Search Documents

By D. Harrington

"The fire boss in coal mining and the shift boss in metal mining, though held responsible to a large extent for safety of underground employees and of the mine, are, it seems to me, not always vested with sufficient authority nor given compensation commensurate with their duties. The metal-mine shift boss, although his position as regards his relations between employer and employee, is frequently an unenviable one, has as a rule much more authority than the fire boss and is not expected to perform the menial tasks required of the latter by many coal-mining companies.In most coal-mining States the coal-mine foreman and the fire boss are re¬quired to possess a certificate of competency obtained by passing an examination. The foreman is legally responsible for the safety of the miners, as in most instances the superintendent is not required to pass an examination. Although the foreman is held legally responsible for the safety of the miners, the law does not, in general, compel the superintendent or other higher officials to delegate sufficient authority to the foreman to enable him to put his wishes or judgment into effect; and this condition has tended in many instances towards perpetuation of unsafe conditions.The fire boss is held legally responsible for conditions in his ""beat"", but he is generally given only such authority as the mine foreman sees fit to delegate, frequently very little, Moreover, the fire boss is generally required to cover his ""beat"" within two hours before the entrance of the underground workers. Only too often his territory is so great that in order to reach all the working faces and chalk the required date at the face, he must travel at a rapid walk or even run. When such haste is necessary to cover the required ground, it is manifestly im¬possible for the fire boss to make a careful inspection or examination of the roof, timbering, wiring, gas, etc., at each place, and doubtless in his hurry many unsafe conditions escape his notice."

Sep 1, 1920

To develop a reliable, remotely-controlled, mobile roof support to eliminate the need to set posts, cribs, or props while extracting coal pillars. Approach The primary danger during pillar extraction is premature caving of the mine roof. The roof must cave predictably and dependably to ensure the safety of miners. Support during retreat mining is usually obtained by setting posts, cribs, props, roof bolts, or a combination of these devices. These are set manually by miners in the working area. To help minimize the danger to mine workers and to equipment posed by premature falls, the Bureau of Mines developed the mobile roof support (MRS) system to secure the roof during pillar extraction. How It Works The Mobile Roof Support (MRS) is eight-feet-wide, ten-feet-long and five-feet-high, with twelve inches of ground clearance. It is ruggedly built and exerts less than 20 psi ground pressure. The MRS is powered by a 40-hp, 460-v AC permissible motor. The reversible, variable tram speed is 80 ft/min on a 20-percent grade. It is tire-mounted, has a trailing cable, and is remotely controlled either by a radio or a tether communication cable. The machine carries four 50-ton jacks which serve as props for working heights from seven to fifteen feet. Two jacks are chassis-mounted and two are on swing arms. Each jack has a cap which distributes the roof load to three paints. The swing jacks form a breaker row to stop falling roof and prevent caving Into the work area. One jack has a visual load indicator and a second is wired to the machine lighting system. Blinking lights indicate when the preset loading is being exceeded. In the case of excessive loads, an ability to remotely jettison either or both swing jacks has been incorporated into the system to permit removal of the MRS while the roof is still supported.

Jan 1, 1985

By M. J. Ankeny

The expression "firing open, unconfined shots," as used in this circular, means the firing of explosive charges not confined in boreholes. Examples are the so-called mudcap shots, adobe or dobe shots, or bulldozing shots consisting of explosive charges placed on, under, or between rocks for the purpose of breaking them. The practice of firing open, unconfined shots is not uncommon in coal mines, despite the fact that numerous mine explosions and dust ignitions have resulted from this practice. The usual method of preparing such shots is to place the explosive with its detonator on top of a piece of rock or coal and cover it with clay, loam, sand, or road dust; frequently no covering of any kind is used. In some mines, an open charge of explosive is placed on timbers to dislodge them or in crevices in the roof to break down loose rock that cannot be dislodged with a bar or pick. The explosive charges may be made and fired singly, although sometimes several charges are placed on one large piece of rock with a detonator in each charge, and all charges are fired simultaneously. Although it is general practice to use permissible shot-firing devices, which will not ignite gas or dust to fire these charges, electric power from the regular mine circuits is sometimes used. When the shot is fired, any coal dust that may be present is thrown into suspension by the blast and may be ignited by the intense hot flame of the explosive or by an arc or spark at the leg wires or the end of the firing leads if power from the regular mine circuit is used to fire the shot. Even if there is not enough coal dust present to form a dust cloud, open, unconfined shots can readily ignite methane.

