Search Documents

By Fred N. Kissell

Methane-flow and pressure data taken from a mine in the Pocahontas No. 3 coalbed are compared with flow rates from lump coal obtained in laboratory experiments. From this, it is concluded that the main source of gas is the intact coalbed rather than a "crushed zone" near the working face. The permeability and sorption capacity of the intact coalbed are calculated and gas emission rates are theoretically accounted for.

Jan 1, 1972

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958

By EINAR M. ARENTZEN

This information circular. deais primarily with an engineering descrip- tion of a type of longwall cutting and loading machine developed by Eick- hoff Maschinenfabrik, Bochum, Germany..: This machine is supposed to have been developed and tested during the latter part of 1941 and early 1942. The only source of information is con- tained in certain literature and engineering data, with drawings which were acquired by the Allied Military Authorities when Germany was occupied; and the information will have to be limited because the writer has not seen the machine in the factory or in operation. However, the information may be of interest to the coal-mining industry in this country, and for this reason our Government has decided to publish the data procured so far. The Eickhoff cutting and loading machine is particularly suitable for the longwall mining system. It can only be used under that type of mining system and is not suitable for the more common type known in this country as room-and-pillar work. The material for the description of the machine and its operation was compiled and translated from German drawings and operating instructions. These detailed drawings and instructions are on file with the Bureau of Mines and are available for inspection by any responsible person interested in the details of the construction of the machine.

Dec 1, 1946

By W. E. Wallace, V. Castranova, P. Hathaway, F. H. Y. Green, E. D. Recad, V. Vallyathan, M. J. Keane

Inhaled particle contact with pulmonary surfactant in the hypophase lining pulmonary alveoli was modeled in vitro by exposing two respirable sized dusts, kaolin and silica quartz, to lecithin, a major component of pulmonary surfactant, emulsified in physiologic saline. Lecithin adsorbs to the dusts upon incubation at 37º C and suppresses their cytotoxicity as measured by pulmonary macrophage and erythrocyte assays, suggesting that pulmonary surfactant provides a defense system against prompt cell membrane lysis by inhaled dusts. Subsequent pulmonary macrophage phagocytosis and lysosomal enzyme digestion of the coated dusts was modeled in vitro by incubation with phospholipase A2 for one hour. With increasing lipase activity, silica hemolytic potential was restored to native silica levels. Kaolin was retoxified to levels far in excess of native kaolin hemolytic potential. Elution, thin layer chromatography and phosphate assay of treated dusts indicate most lecithin on silica is digested to lysolecithin and desorbed, silica retoxification being due to surface and adherent lysolecithin effects. Most lecithin on kaolin is not digested in this same time; that which is results in adherent lysolecithin which is responsible for the kaolin retoxification. Digestion with phospholipases A2 and C together produces only weakly retoxified kaolin. Results suggest that surface adsorption properties which control the adherence of prophylactic surfactant distinguish the pathogenic potentials of quartz, kaolin and mixed dust.

Jun 1, 1988

By D. A. Paice, A. B. Shimp

Illegitimate loads on a mine dc power distribution system can be detected by measuring a superimposed ac current. To implement such a scheme, a 10-volt, 3-kHz voltage is applied at each dc power substation. By this means, the mine dc power distribution network, consisting of a feeder and trolley wires with a grounded rail return, is caused to serve also as a 3-kHz ac distribution network.

Jan 1, 1975

By Fred N. Kissell

Methane-flow and pressure data taken from a mine in the Pocahontas No. 3 coalbed are compared with flow rates from lump coal obtained in laboratory experiments. From this, it is concluded that the main source of gas is the intact coalbed rather than a "crushed zone" near the working face. The permeability and sorption capacity of the intact coalbed are calculated and gas emission rates are theoretically accounted for.

Jan 1, 1972

By RUDULF KUDLICH

Pennsylvania anthracite coal is almost universally recognized to be the solid fuel best suited for domestic use when cleanliness , convenience and cost are considered . At various times and in various localities , however, conditions so affect the supply that it becomes insufficient or is too high in price and recourse must be had to other fuels as substitutes . In practically every district in the United States where anthracite has been the common domestic fuel , some other fuel is available as a substitute . In even the most severe climates such fuels are used either as emergency substitutes for anthracite , or as the ordinary domestic fuel . There may be some drawback to the use of such fuel , such as the need of more frequent attention to the furnace , smoke , soot and dust , in the case of solid fuels lower in price than anthracite , but these inconveniences must be accepted as necessary accompaniments to a decreased fuel bill . The cleanliness and ease of handling anthracite in the house must be considered in the light of a luxury and a higher cost of heating with this fuel must be expected . That a growing number of people are willing to pay for such added convenience is evident from the increasing mumber of heating installations using oil , gas and electricity , all of which are more convenient and usually more expensive even than anthracite .

