Search Documents

By Michael Sokaski, M. R. Geer, H. F. Yancey

This report is one of a series describing investigations by the Federal Bureau of Mines of the performance of various types of coal - cleaning equipment ; other reports in the series are listed in the bibliography . The information in these reports is useful to the coal industry and the manufacturers of coal - cleaning equipment in several ways : First , it assists the coalpreparation engineer who is planning a new plant to select the type of process best suited to the requirements by enabling him to forecast the yield and quality of clean coal obtainable with each type of equipment . Second , the information serves as a yardstick by which the performance of a plant can be judged and thus helps determine whether it is operating at satisfactory efficiency . Both these functions promote better coal - preparation practice ; that is , they help provide coal of more suitable quality for the market and likewise minimize the waste of good coal . This serves the interest of conservation with which the Bureau is vitally concerned . The present report deals with three plants using the Tromp dense - medium process , named after its inventor , K. F. Tromp , who developed the process in the Netherlands in 1936.5/ Selection of this particular dense -medium process for investigation was entirely a matter of convenience , and reports dealing with other dense -medium systems are planned for the future . Two baths are employed in one of the plants investigated . The first of these , handling 6- to 3 - inch coal , exhibited an exceptionally sharp separation between coal and impurity . This was characterized by an error area of 12 and a probable error of 0.023 . In the second bath , treating refuse from the

Jul 1, 1960

By C. A. Herbert

This paper sets forth the hazards of accumulations of explosive mixtures of methane and air due to inadequate ventilation, the causes of which are discussed as follows: 1. Lack of well-maintained air courses. 2. Air losses due to leaky stoppings, trap doors, and overcasts. 3. Faulty mining methods. 4. Poor supervision. A modified plan of room-and-pillar panel mine development is suggested, which, it is believed, will eliminate many off the hazards of gas accumulations inherent in the present method of mine development. It is also suggested that some water-proofing agent be used on the roof of permanent air-course entries in conjunction with roof bolting to eliminate the detrimental effect of the moisture-laden atmosphere during summer and thus prevent serious roof falls.

Jan 1, 1953

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 29,020 acres of the 43,165-acre Terry Badlands Wilderness Study Area (MT-024-684) in order to evaluate its mineral resources. Within this report, these 29,020 acres are referred to as the study area. Located in Custer and Prairie Counties, MT, the study area is about 2 miles northwest of Terry. The study area is underlain by essentially flat-lying units of the Fort Union Formation of Paleocene age with some Quaternary alluvial deposits in stream valleys. No mines or prospects were found in the study area. Bentonitic clays and lignite coal units were examined and sampled; however, no clay resources or coal reserves were identified. Estimates of coal resources will be reported by the U.S. Geological Survey in a joint U.S. Geological Survey-U.S. Bureau of Mines publication. Gravel along the Yellowstone River, a source of agate for private collectors, could also be used as sand and gravel aggregate although material on the south bank of the river is closer to population centers and road systems. Clinker found in the study area could be a source of road metal, but is not well situated in relationship to areas of use. No geothermal resources have been identified although water suitable for direct heat applications may underlie the study area. All the area is leased for oil and gas exploration.

Jan 1, 1985

To develop a safety training module for surface miners and road construction workers exposed to the hazards of highwalls. Background Investigators collaborated to develop a new training module that would address the hazards of working around highwalls. Such a module would be applicable to surface mines and road construction sites, both of which require personnel to work under and on top of steep and often unstable slopes.

Aug 1, 2004

By Oren C. Baptist

[Several new oilfields have been developed in northwestern Wyoming during the past 10 years, production is obtained from discontinuous, permeable sands enclosed within impermeable shales. The energy to drive the oil to producing wells in supplied by gas in solution in the oil. Most of the wells had high-initial potentials, but rates of oil production have steadily declined, indicating a dissipation of the driving energy and the possibility that large volumes of oil will remain unrecovered in the reservoirs. The studies reported in this paper were undertaken to develop laboratory data of the type most likely to be needed by persons studying the susceptibility of the Newcastle sand reservoir to secondary-recovery methods.]

