Search Documents

By B. R. Mohal, F. F. Aplan, S. Chander

"Dust abatement by water sprays involves the subprocesses of 1) collision between dust particles and water droplets, 2) adhesion of particles to droplets, and 3) engulfment of particles by the droplets. A review of the fundamental aspects of these subprocesses shows that collisions between particles and droplets are determined by aerodynamics and the size and surface charge of the particles and of the droplets. However, the adhesion and engulfment subprocesses depend upon the wetting characteristics of the particles. Although wetting agents (also known as surfactants) have been used as dust suppressants in several investigations, conflicting results are available regarding their effectiveness. In this paper, we show that these results can be explained if the effects of coal rank on surfactant adsorption and wetting characteristics are taken into account.The influence of several nonionic surfactants containing polyethoxy adducts on the wetting behavior of coal is presented. The wetting was determined by a modified Walker Test method, and contact angle measurements. The results show that the wettability of coal depends upon coal rank, structure of the hydrocarbon chain of the surfactant, and the number of ethoxy groups in the molecule.IntroductionDue to the inherent nature of the mining process, a large number of particles are generated, a portion of which becomes airborne to create dust. Dust can be aesthetically and environmentally unacceptable and it can also be explosive. Fine particles in the respirable size range ( < 5 urn) are con-sidered to cause lung diseases, namely, silicosis, pneumoconiosis, etc.(1) Several approaches to reduce dust in mine environments are practiced throughout the mining industry. These include decrease in generation of dust through improvements in mine machinery, ventilation (in which lower dust levels are achieved by dilution of contaminated air with clean air), and dust removal methods. Water sprays are most commonly used to remove dust par-ticles. Recently, scrubbers are reported to have been installed on mining machines to remove dust,(2,3) which also make use of water sprays to reduce dust."

Mar 1, 1989

"While control of dust-related diseases, the objective of the Generic Mineral Technology Center for Respirable Dust, is of prime importance from the human standpoint it is also essential to the economic well-being of the mining industry (FIGURE 23). Although significant progress has been made, the problem continues to be a major concern to the mining community. An increasing global demand for coal and other minerals means that production and the number of miners employed is on the rise. Therefore, the importance of this research to the mining industry cannot be overemphasized.The five areas of dust research are 1) control of dust generation, 2) dilution, dispersion and collection of dust in mine airways, 3) characterization of dust particles, 4) interaction of dust and lungs, 5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. Some experimental projects where the research is conducted almost exclusively in the laboratory may still rely on industry for imput. No industrial resources are necessary to the research of the non-experimental projects, for example computer modeling .The remaining research is classified as experimental and these projects do require interaction with industry in varying degrees. Periodic trips to mining sites in Western Pennsylvania, Southern Ohio, and West Virginia are necessary to record measurements or collect samples. Or companies may provide needed samples or equipment to the university for use in the laboratory. On several projects interaction is limited to advice or information supplied to the researcher by industry personnel."

Aug 31, 1989

By Vladimir Adamek

This paper describes the Bureau of Mines development of a novel subsidence prediction methodology suitable to the mining and geologic conditions in the Northern Appalachian Coal Region. It describes the computation of vertical and horizontal movements, inclination, curvature, and horizontal strains. The substance of this method is the separation of the effects of lithology by introducing a correlation between hypothetically homogeneous overburden and existing lithologic conditions, while providing for different mining conditions, i.e., underground geometry and overburden thickness. The effects of lithology have been expressed in the form of a variable subsidence coefficient within the subsidence trough. The subsidence coefficient is considered a constant for other predictive methods. Field data from 16 test sites at 11 Bureau longwall panel studies were used in the analysis. For each panel, the characteristics of the variability of the subsidence coefficient were defined. Regression analysis of the subsidence coefficients from all test sites on their locations relative to the edges of their respective panels yielded a third-degree polynomial equation. The results from additional longwall panel studies, not included in the regression analysis, were used to prove the validity of this method. To facilitate the use of this precalculation methodology, a computer program was written in BASIC for use on a personal computer.