Aug 1, 1923

By J. R. Katan, J. R. Ball, Peter R. Bannister, F. J. Williams

During the last week in March and the first week in April, 1973, the Naval Underwater Systems Center measured the 76 Hz magnetic field strength (in Wisconsin and Texas) produced by both the elevated and (newly installed) buried Wisconsin Test Facility (WTF) north-south (NS) antennas. The principle result obtained from these measurements is that there is no measurable difference in performance between the WTF buried and elevated NS antennas.

Jan 1, 1973

By Howard F. Puariea

This paper is one of a series describing methods and costs of recovering sand and gravel from alluvial deposits in the United States and deals directly with the methods employed by the Portland Gravel Co. in operating a clamshell dredge on the Willamette River near Portland, Oreg., and a pump dredge on the Columbia River near Vancouver, Wash. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local expenditures only and not total production costs. It is recognized that publication of total costs may in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By L. C. IlsLey, E. J. Gleim

It is the firm belief of the Bureau's engineers that the introduction of electrical mining machines has done much to increase safety in mining as a whole . There can be no doubt but that the substitution of machine mining together with permissible powder for the method of " shooting from the solid " has been the means of saving the lives of many shot- firers . Machine mining also leaves the roof in a better condition as lighter charges of powder are required to bring down the coal . Thus the danger from falls of roof are lessened . It is recognized that every effort should be made to prevent all accidents due to the use of electrical machinery but it is felt that any action tending to limit the use of such machinery would be a backward rather than a forward step in the safety measures laid out to decrease the hazards in coal mining .

May 1, 1920

By N. A. C. Smith

During the past, six, years, the Bureau of Mines has made and. published several hundred analyses of typical crude oils and 'has developed a system of interpreting the analyses and of classifying crudes. This system is presented here with. It is apparently equate for classifying crude oils into four main groups and has also been found very convenient in studying the geological relationships between crude oils, and the probable refinery yields of valuable products from them. Crude petroleum is morn to be a very complex substance. An analytical statement of its properties must, therefore, consist of two distinct parts, - first, the report of the results of the determinations made by the analyst in the laboratory, - second, the proper arrangement, classification and interpretation of these results so that the analysis, as a mole, will indicate the meaning- and the relative- importance of the essential characteristics of the oil.

Jan 1, 1927

By Foster Fraas

In this Bureau of Mines report, use of the photoemission of electrons to produce electric charges for the electrostatic separation of sonic dispersed minerals, which had previously been ground to pass a 43µ-opening sieve, is demonstrated. It appears that many of the oxides, carbonates, sulfides, and arsenides will respond to photoemission. Minerals least responsive are the oxides of silicon, the oxides of aluminum, and minerals that have a high concentration of these oxides. Although several synthetic ore mixtures did not yield to complete separation in a one-stage operation, it is probable that preliminary neutralization of the initial electric charges produced by powder dispersion will provide complete separation. That the separation can be carried out in air and without the use of reagents or heating, which are required in the present practice of electrostatically separating coarse granular feeds, is of special significance.

Jan 1, 1972

By Robert L. Lagace, Alfred G. Emslie

This report presents a mathematical model for the propagation of UHF radio waves in the large cross-section tunnels of a room and pillar limestone mine, and describes the analysis of a small amount of propagation data obtained in a limestone mine. The model and analysis is based on the waveguide mode theory developed earlier for the transmission of UHF waves in coal mine tunnels, with allowance for propagation losses due to refraction into the tunnel walls, to scattering by wall roughness, and to long range random tilt of the walls. Propagation around corners and through pillars is also examined based on a ray theory approach, together with the beneficial effects of placing reflectors at intersections to significantly reduce corner losses. The theory is found to be in fair agreement with the data; however, additional in-mine measurements are needed to provide a more conclusive test of the model.

Jan 1, 1979

GLOSSARY TERM DEFINITION ACCOMODATION The process by-which the eye changes focus from one distance to another. ADAPTATION The process by which the retina adjusts-to more or less light then it was exposed to during an immediately preceding period. Also involved, to a lesser degress, is the change in the size of the pupil which regulates the amount of light entering the eye. Adaptation results in a change in the sensitivity of the eye to light. CENTRAL VISION (FOVEAL) The seeing of objects in the central or foveal part of the visual field. It is approximately two degrees in diameter and permits seeing much finer detail than does peripheral vision. DIRECT GLARE The effect of brightness or brightness differences within the visual field sufficiently high to cause annoyance, discomfort, or loss in visual performance. FOOT CANDLE A measure of the amount of light falling onto a surface. FOOT LAMBERT A measure of the amount of light that is being reflected by a surface. GLARE The effect of brightness or differences in brightness within the visual field sufficiently high to cause annoyance, discomfort, or loss in visual performance. LAMP A generic term for a man-made source of light. By extension, the term is also used to denote sources that radiate in regions of spectrom adjacent to the visible.

