Search Documents

By Alice V. Peter

Meerschaum or sepiolite is employed principally in tobacco pipes and cigar and cigarette holders, although a few other uses of minor importance are Down. The unique value of a meerschaum pipe is derived from the owner's pleasure in watching the color deepen with smoking and in having the color "set" at the desired shade. The name "meerschaum" (German for "sea foam") is applied because the material, when pure and dry, will float on water. Owing to its resemblance to the porous, bonelike structure of the cuttlefish, or septa, it is also known as sepiolite. There are a few scattered deposits of meerschaum in. the United States which have yielded a small product ion, but the world's supply of the' material is obtained fined principally from Asia Minor, Meerschaum deposits near Eski-Shehir, Turkey, are said to have been worked 2,000 years ago, but commercial exploitation is a development of the last hundred years DESCRIPTION AND PROPERTIES Meerschaum is a hydrous magnesium silicate (H4Mg2Si3010) having the following theoretical analysis: Si02, 60.8 percent; MgO, 27.1 percent; H20, 12.1 percent. It is a soft. (H.2 - 2.5), fine-grained, earthy, white, gray, or yellow material. It is very light weight when pure (specific gravity, 1 to 2) and is highly absorbent. Because of its porosity the proportion of water present in the mineral is affected by the humidity'of the atmosphere. In a moist atmosphere the water content may be as much as 21.7 percent. Then wet the material is soft and somewhat plastic. When dried again it becomes lard and tough. The toughness is especially apparent in some forms that have a fibrous or leathery texture.

Jan 1, 1934

By Charles L. Kimbell

In 1990, the aggregate value of world international export trade in mineral commodities was estimated at more than $64 billion in current (1990) dollars, about 8.4% higher than that in 1989, but still 8.7% below the record high set in 1980. Table 8 provides a data series for the estimated value of world export trade in all mineral commodities from 1979 through 1990, as well as a breakdown of this total into fuel and nonfuel commodities. It is noteworthy that for this 1990 edition, trade data for the year of review were available in time for inclusion, whereas in previous editions, the latest available global trade data were for the year prior to the year of review. Hence, as regards trade, this edition of Minerals in the World Economy updates the 1989 edition by 2 years rather than by only 1. For this reason, it is appropriate to note that the 1989 global total value for inter-national export trade in mineral commodities was almost $596 billion, 11.1 % above the revised 1988 level of more than $536 billion, both figures expressed in current dollars for the appropriate year. Despite the considerable increase in the dollar value of mineral commodity exports, their share of total export merchandise trade declined to 19.1 % in 1990 from 19.7% in 1989. At 19.1%, this share was very near the recent year record low of 19.0% reached in 1988. The year 1990 was the fourth in a row in which the total value of world mineral commodity export trade increased.

Jan 1, 1993

By M. B. Cooke, A. D. Bauer, E. W. Dean

The Bureau of Mines is collecting and analyzing representative samples of crude petroleum from all the producing fields in the United States , and the results are being published in a series of reports that are preliminary to the issue of a bulletin covering the entire survey . The bureau has recently completed a survey of crude oils from the Kansas district . In all 27 samples were collected and analyzed , under the direction of A. W. Ambrose , chief petroleum technologist of the Bureau. Valuable assistance was received through the cooperation of oil companies operating in the State , especially the Prairie Pipe Line Co. , and the Empire Pipe Line Co. The present report issued as Serial 2322 , on the Kansas crudes , forms the fifth of the series . Of the four previous papers , the first ( No. 2202 ) deals with crudes from the Eastern fields of the United States , the second ( No. 2235 ) with crudes from the Rocky Mountain district , the third ( No. 2290) gives additional data , cn viscosities and pour tests , for the crudes from these two fields , and the fourth ( No. 2293 ) covers the fields of northern Texas , northern Louisiana , and Arkansas . The details of the methods of collecting samples , making laboratory tests and interpreting results , have been discussed in these earlier reports . It has also been pointed out that the only adequate method of interpreting analyses of crude oils is to compare the individual reports with the analysis of some crude oil that is familiar to the operator . For this reason , no comprehensive discussion of the results of the Kansas survey is attempted, although some general statements may be made .