Jan 1, 1987

Reduce dust exposure of longwall shearer operators by keeping them upwind of the primary cutting drum. Approach Use a different coal cutting sequence by cutting from headgate-to-tailgate, making the cleanup pass from tail-gate-to-headgate. How It Works The cutting action of the shearer drum is usually the primary source of respirable dust at longwall shearer faces. Dust exposure of the shearer operator is deter-mined by his position relative to the lead drum, which is normally in the raised position taking a full sump. On long-wall faces where the cut pass is taken from tail-to-head, against the primary airflow, the shearer operators must remain at their controls, on the return-air-side of the primary dust source, to maintain proper control. A simple method to lower shearer operators&apos; dust exposures is to extract the primary coal from head-to-tail, thus positioning the operators up-wind of the lead cutting drum. The bottom coal is then cut, and the floor cleaned by the trailing drum during the tail-to-head cleanup pass. This sequence places the primary dust source, the cutting action of the shearer drums, on the return-air side of both shearer operators, except when cutting out at the longwall headgate.

Jan 1, 1984

Improve the accuracy of commonly-used mine air velocity measurement techniques. Approach The Bureau of Mines, through a contract with Ketron, Inc., conducted a detailed study to establish appropriate, generalized correction factors for commonly-used air velocity measurement techniques. The techniques used were centerline readings, continuous traverse and split traverse vane anemometer readings, and smoke cloud readings (see Bureau of Mines Bulletion 589 for details on the proper use of these techniques). The various measurement techniques were used at different mine test sites to measure different air velocities. The data collected from the test sites were used in a statistical analysis which determined a generalized correction factor for each measurement technique. The correction factor multiplied by the measured velocity was used to provide the true velocity.

Jan 1, 1984

Monitoring systems can have numerous uses in the mine. They can aid in the efficient management of the mine by providing environmental trend data, production and maintenance control, and communications. In some cases, they can provide justification to petition the Mine Safety and Health Administration (MSHA) fog a variance of one of the mandatory safety standards. They may also increase the gross revenues of the mine by increasing the amount of coal produced or increase profits by reducing the cost of producing that coal. No single system will satisfy the requirement of all mines. Some may require simple hard-wired status-reporting systems; others, multipurpose computer-based systems that collect, analyze, and store data and perhaps control some mine functions. Even though systems vary in complexity, they are all composed of three functional components. The first component is sensors that measure the environmental or production parameters and produce an electrical signal that is fed into the telemetry. The second is telemetry devices that receive the signal from the sensors and transmit it in either analog or digital format to the third com¬ponent, analysis and display equipment. This equipment receives the transmitted signal and either stores it for later analysis or displays it. The analysis-display equipment ranges from simple strip chart recorders with preset alarms to computers, cathode-ray tubes (CRT&apos;s), and line printers that can also provide production reports. 4.2 Uses of a Mine Monitoring System A list of potential uses for mine monitoring systems, including both production-related functions and those related to health and safety, was used to develop a questionnaire. It was presented to representatives of the mining community to determine their current monitoring priorities. The responses indicated that the industry&apos;s priorities fall into the following two categories: First priority- Production and haulage Maintenance Second priority- Ventilation Communication Fire monitoring Personnel The survey shows that production-oriented systems were the most appealing to the questionnaire respondents. Since even small improvements in production efficiency and maintenance can have a large financial impact, the desirability of monitoring systems that focus on these areas is understandable. The results are summarized in table 4-1. The function that scored 100 was viewed as the most beneficial monitoring function.

Jan 1, 1984

To provide accurate navigation and control of continuous mining systems.

