Search Documents

By Theodore L. Turner

This Bureau of Mines report describes calcination of kaolinitic clay in a direct-fired 2-1/2- by 24-ft rotary kiln at 750° and 775° C. Methods for preparing kaolin feed materials and characterization of calcined products are discussed. Approximately 99 pct of the alumina in a typical eastern Georgia kaolin was soluble in HC1 after calcination at either 750° or 775° C.

Jan 1, 1982

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the quantitative procedures that have been developed for the mine-specific analyses of accident/injury experience data are presented and their applications are demonstrated in a summary form through case study examples. The quantitative procedures will aid mine safety management personnel to develop focused accident prevention strategies including training, as well as to justify the investment in such proactive programs through cost-benefit analyses.

Jan 1, 1993

By W. E. Cassan, W. L. Eaton, James Westfield, W. M. Romisher, Karl Hughes, S. H. Ash

"INTRODUCTION Funds were made available to the Bureau of Mines, United States Department of the Interior, for anthracite investigations during the fiscal year ended June 30, 1945. One of the approved projects was to conduct inquiries and scientific and technologic investigations having a bearing on the anthradite mine-flood problem. The investigative work done from July 1,1944, to June 30, 1946, is described in previous reports (5, 8, 10, 24, 28). 6/Purpose of Report The purpose of this report is to describe the investigative work conucted by the Anthracite Food-Prevention Section, Safety Branch, Bureau of Mines, during the period July 1, 1946, to June 30, 1947,Scope of WorkInvestigative work during the fiscal year ended June 30, 1947, was conducted under the direction of D. Harrington, chief, Health and Safety Division, and S. H. Ash, chief, Safety Branch, Bureau of Mines, Washington, D. C.The broad objective of the investigative work was to obtain factual day on: 1. Anthracite reserves of Pennsylvania.2. Underground water pools.3. Barrier pillars.4. The ""buried valley"" of the Susquehanna River.5. Infiltration of surface water into underground mine workings.The above-mentioned investigations are being continued during the fiscal year July 1, 1947, to Juno 30, 1948.In addition to the investigative work covered in this report, Ash end Eaton presented a paper on barrier pillars, which proposes a method for designing barrier pillars and has been Published by the American Institute of Mining and Metallurgical Engineers (5);"

Apr 1, 1948

By Carl R. Peterson

Development of reliable, portable, low headroom, hard rock crushers would improve the efficiency of most currently operated conveyor systems and make it possible to bring conveyor haulage closer to the face, thus eliminating expensive rock rehandling procedures. A crusher that could be easily moved would permit the more widespread use of lower cost haulage systems, such as conveyors, to transport the ore out of the mine. Such crushers would be installed close to the working areas, resulting in an optium haul from the face to the dump location. A recent contract study by Rapidex, Inc., "Application Study of Portable Underground Hard Pock Crusher" (USBM Contract No. J0265006) provides a survey of industry needs in portable underground crushing, together with conclusions and concepts as to specifications and type of crusher required to serve the greatest number of operations. To fill this need a three phase program has been undertaken by the Bureau of Mines: Phase I - Design: Phase II - Construction and Testing, and Phase III - Production Underground Test. This report covers Phase I only, and includes the complete engineering design and specifications of the Rapidex Rotary Jaw Crusher conceived in the earlier "Applications Study". Also included are the design, construction, and testing of a quarter-scale functional model, utilizing three different types of rock and two different crusher feeder systems.

Jan 1, 1978

By D. J. Dollhopf

An overburden handling dragline operation was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to determine the degree a dragline could mix overburden inhibitory zones during the spoiling process. In order to quantify the mixing process the overburden was: 1) scatter spoiled; 2) dump spoiled; and 3) spoiled in a normal manner. This demonstration was part of an effort to investigate means of reestablishing non-polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. When inhibitory material constituted < 5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. Inhibitory overburden zones often reappeared at the base or top of spoil piles in the potential aquifer and root zones suggesting the need for selective placement procedures. Scatter spoiling did not appear to be significantly more effective than normal spoiling, however clump spoiling seemed to produce less mixing of inimical zones. Mining activity has reduced ground-water levels within 1600 m of the active pit. The aquifer which is developing in spoils appears to have similar confinement characteristics as those that existed in the premined aquifer. To date no definite trends have been observed concerning changes in surface or ground-water chemistry associated with mining.

