Search Documents

By Stephen A. Hare, O&apos

Powder metallurgy processing of commercial Raney nickel powders was examined. The typical angular particle shape, in conjuction with aluminum present in a eutectic phase, facilitated interlocking leading to excellent green strength after compaction. Density and porosity as influenced by the compacting pressure were studied over the range of 37.5 to 207 meganewton per square meter (MN/m2). Sintering in an inert atmosphere from 575° to 850° C caused a volume increase which is attributed to a solid state reaction between Al and Ni2Al3 phases. The reaction is 3Al + Ni2Al3 ? 2NiA13. A thermal pretreatment of 70 hours at 700° C was required to prevent this reaction from occurring during sintering. Density and porosity as a function of compacting pressure and sintering temperature were determined after a thermal pretreatment of the powder.

Jan 1, 1976

By H. C. Carpenter

This literature study of methods for desulfurizing residual fuel oil was conducted by the Bureau of Mines at the request of the Department of Health, Education, and Welfare. The sulfur compounds in residual fuels are believed to consist chiefly of condensed thiophenes and other polycyclic sulfur compounds. Hydrodesulfurization appears to be the most promising method for desulfurizing these oils and is the only method applicable to all types of sulfur compounds. There are indications in the literature that hydrodesulfurization without hydrocracking of residual oils may require higher pressures than used in present desulfurization processes, but no cost data and little experimental data are available on the higher pressure operation. Literature proposals for hydrogenating residual oils and heavy crude oils are exclusively for hydrocracking the oils to lower boiling products with accompanying partial desulfurization of the residual fuel fraction. Costs of the hydrocracking operations appear the closest available to probable costs of hydrodesulfurizing the oils, and have been reported (in 1955 to 1957) as $500 to $840 investment cost per daily barrel of capacity, with total operating costs of 70 cents to $1.10 per barrel.

Jan 1, 1963

By H. C. Carpenter

This literature study of methods for desulfurizing residual fuel oil was conducted by the Bureau of Mines at the request of the Department of Health, Education, and Welfare. The sulfur compounds in residual fuels are believed to consist chiefly of condensed thiophenes and other polycyclic sulfur compounds. Hydrodesulfurization appears to be the most promising method for desulfurizing these oils and is the only method applicable to all types of sulfur compounds. There are indications in the literature that hydrodesulfurization without hydrocracking of residual oils may require higher pressures than used in present desulfurization processes, but no cost data and little experimental data are available on the higher pressure operation. Literature proposals for hydrogenating residual oils and heavy crude oils are exclusively for hydrocracking the oils to lower boiling products with accompanying partial desulfurization of the residual fuel fraction. Costs of the hydrocracking operations appear the closest available to probable costs of hydrodesulfurizing the oils, and have been reported (in 1955 to 1957) as $500 to $840 investment cost per daily barrel of capacity, with total operating costs of 70 cents to $1.10 per barrel.

Jan 1, 1963

By R. Barany

The heats of formation of seven substances were determined by solution calorimetry. At 298.15° K, the heat of formation of lithium sulfate from lithium, rhombic sulfur, and oxygen was -343.1 ± 0.7 kcal/mole, and the heat of formation of lithium sulfate monohydrate from lithium, rhombic sulfur, oxy-gen, and hydrogen was -414.3 ± 0.7 kcal/mo1e. For the silicates, the heats of formation at 298.15° K from the elements were kaliophilite, -503.8 ± 0.5 kcal/mole; leucite, -721.6 ± 0,8 kcal/mole; eucryptite, -505,2 ± 0.6 kcal/mole; alpha-spodumene, -727.9 ± 0.9 kcal/mole; and beta-spodumene, -721.1 ± 0.9 kcal/mole. The corresponding heats of formation at 298.15° K from the constituent oxides were kaliophilite, -42.7 ± 1.1 kca1/mole; leucite, -42.8 ± 1.1 kcal/mole; eucryptite, -16.1 ± 0.7 kcal/mole; alpha-spodumene, -21.0 ± 0.7 kcal/mo1e; and beta-spodumene, -14.3 ± 0.7 kcal/mo1e.