Jan 1, 1996

By David S. Yantek

A-weighted sound levels around vibrating screens in coal preparation plants often exceed 90 dB(A). The National Institute for Occupational Safety and Health (NIOSH) is actively developing noise controls to reduce noise generated by horizontal vibrating screens. A 121-microphone, 3.5-meter-diameter array was used to perform beamforming to determine locations of significant noise radiation on the screen. Below about 1 kHz, the screen body was found to be the most significant noise source. The beamforming contour maps showed several key locations on the sides of the screen and the feedbox are the most significant contributors. Operating deflection shape (ODS) analysis was used to examine the screen behavior under actual operating conditions. This information is helpful in determining how to modify the screen body to reduce the noise radiated by the screen below 1 kHz. The analysis showed modal vibration patterns on the sides and feed box were the main contributors to noise. The results show several areas on the screen sides and feedbox that can be modified to reduce noise.

Jan 1, 2009

By T. A. Henrie, D. C. Fleck, D. G. Kesterke

Uranium metal was electrowon from uranium dioxide dissolved in fluoride melts . The UO₂ was fed directly to the cell in a continuous manner . Electrolysis was performed at 1 , 200 ° to 1,300 ° C in electrolytes composed of UF4 , LiF , and BaFa . A single regulus of metal was collected in a confined area of the crucible . Product purity of 99.8 percent was attained . Carbon was the major contaminant . Compartmented cells were studied as a means of confining the oxide feed to the vicinity of the anodes .

Jan 1, 1964

By Henry M. Harris

The Bureau of Mines investigated a glass containing approximately 17 percent lithia and 83 percent silica to establish a method of devitrifying cast and rolled shapes. Glass shapes with high strength were made by melting, forming, and rapid cooling of the composition, and the shapes subsequently were converted to a crystalline condition by heat treatment. The best devitrification schedule included rapid cooling of the glass to below 300° C, followed by reheating at a rate of 50° to 400° C per hour, depending on the size of the shape, followed by a of 60 to 70 hours at 500° C and another period of 15 hours at 800° C. attempts to use faster heating rates or slow cooling to accomplish devitrification in deformation of the shapes. The crystalline shapes had flexural strengths that averaged over 33,000 psi, achieved with an annealing time of 60 to 70 hours at 500° C.

Jan 1, 1965

By Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH) in partnership with Strata Products tested the sealing capability of Ventstop®? as part of an ongoing mine fire control and suppression research program. Ventstop®? is a multi-purpose, inflatable device that is produced by Minvent Solutions and is available world wide for use in the metal and nonmetal mining industry. Ventstop®? is also used in the Australian coal industry as a temporary ventilation control device. The device can be quickly deployed, is reusable and can be placed in horizontal and vertical mine voids to control dust, fumes and smoke. Deployment, multi-day inflation and air leakage tests were conducted at the NIOSH Lake Lynn Laboratory to determine the capability and limitations of Ventstop®? in a simulated coal mine setting. During the tests, Ventstop®? was also subjected to low level forces of a nearby methane gas ignition. It is thought that Ventstop®? could be used by the US coal mining industry to temporarily close an underground mine area in response to a fire or spontaneous combustion heating event, to temporarily redirect mine ventilation during longwall equipment moves or during stopping construction. This paper describes this inflatable temporary mine sealing technology and presents the results of the NIOSH tests. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

Jan 1, 2009

By Thomas V. Falkie, R. Venkataramani

The empirical nature of this investigation required measurements of variables under operating conditions in underground coal mines. The variables to be measured were based on the postulated character¬istics of the loading function, as described in the previous chapter. One class of variables presumed to influence the loading function are geological variables. Accordingly, the sites for data collection were selected in different bituminous coal seams at dispersed locations in order that variation in geological conditions would exist. Seven mines in central and western Pennsylvania and one mine in northern West Virginia were selected as data collection sites. Five different coal seams were represented by these mines. The remaining classes of variables - geometric, mechanical, and procedural - were measured as they occurred in the mines. A description of the measurements, and the conversion of these measurements to forms which could be-analyzed for effect on the loading function is given. Mining Dimensions At the underground working face, the following dimensions were measured: a. Thickness of coal excavated. b. Thickness of shale excavated. c. Total height excavated. d. Width excavated. e. Depth of penetration of each machine cut. With the exception of the last of these dimensions, all were measured

