Search Documents

By Sidney Katell

Covering the period from January 1961 through December 1961, this report is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. It is also the third report in the series to be prepared as a cooperative effort by the Bureau of Mines and the American Association of Cost Engineers. The cooperative agreement between the two groups provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related facilities, came from the following sources: 1. A.A.C.E. Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigation. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Utilization. 9. Cost Engineering. 10. Industrial and Engineering Chemistry. 11. Nucleonics 12. Oil and Gas Journal. 13. Petroleum Engineer for Management. 14. Petroleum Refiner. 15. World Oil.

Jan 1, 1962

By D. S. Burgess

An investigation of the hazard of spillage of liquefied natural gas (LNG) onto water is described. About 2,000 gallons of LNG were consumed in various tests. The initial vaporization rate of LNG following spillage was found to be 0.037 lb/ft2 sec; when the spill was confined, this vaporization rate was moderated after about 20 seconds by the growth of an ice layer on the water surface; when the spill was unconfined, a coherent ice floe was not observed and the vaporization rate was essentially time independent. The maximum diameter (in feet) of the spreading LNG pool was found to be given by 6.25 Wo 1/3, where Wo is the weight of LNG in pounds, Downwind of a natural gas source, time-averaged methane concentrations were given in good approximation by standard air pollution equations. However, peak concentrations were as much as twentyfold higher than average, adding an additional factor to the assessment of hazard. The effect of layering by the cold vaporized natural gas was similar to the effect of a temperature inversion on normal gases in the atmosphere. Small-scale explosions were observed on pouring LNG onto a water surface; no single explanation seems pertinent to all of the incidents observed.

Jan 1, 1970

On September 4, 2007, Mine Safety and Health Administration, in alliance with the International Union of Operating Engineers and the International Association of Bridge, Structural, Ornamental, and Reinforcing Iron Workers, presented the first annual Mine Construction Maintenance and Repair?s Safety Contractor of the Year Award to Artisan Contracting, Inc., of Cape Girardeau, MO. Eligible contractors located throughout the United States were nominated. Artisan Contracting was nominated by Illinois Cement Company located in LaSalle, IL. Illinois Cement Company is a Division of Eagle Materials Inc., located in Dallas, Texas. Mr. Larry Frankum President of Artisan Contracting Inc., stated, ?While it is gratifying to receive a wonderful award such as this, we must not forget how fragile a good safety record is. We must constantly remain diligent in pursuit of maintaining safe work sites.?

Feb 1, 2008

By C. E. Wood

[Because of the renewed i~,ortanc of the strate ic netal ~ngane8e the Bureau of Mines is conductin further ro~aarch on pyrometallurgica1 ~ethods of boneficiating 0 ngani.foro'l iron ores nnn lo\,f-~~r de oanganesc ores. Published data on .the l2~roI'let llurgica.l treatnent of tl::1.nganse8 ores have been revi .. \-'en by Jose-ph ? .2]

Jan 1, 1940

By Ronald T. Mayerle

In-1992, the U.S. Bureau of Mines conducted a mineral investigation of the Anderson Mountain study area, including RARE II area 4-942, in Lemhi County, Idaho. The 7,340-ha study area lies within the Salmon National Forest about one kilometer north of the old mining town of Gibbonsville (pop.: 100). The eastern boundary of the study area is formed by the crest of the Bitterroot Range. The crest also serves as the continental Divide, and as the border between Idaho and Montana. The study area lies within the Gibbonsville Mining District, an important past producer of gold from lode and placer deposits. Since the 1870's, several hundred claims for both types have been located in the study area. Thirty-six current (1992) lode claims and two patented claim groups (one lode and one placer) are wholly or partially in the study area. No placer claims are current. In all, twenty-seven lode and five placer properties in and adjacent to the study area were investigated. Workings on the properties included 2 caved shafts; 36 caved adits; 8 open adits; 120 small pits, cuts, and trenches; and 4 large dozed cuts.