Jan 1, 1966

By Charles L. Kimbell

In overview, 1988 appeared to be the best year for the world's mineral industry since 1980, although the all-important petroleum component suffered severely from low prices. With this notable exception, the traditional statistical measures of mineral industry performance, namely production, trade, and consumption, reflected growth in most elements of the world mineral industry from crude material extraction through the gamut of downstream processing. Moreover, the growth was reasonably well distributed geographically, with many countries sharing in the substantial upturn in activity. World crude mineral output value was estimated at over $1,272 billion in current dollars ($1,090 billion in constant 1983 dollars). The value added by the processing component of the mineral industry raised the total value of the industry's output to an estimated $3,057 billion in current dollars ($2,620 billion in constant 1983 dollars). Less easily assessed was the value of mineral commodities moving in 1988's international world trade, particularly because of the declines in world crude oil and refinery product prices. It remained to be seen if increased volume and value in nonfuel mineral and coal exports, coupled with an increase in the volume of oil exports, would be adequate to offset the drop in oil prices. Whether or not the value of world mineral commodity trade topped the 1987 level of over $498 billion, an increase in the volume of mineral commodity trade was almost assured. Similarly, although comprehensive statistics were not avail-able on consumption of all mineral commodities in all countries, available data on selected major commodities in selected major countries suggested that not only had output of most mineral commodities advanced, but so too had consumption levels for most commodities.

Jan 1, 1990

By John C. Edwards

Standard smoldering and flaming combustion tests using smaIl coal samples have been developed by the U.S. Bureau of Mines as a method to evaluate the response of a smoke detector. The tests are con-ducted using a standard smoke box designed and constructed according to Underwriters Laboratories. The tests provide a standard, easily reproducible smoke characteristic for smoldering and flaming coal combustion, based upon a comparison of the smoke optical density and the response of a standard ionization chamber to the smoke. With these standard tests, the range of threshold limits for the response of a smoke detector and the detector's reliability can be evaluated for nearly identical smoke visibility and smoke physical characteristics. The detector's threshold response limits and reliability need to be well defined prior to the instrument's use as part of a mine fire warning system for improved mine safety.

Jan 1, 2010

By Stephen P. Holt

In the fall of 1946 and spring of 1947 the Bureau of Mines put down five inclined diamond-drill holes totaling about 3,100 feet of bore to test for the possible eastward extension of the Royal Princess ore deposit in Jo Daviess County, Ill. Attention of the .Bureau was first directed to this property by the Illinois State Geological Survey. The history of production of the Royal. Princess mine and reports as to the size and nature of the deposit were considered justification for investigating the trend of the mineralization. This report describes the work done by the Bureau of Mines and presents the data obtained.

Jan 1, 1948

By George W. Hezzelwood

This paper describing the minim, methods at the mine of the Consolidated Cortez Silver Mines, Cortez, Nevada, is one of a series of similar papers being prepared by the Bureau of Mines on mining practices and costs in the various mining districts of the United States. The Cortez district is situated on the southwest slope of Mt. Tenabo of the Cortez Range, near the middle of the boundary line between Eureka and Lander Counties (fig. 1). The camp of Cortez is 36 miles south of Beowawe, the nearest station on the Southern Pacific and Western Pacific Railroads. Mt. Tenabo, which is the highest summit of the south end of the Cortez mange, has an elevation of 9,240 feet; Cortez is about 6,280 feet above sea level. The Consolidated Cortez Silver Mines is the only company operating in the district at the present time and employs about 60 men. The daily production of l25 tons of silver-lead ore is concentrated in the company's mill of 150 tons capacity. The concentrate is hauled to Beowawe by automobile trucks for shipment to a reduction plant in Salt Lake Valley, Utah.

Jan 1, 1930

By Leonard Obert

The investigation reported herein is concerned with the generation and propagation of the strain wave produced in rock by the detonation of a high-velocity explosive. This report is the second of a series that will deal with this and related problems. The rock type in which these experiments were carried out was greenstone. Subsequent reports will discuss similar investigations in other rock types. Specifically, the problem under study is concerned with how certain characteristics of the strain wave, such as the maximum compressive and tensile strain, the maximum time rate of change of strain, the frequency components present in the pulse, the duration of the pulse, and other measurable characteristics, vary with the size of the charge and the distance from the detonation point to the point of measurement. . Other investigators have studied certain aspects of the generation and propagation problem in rock. However, in these studies the travel distances from the detonation to measurement point were comparatively long and the frequency components in the explosive wave were usually under 100 c.p.s. In this study the detonation to measurement distance covered. the range from 2 to 54 feet, and the strain gages and recording equipment employed in the instrumentation of the problem had a frequency response range from 200 to 10,000 c.p.s.

