Search Documents

By A. B. Hooker, L. C. IlsLey

 Previous publications relating to permissible methane detectors covered investigations of the detectors from January 1922 to January 1,1937. All of these detectors are obsolete, or the designs have been modified under extensions of the original approvals. This report covers the investigations of detectors since January 1, 1937, including the present permissibility requirements as to design and performance and a brief description of each detector.

Apr 1, 1942

By Arthur M. Hartstein

The Bureau of Mines, through contract with Ultrasystems, Inc., obtained data on the oxidative degradative behavior of a number of materials used in coal mines. Tests were performed using a stagnation burner arrangement. Materials examined included those used in typical coal mining operations such as (1) polyvinyl chloride-containing materials. (2) neoprene compositions, (3) rigid foams (urethanes/isocyanates), (4) miscellaneous materials (including jute, fiber glass, and polyethylene), (5) coal, (6) fluids (phosphate esters, organic esters, oil-water emulsions), and (7) composites. The composite comprised a mixture of a phosphate ester fluid with (1) coal, (2) a representative polyvinyl chloride sample, or (3) a neoprene-type composition. A number of decomposition products are identified that could represent a potential health hazard to miners including HC1, CO, SO2 and H2S, if they were generated to exceed toxic levels.

Jan 1, 1974

By T. J. Driscoll

In this Bureau of Mines investigation, the electrochemical polarization behavior of Fe and Fe-1BCr has been characterized in rigorously controlled 1[N] H2S04 solutions stirred with oxygen or an inert gas. Samples that under-went various levels of corrosion or passivation were examined using Auger electron spectroscopy (AES) and ion sputtering. Passivation of iron occurred at a potential of approximately 0.6 volt (1) in poorly stirred, oxygen-saturated solutions for forward polarization (scanning from cathodic to anodic potentials); (2) in pH-adjusted (increased), well-stirred, oxygen-saturated solutions for forward polarization; and (3) in well~ and poorly stirred, oxygen-and helium-saturated solutions for reverse polarization. Passivation of Fe-18Cr occurred at a potential of approximately -0.1 volt in helium-, nitrogen-, and oxygen-saturated solutions for all cases of forward polarization and most cases of reverse polarization. Elemental depth profiles obtained from AES sputtering measurements indicated that films or adsorbed species were present on iron samples in solution subjected to open-circuit, active, and transpassive corrosion, cathodic reduction, and passivation. This conclusion was reached by considering the distribution of the solution species, primarily sulfur, in the films, which were composed primarily of iron and oxygen. Sulfur was present throughout the films on actively corroding samples, in the outer regions of films of passive and transpassive samples, and on the film surfaces of open-circuit and cathodically reduced samples. For Fe-18Cr, sulfur was found on the surfaces of films on passive samples only, indicating that only the passive samples had films on their surfaces in solution. The films on electropolished and passive Fe-1BCr samples had the largest chromium concentrations, estimated to be approximately 45 at. pct, with less chromium in films of cathodically reduced, active, and open-circuit samples, in that order.

