Search Documents

By John K. Alley, Robert C. Johnson

The primary objective of the research was to grow aluminum borate whiskers or fibers and to determine their properties . Molten salt bath and vapor deposition methods were used for synthesis . Whiskers exceeding 25 mm in length were grown . The best results were obtained by vapor deposition and most of the data presented were determined on whiskers produced by this method of synthesis . Three different aluminum borate compositions ( 4.8A1203 B₂03 , 3.8A1203 B203 , and 2.5A120, B203 ) were identified by X- ray and chemical analyses . The aluminum borates 4.8A1203 B20, X- ray diffraction pattern was indexed . Optical data were obtained on the three aluminum borates . In addition the following whisker properties and growth factors were determined : ideal atmospheric dewpoint for vapor deposition method , near 65 ° F ; temperature range of whisker formation , 1,000 ° to 1,400 ° C for the molten bath method of synthesis , > 1,000 ° to < 1,400 ° C for the vapor deposition method ; whisker growth rates by the vapor deposition method , maximum 12 mm per hour ; raw material vaporization , 50 to 60 percent of the fluoride lost in 1 hour ; tensile strength , maximum obtained 174,162 psi ; melting points , ranged from 1,675 ° to 1,795 ° C.

Jan 1, 1965

By J. W. Town

The Bureau of Mines made continuous-circuit beneficiation studies to determine the optimum conditions for concentrating phosphate minerals from the intermediate-and marginal-grade ores of the Phosphoria Formation in southeast Idaho. Intermediate-grade ore was represented by a sample from Georgetown Canyon and marginal-grade ore from the Gay mine near Fort Hall. Two flow-sheets were developed: The first involved roasting, attrition scrubbing, sizing to remove a concentrate, grinding of the oversize, des liming, and flotation; in the other flowsheet roasting was eliminated. Controlled attrition scrubbing was used to remove clay and silt-size quartz particles imbedded in the phosphate pellets without breaking the pellets. The minus 35-plus 200-mesh fraction was removed by sizing as a finished acid-grade concentrate. The plus 35-mesh material was ground in a rodmill to minus 35 mesh and recycled to the attrition scrubber. The minus 200-mesh fraction was des limed at about 800 mesh to remove clay slimes and floated with 3 to 4 pounds of emulsion per ton of feed. The aqueous fatty-acid oil emulsion consisted by weight of 3 parts No.2 diesel oil, 3 parts crude tall oil, and 0.5 part water-soluble petroleum sulfonate.

Jan 1, 1967

By M. Hayashi

The Bureau of Mines conducted laboratory studies on Idaho mudstones to examine techniques for extracting vanadium. Recovery of vanadium from low-grade sources could contribute to future vanadium production and reduce reliance on imports. An Idaho mudstone surface sample containing 0.30 pct V205 and an underground sample containing 0.21 pct V205 were used in the extraction tests. Leaching of the surface sample for 18 h at 800 C with the addition of up to 1,000 lb/ton H2S04 recovered 70 pct of the vanadium. How-ever, leaching of the underground sample under the same conditions re-covered only 47 pct. By adding 15 wt pct NaCl and roasting the samples at 7500 C for 2 h, followed by leaching with 800 lb/ton H2S04, vanadium extractions were increased to 78 pct from the surface sample and 83 pct from the underground sample. Water leaching of samples roasted at 7500 C for 4 h with a 25-wt-pct NaCI addition yielded about 60 pct of the vanadium from both surface and underground samples. Autoclave leaching at 2000 C for 3 h with 1,000 Ib/ton H2S04 extracted 97 pct of the vanadium from the surface sample and 86 pct from the underground sample. An exploratory solvent extraction investigation to purify and concentrate vanadium in the leach solution using several organic reagents was also conducted.