Jan 1, 1950

By Jennifer Riefenberg

The U.S. Bureau of Mines has long recognized the hazards associated with rock burst activity in underground mines. Concern over lost lives and resources prompted this study to further characterize rock burst occurrence as related to microseismicity and mining. A period of over 1,079 days of mining with 101 bursts, where microseismicity rates and blasting were recorded, was used in this study. Statistical analyses investigated relationships between (1) rock burst occurrence versus blasting, (2) rock burst size versus damage, (3) rock burst occurrence versus average micro seismicity rates, and (4) rock burst occurrence versus local mine geometry. Statistical analyses showed that 91% of all rock bursts occur with blasting while only 3% of all rock bursts occur, apparently, independent of blasting. Additionally, the long-term average daily micro seismicity rates appear to dictate when blasting will trigger rock bursts. Time series analysis on the daily microseismicity resulted in model equations that may be used to forecast the daily microseismic activity.

Jan 1, 2010

By C. H. Fisher

[Mxny methnhs of ,analyzing tpr oils fnr thoir tar acid ~nd base cnntent hava boon employL~d in connection mith both ac~d,.mic and. industrial investigs- tions. Mnst of thznu nnalyticel proc?durn~s aro bpsed nn th; diminution in volums caused by extract lon sit5 alkali 5 minL+ra,l acids (cantrsction rn,>thod) , although othrr mr~thrids havu &apos;sL<on ?q~lnglt 8 . In many instmccs th-: donti ti on of RT~ m~lytic~l m ithod was not ;r.:c ~d~d by ~d.jqunt9 study, and, ns 3 cone+ qucnce, tha lit .,ratur ? on thls sub,jr:.ct is consoScuous for its cnntr~dictnry . claims and rocnmmondatinna.. 1.t tiR.s b9~n shoyn in th;, cnsn of c.lrtn.in synth?tic solut innsfi/ thnt larg~ jr-orn sny rcsult if th2 ,mnlysis is c~rri~d out by sim~la extraction wi.th alidi r.nd min 3rd ncids.]

Jan 1, 1937

By M. A. Elliott, F. W. Brown

"INTRODUCTION During the recent war the Bureau of Mines, at the request of one of the armed services, investigated the hazards that night be encountered 5n handling perchloric acid, particularly if spilled on certain materials. The hazardous nature of perchloric acid when mixed with reducing agents had been known qualitatively, but it was desired to obtain quantitative data on the explosion hazards of such materials. Accordingly, tests were made to determine the sensitivity of mixtures of perchloric acid and oxidizable materials to initiation by heat, impact, sparks, flame, and explosive impulses. This report summarizes the results of those tests.PROPERTIES OF PERCELORIC ACIDAnhydrous perchloric acid is a colorless,hygroscopic, volatile, mobile liquid that fumes in the air. The anhydrous acid is unstable at ordinary temperatures, and therefore the commercial acid is a water solution containing either 60 percent or 70 percent by weight of the anhydrous acid. The commercial acid is widely used in chemical analysis, frequently to oxidize organic material. If proper precautions are not observed, such an oxidixation may become exceedingly rapid and result in an explosion. Several such explosions involving the acid are mentioned in the literature. 4, 5, 6/"

Jan 1, 1948

By S. Vennos

As a result of Synopsis 73-16 Dynadyne responded with an unsolicited proposal offering the Bureau of Mines to develop an ultra-low volume coal mine dust personal sampler. In the ensuing technical discussions the choice of a desirable volumetric rate became a focal point. While, the initial proposal was based on a volumetric rate in the area of 50 cc/min the Government expressed interest in a variety of mass flow rates ranging from 50 cc/min to 2000 cc/min. The physical characteristics such as weight, volume and configuration of a personal sampler are to a large extent - dependent on the operating volumetric rate. It became readily apparent that the optimum size of such an instrument as a function of volumetric rate was not known and that a study of the choice of optima was essential prior to beginning the development, Hence, the Government authorized a two phase approach to this project. Phase I was to include a Technical Evaluation Study of optimum characteristics in the range between 0. 1 to 2. 0 lpm. Based on these findings and in consultation with MESA personnel, the Bureau of Mines was to authorize the second phase that is, the development. Phase II, was to include the drawing of a set of performance specifications stating among others the desired operating volumetric rate. In this report, every effort was made not only to present the actual work done over the course of this development, but to reflect also our engineering "thinking" providing answers as to the "why" we preferred certain solutions over others. We believe that this added dimension is not only useful for the Government official evaluating this report, but also that the Government is entitled to it providing the official with an educational content useful in avoiding future costly repetitions of similar situations.

