Search Documents

By Parley Potter

GENTLEMEN OF THE COAL MINTING INSTITUTE: I was requested to write an article on mining a short time ago; however, the time has been so short that I have not had time to prepare an article as I would like to have presented it to this body. In writing this article it has not been my intention in making comparison of various mines, to favor one or discredit the other. I hope it will be considered in that light. The coal mining industry as I have seen it in the past, at present and in the future. In years gone by large tracts of coal land could be obtained at a very small cost, and as yet coal land may be purchased at a reasonable price in this country, but I believe the time is near at hand when the methods of mining will have to be changed greatly in this country. Many changes have taken place-in the last few years, some of them have been forced by law, others by the coal operators themselves, after being convinced that the changes made were for their own benefit. During my 20 years in the mines I have seen thousands and thousands of tons of coal lost that could have been saved if proper methods of mining had been used. The Room and Pillar system of mining coal is none. too good at its best ; a certain per cent of the coal is always lost, yet it is about the only system that can be used under certain conditions, but where the Longwall system can be used I believe it is the best system yet introduced. If the Longwall system is used' there is no coal lost. You get it all as you advance with the workings. Some coal operators object to the Longwall system for several reasons, and most of the reasons they advance are not founded on facts. For instance some of them claim it is too expensive. I will admit that the cost per ton is a little higher in Longwall than it is in Room and Pillar as a rule for the amount of coal' mined, but after the Room and Pillar mine is finished as a rule there are thousands of tons of good coal lost, for the simple reason that it cannot be mined at a profit. In many cases if the same mine had been operated on the Longwall system every ton of saleable coal could have been mined at a fair profit, and in the long run would have netted the owner much more money than it did under the Room and Pillar system. The Longwall system has been in operation many years in Europe and especially Great Britain, and is the most approved of systems in many countries at the present time. Millions of tons of coal have been saved by its use in those countries. It is claimed that the Armour Packing Company loses nothing but the squeal of the hog when it is killed, and doesn't allow it to squeal much. Why lose coal if the Longwall system of mining will save it? The Longwall mine is far more easy to ventilate than the Room and Pillar mine; the air has a much less distance to travel for the same amount of working face in Longwall than it has in the Room and Pillar.

Jan 1, 1921

By R. Dawson Hall

R. DAWSON HALL (The Coal Age, New York City) : Mr. Chairman and gentlemen: I do not feel that I have anything in particular to say. I have not prepared anything for an occasion such as this. I just came from New York City, and as one man said to me today, "That is not any recommendation in particular." (Laughter.) In answer to your request for a few remarks of a timely character I would say: One of the possibilities in the Rocky Mountain Region coal mines is the use of steel arches, posts and straps. The timber of the region seems unusually subject to dry rot and does not last long, especially in those places as in southern Wyoming, where the mine atmosphere is likely to contain a large quantity of carbon dioxide. It is true that, in many mines, much care is taken to drive out this gas and to arrange that the timber will have the fresh air that will prolong its life, but despite such provision much timber is subjected to speedy rot. Steel has made rapid progress in England, Germany and France and is recognized as an economy, not an extravagance. Frequent replacement of rotting wood and removal of broken rock are a source of great waste, risk and inconvenience in operation that together spell great cost. The very dryness of the mines and the lack' of acid water are favorable to the use of steel where support of roof or sides is necessary.