Jan 1, 1993

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations wi.thin a multiple-seam configuration. At two mine sites where such ground interactions were present, the Bureau performed a complete geological analysis and installed and monitored instrumentation to gather pertinent data on rock mechanics. Overburden depth varied dramatically in the vicinity of the study area and reached a maximum at the study site; innerburden thick-ness was less than a pillar width (40 to 4S ft); heaving was experienced in both mines where sandstone and/or shale floor units were observed; overlays of the mine layouts show pillars were not totally superpositioned; a maximum of S in of roof to floor convergence was measured; and pressure readings indicated pillar core loading only and increased to a maximum of 7,000 psig over instrument setting pressure.

Jan 1, 1987

By L. A. Stewart

This paper describes all occurrences of barite in Arizona that were known or reported to the authors. The history, ownership, production, and geologic setting are discussed for most of the deposits. The uses and specifications of product grades are briefly discussed. Seventy-five deposits were examined in 9 of the 14 counties of the State. The descriptions are given under county headings. No occurrences were reported in the four northeastern counties of Coconino, Navajo, Apache, and Greenlee, nor in Santa Cruz in the southern part of the State. From about half of the deposits examined, 55 samples were taken; of these, 45 were for chemical analysis, and 8 larger samples, ranging from 100 to 350 pounds, for beneficiation tests. A 30-ton bulk sample was taken for pilot-plant tests. Bench-scale flotation tests of the eight samples employing several different procedures and reagent combinations yielded marketable-grade barite products with barite recoveries ranging from 60 to 97 percent. Five of the samples contained enough fluorspar to warrant its recovery. Acid-grade concentrates, which accounted for fluorspar recoveries of 45 to 70 percent, were obtained from three of these ores. Batch laboratory tests of a representative portion of the 30-ton bulk sample revealed that acid-grade fluorspar and high-grade barite concentrates could be recovered. Results of the laboratory and continuous pilot-plant tests of this ore will be presented in a separate report.

Jan 1, 1960

The Leuna Factory of the I. G. Farbenindustrie A. G., situated near Merseburg, is the biggest heavy-chemical plant in Germany and produces a very wide range of products, mainly based on hydrogen or hydrogen and carbon monoxide. Its principal products are ammonia, synthetic petrol derived from the hydrogenation of brown coal, and synthetic alcohols made from hydrogen and carbon monoxide. The plant was first, visited on April 21, 1945, by a team including E. Cotton, V. Haensel, E. B. Peck, P. K. Kuhne, H. M. Weir, L. L. Hirst, W. W. Odell, G. U. Hopton, H. Hollings, J. F. Ellis, and H. G. Simpson. It was again visited on May 8-24, 1945, by a combined British and American team consisting of R, Holroyd, M. A. G, Banks, D. A. Howes, A. J. V. Underwood, R. A. Taylor, W. F. Faragher, H. Schindler, and J. G. Allen. This team was later joined by J. F. Ellis and R. J. Morley. A third visit with particular reference to catalyst manufacture was made by W. F. Faragher and W. A. Horne, and the notes of these latest investigators have been taken into account in preparing the report. This report was edited by Dr. R. Holroyd.

Jan 1, 1946

By Verne E. Hooker

Stress-relief techniques and instrumentation have been developed through many years of research in the Federal Bureau of Mines and successfully used to determine the in situ state of stress in rock. This paper describes the drilling equipment and accessories for use with the Federal Bureau of Mines three-component deformation borehole gage. Operation and calibration procedures for the deformation gage are discussed in detail. Site selection and overcoring procedures are included to provide a complete working knowledge for surface or underground applications.

