Search Documents

By S. P. Kinney, A. C. Fieldner, S. H. Katz

"1 Introduction The regrettable death of James S. Cunningham, Foreman Miner, attached to Bureau of Mines Rescue Car No. 2, while wearing a half-hour type oxygen breathing apparatus in a gasoline storage tank at Trinidad, Colorado, raised the question as to the possibility of gasoline vapors permeating the rubberized fabric of the breathing bags of such apparatus.It is known that most gases and especially certain organic vapors permeate rubber, by solution or a similar process. The rubber becomes saturated with the gas and if a concentration of gas is maintained on one side of the rubber sheet it slowly gives off gas from the other side. It of course takes some time for the gas to diffuse through the rubber and the length of time before it reaches the other side is proportional to the thickness of the rubber. The amount of gas that passes through per unit of area in unit time increases with the concentration of gas and also varies with the structure and composition of the rubber.It has been suggested that the gasoline vapor could not have penetrated into the interior of an oxygen breathing bag because the pressure is greater on the inside, but this is not true as the process of permeation by solution in the rubber is affected only by the difference in the partial pressures of gasoline vapor on the inside and outside of the bag. The positive oxygen pressure on the inside can only prevent the entrance of gasoline vapor through measurable holes, and has no effect on permeation by diffusion through the rubber."

Dec 1, 1919

By John C. Edwards

Several experimental programs were conducted at the Pittsburgh Research Center to investigate the level of mine fire detection and alarm capability possible using state-of-the-art technology. These programs involved comparison of the response and alarm time of optical and ionization type smoke sensors to smoldering and flaming coal combustion in a smoke chamber. Coal combustion experiments conducted in the smoke chamber demonstrated that a CO concentration of 5 ppm above ambient corresponded to an optical density of 0.022m1. For the four smoke sensors for which a continuous analog signal was available, a smoke sensor alarm was defined as the average background signal plus ten times the peak-to-peak noise. This alarm criterion resulted in the association of the alarm for three of the four sensors with a smoke optical density of 0.022m-1. and 0.033m-1 for the fourth smoke sensor. The smoke sensors used in the smoke chamber studies were incorporated into large scale diesel fuel fire experiments conducted under normal ventilation conditions in the Safety Research Coal Mine (SRCM) at the Pittsburgh Research Center. These experiments showed that a diffusion mode smoke sensor alarmed earlier than a diffusion mode CO sensor; and, based upon the measurement of the optical transmission at the location of a pump mode ionization type smoke sensor that a pump mode ionization smoke sensor alarmed at an average smoke optical density of 0.021m" for the twelve experiments conducted. A series of 30 and 330 kW diesel fuel fire intensity experiments were conducted under zero airflow conditions in the SRCM. It was determined that :(I) thermal sensors are inadequate at 30 m from a 300 kW fire;(2) a diffusion mode ionization smoke sensor can be more effective for mine fire detection than a diffusion mode CO sensor;(3) recommendations can be made for sensor spacing in a mine entry based upon the measured CO buoyancy induced spread rates along the mine roof and the time for a developing coal fire to ignite a conveyor belt.

By Bernard Lewis, Guenther von Elbe

"Explosive gas mixtures are characterized by their ability to undergo a self-accelerating reaction that may culminate in ignition. In the case of methane and air there are two interdependent causes of this acceleration. First, if a sufficiently fast reaction is induced, heat may be evolved faster than it is lost to the surroundings; consequently, the temperature rises and the reaction rate increases. Second, the reaction rate is determined not only by temperature but by the concentration of reactive intermediate products if the latter increases during the course of the reaction the rate will increase. To understand the role of these active intermediates, it should be realized that molecules of methane and oxygen, per se, show little tendency to react with each other even at high temperatures.(1) If, however, free radicals like OH and CH3, are present in the mixture, the methane and oxygen are attacked in the reactions(2):In these reactions the radicals are regenerated, and thus a chain of reactions is set up by an individual radical or chain carrier which is broken only if the latter is destroyed in some process. Not all collisions of a chain carrier with CH4 or 02 result in reaction, since one requirement for a successful collision is that the colliding particles have a certain minimum energy. The percentage of collisions in which this energy condition is fulfilled increases with temperature, so that for equal chain-breaking probabilities the length of the reaction chain increases with increasing temperature. Thus, there exists an interplay of temperature and concentration of chain carriers that determines the reaction rate. To carry the rate to the stage of self-acceleration, higher temperatures are required for lower than for higher chain-carrier concentrations, other conditions being equal."

