Search Documents

By E. R. Spencer, E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. In response, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been conducting a cross-sectional survey of equip­ment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by dredging. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to iden­tify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges used in several surface mine sand and gravel operations and in the processing facilities. Results indicate that there are areas on the dredges (crane, suction pumps and diesel engines) where sound levels greater than 90 dB(A) are pres­ent. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration’s (MSHA’s) permissible exposure level (PEL) of 90 dB(A) eight-hour time-weighted average (TWA8), laborers, mechanics, oilers, helpers, pickers and greasers are the workers most likely to be exposed to hazardous sound levels and to thus develop NIHL over time

By A. C. Smith

The U.S. Bureau of Mines constructed a large-scaJe facility to study the self-heating of a large coal mass under conditions that simulate a gob area of a mine. The insulated coal chamber can hold up to 13 short tons (st) of coal and is provided with a forced ventilation system and computer-controlled temperature and gas measurement systems to monitor the heat and mass transfer phenomena that occur in the coalbed. Three experiments were completed with high-volatile C bituminous coals that exhibited high spontaneous combustion potentials in laboratory-scale tests. In the first two tests, a sustained heating was not achieved. In the third test, temperatures throughout the coalbed increased steadily from the start, with thermal runaway occurring near the center of the coalbed after 23 days. The thermal reaction wne then moved toward the front of the coalbed. The results of these tests showed that the self-heating of a large coal mass depends not just on the reactivity of the coal, but also on the particle size of the coal, the freshness of the coal surfaces, the heat-of-wetting effect, and the availability of O2 at optimum ventilation rates.

Jan 1, 1991

By John D. Warne

"INTRODUCTION Initiated as a part of the Bureau of Mines program for development of strategic minerals for national defense, Investigation of the fluorspar deposits of the Northgate area was begun in June 1944 and completed in March l946. Mining Operations were active in the district during most of the period of investigation.The Fluorspar, Fluorine, and Camp Creek mines develop the two more promising vein systems known in the area, the Fluorspar group of claims covering one vein system and the Fluorine and Camp Creek groups the other. Figure 1 shows the location of the properties. The Fluorspar and Fluorine properties were operated (except during the winter months) by the Western Fluorspar Corp. The Camp Creek mine was operated during 1943 and 1944 by Kramer Mines, Inc.The properties were examined April 20 and again November 4 to 12, 1943, by C. R. Wilfley, a Bureau of Mines engineer, who recommended work to determine ore reserves and to serve as a guide for development. Investigations by the Bureau of Mines covered all three properties."

Aug 1, 1947

By J. P. Morris

An experimental blast furnace in normal operation was quenched by substituting cold nitrogen for the hot blast air. More than 2,200 samples from the stack, bosh, and hearth were taken; 500 of these were selected for detailed analysis. Deductions are made as to the patterns of burden movement and gas flow; the reduction of iron oxides, including a comparison of ore and sinter; and the behavior of sulfur above the smelting zone. Metal and slag beads from the bosh were analyzed, as were samples from the hearth metal and slag. A brief description of a petrographic examination of the quenched burden is included.

Jan 1, 1963

By Bryan Buchholz, N. Kumar Kittusamy

Previous studies indicate that operators of heavy construction equipment are afflicted by musculoskeletal injuries of the arms, shoulders, neck, and lower back. These injuries appear to be due to excessive periods of sitting (static posture), work intensity, whole-body vibration, high resistance levers, repetitive motions, and awkward postures. (2-5) Although numerous studies have shown an association between operation of heavy construction equipment and symptoms of musculoskeletal disorders, very little research has been performed that systematically characterizes operating engineers' exposure to ergonomic hazards. The objective of this study was to systematically characterize the ergonomic hazards associated with excavating operations. As such, the following were performed: (1) vibrations were measured at the operator/seat interface (X, Y, and Z axes), and at the floor of the cab (Z axis); (2) psychophysical ratings of whole-body vibration (WBV) level and overall seat design were obtained; and (3) postural assessments of the job were made. Methodology This study evaluated an inexperienced female operator performing excavation, utilizing two different pieces of equipment. The operator was 37 years old, 162 cm tall, and weighed 80 kg. She had approximately 15 hours of operation time (experience) on the equipment evaluated. The two pieces of equipment used were: a Case Super 580E (1986) backhoe/loader, and an Insley H-2000 excavator (1975) (see Figures 1 and 2). More evaluations were performed on the backhoe/loader than on the excavator. The following evaluations were performed on the Case equipment: 1) vibration levels at the seat and floor; 2) psychophysical ratings of the overall seat design and vibration levels (for the task duration, and for an 8 hour duration); and 3) postural assessments. For the Insley equipment, all of the evaluations were performed except vibration measurements. When the evaluations were conducted, the following environmental conditions were noted: the temperature was 31°F, and soil and terrain conditions were rough and frozen.