Jan 1, 1985

By Gary P. Sames

The Bureau of Mines recently initiated a study of geologic features that contribute to roof instability in western U.S. underground coal mines. The purpose of the study is to provide information for use in ground control planning and safety hazard reduction in that region, where mining activity has been increasing. Hazardous geologic conditions were surveyed in selected underground coal mines in Utah and Colorado, and both depositional and structural features were identified as potential ground hazards. Although the conditions found do not differ in kind from hazardous geologic conditions in the Eastern United States, they do differ in intensity of occurrence and relative importance. Three depositional features dominate where unstable roof occurs in western underground coal mines: paleochannel deposits, crevasse splay deposits, and flood basin deposits. Three structural features identified as hazardous, but not so widespread or common as the depositional hazards, are faulting, jointing, and igneous intrusions. This survey establishes a foundation for future studies aimed at reducing and preventing ground control accidents in western coal mines.

Jan 1, 1988

By John E. Miller

Absolute viscosity values for gases usually are determined with a capillary tube viscosimeter, One of the correction factors applied to the experimental data is that for nonuniformity of the capillary bore. This report contains useful analytic expressions of the nonuniformity correction for the following cases: ellipse, cone, sine wave, sawtooth wave, square wave, and the general case. The methods herein described are applied to estimate the nonuniformity of a section of stainless steel capillary tubing to be used at the Bureau of Mines Helium Research Center. Several other examples are given to illustrate the usefulness of the present results.

Jan 1, 1967

By Edward C. Peterson

Recent studies indicate that the United States halt substantial reserves of ilmenite, one of the major titanium minerals. However, the studies showed that sources of rutile, another important source of titanium are limited. This paper summarizes and evaluates results and conclusions reached by the various investigations initiated by the Bureau of Mines and others pertaining to the titanium mineral resources of the Nation. Domestic occurrences of ilmenite that are economically exploitable by present-day beneficiation methods are found in Florida, New Jersey, New York, South Carolina, and Virginia. These deposits are estimated to contain 50.3 million tons of titanium dioxide (TiO2). Occurrences of ilmenite that cannot be processed economically under present technological conditions are found in California, Colorado, Minnesota, Montana, Oklahoma, Oregon, Rhode Island, and Wyoming. These reserves amount to 51.1 million tons of TiO2. Reserves of rutile found in the United States are estimated to be 1.8 to 2.1 million tons of TiO2. Other than occurrences in Florida and South Carolina, rutile is found either in small scattered bodies or in deposits where the mineral cannot be recovered economically by present beneficiation methods.

Jan 1, 1966

By Robert C. Johnson

Domestic byproduct fluorine (in fluosilicic acid) availability at various price levels of aluminum fluoride were determined and a contingency availability curve developed. The supply of byproduct fluosilicic acid is restricted in amount to certain geographic regions, where plants processing phosphate rock are located, and the byproduct can be collected. The maximum possible U.S. annual supply, based on potential plant capacities, is 373,400 tons of fluosilicic acid containing 295,400 tons of fluorine. Based on inputs of 5, la, 25, 50, and 100 thousand tons per year, five levels of producing aluminum fluoride from fluosilicic acid (100 percent) were costed. Based on a 12-percent discounted cash flow rate, including the cost of salvaging the fluosilicic acid, the calculated selling price of aluminum fluoride ranged from $233 per ton to $448 per ton. At the higher price, 98 percent of the potential supply of byproduct fluosilicic acid could be used profitably; at the lower price only 46 percent could be used profitably.