Sep 1, 1939

By D. Litton, H. Dobroski, J. G. Kovac

Since 1910, the U.S. Bureau of Mines (USBM) has investigated practical ways of dealing with the consequences of major fires and explosions in underground mines. The results of this research have had a significant positive impact on the mining community by enhancing mine workers’ chances of surviving an underground mine disaster. Today, the Bureau continues to conduct research in mine disaster mitigation. Much of this work has direct application to search and rescue situations, such as: emergency evacuation through smoke-filled or otherwise unbreathable atmospheres, locating and rescuing survivors from rubble piles, and fire fighting in confined spaces. Three USBM research areas are discussed: (1) Life Support -- This effort is directed toward research into and development of closed-circuit breathing apparatus for use in hazardous environments which are likely to be encountered in the aftermath of a mine disaster. (2) Trapped Miner Location -- A mine disaster may result in the entrapment of miners whose normal escape routes are cut-off. This research activity resulted in the development of transportable seismic technology that can be used to locate trapped miners. (3) Mine Fire Diagnostics -- This research involves developing practical techniques for remotely monitoring how the atmosphere inside a mine changes during a fire, in order to estimate the spread and severity of an underground fire. This information is critical in deciding how best to fight a mine fire, or whether it is safe to mount a rescue and recovery mission.

By L. D. Tracy

"Introduction In the course of the investigations by the Bureau of Mines into the various causes of coal-mine explosions, the fact that several gas explosions had occurred during or very soon after a mine was being un-watered, attracted the attention of the Bureau's engineers. The apparent coincidence was so marked that there appears to be an extra hazard present, whenever water, which has been standing against the face of the coal for some time, is suddenly removed either by natural drainage or by mechanical means.Actual Occurrences Case 1. - A typical illustration of this hazard is shown in a gas explosion which occurred in a mine in Central Pennsylvania. Four main entries, 50 feet apart with an average grade of 6 per cent, had been driven with the dip of the coal, and from these mains 7 pairs of entries, at intervals of 800 feet, had been turned at such an angle that their grade was slightly rising. Prom these latter pairs of entries, rooms were turned practically at right angles.The main entries had been driven for 4,500 feet and at the face there was 400 feet of cover. As far as could be observed, the roof was of sandstone and the floor of clay.The coal bed being mined was the Lower Kittanning, which has a thickness of about 4 feet. A typical analysis of the coal in that section is as follows:"

Oct 1, 1924

By N. A. Caspero, W. E. Eckard, W. T. Wertman

A thermal oil-recovery experiment was conducted in the Venango First sand, Goodwill Hill oilfield, Warren County, Pa., about 10 miles northeast of Titusville. The Quaker State Oil Refining Corp., Bradford, Pa., performed the experiment with assistance from Sinclair Research, Inc., Tulsa, Okla., and the Federal Bureau of Mines. The Goodwill Hill field was discovered in 1885. Primary-production oper- ations continued until 1930 when an air-gas injection project, which is still in operation, was started. At the location of the combustion experiment, the reservoir is 400 feet deep and 30 feet thick, with wide permeability and porosity variations. The crude oil is typical Pennsylvania Grade paraffin- base oil with a gravity of 43.9° API and a viscosity of 4.55 cp at 60° F. The well pattern for the experiment consisted of 5 producing wells, enclosing an area of 1.28 acres, and a central ignition-injection well. An air-natural gas mixture was ignited in the ignition well on July 29, 1961. Ignition was followed by injection of air and natural gas at various rates. The experiment was suspended January 5, 1962, when it became evident that economic oil production could not be achieved. There was no conclusive evidence that self-sustained combustion was achieved or that combustion increased oil and water production. A slight increase in liquid production was attributed to stripping action caused by the air-injection rates, which were higher than those normally used during air-gas injection.