Feb 1, 1922

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with the intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page, Linda J. McWilliams, Gerald J. Joy, Steven E. Mischler, Jon C. Volkwein

The United States National Institute for Occupational Safety and Health, through an informal partnership with industry, labor, and the United States Mine Safety and Health Administration, has developed and tested a new instrument known as the Personal Dust Monitor (PDM). The new dust monitor is an integral part of the cap lamp that coal miners normally carry to work and provides continuous information about the concentration of respirable coal mine dust within the breathing zone of that individual. Previous laboratory testing demonstrated that there is a 95% con?dence that greater than 95% of individual PDM measurements fall within ±25% of reference measurements. The work presented in this paper focuses on the relationship between the PDM and respirable dust concentrations currently measured by a coal mine dust personal sampler unit utilizing a 10 mm Dorr Oliver nylon cyclone. The United Kingdom Mining Research Establishment instrument, used as the basis for coal mine respirable dust standards, had been designed speci?cally to match the United Kingdom British Medical Research Council (BMRC) criterion. The personal sampler is used with a 1.38 multiplier to convert readings to the BMRC criterion. A strati?ed random sampling design incorporating a proportionate allocation strategy was used to select a sample of mechanized mining units representative of all US underground coal mines. A sample of 180 mechanized mining units was chosen, representing approximately 20% of the mechanized mining units in production at the time the sample was selected. A total of 129 valid PDM/personal sampler dust sample sets were obtained. A weighted linear regression analysis of this data base shows that, in comparison with the personal sampler, the PDM requires a mass equivalency conversion multiplier of 1.05 [95% C.I. (1.03, 1.08)] when the small intercept term is removed from the analysis. Removal of the intercept term results in a personal sampler equivalent concentration increase of 2.9% at a PDM measurement of 2.0 mg m-3.

By R. Karl Zipf

MULSIM/NL (multiple scams, nonlinear) is a three-dimensional boundary-element method (BEM) program developed at the U.S. Bureau of Mines for stress and displacement analysis of coal mines and thin metalliferous veins. It can analyze one to four parallel seams that can have any orientation with respect to the Earth's surface. Three main new features distinguish MULSIM/NL from its predecessors: (1) nonlinear material models, (2) multiple mining steps, and (3) energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material: (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. Detailed checks show that numerical stress and displacement calculations compare well to known analytic solutions for simple problems. The total energy release calculated by MULSIM/NL is comprised of three basic terms: (1) strain energy release from the mined-out material, (2) linear kinetic energy release due to change in gravitational potential over the mined-out area, and (3) nonlinear kinetic energy release due to nonlinear materials in the total backfill and gob area. The strain energy release term is modified to account for nonlinear stress-strain behavior in the unmined materials. Comparisons of these numerical energy release rate calculations with known analytic solutions show excellent agreement.

Jan 1, 1992

By John J. Sammarco, Janet S. Flynt

This report (Independent Functional Safety Assessment Guidance 7.0) is the last in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and after-market suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 4, 2006

By S. B. Levin

"INTRODUCTION An exposure of large beryl crystals in pegmatite on Beryl Mountain, in Sullivan County, N. H., was the basis for investigation by the Bureau of Mines to determine the extent of the beryl mineralization and to expose other parts of the same zone that were favorable for additional beryl-rich shoots. Testing by surface cuts, trenching, and tunneling was conducted by the Bureau of Mines from August to December 1943.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and makes beneficiation tests. The field work was supervised by Paul M. Tyler, regional engineer, and John D. Bardill, district engineer. S. B, Levin was in direct charge of the project.LOCATION AND ACCESSIBILITYThe deposit is on the northeast slope of Beryl Mountain, 1 mile south of the village of South Acworth. The village, on State Highways 101 and 123a, is 12 miles northeast of Bellows Falls, Vt. The deposit is reached from South Acworth over a gravel-surfaced road and about 1,000 feet of good truck trail (fig. 1).The nearest railroad siding is at Cold River, on the Boston & Maine Railroad, where there is also a fairly modern, but now idle, feldspar mill."