Jan 1, 1972

By Alexis M. Herman

It?s school vacation time again, and kid?s thoughts turn from textbooks and term papers to fun and play, includ­ing outdoor adventures. Old quarries can become swimming holes on hot summer days; sand and gravel piles look like interesting playgrounds; aban­doned mine shafts beckon explorers. But, for the unaware, all three mean danger. Already this year we have seen two stark reminders that mines and minors don?t mix. In Oklahoma, a 13-year-old girl drowned while swimming with friends in an inactive strip mine. In Maryland, a six-year-old boy playing on a quarry site, plunged more than 100 feet to the bottom of the quarry. Playing at such sites may seem like harmless fun, but every year dozens of children and adults are seriously hurt or fatally injured while playing on active and abandoned mine property. These accidents sometimes happen in traditional mining areas like the coal fields of Appalachia and the remote areas of the west. But the threat is anywhere there are active or abandoned quarries, sand and gravel pits, underground mines, or other mining operations.

Aug 1, 1999

By Launa G. Mallett, Charles Vaught, Michael J. Brnich

Beginning in 1991, scientists at the Pittsburgh Research Laboratory recorded interviews with individuals who are recognized as experts in mine emergency response. These 30 veterans related stories and observations from events experienced during as many as 47 years of response activities. Overall, the response veterans averaged 29 years of mine emergency response experience and 35 years of mining experience. Interviewees included representatives from mining companies, the United Mine Workers of America, and State and Federal agencies. Most of their comments dealt not so much with technical aspects of particular mine emergency responses, but rather the human side of more general topics, including preparedness, experience, people on-site, mine rescue teams, and decision-making. An analysis of their interviews provides an overview of lessons learned on-site at some of the largest mine disasters since the mid-1940s. This knowledge was gathered so that it could be provided to today&apos;s miners and to tomorrow&apos;s emergency response personnel. It is expected that the collective wisdom obtained can be used to help train new responders and guide those decisions that will have to be made on the scenes of future events.

Jan 4, 2004

By William Wiehagen

This trainer?s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators? manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer?s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee?s knowledge and skills and (2) the trainer?s experience in conducting skills training. The ?Skill Check? section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of ?teachable moments? where significantly new knowledge and skills can be learned.

Aug 1, 2006

By Doug Tesarik

The study of neutrinos?particles infinitesimally smaller than atoms?would be significantly advanced if a deep underground facility were available that would filter out unwanted cosmic radiation. Encouraging progress has been made in satisfying the criteria for such a facility with the selection of the Homestake Mine in Lead, SD, by the National Underground Laboratory Committee as the recommended site for a National Underground Science Laboratory (NUSL). The Homestake Mine is America?s oldest and deepest underground mine, and its well-maintained infrastructure to depths of 2438 m below the surface makes the mine an excellent site for such a laboratory. The investigation reported here is an initial study of the stability of the first of the proposed chambers. A cylindrical room with a dome-shaped roof and floor was analyzed in three dimensions using the finite-difference program FLAC3D. The results were compared to recommended support requirements based on Barton?s Tunneling Quality Index, Q. Based on model results and observations from previous mining studies, large rooms with 50-m roof spans can be constructed and will remain stable at 2141 m below the surface in the Poorman Formation when the rock is reinforced with cable bolts. Construction may be possible at lower levels in the Yates Formation if more extensive laboratory strength tests confirm initial results.