Dec 1, 1963

By M. Gottlieb, P. Metes, Charles Sabine, Louis J. Denes, B. Kaminsky, Jami M. Girard, Ronald T. Mayerle

A significant risk factor in assessing and modeling potential catastrophic slope movement in open-pit mines is the presence of argillic alteration in host rocks. High-resolution hyperspectral imagery operating in the visible to shortwave infrared can be a useful tool for identifying and mapping potentially dangerous argillic zones. We have conducted preliminary experiments with a new type of hyperspectral imager that employs an acousto-optic tunable filter, a variable retardation plate and a standard digital camera. The instrument we tested operates in the .5-1.0 micrometer range. A shortwave infrared instrument is planned, and mid-infrared instruments have been designed. An AOTF consists of an acoustic transducer that generates an acoustic wave that propagates through an attached crystalline substance. The wave sinusoidally modulates the refractive index of the crystal, selectively diffracting incident light according to its wavelength. The instrument also measures polarization signatures of reflecting surfaces as well as their spectral properties, opening up new areas of possible research. Images can be acquired and processed at 30 frames/second. The AOTF camera system offers numerous advantages to geologists. It can be used as an airborne imager or as a portable field device to image pit walls, outcrops, rock specimens or drill core. It can be adapted to image polished sections under a microscope, and it could be used in underground workings. Algorithms can produce processed images in real time (e.g., ratio images), and, because it is a camera system, aerial images can be orthorectified.

By R. F. Abernethy

A small-scale method was developed for determining the free-swelling index of coal samples of limited quantity, especially the macerals. Results of a series of tests using a 0.3-gram sample correlated well with those by the standard method using a 1-gram sample. The standard and small-scale methods are modified to give unrestricted swelling for those coals having swelling index numbers above 7.

Jan 1, 1971

By J. H. Perkins

The Bureau of Mines has conducted desorption work on fine coal particles at near atmospheric pressure. An apparatus Iris been developed that uses a capacitance manometer to measure desorption of methane from coal particles up to, 2 inches in diameter and pressures up to 1,000 psi. This will make it possible to duplicate the desorption process as it occurs in its natural underground environment.

Jan 1, 1969

By K. Rubow, Z. Zhlqun, V. Marple

A theoretical technique has been developed and verified experimentally for determining the aerodynamic diameter of irregular shaped particles. The aerodynamic diameter of a particle is a very important property in determining where that particle deposits in the respiratory tract. Many instruments, such as impactors and cyclones, will determine the aerodynamic size distributions of aerosol particles but few analyze the particles individually. The theoretical approach of our technique is to solve, by use of high speed computers, the three dimensional Navier-Stokes equations to obtain the flow field around an irregular shaped particle of any contour. The computer program will then determine the drag on the particle, and thus the aerodynamic diameter of the particle can be calculated. The experimental approach has been to pass the particles through a centrifuge and collect the particles upon a collection foil. The position of a particle on the foil is an indication of its aerodynamic diameter. These particles were then shadowed in two orthogonal directions and inspected under an SEM. The top view of the particle in the SEM plus the views of the two orthogonal shadows allows one to determine the three dimensional shape of the particle. Studies have been performed on silica, coal and talc particles with aerodynamic diameters in the 1 to 4 um size range. The three dimensional shape, as is determined from SEM analysis was used in the theoretical computer program and the results compared. It was found that in most 'cases the agreement between the experimentally and theoretically determined aerodynamic diameters was within 5%.