Jan 1, 1974

By Donald W. Baggs

This report describes economic mining feasibility studies conducted by the Bureau of Mines to estimate mining costs in the Porcupine mining area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of three mineral deposit types: 1) massive sulfide deposits containing zinc, copper, and silver, 2) vein gold, and 3)disseminated gold. Cost estimates were developed using the Bureau of mines Cost Estimating S,-stem. Discounted cash flow rates of return were calculated using the Bureau of Mines MINSIM (mining simulation) computer program. Three sets of metal prices were used in the study based on recent historical price information. Underground longhole stope mining of a massive sulfide deposit containing 25 pct zinc. 1 pct copper, and 63.6 g/mt silver was found to be economic at high metal prices at a quantity of 13,200,000 mt ore. Cut-and-fill mining of a 26,400,000 mt massive sulfide deposit was found to be economic at medium metal prices. Open pit mining of a similar deposit was found to he economic at medium metal prices and 26,400,000 mt ore, or at high metal prices and 6,600,000 mt ore. Underground mining of a vein gold deposit was found to be economic at a grade of 17.1 g/mt medium metal prices and 1,320,000 mt ore. Open pit mining of a disseminated gold deposit was found to be economic at a grade of 1.71 g/mt medium metal prices and a quantity of 39,600,000 mt ore.

Jan 1, 1986

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

This report describes the development of training materials for the operators of underground mining equipment in the underground metal and nonmetal mining industry. The objective was to determine the effectiveness and acceptability of these training materials and to provide the validated training materials to the industry. Ten modules were developed, based on industry need according to accident frequency, accident severity and exposure to the equipment. The final modules were an average of 20 minutes in length and used slides with synchronized narration on cassette tapes. Testing materials are included for use by the mines.

Jan 1, 1984

By Hanns J. Billmayer

This report, which covers the period from April 1975 to November 1975, describes the work performed in compliance with the requirements of Contract No. H0357091. The purpose of this contract was the development of protective canopy concepts applicable to rail haulage equipment used in underground coal mines.

Jan 1, 1976

By Mark Sanders

This report compares a proposed 10/60 "piggyback" 02 generating self-rescue unit to the standard CO self-rescue unit with respect to work task interference. A simulated low seam coal mine was constructed and subjects performed locomotion, shoveling, cart pushing, and timbering tasks with the 10/60 or self-rescuer attached to their belts. Task completion time was longer on all tasks when wearing the 10/60 unit, although only locomotion was statistically significant. The 10/60 unit was bumped over 100% more often than the standard self-rescuer. Implications for design of the proposed 10/60 container are: 1) unit?s container must be extra durable to withstand the added abuse it is likely to receive by low coal miners; and 2) extra consideration must be given to preventing the device from slipping on the belt while working, especially in low coal.

Jan 1, 1980

By G. T. Lineberry, W. J. Wiehagen

A Paradigm Shift As market economists, mine managers are interested in "staying in business" and even "prospering." Bottom-line results are the "order of the day." Concern for bottom-line results invokes questions such as: How much was produced? At what cost? And, was anyone injured? While these questions will always carry everyday emphasis at the mine, they are fundamentally lacking in that they often appear, especially to lower levels of management and to the production worker, as preeminent concerns. Driven by market economics, many organizations have decentralized, outsourced, downsized, restructured, and formed new coalitions. Investments in new technology and concentration on productivity have been part and parcel with these changes, contributing to improvements in both safety and efficiency. A reason for (and, perhaps a result of) these improvements has been the development of a highly experienced and flexible work force. These changes in mining present an interesting opportunity to modify a few paradigms about work life in general, and perhaps a few paradigms about how we invest in the miner, in particular. Studying these issues now might offer some interesting opportunities for the future, as the foundations for the next generation of mine workers are laid. With the average "experienced" U.S. miner five to fifteen years from retirement, perhaps a key determinant of future success in the world market might be how well we make the transition from today's work force to the work force of tomorrow. We can ill afford to wait a few more years to tap into the special knowledge residing within a veteran mining work force. The WCPM work Crew Performance Model, see pp. ) is one approach to defining, capturing, and transferring this expertise.