By R. S. Dean

"Interest in the nitrogen content of steel has increased sharply in the last few years. Investigations have indicated that its presence in steel has an important bearing on high temperature brittleness3, magnetic properties4, room temperature hardening5, and shock resistance. The steel producer may therefore look forward with certaintly to the necessity of controlling this element in a considerable proportion of his product. The literature, however, reveals a great many contradictory statements concerning the percentage of nitrogen which must be present to produce given effects on the properties of iron and steel. Most of these arise from a misunderstanding of the nature of the iron-nitrogen diagram near the iron end and a lack of recognition of the effect of state of aggregation on physical properties although both have been fairly well worked out.My thanks are due to Mr. J. L. Gregg, Prof. R. H. Dowdell, Mr, R. F. Mehl and Mr. H. C. Vacher for suggestions in connection with the preparation of this paper, and to Mr. C. H. Hefty and Mr. G. T. Motok for furnishing a valuable bibliography and translations of articles by Must and Duhr.The iron-nitrogen diagram in the solid state, so far as it concerns the nitrogen content of commercial iron and steel, consists simply in a solubility curve increasing with temperature. The important thing about this solubility curve is that without cold wore the iron nitride when precipitated does not go into solution on heating for long periods below 300°C. This slowness of solution is probably due to the fact that iron nitride when present as a separate phase has at these temperatures an equilibrium pressure of several thousand atmospheres7 and that therefore each particle of iron nitride surrounds itself with a layer of nitrogen. The precipitation of such an unstable crystal presents points of interest thermodynamically but we can not go into these here. It is quite well established that it precipitate. It can not diffuse then unless this layer is broken through or the temperature and pressure are increased to a point where the nitrogen is absorbed at an appreciable rate in the surrounding iron. This rate will depend on the degree of unsaturation of the iron and the excess pressure of the nitrogen above equilibrium pressure. The degree of unsaturation is determined by the temperature alone so that the temperature at which the rate of solution of the nitride becomes appreciable will depend on the pressure of nitrogen developed. This, in turn, will depend on the balance between rate of decomposition of the nitride and the rate o: flow of the iron. In annealed iron, this temperature of appreciable solution rate is between 300 and 350°C.8 By cold work, however, the elastic limit of the iron is increased, and conditions for the nitride to go into solution are reached at a much lower temperature, giving rise to the so-called blue brittleness. This brittleness and hardening is due to iron nitride going into solid solution and is not precipitation hardening."

Mar 1, 1931

Mineral production was of little significance in the country's economy, and Bangladesh was not a world-ranked producer of any mineral commodity during 1977. Natural gas was the most important mineral exploited; however, reserves were sufficient to allow for much greater production, Economically, Bangladesh made some progress in 1977-782 in its struggle against poverty, underdevelopment, and rapidly increasing population. The gross domestic product (GDP) grew 8%, mainly owing to a 13% increase in food grain production, the key economic indicator in this highly agricultural nation. GDP at current prices dropped slightly in Fiscal Year (FY) 1976.77 to $6.6 billion3 and rose to $7.2 billion in FY 1977.78. The population rose from 81 million in FY 1975-76 to about 85 million in FY 1977-78, resulting in an increase of per capita GDP from $83 to $85 during the same period. The high annual population growth rate, over 3% in 1976 and about 2.8% in 1977, was recognized by the Government as the main problem facing the country. Average density was 525 people per square kilometer. A similar density would have the entire world population living within the continental United States.

Jan 1, 1981

By M. A. Trevits, I. R. Houlison, A. C. Smith, T. P. Mucho

Timely and rapid intervention to underground combustion events (fires, explosions, and spontaneous combustion) is the key to the successful control of the mine atmosphere and restoring of a coal mine to production. The focus of this paper is the utilization of a GAG 3A jet engine system to combat either large out-of-control fires or to render an entire mine inert when access to problem areas is difficult or impossible. This system is based upon a Soviet designed agricultural jet engine which consumes aviation fuel with oxygen (O2) from the intake air and exhausts combustion gases, primarily carbon dioxide (CO2) and water (H2O), along with the nitrogen (N2) from the air and small amounts of carbon monoxide (CO) and hydrogen (H2). The system is designed to approach stoichiometric combustion (ideally, pure burning that scavenges all the oxygen from the intake air). Therefore, these exhaust gases are almost entirely “inert gases”- i.e., gases which do not contribute to, and in fact, can suppress the combustion process due to the lack of oxygen. Other methods to inert mine areas have been used in the US and internationally, but these methods usually use low flow inertisation equipment or methods. Use of these low-flow inertisation equipment and methods has been successful in proactively rendering gob areas inert and has the ability to inert the entire mine workings. Due to the low flow rate, however, a substantial period of