Jan 1, 1979

By Allen D. Look, Alan A. Sharp

"Churn drills for blast-hole drilling are important to the operation of most open-pit metal mines, but certain hazards are created through their use that cause fatal and nonfatal accidents.2/ The purpose of this circular is to present a code of safe practice prepared and followed at a large Arizona open-pit copper mine, where safety is recognized as a definite operating problem. Such a code, based upon a thorough study of available published information as well as practical experience gained from accidents and near accidents, is the result of considerable effort and monetary expenditure. It is hoped that other operations using churn drills may benefit by the code presented, either in comparison with existing rules or in the preparation of new operating instructions.The code presented is in use at the Morenci Branch of the Phelps Dodge Corn., Morenci, Ariz. Similar codes are used at the New Cornelia Branch, Ajo, Ariz., and in the waste-pit operation at the United Verde Branch, Jerome, Ariz.The authors gratefully acknowledge the cooperation of the Phelps Dodge Corp., whose personnel made: possible the collection of information included in this circular. Special acknowledgment is due Paul Simmons, safety engineer, and 3. U. Larsen, general drilling and blasting foreman, Morenci Branch, Morenci, Ariz.The importance of churn drills in Arizona mining is apparent when it is realized that at all the open-pit copper mines blast holes are drilled with this equipment. At Morenci, approximately 98 percent of the ground is broken by primary blasting of churn-drill holes.There has been a growing tendency in Arizona's copper-mining industry to change from underground to open-pit mining, with consequent increase in the use of churn-drill blast holes for primary blasting.3/Thirty-three churn drills are in use at Morenci for blast-hole drilling. The drills operate with 440-volt alternating current, and trailing drill cables, in 500-foot sections, connect with the portable drill transformer station.4/ Three Diesel-driven churn drills for drilling prospect holes also are in use. About 25 churn-drill shifts are operated currently on a three-shift basis. Ordinarily, a two-man crew is assigned to each drill; however, with prospect-drill crews a third man is added to handle the sampling.Benches are carried at a uniform height of 50 feet. Churn-drill holes are 9 or 12 inches in diameter and about 60 feet deep. The holes are 18 feet apart in hard waste and 21 feet in soft waste and ore, with toes from 11 to 13 yards at the shovel grade. Both the hole spacing and the toe have been increased gradually, until they are now 2 yards longer than in 1940. The average ground broken per hole is 3,500 tons, or 60 tons of ore per foot of hole drilled. The holes are drilled 10 feet below the bench to avoid leaving hard bottom, which requires secondary drilling and blasting.Starting with a 12-inch casing, the prospect holes average 1,200 to 1,500 feet in depth and terminate with 6-inch casing; the deepest hole drilled to date went to 1,735 feet.In addition, churn-drills are used at Morenci to drill blast holes in the silica pit, limestone quarry, and the tailings dam. Other irregular applications are the drilling of holes to set trolley roles and for concrete piling in building foundations."

Jan 1, 1950

By Marilyn Biviano

This analysis was conducted in response to concerns raised by the Chairman of the Energy and Commerce Committee of the House of Representatives regarding the potential impacts on automobile production, GNP and employment resulting from embargoing south African supplies of the platinum-group metals, platinum and rhodium. This analysis should be considered an addendum to the recently released study in which the direct economic costs I of a U.S. embargo on selected South African strategic and critical materials are estimated. The estimated GNP and employment impacts result when a mineral shortage reduces domestic industrial production and are in addition to the direct costs estimated in the earlier study. The direct cost to this nation resulting from a decision to embargo six south African strategic and critical minerals was estimated at $1.85 billion per year during the 1988-1992 time frame of the study. The estimated direct costs include the costs to U.S. consumers resulting from higher strategic mineral prices, lower mineral consumption, and the cost of developing higher cost domestic mineral resources. A large proportion of the costs result from the shortage of the two metals: platinum and rhodium. The average direct annual cost of embargoing is estimated at about $1.4 billion for platinum and $384 million for rhodium.2

Jan 1, 1988

By Raymond B. Ladoo

Cne of t·: . .:: i::,portt recent developrr.ents in the feldspar industcy l:.a.s beer. tl:.e r,:ipid. rise of Ne·N H.v-:psr.ire as a. feldspar producing State. Tl:.e unusual size and purity of t: e deposit now 'being worked ne3.r Keene, and tr.a i.nproved metl:.ods ot:' rr.ining srd ir,illing used l:.ave been responsible foe tt.is situation. ti'eldsp'.:l. w'ls occ':tsiona.lly produced sorr.e ye1rs ago in srr.a.ll (tuantities in New Hrunpshi :e, but t::.e State had not been considered a producer of" feldspar ui til lS3l. In the s::ring of tr .. at yea!', t:.e '[eane iic Products co. of Keene, N.H., beg3Il in a srr.9.ll way tl:e production of feldspar fro:n t1eir property in Gilsum, H.H., whicr. l-.a.d long been opera.tei a.s a :tl.ca mine. The purity of the feldspar at enoe '\ttracted f''.lvorai)le attention. and tt.e production of crude ore rapidly in­ cre'.\sed. Early in 1922, a new company, t'he Golding-Keene Co,