Jan 1, 1957

By H. G. Skavlem

This paper is prepared the United States Bureau of Mines and is descriptive of methods, practice, and costs at the McIntyre Porcupine Mines, Ltd., Schumacher, Ontario. The property is located in the Pearl Lake section of the Porcupine mining district. It is reached by a branch line of the Temiskaming & Northern Ontario Railway from Porquois Junction. There is also a good motor road into the district. The Hollinger Consolidated Gold Mines and the Coniaurum Mines, Ltd., are adjacent properties. Power for both the mining and the pulp and paper industries in the district is supplied by an extensive development of the water-power resources. Weather conditions are favorable for mining operations.

Jan 1, 1933

By Frederick C. Trutt

A guide to the utilization and development of extensions and modifications to the APL Mine-electrical-system Load-flow Program is presented. These modifications include the development of algorithms to minimize computational operations within the iterative-solution techniques, as well as minimization of the number of required iterations. Extensions to the load-flow program include the development of algorithms for the calculation of balanced faults, simplified specification of fault parameters, optional inclusion of pre-fault currents, and an alternate-solution technique.

Jan 1, 1978

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grind-ability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1965

"Contained in this chapter is a listing of the publications and reference books which have come about as a result of respirable dust research performed by faculty, staff and graduate students in the Generic Mineral Technology Center for Respirable Dust at The Pennsylvania State University, West Virginia University, University of Minnesota, Massachusetts Institute of Technology, and Michigan Technological University. These publications have appeared in scientific journals, proceedings of the national and international symposiums, and professional meetings. Complete citations of the publications can be found in Volumes 3 through 6 and Volume 8 of this series. The agenda of the last annual GMTC seminar, held at West Virginia University on February 1 - 2, 1988, follows. The project presentations are organized under the five research areas. All projects currently active were presented to the Advisory Committee. New project submissions were not. The authors were allotted thirteen (13) minutes for their presentations; the remainder of the twenty (20) minutes allotted for each project was used for introductions, transitions, and questioning by the Advisory Committee. Each author used a standard format for presentation of his/her materials for review; handout materials were distributed to the Advisory Committee for reference. Opening remarks were made by Dr. Richard Bajura of West Virginia University and Dean Robert L. Frantz and Dr. Raja V. Ramani of The Pennsylvania State University.The Generic Mineral Technology Center for Respirable Dust is funded by the U.S. Bureau of Mines through the Mining and Mineral Resources Research Institute Program. The opinions and conclusions expressed in these papers are those of the authors alone and do not represent the opinions of the Generic Mineral Technology"

Aug 31, 1989

By E. J. Lintner, J. R. Thoenen

During the period 1937-40 and until peacetime research was superseded in 1941 by wartime activities , the junior author was engaged in studies regarding the relative efficiency of operating methods in quarries producing crushed stone for mineral aggregates . The results of some of these studies were published as reports of investigations in 1939 and 1940 ; / others were discontinued due to war demands on personnel and time . The published reports discussed the efficiency of particular quarry operations with respect to the time consumed and without reference to costs or mechanical factors . • At the time , the field data were collected for the published reports other data were collected relative to the relationship of the numerous variable factors inherent in the operation of a churn drill to the ability of the drill to produce blast holes . The churn drill is essentially a crusher and depends. for its performance upon the foot-pounds of energy it can impart to the cutting edge of its bit . The gravity stamp mill , so well-known in western gold mines , is essentially the same type of crusher . The ratio of foot- pounds necessary to crush the rock , to the total theoretical energy developed by the falling churn- drill tools , affords a good means of evaluating the efficiency of the tool . This does not include to tal over-all efficiency involving the mechanical equipment of the drill itself or its power unit .