Jan 1, 1932

By James F. Howe

Modern civilization is centered around a small group of essential occupations, the three principal ones which are agriculture, mining and manufacturing. Agriculture might be called the most important of the three, as it has to do directly with the supply of food for the human race. Mining, however, is certainly next in importance, as it furnishes the supply of fuel and many of the raw materials used in manufacturing. Without mining, modern machinery and many industrial operations would be impossible. Mining takes advantage of the, natural resources in fuel and minerals that lie underneath the surface of mother earth, and while at times some of these metals are hard to find and mines come and go, mining must continue to increase. Mining is no longer a haphazard proposition but one calling for careful study and complete plans of operation for years to come. The shafts, power houses, rock dump crusher, concentrator, and other machinery must be located advantageously in order to enable owners to make a profit. Many tons of rock or mineral must be mined frequently to get one ton of concentrated metallic ore or metal itself. Economy in mining is just as essential as it is in manufacturing. The mining engineer of today is called upon to utilize every branch of engineering, and not only, is a wide: range of knowledge required, but ingenuity to meet the unusual conditions which are constantly arising from week to week. On account of the wide variety of information required by the mining engineer, some things with which he is in almost daily contact may be passed over with only a small amount of attention, provided everything is going well, in order that time and attention may be focused on what might be termed the more important features of mining operations. Because competition has become keener than ever, owing to overproduction at times of certain minerals, it becomes a matter of first, importance to understand as far as possible the factors which enter into the cost of production of any mineral which may be mined. In such times of overproduction, the high cost mine is forced to close down while the low cost mine may, if desired, be kept running constantly. In keeping a cost record, wire rope on account of its high first cost 19 coming into the lime light, and a comparison of records of one mine with another is now frequently made in order to see whether the rope service is satisfactory or not. Every rope maker, on the other hand, is interested in seeing that the rope which he produces gives the maximum possible return for the money invested. Modern mining owes much of its success to the use of wire rope for hoisting materials from beneath the surface of the ground. Deep mining would be impossible without the use of wire rope as a means of hoisting. A study, therefore, of rope problems in mining work and a discussion of the points which are beneficial to maximum life will enable the mining engineer, manager, or superintendent to keep his costs down to the minimum while at the same time he provides a suitable and sufficient safety factor for operations at all times. Mining might be defined as the extraction of coal, metallic ores, or minerals from below the surface of the ground. This definition does not cover what is known as, open pit operations or quarrying but covers the

Jan 1, 1922

By P. F. Patterson

It is a well established fact that 60 per cent of all accidents in coal mines occur from falls of roof and coal at or in the proximity of the working face. Notwithstanding that this is well known, and has been frequently discussed by mining men, this seems to be the irreducible minimum. It is even said by those in a position to know that the percentage stated is increasing. With this, information before us it would seem that not enough attention is being given to close supervision at the working face, and until this is done we may expect to continue experiencing an increase in the accidents in this area. No workman generally feels that it is more important to finish loading a car of coal than to set a timber for protection, and many accidents happen from this source, not from a lack of knowledge of the dangerous conditions existing, but negligence in taking remedies necessary to remove the danger. It is true that nearly all state laws require the mine foreman or his assistant to visit each working face every day, but with the constantly changing conditions on account of the advance of the working faces, these daily visits may be entirely inadequate to discover possible dangers and prevent accidents. The obvious remedy then is closer and more systematic inspection and supervision of the working faces. Many accidents are caused in mines on account of not enough clearance between the rib and track or between timber and track. On all main haulage ways. there should be a space of at least 30 inches between the rib and track, or timber and track, and on all rooms not less than two feet should be left between the track and upright timbers.. A great deal has been said and written with regard to systematic timbering. We doubt very much the feasibility of adopting any standard of timbering that would be suitable for all roof conditions, and any such system in our opinion would not tend to cause a decrease in the number of accidents. The proper place to put up a prop, regardless of whether it conforms to any established system, is under a piece of loose roof. No habit is becoming more prevalent among miners and other mine workers than wearing gloves, principally flimsy canvas gloves, which afford no protection to the wearers and are the direct cause of many hand injuries. If gloves must be worn, and no doubt they will be as the habit has become well established, then they should be made from some heavy material and should fit the hands fairly snug.