Jan 1, 1978

By K. Thirumalai

This study forms a part of Bureau of Mines continuing research on thermal fragmentation of rocks. The potential of internal heating techniques for rock fragmentation is discussed. A concept of rock fragmentation with rapid inter¬nal heating of a localized inner volume of rock is advanced The energy required for rock fragmentation is made available by creating a required vol¬ume of localized heating. The fragmentation of rock using the proposed method is analyzed and qualitatively compared with the results of experiments with Charcoal granite, Dresser basalt, and Sioux Quartzite. High frequency dielec¬tric heating below 100 MHz is used in the study as an example to examine the working of the concept. The selection of operating conditions for the experi¬mental heating is explained. Fragmentation of Charcoal granite and Dresser basalt test rock blocks is achieved for localized heating below 550° C. The heated volume required for fragmentation is observed to be less than 2 percent of the test block volume and the electrical energy consumption is in the order of 3.5 to 6 5 kwhr/m3 The method offers a possibility for in situ fragmenta¬tion of rocks, favorable for internal heating. The method is highly dependent on rock properties governing internal heat generation The efficiency of dielectric heating in the experimental study is observed to increase with increasing dielectric loss of the rock material, ranging from about 10 percent in Sioux. Quartzite to about 50 percent in Dresses basalt

Jan 1, 1970

By James P. Ulery

Explosions in U.S. coal mines have caused death and injury to miners and destruction of workings since the first reported explosion in 1810. These explosions are caused when buildups of explosive gas and/or dust in the mine are ignited by the presence of a flame or spark. Methane gas is inherently generated and held by adsorption in coal and is normally liberated during mining. Because this gas is explosive in the range of 5%–15% by volume, fresh air is constantly supplied to the working face to prevent the methane/air mixture from reaching this explosive range. The required amount of ventilation air is based on estimates of gas release under normal conditions. Occasionally, unanticipated and unusually high emissions are encountered, which, despite normal ventilation controls, result in an explosive mixture that a spark from a cutting bit or electrical equipment can easily ignite. Investigations have shown that such emissions are often associated with anomalous geologic features or conditions. Although most operators are aware that certain geologic features may adversely affect productivity, few are aware of their potential as a gas emission hazard. This report presents a historical framework detailing the impact of geologic features on excess gas emissions and resultant mine explosions. It also provides operators with specific information on recognizing and alleviating potential hazards from methane emissions related to these geologic features.2

Jan 4, 2008

By J. T. McCartney

OPTICAL PROPERTIES of U.S. coals of differing rank have been investigated by the Bureau of Mines, for about 20 years. These investigations have been remade to further the development of an objective basis for petrographic analysis of coal and to add to knowledge of the structure and composition of coal and coal components by determining their optical constants in various regions of the electromagnetic spectrum. Various experimental techniques have been used in these studies, including determination of reflectance from bulk specimens and transmittance of thin and ultrathin sections, interferometry, electron microscopy, and election diffraction. Similar studies leave also been made of graphite, the end product of coal metamorphism. The bureau of Mines conducted the first U.S. investigation of reflectance properties of coal components, laying the foundation for petrographic analysis based on arbitrary reflectance classes and for automated reflectance analysis of coals. Optical constants of coals of differing rank and of graphite have been determined in the ultraviolet-visible-near infrared spectrum. Maxima in the optical constants of graphite were observed in the ultraviolet region and were interpreted to be related to transitions of electrons between the valence and conduction bands. Similar maxima for coals, especially high-rank coals, appeared to be characteristic of the presence of graphitelike layers. A special application of optical theory to absorbing, anisotropic materials like graphite and high-rank coals has been developed. Electron microscopic and electron diffraction studies of coals have revealed various ultrafine structures in coal components and have shown the evolution of an oriented, crystalline graphite structure in high-rank coals.