By Gerald T. Homce, James C. Cawley

Electrical arcing injuries are the most common form of electrical injury in mining. MSHA data show that 381 "non-contact electric arc burn" injuries occurred in the mining industry from 1996 - 2005. A more detailed study of data from 1990-2001 showed that five types of apparatus - circuit breakers, conductors, nonpowered hand tools, electrical meters and test leads, and connectors and plugs were involved in two-thirds of the lost workday injuries. Many of the protections from electrical arcing injury available to workers in other industries stem from the application of National Fire Protection Association Standard 70E - Standard for Electrical Safety in the Workplace (NFPA 70E). NFPA 70E is a generally accepted industry guideline document, but excludes underground mining from its scope. Many of its practices and procedures, however, can be applied in the mining workplace to supplement the existing electrical safety requirements of Title 30 Code of Federal Regulations. This paper describes how NFPA 70E can be applied to mining workplaces after an analysis of the mine power system electrical arcing hazards has been completed (and Hazard/Risk Categories determined) using the tables from NFPA 70E or the calculation method as described in IEEE 1584. NFPA 70E can then be used to determine the levels and types of personal protective equipment (PPE) needed to protect miners against burn injuries. Appropriate lockout and tagout (LOTO) procedures for use in the mining industry are also described. Suggestions for better selection of electrically-rated hand tools are included. Recommendations for electrical meter selection and use based on transient withstand capability are also discussed.

By I. Liebman

The Bureau of Mines conducted experiments on coal dust explosion suppression. The investigation took place on a beltway in the double-entry of the Bureau's Experimental Mine. Using conditions that simulate those in a working mine, the investigation showed that a coal dust explosion can be readily initiated in a conveyor belt entry. Also, the explosion can spread into adjacent entries through opened crosscuts (stopping destroyed by explosion) to propagate for long distances even though the adjacent entries are rock dusted in compliance with regulations. Passive water barriers (water-filled tubs) were found to be effective in suppressing explosions on a beltway; however, barrier efficiency was reduced by opened crosscuts. The study indicated that the beltway barrier should be the distributed type consisting of continuous rows of water-filled tubs covering long distances along the entry. A plan is outlined for the installation of a water barrier system in a working coal mine for the protection of a beltway.

Jan 1, 1981

By C. R. Summers, J. N. Murphy

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneurnaric drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115 -dbA s rope drill to approximately 100 dbA.

Jan 1, 1974

By C. Ogasawara

This document describes the direction and progress of the Bureau of Mines Oil Shale Mining Environmental Research Program as of January 31, 1979. It is aimed at focusing the Bureau's role in environmental research supporting oil shale development with respect to the activities of other involved government agencies and private industry. Environmental considerations in oil shale extraction, such as ecological disturbances, health and safety hazards, waste management, and socioeconomic impacts, are discussed along with the type of research known to be planned by organizations to ameliorate these problems.

Jan 1, 1979

By Michael G. Zabetakis

Limits of flammability of normal propyl nitrate (NPN) vapor were investigated at ambient and elevated temperatures. Minimum spontaneous ignition and decomposition temperatures were determined with laboratory apparatus over the pressure range from 0 to 4,000 p.s.i.g. Flame speeds and the detonation susceptibility of NPN vapor were measured at elevated temperatures. Stable detonation was obtained with liquid NPN at elevated temperatures, and the detonation velocity was determined to be between 4,700 and 5,100 m./sec.

Jan 1, 1962

By Donald W. Mitchell

Research shows that water neutralizes the explosion hazard of coal dust when present in sufficient quantity and when intimately mixed with the dust. The quantity of water required to neutralize coal dust and coal-rock dust mixtures is about equal to the limiting moisture adsorptive capacity of the dust; the adsorptive capacity increases with increase in the fineness and volatile content of the coal. Pools of water or high atmospheric humidity do not reduce the explosion hazard. Although wetted dust is less dispersible than dry dust, poor dispersibility cannot be relied on as the sole safeguard against explosion. Dust mixtures that contain water in excess of their limiting adsorptive capacity are dispersed and ignited by severe initiation sources. Pure coal dust adsorbs water with difficulty and retains water poorly; adsorption and retention is increased by the addition of rock dust the coal; the rock dust agglutinates wetted coal and assures that incombustible is present should drying occur. Therefore, it is advantageous to rock-dust wet areas in bituminous coal and lignite mines. When coal-rock dust mixtures are wetted and subsequently dried, the explosion hazard is about the same as for dust which was not wetted.