Jan 1, 1973

By C. H. Gorski

Evaluation of raw materials for mineral wool is one phase of the Bureau of Mines broad program for the more effective utilization: of our mineral resources. The experimental work and test-evaluation results on several raw materials as useful components for the production of mineral wool are presented in this report. Samples from all sections of the United States, including copper slag from Tacoma, Wash., pebble phosphate slime from Florida, and granites from Massachusetts and Minnesota, have been blown into mineral wool successfully in the laboratory tests. Maximum conservation of the Nation&apos;s mineral and manpower resources requires maximum utility of those resources. Al though the domestic reserves of oil, gas, and coal are tremendous, judicious use of these fuels through the use of proper insulation will insure the highest thermal efficiency. The effectiveness of mineral wool as a heat-insulating material has assumed an increasingly important role in the national economy, and it has become a fuel saver in countless applications. The most immediate concern to many is the use of mineral wool in the home, which promotes uniform temperature and minimizes drafts by reducing heat transfer through the walls, ceiling, and floors. There are, however, many industrial and commercial uses that require large volumes of mineral wool each year.

Jan 1, 1951

By E. J. Gleim

[THE ORGANIC act under which Federal Bureau of Mines was established provided for the investigation of the safe use of electricity in mines. Each Congress appropriates funds for conducting this investigation. As part of this investigation, electrical apparatus used in mines is studied to determine if its operation and use might introduce a hazard. From this study, certain safety standards have been developed. These standards, established with the aid of both the manufacturer and user of such apparatus, are published in schedules, and apparatus that complies with the requirements set forth these schedules is classified as "permissible." This term is defined to designate apparatus as "completely assembled and conforming in every respect with the design formally approved by the Bureau of Mines." In the judgment of the Bureau, the manufacturers of such apparatus have adhered to certain minimum standards of safety in supplying a product that when properly used and maintained is safe for operation in mines where flammable gas or coal dust may accumulate. This work of the Bureau of Mines for increasing safety does not make it obligatory for manufacturers of mine equipment to produce only that of permissible classification. Before the effective date of the Federal Mine Safety Code,5 the Bureau sought to promote safety by recommending that mine operators install permissible equipment in gassy mines as a preventive measure against gas and dust explosions initiated by electrical equipment. For some years, the mining laws of several States have prescribed the conditions under which permissible equipment must be used. The Federal Mine Safety Code requires that ?all new electric face equipment and replacements of equipment purchased for mines where nonpermissible equipment is now being used shall be of a permissible type approved by the United States Bureau of Mines,]

Jan 1, 1955

By J. M. Singer

Methods are proposed for predicting concentrations of nitrogen oxides and carbon monoxide in the combustion gases of flames, specifically of lean, stoichiometric, and rich propane-air flames. Calculations are based on kinetic and thermodynamic theory. These theoretical data are compared with concentrations observed experimentally downstream of flat grid-type burner flames (approximately 25,000 Btu/hr) that were used to simulate gas appliances such as water and space heaters. Air pollutant concentrations are also computed for (1) flames chemically perturbed by recycling flue gases into the primary fuel-air mixtures; (2) flames thermally perturbed by cooling the burned gases at different rates; and (3) flames perturbed by combination of these two effects. In general, experimental and computed concentrations agree to within a factor of 2 to 7 with the experimental values always being higher than the theoretical. The theoretical analysis indicates that cooling the primary flame by recycling cold flue gases (with and without excess air) reduces the relative emission of nitric oxide and increases emission of carbon monoxide if the flame stoichiometry does not radically change. Cooling rates of about 5,500° to 10,000° R/sec starting at about 3,500° R generally suffice to prevent nitric oxide concentrations in lean flames from increasing much above the initial values at the combustion zone; these same cooling rates do not prevent oxidation of most of the initial carbon monoxide.