Jan 1, 1952

"""Hazard"" is the general expression used by safety engineers to denote risk, or the danger to property or human beings from the contingencies peculiar to different industries. Where a business, family, or individual is subjected to possible financial loss from any particular hazard, it is customary and is considered good practice to insure for reimbursement of possible loss. Accordingly, we take out insurance for earthquakes, for fire, for accidents, etc., and are charged a different premium for each. The premium rate is based on our relative exposure to the hazard in comparison to the total loss to our particular class of business in our geographical location over a given period.Insurance, then, must be considered as the experience of a group rather than of an individual, and any individual may be fortunate or unfortunate over stated periods. Through the law of averages, the probability of loss because of exposure to hazard is becoming more accurately measured as experience is accumulated and data are analyzed.Lion human life came to have a financial value in the eyes of the law, and employers were held liable for losses through accidents to employees while on duty, insurance companies began to underwrite the accident risks of the different employers and divided them into classes based on the amount of risk involved. Premiums for compensation insurance are based on relative exposure, which is measured by pay roll. The premium is rated in proportion to the severity of losses established by statistical studies.' It soon became evident that the accident experience of employers in the some industry varied widely; that is, there were good and bad risked in the same line of business. This resulted in ""experience rating"" of premiums, meaning thereby that an employer with experience in accident cost was premium rated in proportion to his losses over a stated period (usually three or more years)."

Feb 1, 1926

Three -dimensional boundary value problems are difficult to solve. Indeed, while the separation of the scalar wave equation can be effected in 11 different coordinate systems, an analytic solution requires that the boundaries, both external and internal, possess the same symmetry as the coordinate system. Numerical methods are thus of great importance for the solution of such problems; however, despite the availability of high-speed, large memory digital computers , the solution to a significant three -dimensional problem is by no means trivial. It is unfortunate that the results reported here by Jones are invalid. Jones discusses a model in which a three-dimensional island lies off a linear coastline where all the interfaces lie in the coordinate planes in a Cartesian system. A downward plane em wave polarized with the electric field parallel to the linear coastline, and two of the islands coast, is incident downward. This, of course, requires that the incident electric field is perpendicular to the other faces of the idealized Cartesian island. The significant equation used by Jones for his finite difference calculations is [ ] where n2 = sµ? . is the conductivity, µ=µo is the permeability of the appropriate medium, and w is the angular frequency of a Fourier component of the incident field. We see that the displacement current term is omitted, which is an excellent approximation for the parameters of interest in this model. In the similar equation for the y- component of the diffusion equation, the same considerations which we are about to discuss are equally valid. It can be seen from the equation that the field components are related and thus any errors introduced will be propagated into all three components. The difficulty arises when Ex or E is perpendicular Y to one or other of the surfaces of discontinuity in s. The continuity of current at the air-earth interface (upper surface), e. g., jy, requires

Jan 1, 1973

By John Redington

This paper describing the milling practice at the Coniaurum Mine is one of a series of papers on milling methods, practice, and costs prepared in cooperation with an published by the United States Bureau of Mines. The 500-ton will of the Coniaurum Mines (Ltd.) is located at approximately the center of the company's property and a little more than a mile from the town of Schumacher, Ontario. The main shaft through which all the ore is heisted is adjacent to the mill so that the ore hoisted in a 3-ton skip is dumped directly into a 15-ton bin at the crusher.

Jan 1, 1931

By LB. Berger

"INTRODUCTION The use of gasoline engines as the motive power for lift trucks, tractors, and other types of mobile equipment operated in enclosed spaces, such as industrial plants and warehouses, may create a hazard because of the carbon monoxide present in the exhaust gases of the engines; gasoline-powered equipment should not be used in mines or tunnels. Because the equipment is mobile, local ventilation usually is impracticable, and general ventilation of the spaces is nec-essary to dilute and remove the carbon monoxide. To estimate the rate of ventilation required in such situations, information is necessary on the concentration of carbon monoxide in the exhaust gas and the rate at which exhaust gas is produced under given operating conditions. The purpose of this paper is to present data that may be used in making estimates of ventilation requirements.COMPOSITION OF GASOLINE-ENGINE EXHAUST GASThe exhaust gas of a gasoline engine consists mainly of carbon dioxide, carbon monoxide, hydrogen, oxygen, and unburned hydrocarbons (usually reported as methane), together with the nitrogen present as a residue from the air sup-plied for combustion. 3/ The exhaust also contains water vapor resulting from combustion of the hydrogen of the fuel. The water-vapor content is not included in exhaust-gas analyses calculated on a ""dry"" basis and is not involved in the estimation of ventilation requirements."