Mar 1, 1948

By Herbert R. Appell

Urban refuse, cellulosic wastes, and sewage sludge have been converted to heavy oil by heating under pressure with carbon monoxide and steam. Conversions of the organic matter to oil, water, and gas have averaged near 90 percent at temperatures of 250° to 400° C and pressures of 1,500 to 5,000 psi. The yield of oil, based on the dry organic matter of the waste materials, is usually near 40 percent. This is the equivalent of more than 2 barrels of oil per ton of dry, ash-free waste material. The oil from urban refuse and cellulosic wastes has a sulfur content near 0.1 percent. This low sulfur content makes the oil from refuse a desirable source of fuel oil.

Jan 1, 1970

By BUREAU OF MINES

The Bureau of Mines, in its investigations of respiratory apparatus for use in mines and allied industries; tests equipment that is voluntarily submitted by manufacturers in accordance with published schedules of tests. These tests are designed to insure that the equipment has the minimum requirements for safety in use. Approval certificates are issued for apperatus that meets the bureau's specifications, and the manufacturer is permitted to mark his equiment with a seal showing that it has been approved as "Permissible." A complete list of per- missible self-contained oxygen breathing apparatus, gas masks, and hose masks tested prior to January 1, 1930, was published in Bureau of Mines Information Circular 62309. The present list includes all equipment tested and approved prior to July 1, 1930.

Sep 1, 1930

By C. C. Merrill

Columbium, tantalum, titanium, and zirconium are present in solid waste products generated by the chlorination of rutile used for production of titanium tetrachloride (TiC14). The columbium and tantalum were separated from titanium and zirconium by liquid-liquid extraction techniques using a secondary amine. Salts of these elements are in a leach liquor produced by water leaching of mineral waste from the chlorination of rutile. This waste, produced at the rate of approximately 50,000 tons per year, is about 40 wt pct water soluble. Leach liquors, separated by filtration, were further separated into a solid fraction and a liquid fraction by pressure hydrolysis, The solid fraction containing Cb, Ta, Ti, and Zr was dissolved in HC1-HF and used as a feed solution. Columbium and tantalum were removed from the organic extractant with 1 [N] HC1. A miniature 10-stage reactor showed that the columbium and tantalum present in solution could be separated with a continuous flow.

Jan 1, 1972

By John W. Adams

The present status of the National Bureau of Standards program is that many magnetic tapes of analog data have been recorded in four major mines. Each mine uses different types of equipment. In addition, some surface measurements of noise have been made at two additional mines. Two types of recordings have been made: (1) broadband measurements for spectral plots and (2) narrowband measurements for amplitude probability density (APD) plots. Only data from one mine (Robena #4) has been processed and was, presented at this workshop. The short-term goals are: (1) finish processing data from the other mines, (2) establish or reduce measurement system uncertainties, (3) put Robella report into final form for distribution, and (4) hold a review to determine what has been done, to distribute and to interpret the preliminary data, and to determine what still needs to be done. Long-term goals are: (1) complete final reports on each of the mine trips, (2) establish techniques for predicting noise in mines already visited and establish uncertainty bounds for these predictions, and (3) establish techniques for predicting noise in mines that have not been visited (but that use similar equipment to those visited) and also establish uncertainty bounds for these predictions. Specific factors or formats to be presented include: (A) For underground broadband measurements: 1. 300 Hz to 100 kHz spectral plots 2. 300 Hz to 384 kHz spectral plots 3. 300 Hz to 192 kHz spectral plots 4. 300 Hz to 6kHz (subject to change to 3 or 12 kHz) spectral plots (B) For surface broadband measurements: 1. 300 Hz to 6 kHz (or 12 kHz) spectral plots 2. 300 Hz to 3 kHz spectral plots (C) For underground narrowband measurements : 1. APD plots at 12 frequencies from 10 kHz to 32 mHz of magnetic field strength 2. R. M.S. and average values will be calculated based on time averaging for these plots (D) Sample spectral measurements of: 1. Roof-bolt voltages 2. Trolley wire-to-rail voltages 3. Phone line currents