Jan 1, 1975

By C. S. Allbright

This report gives the results of analyzing three groups of crude shale oils by the Bureau of Mines procedure:4/ (1) Oils produced by standard Fischer assay determinations on oil shales from Brazil (Paraiba Valley) and the United States (Colorado); (2) oils produced from Brazilian shale by different retorting methods; and (3) oils from high-temperature retorting of Colorado oil shale in the Entrained Solids retort. It is the second in a series presenting data obtained by analyzing crude shale oils from various sources. The series furnishes information on the general characteristics and compositions of a wide variety of shale oils. Use of a standard analytical method on all samples facilitates comparison of different oils. The 18 oil samples analyzed in this project comprised 3 from assays of Brazilian and Colorado oil shales in the Fischer retort, 9 obtained by processing Brazilian shale in various other units, and 6 from entrained solids retorting of Colorado shale at 1,000° to 1,500° F. The crude oils from Brazilian shale contained about half as much nitrogen as the Colorado oils. Properties of the Fischer assay oils from Colorado shales agreed with some data that relate grade of the oil shale with properties of the crude oil from the Fischer assay. Comparison of results from Fischer assays of oils from the foreign and domestic shales shows that the oil from Brazilian shale contains more low-boiling material and less residuum than either of the two from Colorado shale. This fact is reflected in lower specific gravity, viscosity, and carbon-residue values for the Brazilian oil. Retorting Brazilian shale in the Entrained Solids unit at 1,120° F. produced an oil whose boiling range was generally lower than the boiling ranges of oils obtained by processing in three other retorts at conventional temperatures. The quality of crude oils from high-temperature retorting of Colorado shale in the Entrained Solids process varies with retorting temperature. As the temperature is raised within the range 1,000° to 1,500° F., the amount of the naphtha fraction in the crude oil increases to about 35 percent and the aromaticity to 98 percent.

Jan 1, 1956

By A. C. Fieldner

In 1927 the Carbonization Committee of the American Gas Association proposed cooperation with the Bureau of Mines in the development of suitable methods for determining the carbonizing properties of American coals. It was further proposed to apply these methods in the testing of representative coals and to make the information obtained available to the public through Government publications. A cooperative agreement was signed whereby the Gas Association contributed part of the funds necessary for beginning the project and appointed a committee to consult and advise the Bureau in the work. The Advisory Committee has been reappointed each year, and the Bureau has had the benefit of its advice. The composition and carbonizing properties of 33 coals previously tested have been given in technical papers of the Bureau of Mines and in short reports published for the most part in the Proceedings of the American Gas Association. A complete list of publications on the work previous to 1937 is appended to this report. The present report gives the composition and carbonizing properties of seven additional coals from West Virginia. The data include results of blending tests in which Beckley led low-volatile coal was used with all the high-volatile coals except the Alma coal, with which Pocahontas No. 4 coal was used.

Jan 1, 1938

By R. L. Crosby

Microscopical and X-ray diffraction techniques were used to identify two intermediate phases in that part of the solid region of the magnesium-cerium system between and Mg3Ce. Previous literature had reported only one intermediate phase for this region, 1)12t chemical analysis determined the approximate composition of the two compounds to be Mg23Ce2 and Mg17Ce2. The range in composition of the two intermediate phases was found to be limited to less than 0.3 atomic percent cerium. The study did not determine the crystal structure of Mg17Ce2, but that of Mg23Ce2 is tetragonal with a = 10.33 A and c = 19.51 A.