Jan 1, 1923

MR. GIBSON (continuing): In connection with the coal from this mine, I will say that it is not a very dirty coal. The vein where most of the coal comes from is about eight feet thick, and two feet from the bottom there is a small boney band about two inches thick. The breaking shot has to be placed over the, band, therefore breaking the boney into fine particles which goes off with the slack. This coal is a very good domestic coal and the slack is in great demand for various power, plants, such as sugar plants, smelters and other industries, but where this, boney is broken up and goes into the slack, it is very injurious in effect and retards the sale of the slack. Therefore the Spring Canyon Coal Company went to the expense of' building this plant, costing over $250,000, just in order to get that, two inches of boney coal out of the rest of the vein. The market in, Utah is very critical, and in order to sell coal, the product must be thoroughly clean in every way and, as Mr. Murphy says, I believe they have succeeded in making a very good commercial product. In any event the Spring Canyon Coal Company put out more coal than any other one mine during the last year, 1924, they had the largest production. I thank, you. (Applause). PRESIDENT MARKS: With the assistance of Mr. Robinson and Mr. Miller, I am sorry you could not get the pictures a little better synchronized with the story. MR. F. C. MILLER (Chief Chemist The Colorado Fuel & Iron Company, Pueblo) : We had seven slides to show eighteen different views on the screen and we did remarkably well. (Laughter.) PRESIDENT MARKS: Is there : any further discussion on this paper? MR. G. B. JONES (Mining Inspector, Victor-American Fuel Co.) : I would like to ask a question on the

Jan 1, 1926

By George B. Pryde

Dear Sir: Yours of July 23rd, relative to my appointment on the Safety Committee in connection with the Rocky Mountain Coal Mining Institute. As you say in your letter, "The duty of this committee is to draft suggestions as to safer mining practices with the idea of preventing disasters in coal mines." Much has been written and many suggestions made on this same subject, and it is very hard to put up further recommendations than have already been made. The disasters you mention in your letter unquestionably have direct reference to coal mine explosions, which from time to time still occur in this and other countries. As far as our Western mines are concerned, you know that sprinkling and shot firing by electricity have been very extensively carried out. Notwithstanding these precautions; we have had a few rather serious disasters in the past in these mines. I do not care to place any blame or responsibility on the companies having these disasters, but it is a fact that in each and all of them, after careful investigation has been made, that the human element has had more or less bearing on the accidents happening. From most reports that we gain, either directly or indirectly, it is very evident that investigation shows after an explosion that the rules governing one or both of the above safety measures have been somewhat carelessly or negligently carried out. Much has been written and read about rock dust sprinkling, but it is questionable if this method is doing a great deal toward the eliminating of disasters. While it is true it may have the effect of preventing propagation, still I do not believe anyone claims for it a sure preventative against initial explosions. I had occasion not long ago to visit a mine, after an explosion, in which dust barriers were supposed to be hung, and from indications it was quite evident that the dust barriers had been in operation, but they did not prevent the explosion from reaching all open parts of the mine. It is also true that profuse scattering of rock dust throughout a mine would have a beneficial effect, but there is a question arises here as to whether the sprinkling by rock dust or the spraying by water, if available, is the most effective. I am satisfied that if all coal mines are kept well sprinkled and all open workings maintained in a thorough moist condition, that the biggest factor in a coal mine explosion is in this way eliminated. There is no doubt but what the use of permissible powder, particularly if shot by electricity, has had a very marked effect on the number of disasters in mines, and if this method of shooting was energetically carried out there would be a difference in the number of explosions, both minor and Major, all over the country. Some of the recent explosions have taken place where no shooting was being done, but there is no denying the fact that the other ingredient, namely, coal dust, entered in the elements very extensively. We have read and heard of hydraulic cartridges and other patents (substitutes for powder) that were being worked out for the purpose of

