the signifi¬cant coalbeds in Preston County, W. Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 2 million tons of coal was produced in Preston County, W. Va. in 190, none of which was cleaned mechanically. Estimates as of January 1, 1959, indicate that more than 3 billion tons of coal remained in the county in beds 12 inches or more thick. The Bakerstown, Mahoning, Upper Freeport, and Upper Kittanning beds were selected by the Bureau of Mines for study based on current production and estimated minable reserves. Sample locations were selected after study of the literature, conferences with mining engineers and mining company offi¬cials in the field, and examination of available sites. Four samples were collected from the Bakerstown and Upper Freeport beds and one each from the Mahoning and Upper Kittanning beds.

Jan 1, 1961

By Martin H. Stanczyk

The Bureau of Mines studied continuous closed-circuit attrition grinding of a coarse commercial filler-grade kaolin to produce paper-coating-grade clay having a particle size analysis of at least 70 percent minus 2-micron equivalent spherical diameter (esd). The coarse clay, containing about 12 percent minus 2-micron-esd material, was ground in a Bureau-developed 10-inch-diameter attrition grinder in closed circuit with a 5-foot-diameter bowl classifier. In the best test, a finished product containing 82.7 percent minus 2-micron-esd material was obtained when grinding 20 pounds of raw clay per hour at percent solids with a 100-percent circulating load. Energy consumption was about 341 kilowatt-hours per ton of clay feed, or 487 kilowatt-hours per ton of minus 2-micron-esd material produced. Closed-circuit grinding gave some-what greater particle size reduction and lower energy consumption than either batch or continuous open-circuit grinding.

Jan 1, 1965

By Richard F. Hewlett

This report describes how a limited number of preliminary exploration drill-hole assays from a mineral deposit can be used to design grid spacing that is both economic and efficient for subsequent evaluation drilling of that deposit. Relationships between desired precision of the estimate of grade of ore and drilling cost are used to determine the economic drill-hole spacing. The statistical concept of precision in estimating grade of ore is used to determine the efficient drill-hole spacing. Assay data from approximately 50 known copper deposits were studied, and the relationships of the statistical parameters of these deposits were computed. Drilling requirements for various precisions of the estimates of grade of ore were computed for some of these known deposits to serve as guides for drilling future copper deposits. The effect of various geologic factors on the trend in grade of ore and, therefore, on the drilling requirements is shown for certain deposits.

Jan 1, 1965

By R. E. Heithecker, D. B. Taliaferro

"INTRODUCTION Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Gore specimens first were obtained mainly for the geologic information they revealed; now they are analyzed to determine many of the physical characteristics and conditions of the subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, ""connate"" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and avail¬ability of oil and as within a reservoir and in devising efficient means for their withdrawal.Examination of bottom-hole samples of oil gives valuable information concerning the amount of gas in solution in the oil within the reservoir and the resultant shrinkage of the oil when the gas is released. Producing characteristics of reservoirs nay be determined by means of subsurface pressure and temperature gages and measurements male at the wellhead; however, unless reliable core analyses are available, these data have only limited use in any quantitative study of reserves. In such a study the quantity of oil, gas, and water contained in a unit volume of the reservoir formation is extremely important. Although reliable methods of analyzing cores have been developed and the data thus obtained are valuable, their applications become more limited or reservoirs at higher temperatures and pressures are discovered. This condition results almost entirely from the fact that in recovering a core from a formation of high pressure and temperature by present methods a large part of the fluid content of the core is lost or contaminated to an unknown extent. For a number of years most petroleum engineers have held that if this loss and contamination of the fluid content of a core were eliminated, the value of core analyses would be increased greatly."

Nov 1, 1939

By P. L. Woolf

Three trials with oxygen-enriched unheated blast air are described. The trials were conducted in the Bureau of Mines experimental blast furnace located in Bruceton, PA. The first trial utilized moisture addition to the oxygenated blast. The second and third trial were conducted with natural gas injection. The test was basically a feasibility study and in that regard the practice was demonstrated to be feasible and also have possible advantages over hot blast operation. The testwork was conducted in 1964 and 1965 as part of a continuing study of iron making technology in cooperation with several North American Steel Companies.

Jan 1, 1985

By R. Pakalnis, Richard P. Curtin, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control to monitor rock mass loads at various field sites (FMC Granger, Getchell, Meikle, SSX, K-2, and Stillwater). Axial and shear loads were determined by strain gauges to levels of instrument accuracy of ±5 N or ±5 microstrain as these loads were transferred to the instrumented cable bolts. These gauges were 12.5 mm long and embedded into are manufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. By monitoring load on and displacement of the rock mass, more effective ground support can be selected and installed, which will lead to safer working conditions for miners.

By B. C. Burgess

This paper, describing the milling practices at the Minpro plant of the Tennessee Mineral Products Corporation, Spruce Pine, N. C., is the first of a series being prepared by the U.S. Bureau of Mines on feldspar milling methods and costs in the various feldspar producing areas in the United States. It describes not only the latest practices in feldspar grinding but includes studies of the cost of producing ground feldspar. These cost studies, obviously of interest to every consumer and purchaser of feldspar and to all feldspar grinders, are also of value to the small operator, who is generally prone to understimate his real costs. It describes the latest practices in feldspar milling and includes detailed costs of grinding. The cost tabulations presented show operating expenditures only and not total production costs. Details of costs are given only to the extent that they are essential to the technical discussion and study of the methods employed. A description of the recently installed milling unit for the preparation of granular glasspar by graded crushing, and magnetic separation is of particular interest. It illustrates how highly specialized feldspar milling has become, and to what an extent grinders are going to supply consumers with the products best suited for their particular needs.