Jan 1, 1973

By D. J. MacDonald

The Bureau of Mines has carried out investigations on a method for producing zirconyl sulfate solution from zircon sand, comprising (1) reacting zircon sand with molten NaOH, (2) leaching the resultant fusion frit with water to remove sodium silicate and to convert sodium zircon-ate to hydrous zirconium oxide, and (3) leaching the hydrous zirconium oxide from unreacted sand with hot, dilute H2S04 to produce crude zirconyl sulfate solution. The following conditions were found to be suitable: reacting 0.6 kg of NaOH per kilogram of zircon sand for 10 min at 600° C; leaching the frit with 3 to 4 liters of water per kilogram of solids; leaching the residue with 5.1 liters of water and 1.25 liters of 98-pct H2S04 per kilogram of original solids for 10 min at 90° C; and filtering or decanting to recover unreacted zircon sand. A preliminary cost estimate is included.

Jan 1, 1982

By P. R. Bremner

The United States is more than 90 pct dependent on imported bauxite a source for aluminum, but it has vast nonbauxitic aluminum resources, such as kaolinite, anorthosite, alunite, etc. As part of a program to devise processes for treating these resources, the Bureau of Mines investigated a bench-scale leaching process using hydrochloric acid (HC1) and fluoride to extract aluminum from Wyoming anorthosite. HC1 and fluoride-to-aluminum (F/Al) mole ratios were studied with respect to aluminum extraction for single-stage, cocurrent, and countercurrent leaching modes. Using 95 pct stoichiometric HC1 and a F/Al mole ratio of 0.27, 90 pct of the aluminum was extracted by countercurrent leaching. Single-stage leaching with the same amount of acid and fluoride extracted 48 pct of the aluminum. Three fluoride sources, CaF2, Na2SiF6, and H2SiF6, were used and gave similar results on aluminum extractions.

Jan 1, 1982

By Kenneth L. Cashdollar

While underground coal technology has progressed over time, regulations on coal dust have not kept up ? the most recent rules are more than 80 years old. The National Institute for Occupational Safety and Health and the Mine Safety and Health Administration conducted a joint survey recently on coal particle ranges as measured in US coal mine samples. In underground coal mines, dust explosions are prevented by the addition of enough rock dust (usually limestone) to make the total dust mixture inert. The rock dust acts as a heat sink for the dispersed dust mixture by reducing the temperature below the value needed to propagate an explosion. Federal regulations require 65% in combustible content in intake airways and 80% incombustible content in return airways, where the coal dust is assumed to be finer in size. The regulations also require an additional 1% incombustible for each 0.1% methane in the ventilating air in intakes and 0.4% additional incombustible for each 0.1% methane in returns.

Jan 1, 2008

By Wilbur I. Duvall

This report presents experimental data on the propagation of explosion- generated strain pulses in rock. Tests were performed in 5 different rock types, employing 10 different types of explosives. Charge sizes ranged from 0.5 to 50 pounds, and travel distances ranged from 2.5 to 70 feet. Analysis of the data shows that the experimental peak strain data satisfy an exponential decay propagation law of the form: ?R/W1/3 = Ke ?aR/W1/3. For a particular rock, parameter K is a linear function of the calculated detonation pressure or the calculated energy density of the explosive. For a particular explosive, K is a linear function of the elastic parameter of the rock, p2, a result, which is at variance with elastic theory. The absorption constant, a, is independent of type of explosive but dependent upon rock type. However, no definite relation between a and the physical properties of the rock could be established.