Jan 1, 1923

By H. F. Nash

Coal is the basic necessity of our present-day civilization, and those engaged in the industry, whether miner, day-man, pit boss, tipple boss, superintendent, salesman or operator, have a direct responsibility to the public at large. Our country is blessed with a great supply of Bituminous coal, upon which it must largely depend for its industrial prosperity. Anthracite coal, in its relation to our economic situation, is a small factor, as its ratio of production to Bituminous coal is only about one-sixth. However, within the last ten years, electricity and oil have largely displaced the use of coal in industry, so that the use of Bituminous coal is decreasing, relatively, and the potential production of Bituminous coal has largely increased since the war. High wage scales and high freight rates make the delivered price of coal to the consumer so out of proportion to the cost of electricity and oil -and strikes make the supply of coal so uncertain-that industry is rapidly turning to electricity and oil. The energy in a ton of coal can be transported, by electric current, a distance of 250 miles for 78% of what it costs to ship the coal in bulk, by rail, in the East-and, for about 60% of what it costs in our section of the country. The use of fuel oil, distillate and gasoline, in industry, has increased by leaps and bounds. Especially was this noticeable during the strike this year, as the large packing plants in Kansas City, Omaha and Sioux City (that formerly used nothing but coal) are now practically all using oil. This also supplies to other industrial plants throughout our territory in Texas, Oklahoma, Kansas and Nebraska. Many railroads are using oil, as are also the smelters, cement plants, etc., etc. Ten years ago, 100% of the threshing in the state of Kansas was done with coal-today not over 25% of it is done through that means-and so it goes all along the line. The use of our coal is being yearly more restricted in industry. In the case of domestic consumption, the circle is also ever decreasing.' In small towns and on farms, kerosene, gasoline and wood are largely utilized for cooking. For the past four years, along any country road, it is a common occurrence to hear a buzz-saw cutting old fence posts or timbers taken from creek bottoms. Many thousands of tons of coal are displaced each year through the use of corn and cobs. In larger towns, gas plants have been installed, and many housewives use gas-in communities contiguous to natural gas, that is used for industrial and domestic purposes. The time has gone when industrial and domestic consumers or dealers are satisfied to buy anything that is black-competition among the coal-producing states is keen, and will become more so. Eastern and southern fields are turning out splendidly prepared coals of high quality, and with their lower freight rates to competitive territory, will entirely nullify the use. of our Western coal unless-

Jan 1, 1922

By F. T. Baker

The Primero mine, operated by the Colorado Fuel & Iron Company, is located 17 miles west of Trinidad, Colorado, in Las Animas County. Unusually bad roof conditions, along with heavy side pressure and other conditions causing rapid decay of timbers, all combine to create a very serious timbering problem. The height of the coal averages six feet six inches. It is a heavy coking coal and has a tendency to become easily crushed and broken down in the seam. The seam lies about 35 feet below the sandstone and the intervening formation is composed of loose shaly rock, and as the coal is extracted, the air slackens this rock to such an extent that within 24 hours, roof falls varying from five to fifteen feet in height are likely to occur. Under these conditions it is necessary to use cross bar sets in both rooms and entries, and they must be spaced no further apart than three and one-half foot centers, and be maintained within a distance of three feet of the face. Rooms are spaced on fifty footcenters, and cannot with safety be driven to exceed 14 feet in width, and 200 feet in length. The large pillar must be maintained to protect from side pressure, and the rooms must be driven up and retreated with as quickly as possible to avoid the squeeze caused by the intense side and roof pressure. Best results in extraction have been obtained by driving rooms for only a distance of 150 feet. Under these circumstances, it is readily seen that timbers of small diameters cannot be utilized in timbering any development work of a permanent nature. Entries are driven nine feet wide, and special peeled piling with an average diameter of 12 inches are most commonly used. It, is necessary to use lagging between each set of crossbars . Conditions such as these necessitated an immense expenditure for mine timber. In addition to ordinary seven and eight foot props, we used a yearly average of 65,000 feet of heavy peeled piling, averaging in diameter from 10 inches to 12 inches. Annual expenditures for timber of all classes was in excess of $60,000.00. Timber costs per ton averaged around 29 cents. In view of these exceptionally severe timber conditions at Primero, the company, in 1920, had a survey made with a view of providing some remedy to this problem. A comparison of the life of main entry timber at other bituminous mines was made, and an average life of four years was established. The actual data collected at Primero indicated an average of less than two years in the manway or "return" airways, and up to five years on the haulageways or "intake" airways. While some of this timber will stand up for a much longer period than this, a close inspection will reveal in most cases that its period of usefulness is spent. It is very essential when discussing the life of timber, especially that used on, main haulageways and aircourses, that a distinction be made between the point of service, that is, the point where it is sound, serviceable and able to carry weight, and the point of breakdown or failure, where it is no longer sound and able to carry weight. In figuring the life of timber, the point of service only should be considered as timber will frequently stand for a considerable length of time when it is entirely decayed and unserviceable. The larger part of the timber used for our permanent work was Alpine Fir, or what is locally termed Red Spruce, and the supply of this I is gradually becoming depleted and has to be obtained at a point so distant