Sep 1, 1922

By Robert F. Chaiken

A novel approach to eliminating environmental and public safety hazards that are associated with fires in abandoned coal mines and waste banks involves the use of in situ combustion technology developed by the Federal Bureau of Mines to accelerate the burning of the wasted coals in place. This technology would be used under exhaust ventilation control conditions that would allow for total management of the hot gases produced. Combustion stoichiometries would be optimized to minimize unburnt combustibles and to maximize the heat content of the gas products, which will be exhausted at one or more fan locations. When necessary, scrubber systems would be employed to remove air pollutants, such as sulfur dioxide; heat utilization systems (process heat, steam, and electricity) would also be employed to offset operational costs. Ultimately, complete burnout would solve the fire and acid water formation problems of the abandoned coal mine or waste bank. Pertinent technical data for burnout control are derived and discussed in terms of the important material and operational parameters. In general, it is believed feasible to operate a burnout system in an existing abandoned mine or waste bank fire at thermal power levels in the range of 10 to 100 Mw, and at exhaust gas temperatures of 1,000° C (1,830° F).

Jan 1, 1980

By H. V. Makar

Ferrous fractions recovered from urban refuse were tested by the U.S. Bureau of Mines, U.S. Department of the Interior, to assess their character, composition, and response to detinning. This research was conducted as part of the Bureau's efforts to conserve mineral resources through recycling. Results from laboratory and pilot tests established the technical feasibility of detinning scrap recovered from household refuse. Detinned products containing less than 0.03 percent residual tin were produced. Concentrations of other residual elements were determined and compared with those in existing commercial scrap and with proposed specifications. Studies were extended to include evaluations under commercial conditions. Preliminary tests on 5-1/2 short tons of ferrous fractions revealed the need for adequate shredding to assure optimum metal-caustic contact and minimize retention of tin-bearing rinse solution in the final baled product. The washed metal product contained 0.06 percent residual tin. Subsequent melt tests showed a yield of 91.4 percent. Based on these studies, full-scale commercial demonstrations showed that detinned bales equivalent to No. 1 bundle quality could be produced in carload quantities. Up to 5 pounds of tin per gross ton of scrap is con-currently recovered during the detinning process.

Jan 1, 1979

By A. F. Colombo

In an effort to maintain an adequate supply of iron to meet national economic and strategic needs, the Bureau of Mines, U.S. Department of the Interior, is conducting research on methods for beneficiating the oxidized taconite resources located on the western Mesabi range in Minnesota, thus expanding domestic iron ore reserves. The selective flocculation and cationic flotation process was investigated in a pilot plant using an ore feed rate of 410 kg/hr (900 1b/hr) and 88 percent recycled water. Lime and a cationic flocculant were used to clarify the waste slurries treated in the water reclamation circuit. An oxidized taconite assaying approximately 36 percent Fe yielded concentrates averaging 63.5 percent Fe and 4.3 percent SiO2 and having an average iron recovery of 84.4 percent. The estimated reagent cost per tonne of concentrate was approximately $1.10. In an attempt to recover more of the iron lost in the flotation tailing, wet high-intensity magnetic (WHIM) separation was incorporated in the pilot plant circuit. The flotation concentrate grades obtained from beneficiation circuits with and without WHIM scavenging were similar, but when WHIM separation was used the overall iron recovery was increased by 2 to 9.5 percent, depending on the iron assay of the flotation tailing.

Jan 1, 1978

By Laurance L. Oden

The Bureau of Mines conducted corrosion tests of 18 commercial alloys in H3 P04 -phosphate rock or A1,03 slurry, in 10 pct HF, and in 25 pct H2 SiF6 to simulate three environments anticipated in a Bureau process to extract fluoride values from phosphate rock. Small alloy coupons were rotated in duplicate tests at 4.4 to 21 fps in the slurry at 170° C to determine rates of erosion-corrosion. At 4.4 fps the lowest rates, in mils penetration per year (mpy), were measured for Hastelloy C-276 (<20), Hastelloy B (30), and Inconel 625 (150);the rates increased at 21 fps to 55 mpy, 45 mpy, and 1,000 mpy, respectively. The corrosion rate for all alloys exceeded 40 mpy in either the equilibrium vapor or liquid phases of aqueous solutions containing 10 pct HF or 25 pct H2SiF6 at 100° C. Uniform corrosion in 10 pct HF at 50° C was observed only for Inconel 625 (22 mpy), Hastelloy C-276 (43 mpy), and Illium 98 (17 mpy). Inconel 625 (0.75 mpy), Hastelloy C-276 (1.3 mpy), Illium 98 (1.7 mpy), and Incoloy 825 (0.45 mpy) were attacked uniformly in 25 pct H2SiF6 at 50° C.