Jan 1, 2002

To identify the most successful methods now in use for controlling respirable dust in longwall mines using double-drum shearers. Approach Conduct dust surveys at six longwall mining sections that use double-drum shearers and are regularly in compliance with the Federal Respirable Dust Standard, to identify effective dust control techniques. The selection of mine sites was based on recommendations provided by the Mine Safety and Health Administration. Instantaneous and short-term gravimetric instrumentation make it possible to isolate longwall dust sources and to determine the effectiveness of dust control techniques. (These procedures were developed by the Bureau of Mines, and are described in detail in Technology News Bulletins 134 and 135.) Production levels, and seam heights at each of the six longwall sections were: 53", 700 tps; 60", 800 tps; 72", 1000 tps; 79", 1500 tps; 84", 2000 tps; 96", 1500 tps. Survey Results Three effective dust control techniques were identified. 1. Shearer Operators on Intake Side of Lead Drum-At all mines surveyed, an important factor in controlling dust exposures at the shearer is the use of a cut ting sequence that allows the shearer operators to work most of the time on the intake air side of the lead drum. Dust profiles, like those plotted from data at two mines (see the graphs), show the large gradient in dust concentrations that can

Jan 1, 1982

Develop a reliable, portable device for non-destructively testing the support integrity of a friction rock support (commonly referred to as a Split Set ). Approach The friction rock support, used to support mine roof and ribs, is a slotted tube driven into a drilled hole of smaller diameter. Upon installation, the tube is compressed radially. The amount of compression is a function of the hole diameter, the strength of the host rock, and the properties of the split set itself. A simple lightweight self-contained device was developed to determine the pull-out resistance of the friction rock supports in-situ, based on measurements of the tube&apos;s deformation. The tester measures the com-pressed internal volume of the slotted tube, which has been found to provide an estimate of the support&apos;s resistance to pull out. How It Works The tester consists of a pump and expander sections. The expander sections are made from an elastomer membrane which is stretched over two cores, each one inch in diameter and twelve inches long. The expanders are connected by a flexible coupler so that they can fit any alignment of the support.

Jan 1, 1984

Develop a technology for producing high-quality hake graphite from the steelmaking waste known as kish. Approach Treat the waste kish as an ore and apply mineral processing techniques of physical beneficiation and chemical purification to produce a range of graphite products com¬petitive with the natural mineral. Background Graphite is a naturally occurring form of carbon with a unique combination of properties that make it indispensable in a very wide range of industrial and consumer applications. It has high electrical and thermal conductivity and remains stable to extremely high temperatures It has a low coefficient of friction and is nearly impervious to corrosion. The steel industry is dependent on graphite in clay-, magnesia-, and alumina-bonded refractories for crucibles, bricks, facings, and coatings. Electrical uses include graphite brushes in motors and generators, and electrodes in batteries. The transportation industry needs graphite for clutch and brake linings, and all industries depend on graphite in seals, gaskets, lubricants, and coatings. The consumer sees graphite in composite plastics and in the common pencil. As with all natural minerals, the availability of graphite is diminishing and costs are rising as quality decreases.

Jan 1, 1993

By F. L. Klinger

CRUDE OIL refining continued to be the foremost industry of Bahrain in 1963. This island, the largest of a group 30 kilometers off the Saudi Arabian coast, is the site of the first petroleum discovery in the Persian Gulf and in the Arabian peninsular region. The island&apos;s only oilfield was discovered in 1932; exports of crude began in 1934 and the refinery was built in 1936. Although its crude oil has been less than 1 percent of annual Middle East output in recent years, Bahrain has been an important refining center for many years, processing a substantial portion of Saudi Arabian petroleum as well as all local production. The Bahrain refinery annually accounts for 17 percent 0 the petroleum products produced in the Middle East and 25 percent of the exports. Bahrain&apos;s mineral resources consist of oil, gas, and basic construction materials. Petroleum production and refining are the important mineral industries and contribute most of the national income by payments for taxes, wages, and local services including construction and material supply. The petroleum industry has supported a large share of local business and extensive indirect employment, and its early establishment also helped Bahrain to strengthen its position as a trading center in the Persian Gulf. The country&apos;s entrepôt trade produces about 20 percent of Government revenue, and Bahrain is somewhat less dependent on the petroleum industry than are the neighboring States to the west.

Jan 1, 1964