Jan 1, 1967

By Patrick J. Coleman, John C. Kerkering

Problem: Mining in the United States remains one of the most hazardous industries, despite significant reductions in fatal injury rates over the last century. Coal mine fatality rates, for example, have dropped almost a thousand fold since their peak in 1908. While incidence rates are very important indicators, lost worktime measures offer an alternative metric for evaluating job safety and health performance. The first objective of this study examined the distributions and summary statistics of all injuries reported to the Mine Safety and Health Administration from 1983 through 2004. Over the period studied (1983 2004), there were 31,515,368 lost workdays associated with mining injuries, for an equivalent of 5,700 person years lost annually. The second objective addressed the problem of comparing safety program performance in mines for situations where denominator data were lacking. By examining the consequences of injuries, comparisons can be made between disparate operations without the need for denominators. Total risk in the form of lost workday sums can help to distinguish between lower and higher risk operations or time periods. Method: Our method was to use a beta distribution to model the losses and to compare underground coal mining to underground metal/nonmetal mining from 2000 to 2004. Results: Our results showed the probability of an injury having 10 or more lost workdays was 0.52 for coal mine cases versus 0.35 for metal/nonmetal mine cases. In addition, a comparison of injuries involving continuous mining machines over 2001 2002 versus 2003 2004 showed that the ratio of average losses in the later period to those in the earlier period was approximately 1.08, suggesting increasing risks for such operations. Discussion: This denominator free safety measure will help the mining industry more effectively identify higher risk operations and more realistically evaluate their safety improvement programs. Impact on Industry: Attention to a variety of metrics concerning the performance of a job safety and health program will enhance industry&apos;s ability to manage these programs and reduce risk.

By Rudolf E. Greuer

The existing computer programs for the simulation of ventilation systems under normal ventilation conditions are reviewed and a suitable program for including the influence of mine fires is selected. New program parts are written for the consideration of methane productions in coal mines, heat and gas productions of mine fires, temperature and air composition changes in ventilation systems, and the ventilation forces resulting from the latter. Other program parts are provided for the detection of danger zones and reversed air currents and for the inclusion of recirculated air currents in the network analysis. Existing program and new program parts are combined. The resulting new program can be used for a multitude of assignments. It is designed for the practical ventilation engineer and should be applicable to all types of ventilation emergency plans, in particular mine fire plans. The organization of the program and its mathematical basis are described. A FORTRAN IV listing and several flow diagrams are included. Eight executed examples are discussed, input and output for these examples explained. Storage requirements and execution times are estimated.

Jan 1, 2011

By Theresa Y. Schulz

It is interesting to study the noise standards that have been promulgated in the US over the last decade or so. These regulations are likely to have long-lasting impact. The Occupational Safety and Health Administration (OSHA) Hearing Conservation Amendment (March 1983) continues to have influence not only in the workplace but in the debate over new regulations. Both the Mine Safety and Health Administration (MSHA) and Federal Railroad Administration (FRA) regulatory preamble documents state the desire to be consistent with OSHA. An examination of Table 1, which compares the major components of the three regulations and the 1998 NIOSH “best practices” criteria, depicts the extent to which that intent is met. There has been some regulatory activity in the last decade which may give some hope for evolution and updating based on the wealth of science that has occurred during the last quarter of a century since the OSHA regulation was enacted. However there has also been some “back-sliding” toward more lenient standards. The MSHA noise standard made regulatory progress in September 2000 by emphasizing engineering and administrative controls, followed by personal protective equipment, in the hierarchy of noise intervention. MSHA’s requirement for technician certification (today only available from CAOHC) strengthened the training requirements for audiometric testing in hearing conservation programs and MSHA also added the requirement of dual hearing protection at 105 dB TWA. There were many subtle differences between OSHA and MSHA based on comments and a desire to clarify some of the vague aspects of the OSHA noise standard, and meet the needs of the regulated mining industry. One example pertains to the ceiling for exposures. OSHA says, “no exposures >115 dBA,” which is interpreted to mean no unprotected exposures above that level, giving credit for the assumed effectiveness of hearing conservation programs, hearing protection devices and administrative and engineering controls. MSHA specified that a “P” code1 violation be issued for any protected or unprotected exposures >115 dBA. The Federal Railroad Administration (FRA) noise standard for railroad operating employees, which went The Modern Evolution of Hearing Conservation Regulationsinto effect February 26, 2007, was expressly based on the OSHA standard but also uses MSHA for comparison. The preamble states that the FRA defers to OSHA as the “primary regulator of noise in the workplace,” but also acknowledges the need for some departure from the OSHA regulation (FRA Preamble II.B). As an example, FRA requires testing at 8000 Hz “because it will allow employers to identify hearing loss sooner.” The FRA rejected MSHA’s hierarchy of noise controls in favor of requiring specific engineering interventions and focusing on appropriate hearing protection which would still allow communication and audibility, and identification of excessive noise through employee-filed “excessive noise reports.”2 Where OSHA has no specific mandate requiring employees to take advantage of the employer-paid audiogram, it has been traditionally a condition of employment and is generally accepted that OSHA-covered workers require an annual audiogram. MSHA addressed this issue in its preamble; however, they made no significant change. MSHA employers are required to offer annual audiograms but MSHA stopped short of requiring employees to comply with annual audiometric testing. The MSHA preamble does allow that mine operators can also make audiometric monitoring a condition of employment. FRA requires employees to