Jun 1, 1947

By L. C. IlsLey

The Burrell methane indicator developed by Col. G. A. Burrell in 1915 was modified during 1918 to the " insulated type " Burrell indicator . Though this instrument has been used in mines since its first introduction , it was not formally approved as safe and efficient for use in gaseous mines until March , 1922. The indicator is built by the Mine Safety Appliances Co. , Pittsburgh , Pa . Approval No. 800 has been assigned to this company covering the device in the form approved . The principle of the Burrell indicator is fairly well known . It works on the same principle as the Haldane apparatus - measuring by means of a graduated scale , the contraction resulting from burning the methane content of an air and gas sample . A given aniount of the mine atmosphere to be tested for methane is taken into the indicator . This sample is then thoroughly shaken with the water in the indicator for one minute . The methane in the sample is now burned for two minutes by a heated platinum coil , which is energized by a small storage battery containing two Edison cells connected in series . After the glower or coil has burned for two minutes , it is disconnected from the battery , and the indicator is again shaken for The amount of contraction observed by reading the height the water rises in the U- tube of the indicator , which is calibrated to register the percentage of gas in the sample . The indicator as approved by the Bureau of Mines is equipped with an Edison M- 8 mine- lamp battery , and with a glass and scale graduated from zerɔ tɔ four per cent methane . The approval of a corbination service that is , an attachment for giving illumination from the same battery from which the platinum glower is operated has been withheld pending the development of a battery with larger capacity . - Under laboratory operating conditions , a single glower was capable of making at least 20 determinations if proper precautions were observed with respect to the use of freshly charged batteries . A battery should be allowed to stand off charge several hours before using in an indicator , as the peak voltage of a freshly charged Edison cell is abnormally high and is likely to send enough current through the glower to melt the platinum wire . Fifty-seven satisfactory operations were obtained from a completely charged battery . The point where the voltage of the cell fell below 2.3 volts with the glower attached was taken as the lower limit of successful operation . A voltage less than 2.3 does not permit the lower to burn at a temperature that will completely burn the gas in the air , thus giving a false indication .

Jun 1, 1922

By H. Tomlinson

The development of the Sevier Valley Coal Co.'s mine marks the opening of the Salina Canon coal district in Utah. The mine is favorably located with respect, to the existing markets of the West, and if the present estimates of the amount of workable coal in it are accurate it has many Important advantages in favor of its development. This mine is situated 18 miles east of the town of Salina, Sevier County, Utah, which at present is the nearest shipping point oh the Marysvale branch of the Denver & Rio Grande Western Railroad, and is about 152 miles south of Salt Lake City, which is the distributing center for much of the coal from the Carbon - Emery coal field and is the place from which nearly all Utah coal shipped to San Francisco and points on the northern Pacific coast has a common haul.

Jan 1, 1930

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

INPUT FORMAT INSTRUCTION FILE FOR PROGRAM MFIRE GENERAL RULES FOR DATA INPUT: $THERE IS NO NEED TO DISTINGUISH INTERGER AND REAL NUMBERS. $ $ SYMBOLS FOR NUMERICAL INPUT INCLUDE THE FOLLOWING $ $ 1234567890 -+BLANK $ $ * FREE FORMAT IS ALLOWED. COMMA AND BLANK SPACE CAN BOTH BE $ $ DELIMITERS. SEQUENTIALLY DISTRIBUTED BLANK SPACES ACT AS ONE $ $ DELIMITER. BLANKS ADJACENT TO A COMMA HAVE NO DELIMITING EFFECT $ $ * A ZERO INPUT CAN BE OMITTED BUT NOT THE DELIMITERS EXCEPT WHEN $ $ THE ZERO INPUTS ARE THE LAST ONES ON A LINE. $ $ * A LINE WHOSE FIRST NON-BLANK SYMBOL IS "$ IS AN INSTRUCTION $ $ LINE WHICH WILL BE IGNORED IN A PROGRAM RUN. $ $ * A LINE WHOSE FIRST NON-BLANK SYMBOL IS NEITHER ONE USED IN THE $ $ ABOVE LIST FOR NUMERICAL INPUT NOR "$, OR WHICH CONTAINS MORE $ $ THAN 3 SYMBOLS OUTSIDE OF THE LIST, IS A COMMENT LINE WHICH WILL $ $ BE SHOWN IN THE OUTPUT FILE. $