Jan 1, 1959

By J. H. Perry, D. W. Houseknecth, C. A. Kertis, A. T. Iannacchione

Major problems facing the development of coal and gas resources of the Hartshorne Coalbeds include the complex distribution of minable and unminable coal, high methane content and bed pressure, faulting, variations in degree of dip, presence of natural gas fields in associated sandstones, and legal problems, caused by local geologic characteris- tics, in identifying gas origin. This Bureau of Mines study provides pertinent geologic information for long-range planning of subsurface coal and gas production from the Hartshorne Coalbeds. Pittsburg, Coal, Hughes, and Atoka Counties, OK, have approximately 1 billion metric tons (1.1 billion short tons) of Hartshorne coal in place. The methane resource of Hartshorne Coalbeds is estimated at 9.2 billion m3 (325 billion ft3) and varies with overburden and rank, These estimates were compiled from gas well density logs, coal-core data, out- crop measurements, abandoned mine maps, and the literature. The Hartshorne Coalbeds represent a valuable coal and gas resource which at present is contributing nothing to coal and gas production. This report discusses potential problems and serves as a reference for future exploration and development work. Recognition of these potential geologically related problems prior to development of this basin will reduce hazards and allow for an economic recovery of these resources.

Jan 1, 1983

By David M. Hyman

The Bureau of Mines has developed two experimental designs for deter- mining the volumes and relative proportions of the various gas species, particularly methane (CH4), occluded in rock salt. To date, the rock salt samples analyzed have been relatively small (400- to 1,000-gram) grab samples from Louisiana Gulf Coast domal salt mines. The results obtained are comparable to results in Polish domal salt mines, in terms of occluded gas volumes per mass of rock salt. The notable difference between the Louisiana and Polish occluded gas mixtures is in the relative proportions of the individual gas species. The two methods used by the Bureau are ballmill crushing and dissolution. Of the two, the dissolution method appears to be more versatile because it can be performed in situ. The relevance and applicability of data on the occluded gas contents of rock salt are dependent on sample size, sample collection method, geologic context of the sample, and the correlation with gas emissions that occur as a result of mining-induced fractures and pressure differentials.

Jan 1, 1982

By F. S. Karn

Measurements were made of the flow of helium, methane, ethane, butane, and toluene through thin disks of coal. All measurements were made on a dense layer in the Pittsburgh seam identified as attritus. Flow increased with pressure differential and temperature. At room temperature and a pressure differential of 1 atmosphere flow rates along the bedding plane of Pittsburgh seam coal were helium 881 X 10-10 cm2 sec-1, methane 1.2 X 10 -10 cm2 sec-1, ethane 0.54 X 10-10 cm 2 sec-1, n-butane 0.35 X 10-10 cm2sec-1, and toluene 3.8 X 10-10 cm2sec-1. Flow rates were 50 percent lower across the bedding plane of the coal than along the bedding plane. Activation energies were 3.9 kcal mole-1 for helium and 13.6 kcal mole-1 for methane, with diffusion measured either along or across the bedding plane.

Jan 1, 1970

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 5 Typical Input - Ouput The input data and the printed output for case 8 of the simulations (Section A.4) are shown in the following. The branch, level, node, miner and hoist numbers mentioned in the input and output refer to the corresponding numbers in Figures A-3, A-4 and A -5, The plotted ouput, already shown in Figures A,11 and A-12 is not repeated. The input data shown does not include the following simulation parameters: DTIME = 0, 05 FTIME = 130 JPLT(K) = 1 for K = 1, 2, 3 0 for other K TPLSTR = 0.0 TPLST P = 130

Jan 1, 1976