Jan 1, 1976

By Marc T. Filigenzi

Two of the major ground control safety issues confronting underground mine operations today are shaft pillar stability and the failure of rock around active mine openings. Failure of a mine shaft can lead to the entrapment of workers. Failure of rock around active underground mine openings can lead to roof falls, which in turn can result in worker injuries and fatalities. Finite-element analysis has proven to be a reliable method for predicting stresses and displacements around underground mine openings. However, this is a complex and time-consuming technique and is not used as often as it could be in mine planning. The purpose of this paper is to demonstrate one technique developed at the Spokane Research Center that allows the user to create a finite-element model of a two-dimensional section of an underground mine in a relatively straightforward manner. This model is then used to calculate stresses, displacements, and safety factors around mine openings. With this information, mine planers can evaluate the stability of mine openings as well as the stability of pillars and mine shafts. This analysis will help develop mining sequences and layouts that minimize stresses in that section of the mine. This, in turn, should minimize the occurrence of shaft failure, roof falls, and other hazards associated with underground mining.

By Lloyd A. Morley, Alan M. Christman

General A review of the literature has revealed important areas which should be investigated during the field work. Of the utmost importance is the safety of mine personnel. Should a phase-to-ground fault occur on a shovel or other piece of equipment, current may return to the substation through the machine's contact surface with the mine floor, thereby raising the frame above ground potential and posing a shock hazard to anyone who touches the equipment. If the frame-to-earth resistance is very low, then no dangerous potentials will be developed, and a basis for elimination of the ground conductors from trailing cables could be postulated. However, should the contact resistance be high, then lethal voltages could be present on the machine frame. In this instance, low-resistance ground conductors in the trailing cable would be a necessity. Therefore, field tests should include measurements of the earth resistance of electrically operated portable or mobile mining equipment such as shovels, draglines, and drills. When the electrical distribution system is subject to lightning discharges, the grounding grid must safely carry to earth and dissipate enormous current surges. It is essential that the grounding grid have a low value of earth resistance, because any potential developed across the grounding grid as a result of current flow will appear on the frames of all machinery connected to the grid. Thus, an earth resistance

Jan 1, 1976

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

Information is presented on remote sealing of a mine passageway through a borehole by five methods : PPnneeuummaattiicc injection of mineral wool and sand, ureaformaldehyde foam , balloons , urethane foam, and caving by blasting . An adaptation of the method using pneumatically conveyed mineral wool was tried in an operating mine . Further research is needed to simplify and to improve the techniques involved , as well as to explore the possibilities of other methods and combinations .

Jan 1, 1964

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

The computer program has been developed in conjunction with the rest of the project to evaluate evacuation capabilities of the mines and develop guidelines for the escape systems. There are several problems associated with predicting evacuation performance of a mine. First, the mine has many interconnected passages, shafts, hoists and a number of miners in varying positions. To be able to predict evacuation time requires processing a hugh amount of data. A simplistic approach of determining the miner farthest from the exit and calculating evacuation time for him knowing his walking speeds and hoisting times is not realistic, since the waiting time for the hoist is neglected. The second problem is being able to repeat the calculations for a number of configurations. It may be possible to spend enough time to hand calculate the evacuation parameters for a single mine for a single configuration, but to evaluate capabilities of the evacuation

Jan 1, 1976

As technology evolves, accidents may occur because human-system interactions were not considered adequately in the process. A systematic methodology can be used to evaluate the causes of mishaps and to develop recommendations that will enhance safety. A recent trend observed in underground coal mining is used to illustrate this principle because an underground mine is a dynamic work environment. Mining is characterized not only by frequent geologic changes but by technological evolution that can seriously degrade human performance and compromise worker health and safety The case exemplified in this paper involves implementation of remotely controlled equipment for extended cut mining. Extended cut mining technology evolved with minimal ergonomic consideration even though the change from on¬board to remote machine operation dramatically modified the role of the human component. In response to concern that system interactions should be examined more closely. a methodology was developed to identify hazards.

Jan 1, 1998

By George J. Conroy, Angel G. Jordan, Eugene W. Bartel

Time-domain reflectometry has long been an accepted and used method for locating electrical faults in electrical cables. The process has, however, required the use of equipment that is somewhat complex and difficult to use. The skill level needed to operate such equipment is high. Therefore, the use of the time-domain reflectometry process has been limited to selected locations and controlled environments. The process, however, has great potential for mine system applications. The ability to locate and repair trailing power cable without removing it from the mine would result in great savings in cost and employee-hours. Therefore, an automatic microprocessor-controlled time- domain reflectometry system was developed to reduce process complexity and skill level needed to operate the unit. The theory of operations is discussed along with the computer analogies used in the unit. The present unit capabilities are presented and future areas of application and research are discussed.

Jan 1, 1979