Jan 1, 1926

PRESIDENT LITTLEJOHN: The paper of Mr. Emrick will now be open for discussion for about twenty minutes. The meeting is now open for discussion. MR. EMRICK: There is some question that may have occurred to you at different times, that is how are you going to tell when the bits are properly made? A fairly good rule to go by is when the used bits come out of the mine, if half of them are bent and half of them are broken, the average is pretty good MR. GEO. B. PRYDE (Union Pacific Coal Company): I would like to ask Mr. Emrick if he has any figures as to the saving of Dower with the different styles of its. MR. EMRICK: I suppose you mean chisel point bits and pick point bits? MR. PRYDE: Yes. MR. EMRICK: So far as I have been able to learn, the only reason why chisel point bits are used is to prevent coring that might be done by the cutter chain. The pick point bit, of course, is the proper thing to use. It can be used when the position of the cutter links in the cutter chain is right. I do not know of any figures which give power consumption ratings on the use of pick point and chisel point bits, but there are tests and ratings, etc., which have been taken- which have been tested as against different bits, which have been given proper clearances against bits not having been given proper clearances, and they will run,-in their saving in power, they will run 20 to 25 per cent. MR. A. C. WATTS (Chief Engineer, Utah Fuel Company) : I would like to ask Mr. Emrick if he has any record showing the saving in power on using the alloy steel chisel bits. I know that several experiments have been made; I do not recall the figures now, but we had a very decided saving in power. MR. EMRICK: I haven't any of the records. Do you think that is because of the steel that has been used? MR. WATTS: Well, they were all sharpened by the same man and used in the same machine, and at the same shop. I do not know the composition. It is "Red Star" Vanadium that I had in mind. MR. EMRICK: I have not seen any records. Some companies are using the tool steel bits because they stand up a little bit better. MR. BENEDICT SHUBART (Secretary) : I was going to ask Mr. Emrick about that question. There is one company that does not recommend tempering the bits. They recommend using not exactly self-hardening steel, but one that is bard enough without quenching-they use 80-90-point car- bon but about a 70-point manganese, not exactly self-hardening steel, but they do not temper this at all. Will Mr. Emrick state if a steel of that kind could be worked in the bit sharpening machine that his company makes, as it

Jan 1, 1925

forated, allowing the completion of the removal of wash water. When discharged into the washed nut bin, the coal is moist but carries so little water as to not be objectionable to the trade, nor to give any difficulty from freezing during the coldest weather. The rock and bone from the primary jigs is elevated to a 15-ton bin by means of a single strand scraper conveyor 40 feet center to center operating on a 45 degree incline, carrying 12" x 5" scrapers every two feet. This conveyor travels at a speed of 100 feet per minute and has a capacity of 17 tons per hour. From this bin, this material falls into the third or rewash jig similar in all respects to the first two, which discharges the rock waste directly into a 15-ton refuse bin below and the bone into a short dewatering conveyor which delivers into a similar 15-ton bin from which the bone is taken to the powerhouse. The oversize and water from the shaker screen, the water from the dewatering conveyor for both the washed nut and bone, and the sludge and wash water from the three jigs, are delivered by launders to the first compartment of a three-compartment settling tank. Most of the coarser broken coal is deposited in this tank, from which is it continually removed by a bucket elevator carrying 8" x 5" perforated buckets operated on a 60 degree incline at 200 feet per minute, capable of delivering 25 tons per hour to the 50-ton washed coarse slack bin. The water passes successively through the three compartments of the settling tank and from thence through a six-inch pipe to a centrifugal pump, circulating 900 gallons per minute against a 32-foot head. A four-mesh screen 30" x 72" in the third compartment of the settling tank removes the chips of wood, paper, and the other trash, which otherwise would accumulate in the water. Water is provided from the camp water system, deriving water from the well located in an arroyo bed. During the summer months just passed, the water used, has been 108 gallons per ton of raw nut, or 146 gallons per ton of washed nut. The water meter had not been installed last winter, but it is estimated that operating at capacity, the washery will be found to require only about 75 to 100 gallons per ton of raw nut. It has not been found necessary, nor advisable, to attempt to dry the sludge from the settling tank, nor to save the water from leakage of the tanks and bins. The sludge from the jigs is washed into the settling tank and the sludge from the settling tank is washed through a tile drain to the arroyo. The jigs, shaker screen, circulating pump, washed slack elevator, and the rock handling conveyor, are all driven from line shafts driven by one 40 H. P. motor, each jig driven through a clutch. The belt conveyor and the washed nut conveyor, have separate motor drives of five and seven and a half H. P. respectively. The washer is housed in a corrugated iron building, which is partially heated by steam coils. One attendant is required for operation, regulating the feed of the jigs, the supply of water, removal of the rock, and oiling and maintaining the machinery. The rewash jig is operated only intermittently. About eleven per cent by weight of raw nut is removed as waste and four per cent goes to the washed slack bin. No control analyses of the products have been made; the efficiency of the plant being determined only by the physical appearance of the products; but the washery has been a source of pride and satisfaction to all those connected with it. As mentioned before, it has caused no interruption of operation and it has assisted materially in creating an unprecedented demand for ALAMO nut. MR. CHARLES: If there are any questions, I shall be pleased to endeavor to answer them. MR. LITTLEJOHN: Mr. Charles, do I understand it is the nut only that is washed there? MR. CHARLES: Yes, sir. MR. LITTLEJOHN: What did you say the size was? MR. CHARLES: Through three inch round perforations, retained on