Jan 1, 1962

By G. L. Oldright

The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada, Ltd., Trail (Tadanac), British Columbia. Many thanks are due to S. G. Blaylock, vice president and general manager, James Buchanan, smelter superintendent, and George Murray, assistant smelter superintendent, for their broad general policy in permitting these data to be taken and published. life are also grateful for the help given by the staff members stated in Paper XI, Report of Investigations Acknowledgment is given several excerpts from experiments by F. E. Lee, head of the research staff. INTRODUCTION The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of lead-rich slags, of viscous slags, and. of low capacity in smelting.

Jan 1, 1934

By S. Gallagher, A. G. Mayton

Back injuries account for a high proportion of lost workdays in the mining industry and are a leading cause of disability in mine workers. Two risk factors for low back injuries are manual lifting and whole-body vibration exposure when operating mobile equipment. Recent research has shed light on possible mechanisms through which low back injuries may occur, and the results of these studies can be used to improve the design of lifting tasks and seats to decrease injury risk. This article discusses recent research results and how this knowledge can be leveraged to reduce the risk of low back pain.

Provide the U.S. mining industry with technology for designing environmentally sound, low-cost in situ leach mining operations to produce copper from small, deep, and/or low-grade copper oxide deposits. Approach Investigate the feasibility of a new mining method--in situ leach mining-as an alternative to conventional mining for copper. Study fundamental leaching technology that will facilitate future commercial operations. Develop guidelines and procedures that will enable mine operators to design and evaluate in situ leach mining operations for any specific copper oxide deposit.

Jan 1, 1989

By Richard Havens

Acidic and basic uranium leach plant residues located on the Navajo Indian Reservation, Tuba City, Ariz., were successfully stabilized against wind erosion using a relatively low-cost chemical method. An elastomeric polymer chemical was applied to the dike areas and a calcium magnesium lignosulfonate to the beach areas of three tailings ponds. The water-soluble chemicals were applied with an automated sprinkling system. The stabilization cost was $335 per acre for the 34.5-acre tract.

Jan 1, 1969

LARGE-SCALE production of zirconium by the Northwest Electrodevelopment Laboratory of the Bureau of Mines at Albany, Oreg., is an anomaly that justifies some explanation. The reduction of titanium tetrachloride with magnesium in an inert atmosphere, as perfected by Dr. W. J. Kroll before 1940, aroused renewed interest in zirconium, and in 1945 development work on this metal was initiated at Albany under Dr. Kroll's technical direction. Preliminary results were promising, and in February 1947 a pilot plant with a weekly capacity of 60 pounds of zirconium-metal sponge was put in operation. Shortly thereafter the Oak Ridge National Laboratory of the Atomic Energy Commission requested production of 1 ton of zirconium-metal sheet, with the provision that it have a low hafnium content. The Bureau of Mines was furnished with a. supply of Brazilian baddeleyite ore, containing less than 1 percent hafnium with respect to zirconium, from which was made about. 2,700 pounds of relatively low hafnium zirconium sheet of 0.080-inch thickness for test purposes. This was accomplished by melting zirconium sponge in a graphite crucible, hot-rolling the ingot in an iron sheath, and finishing by cold rolling. Concomitantly the Oak Ridge Laboratory developed a method for separating hafnium from zirconium; and, in cooperation with the Atomic Energy Commission and the Bureau of Ships of the Department of the Navy, a, larger pilot plant was erected to produce zirconium from very low hafnium zirconium tetrachloride furnished by the Commission. Pilot-plant work on producing zirconium tetrachloride from zircon sand and baddeleyite was discontinued. Production of zirconium sponge in the larger pilot plant of 500 pounds per week capacity was begun in June 1949.

Jan 1, 1956

"INTRODUCTION Industrial utilization of the present submarginal domestic manganese resources of the United States is wholely dependent at this time on the electrolytic manganese process established as the result of 4 years of continuous operation of the Bureau of Mines pilot plant at Boulder City and 7 years' operations of the Electro Manganese Corporation commercial plant at Knoxville, Tenn.Three Kids ore provided the feed for the Boulder City pilot plant during 3 years of operation. Hence, the electrowinning characteristics of the ore have been thoroughly established, making possible accurate estimates for commercial operations.Before the Defense Plant Corporation constructed the leaching plant, the Bureau of Mines conducted an exploration project to determine the extent and grade of the ore reserves. Additional exploration, development, and mining by the Manganese Ore Cc, have accurately determined the tonnage and grade of ore. A large tonnage of stock piled ore is now available for immediate processing, and a considerable tonnage of openpit ore has been stripped of overburden preparatory to mining. Numerous facilities, such as power, water, and housing, needed for an electrolytic manganese plant are already available.All of these factors, as well as plans for installation of scale electrolytic manganese plant facilities, are presented in detail in the chapter entitled, ""Mining and. Electrolytic Reduction of use from Three Kids Manganese Mine."" The Manganese Ore Co. kindly provided information on the present ore reserves and state of development of the mine."

Jun 1, 1945