By W. A. Calhoun

This report gives results of metallurgical investigations performed by the Bureau of Mines on mineral samples taken during April 1959, from Hawaiian bauxite deposits on the islands of Kauai, Maui, and Hawaii. The bauxite samples were tested at the Bureau's Rolla Metallurgy Research Center, Rolla, Mo., to determine if alumina could be extracted. The results were encouraging. Extraction of the alumina by the American Bayer type digest of crude ore samples from Kauai, Maui, and Hawaii recovered 78.8, 73.1, and 70.0 percent, of the total alumina, respectively. These recoveries were increased to 82.8, 85.5, and 79.5 percent by modifying the treatment, which consisted essentially of calcination and weak caustic desilication to provide a residue. The residue was then treated with calcium oxide and digested in a strong caustic solution to extract the alumina.

Jan 1, 1962

By C. E. Wood

Because of the renewed importance of the strategic metal manganese the Bureau of Mines in conducting further research on pyrometallurgical methods of beneficiating manganiferous iron ores and low-grade manganese ores. Published data on the Pyrometallurgical of manganese ores have been reviewed by Joseph.5/ A method of treatment that has received less consideration than others is the matte smelting of manganese or the separation of manganese from the iron and the gangue in an ore b, formation of a matte, that consists principally of esulfide of manganese. A procedure of this type has been patented by Betts.6/ Lofquist7/ claims advantages for the production of a sulfide-oxide matte as a method of recovering manganese in alloys containing manganese and iron.

Jan 1, 1940

By Masami Hayashi

The Bureau of Mines estimated the cost for ,3 uranium ion-exchange recovery system using five grades of 17.0, leach solution producing 815,570 pounds of U 0? per year from an ammonium bicarbonate in situ leach solution. The system flowsheet consisted of four unit operations: (1) Multiple-compartment ion-exchange (MCIX) absorption; (2) MCIX elution; (3) precipitation of the uranium as yellow cake, filtering, calcining, and packaging; and (4) waste disposal. The total fixed capital cost of a system treating 2,000 gallons per minute of 0.1-gram-per-liter-U308 leach solution was estimated as $6,888,000. For n basic case of an MCIX system depreciating in 9 years, unit production cost of U308 was $3.51 per pound. A decrease in feed solution grade from 0.[4] to 0.03 gram per liter increased the production cost exponentially. Shorter depreciating periods significantly increased the production cost particularly for the lower grade feed solutions.

Jan 1, 1979

Minerals are vital to any industrialized civilization. Annually, the United States uses more than 4 billion tons of new mineral materials, or about 40,000 pounds per person-about half being mineral fuels and the other half being metals and nonmetallics. Stable and economic domestic mining, mineral, metal, and mineral reclamation industries are essential to the economy. The value of United States energy and processed materials of mineral origin exceeds $200 billion annually. Although a number of minerals are imported, especially some designated as "strategic and critical," most U.S. mineral supplies are derived from the domestic mines and processing facilities that you will be seeing, reading about, and visiting as you use this visitor guide. We hope you enjoy your experiences. This pamphlet, a guide to mining and mineral operations that may be observed or visited and some other points of interest relating to minerals, is intended to aid tourists and students who are interested in mining. Some may wish to study our Nation's romantic past; others may plan to enter the minerals industry as a career; still others may have a primary interest in conservation practices. The pamphlet is also intended to aid State and local officials, Chambers of Commerce, and mining firms in answering some of the many questions of tourists and students.

Jan 1, 1976

By Carlie E. Banks

Tasks during Phase I of this contract effort were performed in four principal functional areas. These were geology, hydrology, reclamation and mining. Data were gathered from literature reviews, mine visits, survey of manufacturers, consultation with government agencies, and unpublished or private communications with contractors and consultants. The data collected were analyzed for omissions or inaccuracies, then organized into tables, graphs and flow charts to provide a concise body of technical and cost data suitable for the engineering analyses required in Phase II of this contract. Maps illustrating estimated grade and thickness of the oil shale were prepared, some of which are included as exhibits to this report. A preliminary mine layout was performed to test the completeness of the collected data.

Jan 1, 1975