Jan 1, 1990

By James E. Mills

Coal, in the process of mining, transportation, and handling and on exposure to the weather, is subject to more or less disintegration. This disintegrated coal is usually called "slack" and amounts often to a considerable percentage of the lump coal produced in the mines. If this slack coal is wasted the loss so occasioned ranges from 5 to 50 per cent, or even more, of the total coal mined. It is therefore clear that the utilization of this waste slack coal becomes a serious economic consideration. When the coal is suitable for the production of coke, the utilization of the slack presents no difficulty, as it is in demand for that purpose. If the coal does not produce good coke, but cakes rather readily, the slack can be used for boiler purposes, as it fuses together more or less quickly, and burns on the furnace grate without great loss. Coal that cakes less readily can be burned on grates of special construc- tion. When so used it is more troublesome to handle, and the waste is greater than when lump coal is used. Consequently the price of much of the slack coal for fuel purposes ranges considerably lower than that of the lump coal from the same mine. The full value of this slack coal as fuel can be realized by first form- ing the coal into a coherent mass or briquet, such briquets, when of good quality, being equal to or of greater value than the original

Jan 1, 1911

Reduce longwall intake contamination by controlling respirable dust generated by the stage loader. Approach Install a water-powered scrubber on the stage loader immediately outby the crusher. Dusty air from the crusher is drawn through the scrubber and a clean air discharge is delivered into the primary face airflow. How It Works The contamination of intake air is a significant dust control problem often overlooked on many longwall faces. This dust source contributes to the full shift dust exposure of all face personnel, and thus can significantly affect compliance with Federal regulations. Several sources contribute to contamination; however, dust generated by the stage loader crusher is the single largest source. The breaking action of the crusher generates a tremendous quantity of dust, which mixes with the primary ventilation airstream and is carried down the entire length of the longwall face. The installation of a water-powered scrubber (see diagram) has proven effective in controlling crusher-generated dust. The scrubber is mounted immediately outby the crusher. A duct is placed over the scrubber intake and attached to a flanged opening over the crusher discharge. In

Jan 1, 1982

By W. F. Hughes

The thermodynamics of an electromagnetic field-fluid interaction system is discussed. A review of the thermodynamics of linear media (the permittivity and permeability taken as functions of density and temperature) is presented; then an extension is made to nonlinear media (the permittivity and permeability taken as functions of the fields). Expressions for thermodynamic properties and reversible work are derived and the first law of thermodynamics for magnetohydrodynamic flow is discussed.

Jan 1, 1968

By R. V. Ramani, C. B. Manula, A. Owili-Eger

Network analysis of mine ventilation systems is not new, having been traced back to 1854. A Committee Report (1970) has also reported the extensive work done in this respect in the United Kingdom, Japan, U.S.S.R., South Africa, United States, and other countries. Wang, et al (1970) developed a computer program which is an improvement over the earlier one developed by Wang et al (1967). The program has been recently modified and extended to include methane emission features by Owili-Eger (1973). This computer program incorporates all the novel features of the earlier programs. These include the capabilities of mesh selection, free splitting, internal or external fans, natural ventilation pressure and fixed quantity branches. The program is written in Fortran IV and, in effect, is an experimental mine in which many ideas can be tried out. The computer produces, besides the input data and certain computational data, the quantities and head losses in the branches, the head losses to be adjusted in the fixed quantity branches and the fan operating point. The last named program, hereafter to be referred to as the PSU/MVS, is presented in Appendix I. The application of this program is demonstrated in this manual through a series of selected examples. Application of the methane generator program is not included here as a detailed report on the subject is available elsewhere (Ramani et al, 1975).