Jan 1, 1966

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (CFR) Com¬mittee of the Coordinating Research Council (CFC) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36. 4/ Further re¬ports were issued describing motor gasolines sold during the succeeding summers and winters to and including the summer of 1941.4/ No reports were made on motor gasolines sold during the winter of l941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed. The present report presents analytical data for 3,011 samples, representing the products of 113 companies. Most of the samples represented in this report were obtained during July and August 1946. As in previous surveys the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium-price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gasoline are not considered adequate to represent this type of motor fuel, data for the analyses have not been averaged, but the individual items are tabulated. The number of samples, items, and brands comprising each group is as follows: Regular-price, 1,585 samples, 311 items, and 99 -brands; premium-price, 1,422 samples, 280 items, and 94 brands; third-grade, 4 samples, 4 items, and 4 brands. The meaning of these terms as used in the survey is as follows:"

Dec 1, 1946

By D. Harrington, W. J. Fene

For nearly 30 years the Bureau of Mines has contended that mine explosions can be prevented and has pointed out to the industry ways and means by which they could be avoided. The record of co2l-mine explosions • during the past fiscal ?Bar bears out the :Bureau1s contention, inasmuch as fewer men were killed by coal-mi~e e:xplosions in the United States during that year than in :gi_y corresponding 12 months in the history of coal mining in the United States, insofar as records are available; and more than a year has elapsed since·a major explosion (in which five or more men were killed) has occurred, this being t.1-J.e first continuous 12- month period without a major coal-mine explosion disaster in the United States in more than 60 years. The methods of preventing mine e:iiplosions are well known to experienced, well-informed persons cngnged in coal mining. Despite this knowledge, many coal-mine operutors continue to use practices and methods that they should know have resulted in countless explosions, and mine workers persist in following past procedure or in breaking safety rules and practices almost certain eventually to result in disaster. ' Virtually all explosions are the result of human failure, such as carelessness or neglect by officials or workers or others. These human failures can be corrected chiefly by ed.ucation and proper and adequate supervision and strict discipline. In some instances mine officials are ·lax, careless, poorl~• informed, and often incompetent; end in many instances miners have repulsed the introduction of known preventive methods because of sheer obstinacy, ignorance, heedlessness, or possibly fear that the operator was trying to o'bta.in some unfair adva.,.'1. tago or would neglect some other phase of accident or e,:plosion prevention. The freedom of the fiscal year 1938-39 from major coal-mine explosions ar..d frora any considera~le number of fat,JJ.i ties from minor explosions is a. matter for congratulation, but on the other hand. the occurrence of one rather bad e~losion in each of tho 3 calendar years 1937

Nov 1, 1939

By Robinson Newcomb

Gypsum is a form of hydrated calcium sulfate (CaS04.2H20) which is widely distributed over the earth&apos;s surface. The two varieties worked commercially are rock gypsum and incite. Rock gypsum, the variety commonly mined for commercial purposes, is a relatively soft mineral having a specific gravity of about 2.3 and weighing about 150 pounds per cubic foot. The chief producing States are New York, Michigan, and Iowa. Before being used the crude gypsum is ground and generally calcined. The predominant use of gypsum is for building purposes (the manufacture of plaster), for which calcined gypsum is required. Gypsum is also used as a retarder in Portland cement, as fertilizer, and for other purposes. GYPSUM MINING Crude gypsum is mined by two methods - underground and open-pit. Although the use of the former method predominates, open-pit mining increased in relative importance during the early twenties and contributed about two-fifths of the output during the period 1925-38.

Jan 1, 1940

By J. Alton Burks

When acoustical materials are used in a mining environment for noise control purposes, they are subject to environmental deterioration from hydraulic fluid, moisture, and dust. These and other factors can cause physical degradation of the material, which can lessen its ability to absorb sound. In this study, the Bureau of Mines measured the sound absorption properties of 16 different acoustical materials after 4 sample treatments: (1) being kept clean and dry (as received from the supplier), as a control or reference standard, (2) immersion in water and draining, (3) immersion in lOO-pct-petroleum-type hydraulic fluid and draining, and (4) exposure in a coal mine. The last three treatments were used to approximate the type of physical degradation that can be experienced in actual use. The impedance tube or standing wave method was used to measure the normal absorption coefficient. It was found that the absorption coefficient of most materials was adversely affected by the retention of either oil or water, with oil having the greater effect. The only class of materials that was affected by neither oil nor water was neoprene foam.

Jan 1, 1990