Jan 1, 1947

By Raymond W. Hiteshue, Sam Friedman, Robert Madden

Experiments were made in a semicontinuous unit to provide engineering data for designing experimental continuous systems . These systems would be used to study the hydrogasification of hvab coal and char (from lowtemperature carbonization ) to high - Btu gas . In experiments at 800 ° C and with a coal residence time of several seconds , yields of hydrocarbon gases increased from about 2,000 scf / ton of maf coal at 250 psig to 7,000 scf at 1,000 psig . With 15 minutes residence time , yields increased from 8,000 scf/ton of maf coal at 250 psig to 17,500 cubic feet at 1,000 psig . In all cases , small quantities of heavy oils were produced along with the gaseous hydrocarbons . Production of oils could be minimized with a corresponding increase in gaseous hydrocarbons by increasing the retention time of the volatiles within the hot zone . Yields of gaseous hydrocarbons from char were slightly greater than from coal under similar conditions . Although the hydrogasification reaction is very pressure dependent , substantial quantities of coal (40 to 60 percent ) could be reacted to gaseous hydrocarbons at pressures as low as 50 psig provided reaction temperatures were increased to 1,200 ° C. It was also demonstrated that a hvab coal could be hydrogasified continuously without incurring agglomeration . This was achieved by dispersing coal in a relatively large reactor with concurrent flow of hydrogen . At 1,000 psig and 800 ° C , it was possible to react about 35 percent of the coal and to produce a gas containing up to 52 percent methane .

Jan 1, 1964

By M. Carrales

This Bureau of Mines publication presents short-range projections of domestic liquid hydrocarbon production through 1980. Appraisal of future crude oil production was made by evaluating the relationship between primary and enhanced oil recovery and the total crude oil producing trends in each of the oil-producing areas of the United States. Future natural gas liquid production was generally estimated by projecting historical production. Estimates of production were prepared for each of the oil producing areas and summarized for the Petroleum Administration for Defense (PAD) districts and total United States. From 1975 to 1980, crude oil production for the conterminous United States is expected to decline from 7.8 to 6.4 million barrels of oil per day (BOPD), and it is expected to increase from 8.0 to 8.2 million BOPD for the total United States. However, these estimates do not include additional production expected from the Elk Hills field in California and the Yates field in Texas. If included, 1980 production for the conterminous United States would be 6.7 million BOPD and 8.4 million BOPD for the total United States.

Jan 1, 1977

By R. V. Higgins

As part of a study of application of the Buckley-Leverett method to an analysis of oil-reservoir performance covering a wide range of relative permeabilities and oil saturations, a method has been devised for quickly deter-mining average water saturation at breakthrough from relative permeability data. The base for the relative permeability used in the report is either the permeability to air or the effective permeability to oil at the irreducible water saturation. The permeability to air also was used because of the large backlog of air permeabilities available to reservoir engineers. The basic data were calculated by an electronic computer and are presented in a single graph from which the point of breakthrough may be obtained. In this study the water saturation at the beginning of the depletion is the connate or interstitial or irreducible water saturation. These water saturations are considered to be synonymous and to have a practical value.

Jan 1, 1960

Water pollution has been an integral part of most mining operations in the past. Most mine planners had designed their mining operations with little or no regard for prevention of water pollution. The main planning element was always the economics of mineral recovery. Quite often the cheapest means of mineral recovery resulted in the largest water pollution problems. Recent water pollution laws have introduced a new economic element - water pollution control costs - to be considered in mine planning. Water pollution control costs can be extremely high. Foresighted planning can minimize these costs and provide better water pollution control. Effective pollution control preplanning can eliminate pollution from active mines and minimize pollution that may occur after completion of mining. Presently available technology can practically eliminate water pollution by treatment of the mine water. Use of water treatment during mining has no effect on the levels of water pollution after treatment ceases and the mine is abandoned. Therefore, this section of the report deals with preplanning to reduce water pollution, both present and future, by using at-source control techniques. Proper planning of mining and pollution control techniques should follow the concept of a complete, comprehensive reclamation plan. This plan should have control measures designed for all phases of mining from initiation through completion. Preplanning involves acquiring complete information concerning the future mine site, defining the reasons why mining could cause pollution from the site, and determination of available techniques to prevent or minimize formation or transportation of pollutants. Location of haulage and access roads and other mine related facilities should be included in preplanning for water pollution control. Mine site planning is the primary step in establishing any new mining area and is the key to a successful, non-polluting and economical