Jan 1, 1926

It was said that the coal operators are losing a great advantage in permitting the oil producers to take the domestic market away from them. Coal is so much less expensive and more economical than oil that even the oil producers themselves are burning coal under their stills. No longer is the housewife afraid of machinery. Not only does she operate an automobile, but in her home she is used to vacuum sweepers, washing machines, refrigerators, and multitudinous devices. She is no longer machine-shy. An electrically operated stoker, if properly introduced and guaranteed with only a fraction of the enthusiasm that the oil furnace salesman shows, would get a ready reception. Several devices now on the market are much less complicated, much less apt to get out of order, than the oil burners. In place of an increased cost for the sake of convenience, the stoker will give all this convenience at a decreased cost. So said Mr. Herres. He said, however, that it must be enclosed so that the working parts are not too much in evidence. MR. McAULIFFE: While it appears possible to adapt a continuous feed to the needs of the furnace in an apartment or a house burning thirty tons or more annually, it is not yet possible to get a furnace that would satisfy the home which burns only seven or eight tons in a season. A delegate described the Garrison stoker which is designed to care for this problem. Mr. Herres said that the Pacific Coal Company had a small stoker furnace more simple than the Harrington. Pulverized coal equipment is being adapted to use in apartment houses. The stoker designed by Lloyd Garrison, State Engineer of Utah, was described, and also one which Mr. G. W. Megeath of Omaha, Nebraska, had manufactured, which Mr. McAuliffe says, is recommended only for Rock Springs coal. It was brought out that there are over forty installations of the "Iran Fireman" in Salt Lake City. For apartment buildings, there is no question as to their satisfaction. Many of the down town office buildings are so heated.