Jan 1, 1974

By Oliver W. Keener

The operation described herein differs from the usual practice in the Tri-State district in two important respects: (1) the ore is loaded into cars which are tramped to the shaft and hoisted on self-dumping cages, and (2) about 30 per cent of the ore is loaded by power shovels. The four-month period covered by the cost data appended at the end of the paper immediately followed a period of about one year during which the mine was shut down, and the expense incident to the resumption of operations is reflected in the costs. The author acknowledges the assistance of C. F. Jackson, mining engineer, U. S. Bureau of Mines, in the preparation of this paper and the compilation of the data.

Jan 1, 1929

By Richard J. Kline

This publication comprises tables listing friction loss for a flexible, spiral-reinforced circular ventilation tubing system. The tables were constructed with the following parameters: a friction factor of 62 X 10-10, 10-foot sections of tubing ranging in total length from 100 to 550 feet, air quantities ranging from 1,000 to 15,000 cfm, and one to four 90° bends in the tubing. The aim of this publication is to improve ventilation tubing analysis and to provide a method of proper fan selection.

Jan 1, 1971

By T. H. Jeffers

Significant amounts of cobalt, a strategic and critical metal, are present in readily accessible spent copper leach solutions. For example, recovery of cobalt at two major u.S. copper operations could produce about 1,300,000 lb Co annually, about 13 pct of domestic consumption. However, techniques such as solvent extraction and precipitation have not proven cost effective in separating and recovering the cobalt from these low-grade domestic sources. The Bureau of Mines has devised a procedure using a chelating ion-exchange resin to extract cobalt from a pH 3.0 copper leach solution containing 30 mg/L Co. Cyclic tests in 4-ft-high by 1-in-diam columns gave an average cobalt extraction of 95 pct when 65 bed volumes of solu-tion were processed at a flow rate of 4 gpm/ft2 of resin area. After an impurity scrub, eluates contained, in grams per liter, 0.4 Co, 0.2 Ni, <0.001 Cu, 1.3 Fe, 2.8 Zn, and 0.008 AI. Solvent extraction procedures to remove impurities, reject nickel, and concentrate cobalt produced a cobalt sulfate solution containing 80 g/L Co, 0.05 g/L Ni, and not more than 1 mg/L Cu, Fe, Zn, or AI. Based on data from commercial electro-winning operations, this solution appears suitable for production of metallic cobalt.

Jan 1, 1985

By C. P. Bowie

During the period of 10 years from January 1, 1908, to January 1, 1918, approximately 12,850,000 barrels of oil and 5,024,506,000 cubic feet of gas were destroyed by fire in the United States, entailing a total estimated property loss of $25,254,200. During this period 503 fires were reported. As is shown in Plates I and II, 310 of these fires were caused by lightning and 193 by all other causes. The losses from the fires caused by lightning were estimated to be $11, 148,000, and from those due to all other causes $14,106,200. Directly and indirectly, the fires resulted in the deaths of nearly 150 persons and were responsible for almost as many more being permanently disabled. For the past three years the Bureau of Mines has been conducting investigations to determine the nature and the specific causes of these fires, with a view to suggesting means whereby they may be suc- cessfully combatted and, in some places, perhaps eliminated entirely. As the subject of oil and gas fires is necessarily broad, no attempt is made in this bulletin to treat it exhaustively; rather the bulletin aims to point out what has been done by operators in the past, and to describe various fire-prevention methods and fire-fighting appa- ratus which are being used or adopted by many of the larger oil companies. These methods and apparatus, it is believed, if uni- versally employed by operators, will largely decrease the present enormous annual losses. In the discussion of oil-well fires, the methods used in extinguishing several of the larger and more perplexing ones are described. As the right procedure for extinguishing any oil-well fire must be de- termined largely by local conditions, it is not probable that all of the methods used at some one fire, as described, will be applicable to a future fire. However, the operator, from these descriptions, may at least gain suggestions that will greatly assist him in fighting similar fires.