By H. H. Schrenk, W. P. Yant, F. A. Patty

"INTRODUCTION In accordance with the outline of investigation described in a previous report 5 of the Bureau of Mines dealing with the use of acrolein for detecting leakage of methyl chloride from unit--type refrigerating systems, the work has been extended to include an investigation of its use in a multiple system, This report gives the results of analysis of samples of the gas from representative units of a multiple system charged with methyl chloride containing approximately 0.9 per cent acrolein by volume, The results furnish a basis for estimating the Warning that would be given in event of leakage. The properties and warning intensity of acrolein have been described in a previous report. 5 ACKNOWLEDGMENTSThis investigation was made at the combined request-of Several Inc., Manufacturers of refrigerating, appliances, and the Roeasler Hasslacher Chemical Co., manufacturers of methyl chloride. Acknowledgment is given to R. M. Major, ,chief chemist of the former firm for arranging the experimental site and equipment; to Arthur O. Haseeneall, owner of the apartment building where the investigation was conducted, for his courtesy in permitting the investigation; and to R. R. Sayers, chief surgeon, Bureau of Mines, and surgeon., U. S. Public Health Service, for suggestions and advice."

Sep 1, 1930

By J. R. Ross

A reconnaissance for sources of scandium and a metallurgical investigation of recovery methods for byproduct scandium from uranium mill solutions were conducted by the Bureau of Mines. The work on scandium was undertaken to obtain information on domestic resources and to explore and develop recovery procedures in consonance with the Bureau&apos;s long-range program for conservation and wise utilization of mineral resources. The element scandium is widely distributed in the earth&apos;s crust in trace amounts, but it seldom occurs as an important constituent in any mineral. An exception is thortveitite, (Sc,Y)2 Si207) a rare mineral that contains various amounts of scandium and yttrium and may contain up to 42 percent scandium oxide (SC203). Knowledge of the chemistry of scandium has expanded rapidly in recent years (1, 4, 9)4 but only fragmentary information is available about the metal because it is still largely a laboratory curiosity without established uses (2, 3). A recent study shows some of the physical proper-ties of the metal are (1) density of 3.05 grams per cubic centimeter) (2) melting point of 1,540° C, (3) hexagonal close-packed structure) (4) hardness of about 50 Brinell (500-kilogram load), and (5) an alloy behavior similar to yttrium and rare-earth metals (2). The price of $2,850 a pound for scandium oxide of 99.9 percent purity and $2,700 a pound for oxide of 99 percent purity reflects the scarcity and complex chemistry of the element.

Jan 1, 1962

By Eugene H. Skinner

This Bureau of Mines report describes the fieldwork and subsequent analysis to determine physical properties, stress distribution, and several aspects of rock behavior as a necessary evaluation for a typical mine opening. All work was done at a test site on the 3300 level, Crescent mine, Coeur d&apos;Alene mining district, Idaho. Free field stress beyond the influence of the opening was also determined. Conventional overcore technique with the three-component borehole deformation gage developed by the Bureau of Mines was used in three drill holes. Three field verification tests were performed using a gage newly developed by the Spokane Mining Research Center in an approach herein termed "initial deformation method." Use of this method validated that aspect of overcore theory which predicts that similar deformation effect occurs in the wall rock around the perimeter of an opening in rock under stress. Also described are all drilling procedures and performances. Physical property determinations were made on rock samples obtained from the three overcore drill holes. Twelve physical properties with a total of [532] values were obtained at various drill hole orientations and depths. Exhaustive statistical tests were utilized in the analysis of these physical properties. Further elaborated are statistical inferences based on these analyses. Extensive analysis and interpretation of Crescent mine geology are also described.