Jan 1, 1975

By E. C. Bennett

"INRTODUCTIONVarious methods of making leakage tests have been tried during a study of losses in the transmission of natural gas. This work has been carried on by the Bureau of Mines in cooperation with the Natural Gas Association of America. Results of torts show that the ""shut-in -pressure-drop"" method described by Rawlins is the most accurate and reliable; therefore its use is recommended. This paper describes a graphic method for computing the rote of leakage from the fall in pressure and change in temperature determined by the ""shut -in pressure-drop"" method of testing.METHOD OF MEASURING PRESSURE DROPThe gas is ""shut in"" line to be tested and is not allowed to escape except through existing leaks. The leakage causes the pressure in the line to fall. The charge in pressure is obtained with a dead weight gage. Approximate results may also be obtained from readings on a good spring test gage. Numerous tests show that the dead weight gage is more sensitive to small changes in pressure than spring gages.The temperature of the gas in the line is observed simultaneously with each pressure reading. Temperature changes affect the pressure exerted by a given quality of gas ""shut in a line, end since the rate of leakage from a closed system is directly proportional to the rate of pressure drop, fluctuations in temperature must be considered."

May 1, 1926

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

4. Guidelines for Implementing the Emergency Escapeway Standards for Metal and Nonmetal Mines The technical discussion of each escapeway component precedes the specific guidelines for the component. Generally, the technical discussion provides the background and reasoning behind the guidelines. Section 5 is a discussion of general escapeway requirements, including the escape route, fire retardants, warning systems, ventilation systems, escapeway signs and signals, auxiliary transportation and fuel storage. The discussion is followed by a list of guidelines pertaining to the escapeways. Section 6 is a summary of the computer simulation of an escapeway system for Mine "C". A complete documentation of the simulation is included in Appendix A and B. Section 7 covers emergency hoisting requirements and concludes with the guideline, for emergency hoists, their inspection and use. Section 8 is a discussion of refuge chambers and life support and is concluded with guidelines for the application o f this equipment.

Jan 1, 1976

By Bruce T. Olenchuk, Wils L. Cooley

Electrical grounding is essential for the safe operation of power systems. A low-impedance path to ground is necessary to prevent the possibility of dangerously high potentials in human work areas. If for any reason this ground connection becomes faulty, a serious hazard may exist. One reason for faulty ground connections is ground bed corrosion. Corrosion of electrical ground rods has plagued the power industry and appeared in coal mine power systems. This paper will investigate ground rod corrosion, its cause, and possible solutions. Included is an evaluation of various ground rods for their ability to resist corrosion under stray current conditions. -The first known study of X-it3 Rod Corrosion is also presented.

Jan 1, 1979

By Oliver Bowles

This paper is the fourth of the current series issued by the Bureau of Mines on lime- plant problems . It is hoped that the information presented in these reports will develop sufficient interest among lime- plant operators to prompt them to discuss with the Bureau their own experiences , for it is believed by such an interchange of ideas conclusions will be reached that will be of practical benefit to the entire industry . Much valuable information has been obtained from replies to the papers already issued , but a more general response is greatly desired . It is hoped that many operators will contribute additions to the information on transportation systems now at hand by answering the questions on the final page .

Mar 1, 1923

By A. L. Pierce

This paper describing the mining practice at the Spring Hill mine of the Montana Mines Corporation, Helena, Mont., is one of a series issued by the Bureau of Mines on mining methods and costs in various districts. Its purpose is to summarize improved methods whereby lower costs have recently been obtained. These improvements are principally the adoption of a modified sublevel stoping method of mining the use of grizzlies underground improvements in haulage, and rage bonuses. The Sprint Hill, Trine is situated in Grizzly Gulch, 3 miles southwest of the city of Helena. Helena is on the links of the Northern Pacific and the Great Northern Railways; and the East Helena smelter of the American Smelting and Refining Co. to which the concentrates from the mine are shipped, is but 6 miles east of Helena. The mine is probing 150 to 200 tons of gold ore per day, with an underground crew of about 40 men.

Jan 1, 1931

By T. M. Barton

This paper presents several case studies in which a mechanics-based boundary-element program is used to back-calculate the surface subsidence associated with various panels at several northern Appalachian coal mines. The program used in this case study is called LAMODEL, which incorporates a frictionless, laminated overburden into a general-purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin-seam or vein-type deposits. In this paper, the program is used to calculate both the underground convergence and the resulting surface subsidence at five longwall panels and a room-and-pillar section. The fitted subsidence from the model is compared with the field measurements and analyzed. The results from this work show that the LAMODEL program is not as accurate as available empirical subsidence-predictive methods: the expected correlation between the geology and the optimum input parameters is not evident. However, for a mechanics-based program, LAMODEL does provide moderately accurate subsidence calculations, and it is one of a few programs that can even attempt to practically calculate both underground stress and convergence and the resulting surface subsidence.