Jan 1, 1967

By C. E. Wyndham

The occurrences of manganese In Alabama were reported to be widely scattered over the northeastern section of the State, and these were examined before a development project was started.2/ The most promising and available showings were chosen for further investigation, which include 1 deposit in Goshen Valley, 6 in the Rock Run area, and 2 in the northern section of Calhoun County. The work was performed by the Bureau of Mines from July 29, 1949, to February 17, 1950. The work consisted of power auger drilling 69 holes 3-1/2 inches in diameter and totaling 2,548.4 linear feet. The accuracy of samples from auger drill holes in this type of deposit was determined by sinking two shafts a total depth of 68.17 feet, from which channel samples were cut. Sixteen rotary core holes totaling 1,048.7 linear feet were drilled with a 3-inch, double-tube core barrel. Twenty-two diamond core holes were drilled with a 2-1/8-inch, double-tube core barrel and NX diamond bit. In addition to the above drilling 220.8 cubic yards of soil and rock was excavated by hand from 403.9 linear feet of trenches and 69.7 feet of test pita. A total of 206 samples were taken and analyzed for manganese, iron, cobalt, nickel, and insoluble.

Jan 1, 1953

By B. W. Gandrud

In 1927 Coghill showed that there is considerable liberation of the iron oxide mineral from gangue when the Alabama red iron ores are ground to a size suitable for classification and tabling but that there is not sufficient to make possible a high extraction and a high grade of concentrate. Coghill states: High extraction and &apos;high grade of concentrate cannot be obtained without grinding to a size comparable with flotation or cyanide practice. If grade of concentrate be sacrificed the grinding need not be so severe. These ores slime readily during grinding, and in most instances the slimes are only slightly higher grade than the original ore. Not only do they carry a considerable percentage of the total iron in the ore, so that to reject them as tailings would result in prohibitively low extraction, but they are too fine to be amenable to ordinary methods of gravity concentration. In 1929 the Bureau of Mines published results showing that certain Alabama oolitic iron ores could be concentrated by classification and tabling after grinding, with rubber-covered rods. This selective grinding produced slimes of much higher grade than the original ore, and they were considered part of the final concentrate.

Jan 1, 1934

By D. A. Reynolds, R. G. Travis, James J. Dowd, R. F. Abernethy

"1. Reserve estimates have been made for eight coal beds in Monongalia County, W.Va., but only the Pittsburgh, Sewickley, and Upper Freeport beds are important at this time. The Pittsburgh, Sewickley, Waynesburg, and Upper Freeport beds contain the largest recoverable reserves.2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 3,526 million tons as of January 1, 1954. Of this total, 3,294 mil¬lion tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.3. Recoverable reserves of coal have been estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Monongalia County, as determined by this investigation, is 47.9 percent. This percentage is based on the total thickness of coal (less partings three-eighths inch thick or more) in the bed rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Monongalia County, the recoverable reserves are estimated at 1,577 million tons as of January 1, 1954.4. Monongalia County coals of the major producing beds are of high-volatile a bituminous rank.5. The Pittsburgh and Lower Freeport beds in this county yield coal that can be used as metallurgical coal, especially when blended with low-volatile coals. The Lower Freeport coal is coked singly and in beehive ovens, and makes good metallurgical coke.INTRODUCTIONThe investigation to evaluate the reserves of coking coal was planned to cover three phases: (1) Estimation of known measured and indicated recoverable reserves of all coking coal; (2) study of methods of upgrading marginal coals through effective preparation; and (3) study of carbonizing properties of coals and coal blends not now widely used for metallurgical coke making."

Jun 1, 1956

By W. A. Selvig

[THE BUREAU OF MINES receives many requests for information regarding the low-temperature carbonization properties of American coals. This report presents in collected form the results of Fischer-Schrader bench-scale, low-temperature carbonization assays at 500° C. made by the Chemistry and Physics Section at the Pittsburgh station of the Bureau of Mines. Most of the assays were made of coals tested in connection with a survey of gas and coke-making properties of American coals,4 which was started in 1928 by the Bureau in cooperation with the American Gas Association. Other coals were assayed in connection with miscellaneous investigations. Since 1930 about 400 samples of coal were assayed from nearly every coal-producing State, Alaska, and British Columbia, Canada. The results of the tests on about two-thirds of the coals are scattered through more than 50 separate publications. This paper summarizes the data in the published reports as well as all unpublished data obtained to January 1, 1956. The report also includes a detailed description of the procedure used in making the assay.]