Jan 1, 1988

By C. B. Manula, R. L. Sanford, R. A. Rivell

A central requirement for using simulation models is the need for retrospect testing to validate experimental conclusions. Acceptance of a model by managers and safety practitioners is more likely to depend on its tested performance in-the field rather than on the underlying logic or the validity aspects of the model itself. It is here that simulation bridges the gap between theory and useful design procedures. The original version of the rail haulage sub-assembly was success¬fully tested in the field (Sanford, 1969). However, the case studies that were described here involved single-stage haulage and restricted jobtypes from UGMHS. Since this report together with Volume VI (Production Subsystem) describes extensive changes and modifications to the rail haulage sub-assembly and UGMHS, field tests were necessary to verify both the rail model and the linking concepts to the Produc¬tion Sub-system. Mine Description The candidate mine selected for model verification works the 6 1/2 foot Pittsburgh seam. Shaft openings are used for manways and ventilation and a dual compartment slope for materials handling. In the bottom half of the slope, a hoist with track handles supplies and equipment. In the upper half, a 42 inch belt conveyor travelling at 450 fpm moves coal from a rotary dump to the surface. The immediate roof is shale with the first 12 inches taken during development mining. About 4500 raw tons are produced daily from seven face units and one spare working three shifts. At seven of the sections,

Jan 1, 1974

By Richard V. Ageton

"Everyone admits that there are more accidents in metal mines than there should be but there is much difference of opinion as to the causes of accidents, whether avoidable or unavoidable, and the amount of responsibility attaching to the miner and the mine operator, respectively. However, it seems that one of the main reasons why there are so many accidents, is that there is so little general knowledge regarding their causes and costs. Some information regarding the costs and causes of metal-mine accidents is presented in this paper.The data contained were obtained from a study of the complete accident and medical reports of two large metal-mining companies, which carry their own insurance. Path maintain hospitals with competent medical attendants. One of these companies also maintains a very efficient safety bureau, consisting of a safety engineer, with two assistants who work in connection with the medical department, and with the safety committee made up from among the miners themselves.Daring the year of 1920, ""A"" Company employed approximately 900 men, and these men worked more than 270,000 shifts. There were 373 minor and major injuries, among these 900 men, hence assuming that each injured man was hurt cut once, 41 per cent of the men who worked in this mine received some kind of time-losing injury during the year. On account of these injuries the injured men lost 3731 shifts, and thus the time lost due to injuries amounted to approximately 1.4 per cent of the total number of shifts worked,"

Oct 1, 1923

By Joseph Cervik, J. H. Perkins

The Bureau of Mines has conducted desorption work on fine coal particles at near atmospheric pressure. An apparatus has been developed that uses a capacitance manometer to measure desorption of methane from coal particles up to 2 inches in diameter and pressures up to 1,000 psi. This will make it possible to duplicate the desorption process as it occurs in its natural under- ground environment.

Aug 1, 1970

By Roy H. Grau, John C. LaScola

This Bureau of Mines report contains a tabulation of methane emissions during 1980 for all coal mines located in the United States with emissions greater than 0.1 MMcfd. Listed for each mine are methane emission quantity, location, and coalbed. The report also compares records of 1975 and 1980 and describes relationships between emissions in 1980 and the Bureau's coalbed gas content data on 11 mines.

Jan 1, 1984

By Alan R. Buehler

A mineral survey of the 20,792-acre Sand Butte WSA (Wilderness study Area), ID-57-8, was conducted by U.S. Bureau of Mines personnel in 1985, at the request of the Bureau of Land Management. The WSA is in Lincoln County, south-central Idaho, about 15 miles south-southeast of Carey. There are no mines, prospects, or claims within the WSA. Basaltic lava is the only rock type exposed within the WSA. The only mineral resource is a few tons of a platy variety of lava (slab pahoehoe) which is suitable for use as decorative stone. Similar slab pahoehoe, produced from other lava fields in southern Idaho, retails for approximately $125/ton. The deposit in the WSA is too small to be mined commercially but may have value to consumers who gather their own decorative stone. INTRODUCTION A mineral survey of the Sand Butte WSA (Wilderness Study Area) 1/ was conducted in June 1985 by the USBM (U.S. Bureau of Mines) and the USGS (U.S. Geological Survey) at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will he used to help determine the suitability of the WSA for inclusion into the National Wilderness Preservation System. The immediate goal of this and other USBM mineral surveys is to provide data to the President, Congress, government agencies, and the public for land-use decisions. The long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By Bruce K. Cantrell, Winthrop F. Watts