Jan 1, 1919

By Isaac A. Zlochower

This paper presents data on the limiting (minimum) oxygen concentration (LOC), in the presence of added N2, of methane (CH4), propane (C3H8), ethylene (C2H4), carbon monoxide (CO), and hydrogen (H2), and some of their binary mixtures. It also addresses the issue of the flammable concentration (flammability) limits of these pure gases in air. The study is based on spark ignited explosions in large, spherical laboratory vessels (120-L and 20-L) using a 7% pressure-rise criterion for explosion propagation. The results of the study are compared with the older values which used long flammability tubes with a diameter >5 cm together with visual evidence of substantial upward propagation. They are also compared to results reported recently using a 12-L spherical flask with a visual flame propagation criterion. Finally, they are compared to results reported in Europe using more modest flammability criteria and smaller chambers. The findings reported here show excellent agreement between the 120-L and 12-L results, good agreement with the 20-L results, and reasonable agreement with the earlier flammability tube values for the lower flammability limits. They disagree, however, with the more conservative European values. These results and those from the 12-L experiments also feature lower LOCs than are given by traditional flammability tubes. A model for the LOCs of such fuel mixtures based on the Le Chatelier mixture rule for lower flammable limits is seen to reasonably fit the observed results on binary mixtures and can accommodate more complex mixtures as well. One such set of ternary mixtures containing CH4 and 1:1 CO:H2 is well fitted by the model.

Jan 1, 2009

By J. P. Morris

This paper describes a gas-transport method for measuring vapor pressures of liquid metals. Vapor pressures of iron and nickel were determined at temperatures between 1,540° and 1,620° C. The results can be represented by the following equations: log Pmm (iron) -19,460/T + 9.147, log Pmm (nickel) -2l,030/T + 9.689. The study was undertaken as part of a program to determine thermodynamic activities in liquid iron alloys.

Jan 1, 1957

By L. B. Pankratz

The heat content above 298.15° K was determined for crystalline vanadium silicide of the composition V3Si. This substance has a minor thermal anomaly (probably a heat-capacity maximum) near 560° K; the extra heat absorption is about 50 cal/mole. The original heat-content data are presented, and smooth values of the heat content and the corresponding entropy increments are listed for the temperature range from 298.15° to 1,500° K. Equations representing the heat- content values and derived heat capacities are also included.

Jan 1, 1963

By F. W. Hoertel

The Bureau of Mines investigated the use of depleted uranium as a sacrificial anode for the cathodic protection of submerged and underground structures of iron , steel , and copper . Uranium-metal couples were tested in simulated marine environments of varying oxygen contents at pH values between 5.5 and 8.5 and under simulated boiler service condition in Rolla , Mo. , city water . Similar couples were tested in samples of Missouri soils to simulate underground service . Uranium remained anodic to iron , steel , and copper in the simulated marine environments and under simulated boiler service if the electrolyte was oxygen- free city water . Uranium appeared to offer limited protection to iron , low- carbon steel , stainless steel , copper , and zinc in the simulated underground tests . Uranium anodes offer a space advantage because 1 cubic inch of uranium gives approximately the same protection as 2 cubic inches of magnesium or 1-1 /2 cubic inches of zinc .

Jan 1, 1963

By T. E. Gray

This report describes the preparation characteristics of the more significant coal beds in Allegheny County, Pa. It is one of a series planned to determine coals suitable for producing metallurgical coke, either as mined or after beneficiation. More than 7 million tons of coal was produced in Allegheny County in 1957. Of this, more than 5 million tons was cleaned mechanically in nine cleaning plants. The Bureau of Mines estimated that, as of January 1, 1953, more than 384 million tons of recoverable coal remained in the county in beds 28 inches or thicker.

Jan 1, 1959

By T. E. Gray

This report describes the preparation characteristics of the more significant coal beds in Washington County, Pa. It is one of a series planned to determine coals suitable for producing metallurgical coke, either as mined or after beneficiation. More than 15 million tons of coal was produced in Washington County in 1956; 89.8 percent was cleaned mechanically in 10 cleaning plants. The Bureau of Mines has estimated that 2,280 million tons of recoverable coal remained in beds 28 inches thick or more as of January 1, 1954.

Jan 1, 1959