Jan 1, 1973

By B. E. Davis

Over 80 pct of domestic phosphate rock, which is the starting material for phosphorus-containing fertilizers, comes from central Florida deposits. As K-her grade deposits are depleted, lower grade phosphate ores containing 'Mg0 in the form of dolomite are encountered. Treating high MgO ores with present beneficiation technology will not yield a concentrate meeting specifications for acidulation. The Bureau of Mines conducted research on three high-MgO phosphate samples from south Florida. The sales contained, in percent, 5.4 to 10.2 P205, 1.9 to 7.6 MgO, and 35.3 to 60.1 acid insolubles. A technique of sizing, grinding, desliming, scrubbing, and redesliming was used to produce a feed suitable for continuous flotation studies, A conventional fatty acid-fuel oil rougher flotation followed by two to three cleaner stages resulted in concentrates containing, in percent, 30.7 to 31.3 P205, 0.6 to 1.3 MgO, and 2.5 to 4.8 acid insolubles. The P205 recovery from the flotation feed ranged from 55.1 to 89.7 pct.

Jan 1, 1984

By C. Ortuglio

The Bureau of Mines developed equations to determine the relationship of yields and products obtained from BM-AGA carbonization in 13-and l8-inch-diameter retorts. The developed equations indicate that results of carbonization in l8-inch-diameter retorts can be predicted from results obtained with l3-inch-diameter retorts.

Jan 1, 1966

By H. Dolezal

A laboratory study of acid-ferrous sulfate treatment of low-grade manganese ores from the Cuyuna range, Minnesota resulted in 93-percent extraction of manganese as manganese sulfate with consumption of 3.8 pounds of H2S04 per pound of extracted manganese. Two types of ore were treated in consecutive stages. The first are contained carbonate minerals of manganese and iron, both soluble in H2S04 solution. The second ore contained manganese oxide minerals, insoluble in straight acid solution but soluble in the ferrous sulfate solution obtained from treating the first ore. Leaching data were obtained by countercurrent percolation of coarse (minus-1/2-inch) ore particles at room temperature and by agitating minus-65-mesh ore particles in heated solution. Extraction of manganese and acid consumption were the same, but the percolation leach required 6 days compared with 1 hour for hot agitation. Variations in the size of ore particles treated, leaching time, acid concentration, solution temperatures, and method of applying ferrous sulfate solution to the oxide ore were studied. The effects of several reagents for removing iron from solution and improving filtration were also studied.

Jan 1, 1959

By J. E. Hamak

This publication contains analyses and related source data for 151 natural gas samples from 19 States. Of the total samples, 138 were collected calendar year 1989. The remainder were collected earlier, but releases to were not received until 1989. All samples were obtained and analyzed as part of U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1990

By Mark Sheppard

This paper is the third of a series recording the results of tests made at various quarries throughout the United States to determine (1) the relation between the size gradation of feed to, and product from, primary crushers, (2) the particle shape of the crushed. product, (3) the differences in gradation and particle shape produced by different types of primary crushers, and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Progress reports 1 and 2 dealt with comparisons of different types of crushers crushing the same type of stone. This report deals with relation¬ship between feed and product of two different limestones, as to size distribution and particle shape, when crashed in the same crusher.

Jan 1, 1938

By Albert W. Deurbrouck

The performance of four sand cones was evaluated by the Bureau of Mines in three preparation plants that utilized cones in various flow schemes. The cone at plant A was a simple two-product one that provided clean coal and refuse. Plant B had two cones; one cone made a primary separation and the other a secondary separation. The primary cone separated salable coal from heavy rejects. The secondary cone separated a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam markets. In plant C the sand cone was equipped with a middlings draw Which continually removed an intermediate specific-gravity product below the surface of the cone. The three primary separations of raw coal effected between floats and sinks were excellent. The recovery efficiencies for the plus 1/4-inch material ranged from 99.8 to 97.6 percent, the error areas ranged from 19 to 23 square centimeters, and the probable errors in specific gravity ranged from 0.033 to 0.024. The performance data of the two secondary separations varied from excellent in plant B, where the separation was on a par with the primary separations, to somewhat inferior in plant C, where the secondary separation was effected at the middlings draw.

Jan 1, 1965