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989(1), which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This report reviews, available diesel exhaust aerosol and gas measurement techniques. Measurement of human exposure to toxic agents is the first step in determining the exposure-dose-response relationship. It is a fundamental step in risk assessment. Measuring exposure to diesel exhaust pollutants is particularly challenging due to the complexity and variability of exhaust components. This paper reviews current occupational health standards for diesel emissions and available diesel exhaust gas and aerosol measurement techniques. Although surveys in mines have primarily assessed diesel exhaust exposure using diesel particulate matter (DPM) some exhaust gas measurements have been used as indicators of exposure. DPM is emphasized because it is a major component of diesel exhaust, is suspected to make a major contribution to the health hazard, and is measurable. OCCUPATIONAL HEALTH STANDARDS Occupational exposure surveys of diesel exhaust frequently measure regulated pollutants, or pollutants that are suspected carcinogens, even if no permissible exposure limits (PELs) have been established. In the United States, various organizations recommend a range of allowable values for diesel exhaust gaseous constituents, including carbon monoxide (CO), carbon dioxide (CO2), sulfur dioxide (SO.), nitrogen dioxide (NO2), nitric oxide (NO), and formaldehyde (HCHO). Table I summarizes these recommended levels, showing 8-hour or 10-hour time-weighted-average values where available; where these are not available, 15-minute short-term [ ]

Acid pollution from abandoned mines causes serious contamination of major streams in coal mining areas. In Pennsylvania alone it is estimated that 3000 miles of streams are devoid of fish and plant life because of coal mine effluent.1 The pollution arises because water and oxygen react with iron sulfide in the mine cavity to produce sulfuric acid and iron sulfate, which later find their way back into surface streams. Two general approaches to the problem are possible: (1) prevent the acid-forming reaction from taking place, (2) treat the acid mine water after it is formed so that it will not be harmful to the ecology when discharged into streams and other surface waters. The work described in this report belongs in the first category - it was based on the assumption that acid formation in the mine cavity can be prevented by keeping water (one of the reactants) out of the mine. This was to be accomplished by-forming a waterproof seal over the mine cavity which would prevent the seepage of surface water into the mine. It was planned to form such a seal at or near the surface of the ground by applying latex to the soil. Ideally a dilute latex would be applied to the soil and would penetrate to a depth of two to three feet below the surface where it would be coagulated by reacting with a constituent of the soil or by other means., A seal below the surface of the soil would have several advantages over a surface seal - it would not be subject to destruction by traffic, frost or vegetation and, more important, it would allow the use of the top soil for many agricultural purposes. A preliminary feasibility experiment was performed prior to application for the present grant. It showed that it was indeed possible to form a sub-surface seal by means of latex. A core of soil was obtained locally (Wayne, N. J.) by driving a 6.5 cm inside diameter steel pipe about 100 cm long into subsoil for a distance of 71 cm. The soil was retained within the pipe for this experiment. A part of the free space above the soil in the pipe was charged with water, and the seepage rate of the soil after it had become saturated was 15 ml/min under a total head (wet soil plus supernatant column of water) of 92 cm. After the supernatant water had drained completely, 100 ml of 5% rubber latex was added and allowed to seep into the soil. This was followed by additional water and the seepage rate was found to be 2 ml/min under the same head. This seepage rate remained unchanged when remeasured on the following day. Since there was no visible evidence of the latex in the collected drain water it is presumed to have been retained by the soil.