Jan 1, 1974

By G. L. Fitzpatrick

A portable optical instrument for performing multispot laser vibrometry is described. The instrument is capable of measuring arrival times, surface motion frequency, and surface velocity and displaying these quantities in various useful ways. Sigma Research is currently pursuing the development of such optical measuring systems for the evaluation of structures in rock by non-contact interferometry methods. This work was sponsored by the U.S. Department of Interior (U.S. Bureau of Mines) under a Small Business Innovation Research (SBIR) contract number J0145075. The goal of the work was to develop a portable tripod mounted measuring system which can be set up at arbitrary distances (up to 30 meters) from a surface and project four in-line laser sample beams on this surface. A light receiving telescope gathers the scattered light from these four spots and provisions are made to mix this light with a reference beam from the laser. Four photodiodes are employed to determine the resultant interference signals which characterize the motion (particle velocity, frequency, amplitude) of the four illuminated spots on the surface under sudy. Information of this type can then be used to characterize the elastic or mechanical properties of the surface in question. In some cases (if more than four spots are involved) this surface information could be back propagated to draw inferences about the internal state of the material volume bounded by this surface.

Jan 1, 1987

By G. R. Peterson

To determine the availability of lead and zinc from demonstrated resources, the Bureau of Mines evaluated 235 mines and deposits in 31 market economy countries. Of the 235 mines and deposits evaluated for this study, 186 were evaluated as zinc operations, 30 as lead operations, and 19 as copper operations. Demonstrated lead-zinc resources of market economy countries in 1981 were approximately 4.3 billion metric tons (t) of ore containing 221 million t of zinc and 97 million t of lead. Of these amounts, approximately 154 million t of zinc and 70 million t of lead are estimated to be recoverable. The analyses indicate that demonstrated resources in market economy countries should be sufficient to satisfy projected demand for primary lead and zinc through the balance of the century. The U.S. lead industry will continue to have a comparative advantage over the rest of the world industry, barring any drastic increase in the cost of compliance with pollution control regulations. It appears that the comparative disadvantage faced by the U.S. zinc industry will probably intensify owing to the relative quantity of lower cost zinc resources in other countries, especially Canada, Australia, Mexico, and Peru.

Jan 1, 1985

By Arnold M. Lansche

DOMESTIC OUTPUT of white arsenic, As2O3, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. Arsenic metal was not produced. Consumption, and Uses.-Most of the white arsenic produced in 1964 was consumed in manufacturing lead and calcium arsenate insecticides. In the 12 year period since 1951 the production of lead arsenate insecticide has varied between 7,800 tons and 4,900 tons, indicating that lead arsenate has maintained its position in competition with organic insecticides.

Jan 1, 1965

By J. Kruttschnitt

This paper, describing the mining operations at Mount Isa Mines, is one of a series covering mining methods and costs being published by the United States Bureau of Mines. The Mount Isa property has been in operation since June 1931; during this period operations have changed from the production and treatment of carbonate ores to the mining, milling, and smelting of sulphide ores. This change involved revision of ore-extraction methods. Stoping methods have been designed to apply to parallel lodes ranging from 10 to over 100 feet in width and dipping at 50° to 60°. The hardness and strength of the ore and enclosing wall rocks, together with the strength and thickness of the country rock between lodes, have permitted the selection of a sublevel stoping method for mining the sulphide ores.

Jan 1, 1937

By Sam S. Taylor

The disposal of oil-field brines by injection into subsurface formations other than fresh-water-bearing strata is a positive method of eliminating the harmful effects of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. The methods used most generally for the disposal of brines produced with oil are (1) impounding in evaporation ponds, (2) controlled diversion into surface streams, and (3) injection into subsurface formations. Various States recognize one or more of the methods as legally authorized procedure. As a general rule, impounding brine in ponds and solar evaporation have not been entirely successful, principally because of the large volumes handled; the porous nature of the soil, and the low rate of evaporation. Likewise, the diversion of brine into freshwater streams by controlled dilution has not proved satisfactory in some areas, especially in parts of Kansas and Oklahoma where the rainfall is relatively low, because it has been impossible to obtain enough fresh water for such dilution.

Jan 1, 1939

By D. J. Hawk

The mechanical properties of coal are often represented by the orthotropicmaterial model, which consists of nine elastic constants. The material symmetries involved are found in coal primarily because of the natural process by which it was formed. In this thesis the material properties of five U.S. coals, as obtained from cubical testing, are examined, using as a basis for comparison the assumption of the orthotropic material model. An analysis is performed on each set of coal material data in order to examine its conformability to other, less complex material models, these being the transversely isotropic model consisting of five elastic constants and the &apos;isotropic model consisting of two elastic constants. In addition, the material properties of two American shales are analyzed, based on the assumption that they comply with the transversely isotropic model. An analysis similar to that performed on the coal material is applied to the shale in order to determine the conformity of its material properties to the isotropic model.

Jan 1, 1980