Jan 1, 1931

By J. J. Shields

The Bureau of Mines observed two different types of longwall mining; the advancing longwall method and the retreating longwall method at seven bituminous coal mines located in five of the coal producing states. In two mines using the advancing face method, the coal faces were abandoned because of roof failures and poor production. In the other five mines using the retreating method, roof control was good as was production. The success of longwall mining depends on good roof control and good production. The use of self-advancing hydraulic roof supports, such as Westfalia, Dowty, and Wanheim props along with Westfalia coal planers and the Anderton and Eickhoff shearer-loaders have been a factor in recent successes.

Jan 1, 1967

By P. F. Sands

This U.S. Bureau of Mines report reviews the state of the art in blind pneumatic stowing of backfill in voids in abandoned coal mines. It contains a short history of the development of pneumatic equipment in mining and four recent case histories of blind pneumatic stowing. Limitations of pneumatic stowing in terms of equipment wear, costs, backfill material, and methodology are discussed, and some new procedures and designs are reviewed. A bibliography covering pneumatics in mining is included also. This report provides background for the preparation of a Bureau test program in which the variables affecting the efficiency of pneumatic backfilling will be studied using a full-scale surface test facility.

Jan 1, 1990

By E. D. Gardner

The mine of the Eureka Standard Consolidated dining Co. is at Dividend, Utah, in the Tintic mining district. It is operated under the same management and controlled by the Antic Standard Mining Co.; the two properties adjoin each other. The Eureka Standard is worked through a vertical shaft; the ore is mined by a stringer-set-and-fill method. One hundred and thirty men were employed in April 1933. The normal daily tonnage is 100 tons; the ore is shipped to the smelter at Garfield, Utah.

Jan 1, 1935

By R. V. Ramani, J. Qin

"During the mining process, the insitu material is broken into different size ranges, from very, large pieces to very fine particles. Some of the fine particles become airborne. In underground coal mining, airborne respirable. dust is associated with health and safety of the miners: The amount and size distributions of airborne dust are important parameters to effective dust control measures. The design of underground mine experiments, including sampling procedures and sample analyses methods to determine these parameters are presented in this paper.. A total of fifteen continuous miner cuts were sampled. The amount of dust generated during the cutting process and the relationship between total and respirable airborne dust concentrations and amounts are examined.The amount of respirable dust airborne is on the average only. 0.016% of the respirable dust generated. On the average, 61% of the total .airborne dust measured is in the respirable size range. The amount of respirable airborne' is on the average 36% of the respirable size fraction in the total airborne dust. For equal proportion of rock and coal material cut, rock contributes about twice as much fines (<0.22 mm) as coal. Additional fundamental research is necessary to further the understanding of 'the airborne propensity of respirable dusts in mine atmospheres.INTRODUCTIONMining is a sequential process of breaking, gathering, loading, and transporting the in-situ .materials.' In underground coal mines, duet in both the non-respirable and respirable size ranges is generated and entrained in every phase of the process. Even though large amounts of dust particles' adhere to run-of-mine coals, part of the dust generated becomes airborne (Cheng and Zukovich, 1973). Studies have shown that bit type affects the amount of dust generated'(Evans and Pomeroy, 1966; Kurth et al., 1975; Roepke et al., 1976; Stecklein et al., 1982; and Khair and 'Reddy, 1986). Deep cutting can reduce airborne dust generation (Black and Schmidt, 1977 arid, Black et 1978). Mechanical properties of. coal seams are also important factors in dust generation. Laboratory studies have shown that Hardgrove Grindability Index (HGI) of the coal has a relationship with the amount of respirable. dust generated (Beafi and Ramani, 1979; Moore and Bise, 1984; and Moore, 1986). However, these relationships have not yet been validated with' data from the mines. The amount of dust airborne depends on a number of factors. Suppression of the airborne propensity of dust by water sprays is'widely practiced and is very effective. Water flow rate; pressure and configuration of water sprays have been identified as major factors affecting dust capture by sprays (Courtney and Cheng, 1977; Courtney et al., 1978; and Kissell et al., 1979). Ventilation is a very important means of controlling the dust level at the coal face (Jayaraman, 1977). According to a National Academy of Sciences study (1980), the mechanism of dust generation and the process by which the generated dust becomes airborne are complex and not yet completely understood coal seams are also important factors in dust generation. Laboratory studies have shown that Hardgrove Grindability Index (HGI) of the coal has a relationship with the amount of respirable dust generated (Beafi and Ramani, 1979; Moore and Bise, 1984; and Moore, 1986). However, these relationships have not yet been validated with data from the mines. The amount of dust airborne depends on a number of factors. Suppression of the airborne propensity of dust by water sprays is widely practiced and is very effective. Water flow rate; pressure and configuration of water sprays have been identified as major factors affecting dust capture by sprays (Courtney and Cheng, 1977; Courtney et al., 1978; and Kissell et al., 1979). Ventilation is a very important means of controlling the dust level at the coal face (Jayaraman, 1977). According to a National Academy of Sciences study (1980), the mechanism"

Jan 1, 1989