Jan 1, 1972

By A. W. Khair, S. J. Jung

"A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.1. INTRODUCTIONMuch research in the past has been done on energy requirements and mechanism of energy dissipation for ideal rock fragmentation in cutting process. However the mechanisms of energy dissipation or failure criteria for rocks in cutting process in order to evaluate the efficiency of energy requirements in specific rock fragmentation is not well understood. The formation of a crater in rock under the impact blow of a bit has been observed experimentally (Hartman, 1959). It is known that directly beneath the edge of the bit the rock is crushed into fine powder, toward the sides of the crater it chips out into relatively large fragments. (Sikarskie & Cheatham, 1973). Singh et al. (1967) investigated the cratering process under the two different conditions of static and dynamic loading. They found that the amount of energy consumed per unit volume of crater is unequal for the two different loading conditions. A complex network of fractures often extends downward and laterally into the rock below the bit. The surface of the specimens showed that the dynamic loading damaged larger area then the static loading."

Jan 1, 1989

By D. Harrington, C. W. Owings

"The belief is now fairly general among the coal-mining people of the United States that one of the most effective methods of preventing wide-spread coalmine .explosions is that of introducing rock-dust into coal mines to reduce the inflammability or explosibility of dusts found on mine surfaces. Notwithstanding this belief it is improbable that even a small fraction of 1 per cent of the coal mines of the United States are at all adequately protected by rock-dust; in a survey made in the summer, and fall of 1927 it was found that but 463 out of more than 7,000 operating bituminous and lignitic coal mines were using rock-dust at all, and that few if any of the 463 were fully or adequately protected by rock-dusting.Inspections of a large number of mines through the United States by Bureau of Mines safety division field men have failed to reveal a single adequately rock-dusted mine, Yet there is no doubt that many of the owners and operators believed their properties to be fully protected by rock-dust against the much-feared hazard of widespread explosion. Two of the most disastrous explosions of recent years occurred at properties where the owners were definitely of the belief that the rock-dusting done had made the mines immune to widespread explosion involving coal-dust. In both instances it was found that although some rock-dusting had been done, the mines were more nearly 1 per cent than 100 per cent rock-dusted.This condition as to inefficiency or insufficiency of rock-dusting in the coal mines of the United States is almost universal, and unless our mining men awaken to its, dangers, the disaster record of the coal-mining industry is much more likely to become worse than better. During the fiscal year ended June 30, 1928, the attention of the safety division of the United States Bureau of Mines was called to. 22 explosions With 320 fatalities in bituminous coal mines of the United States; and of the 22 explosions there were 10 with 258 fatalities in mines that were listed as having used rock-dust; upon investigation it was found that as usual the rock-dusting had been anything but comprehensive or adequate. It is probable that in a very few instances last year the relatively small amount of rock-dusting stopped the .extension of the explosion and thus prevented further expansion of the death list. In general, however, the explosions occurred in a part of the mine that had not been rock-dusted - and right here is the crux of the failure or probable failure of present-day rock-dusting in the United States, There should be no part of any bituminous or coal mine in which all of the exposed surfaces (roof, ribs, and floor) have not been thoroughly rock-dusted and kept thoroughly rock-dusted. In other words, all exposed surfaces of all accessible places in bituminous and lignitic coal mines should be kept covered with rock-dust so that the combined rock-dust coal-dust mixture at all times and in all places has less than 35 or 40 per cent combustible matter, The only exception to this rule is that surfaces which are wet (and this does not mean merely damp) need not be rock-dusted. However, a mine opening may have several inches of water on the floor and yet have much explosive dust on the ribs and roof above the water; in such places the ribs and roof should be kept rock-dusted, irrespective of the wetness of the floor."

Nov 1, 1928

By W. W. Weller

Low-temperature heat capacity measurements were conducted, and entropies at 298.15° K were evaluated for sodium monomolybdate (Na2Mo04), magnesium monomolybdate (MgMo04), and calcium monomolybdate (CaMo04). The 298.15° K entropy values were sodium monomolybdate, 38.1±0.3 cal/deg mole, magnesium monomolybdate, 28.4±0.2 cal/deg mole, and calcium monomolybdate, 29.3±0.2 cal/deg mole.

Jan 1, 1963