Jan 1, 1957

By Richard D. Miller

This publication contains routine analyses and related source data for 295 natural gas samples from 18 States collected during calendar year 1963 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863/ and 576.4/

Jan 1, 1965

By Richard D. Miller

This publication contains routine analyses and related source data for 295 natural gas samples from 18 States collected during calendar year 1963 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863/ and 576.4/

Jan 1, 1965

By J. F. Barkley

To reduce fuel consumption in industrial and commercial fuel-burning plants throughout the Nation, cooperative efforts of thousands of individuals are required. These individuals are scattered over the country and hold various positions in thousands of independent establishments. To accomplish as much as possible on this problem during the Second World War, it was decided that personal contact with fuel users was absolutely necessary; publicity, although an important factor, could not by itself give satisfactory and needed results. It was planned to have qualified engineers visit commercial establishments to go over with them the problem of reducing their fuel consumption. The specific plan, toward which all efforts aimed and around which the rest of the program revolved, consisted in brief of 1. Conference of visiting engineer with management to obtain cooperation. 2. Appointment by management of a plant employee as fuel "waste chaser." 3. Work of engineer with "waste chaser" and, if appropriate, with plant operators on most efficient operation of equipment.

Jan 1, 1948

By Ellsworth Spencer

Noise induced hearing loss continues to afflict workers in many occupational settings despite longstanding recognition of the problems and well-known methods of prevention and regulations. Sound levels associated with heavy construction equipment range from 80 to 120 dB(A) and power tools commonly used in construction produce sound levels up to 115 dB(A).(1) The focus of this research was to determine the noise exposures of heavy construction equipment operators while documenting the workers’ tasks, (i.e. hauling, moving, and/or pushing construction material). Time-motion studies were performed at the construction sites and were used to correlate the noise dosage with the work performed by equipment operators. The cumulative dose for the operator was then plotted with references to work tasks, to identify the tasks that caused the greatest noise exposure. Three construction sites were studied for this research located in the western Pennsylvania and eastern Ohio areas. The types of construction equipment studied included asphalt pavers, backhoes, bulldozers, compaction equipment, excavators, haul trucks, telehandlers, and wheeled loaders. The results showed that bulldozer operators consistently had the highest noise exposures, ranging from a NIOSH REL (Recommended Exposure Limit) dose of 844% to 25,836% and an OSHA PEL (Permissible Exposure Limit) dose of 139% to 1,397%.

By James H. Scott

Well-logging techniques that have been used to evaluate various types of mineral deposits are discussed briefly, and many pertinent references are cited. Information is categorized by mineral commodity to make it easy to determine what logging techniques have been used for evaluating specific metals and nonmetals. Part 1 discusses logging techniques applied to deposits of the following metals: aluminum, antimony, beryllium, boron, copper, iron, lead and zinc, maganese, mercury, nickel, silver and gold, tin, tungsten, and uranium. Part 2 covers the following nonmetals: coal, evaporites, fluorspar, oil shale, rock salt, and sulfur. Separate bibliographies are given for English and foreign language references.

Jan 1, 1974

By Arnold B. Hubbard

A thermal decomposition study of the kerogen in three Colorado oil shales was made at different temperatures by heating the shales in the absence of oxygen at atmospheric pressure and measuring the decomposition products (gas, oil, and bitumen) formed. From these data the specific reaction rates, "k", for the thermal decomposition of kerogen were determined for each temperature studied, making it possible to calculate the time required to accomplish a given amount of decomposition within the temperature range. The influence of temperature on reaction rates was presented by plotting the data according to the Arrhenius equation, thus providing a means of estimating the values of "k" for any temperature within the range of this study. It was found that the specific reaction rates for the thermal decomposition of the kerogen in the three sampler were comparatively equal at corresponding temperatures.

Jan 1, 1950