Jan 1, 1925

By Geo. B. Pryde

Dear Sir: Yours of July 23rd, relative to my appointment on the Safety Committee in connection with the Rocky Mountain Coal Mining Institute. As you say in your letter, "The duty of this committee is to draft suggestions as to safer mining practices with the idea of preventing disasters in coal mines." Much has been written and many suggestions made on this same subject, and it is very hard to put up further recommendations than have already been made. The disasters you mention in your letter unquestionably have direct reference to coal mine explosions, which from time to time still occur in this and other countries. As far as our Western mines are concerned, you know that sprinkling and shot firing by electricity have been very extensively carried out. Notwithstanding these precautions; we have had a few rather serious disasters in the past in these mines. I do not care to place any blame or responsibility on the companies having these disasters, but it is a fact that in each and all of them, after careful investigation has been made, that the human element has had more or less bearing on the accidents happening. From most reports that we gain, either directly or indirectly, it is very evident that investigation shows after an explosion that the rules governing one or both of the above safety measures have been somewhat carelessly or negligently carried out. Much has been written and read about rock dust sprinkling, but it is questionable if this method is doing a great deal toward the eliminating of disasters. While it is true it may have the effect of preventing propagation, still I do not believe anyone claims for it a sure preventative against initial explosions. I had occasion not long ago to visit a mine, after an explosion, in which dust barriers were supposed to be hung, and from indications it was quite evident that the dust barriers had been in operation, but they did not prevent the explosion from reaching. all open parts of the mine. It is also true that profuse scattering of rock dust throughout a mine would have a beneficial effect, but there is a question arises here as to whether the sprinkling by rock dust or the spraying by water, if available, is the most effective. I am satisfied that if all coal mines are kept well sprinkled and all open workings maintained in a thorough moist condition, that the biggest factor in a coal mine explosion is in this way eliminated. There is no doubt but what the use of permissible powder, particularly if shot by electricity, has had a very marked effect on the number of dis¬asters in mines, and if this method of shooting was energetically carried out there would be a difference in the number of explosions, both minor and Major, all over the country. Some of the recent explosions have taken place where no shooting was being done, but there is no denying the fact that the other ingredient, namely, coal dust, entered in the elements very extensively. We have read and heard of hydraulic cartridges and other patents (substitutes for powder) that were being worked out for the purpose of

Jan 1, 1923

By F. C. Miller

The Colorado Fuel and Iron Company has divided their coal mines into groups or divisions: Las Animas, Huerfano, Fremont and Gunnison counties. Each division is represented by a safety committee composed of three men appointed by the management and three men selected by the employes? representatives. The three men appointed by the management are usually from a group engaged in routine work that is primarily of a safety nature. Mr. Robert McAllister, chief mine inspector; Mr. George B. Parker, superintendent of first aid and mine rescue training; Mr. F. C. Miller, chief chemist, fuel department; and Mr. 0. C. Irwin, assistant chief electrician. The three men appointed by the management act in each of the four divisions. It is the duty of the safety commit- tee to visit each mine three times per year and make a thorough investigation of conditions underground and on top. Their report is in the form of recommendations to the management for their consideration. They are also called to investigate all fatal accidents and learn, if possible, the cause leading up to the accident and recommend precautionary measures that will prevent the recurrence. This committee inspects the haulage roads, air courses, manways, electrical equipment, ventilation, timbering, working places and humidity. In addition, each mine has a local safety committee with the superintendent acting as chairman. It is the duty of this committee to keep in daily touch with conditions underground and on top. They hold weekly meetings and discuss problems related to safety. These men work on local conditions that govern their affairs. As an example: One of the mines has a checking out board at the man-trip parting in addition to the regular checking in and out system as required by law, and this board is checked before the man-trip leaves for the outside, giving the officials a chance to take prompt action in looking up a man who may have become ill or injured. Should a man walk out and forget to check off, there is a penalty imposed. The ventilation of a coal mine is most important and the method of conducting the air to the working face is one of the greatest precautionary measures linked with safety. A quantity of air must be maintained at every working face to insure rapid diffusion of explosive or noxious gases and in a manner without interruption. With this intent in, view, the Colorado Fuel and Iron Company is installing fan equipments with capacities of 200,000 cubic feet per minute with dual drives, twin fans in some instances, for insured circulation. Dual drives consist of a steam engine using exhaust

Jan 1, 1925

MR. MARGOLF: Our final speaker this afternoon before we have an opportunity for some questions for the members of the panel, is a gentleman who has spent more than 40 years in the newspaper industry. He started out as an office boy while he was still in high school. He worked his way through college working for a newspaper in Lexington, Kentucky where he graduated from the University. He has a long association with the Albuquerque Tribune but what brings him here today is in his position as editor of The Rocky Mountain News which is certainly one of our largest circulations. I think it is the largest circulation newspaper in the Rocky Mountain states. Ralph Looney, in that

Jan 1, 1982

PRESIDENT OLIVER: May I have your attention, please, gentlemen? The Forty-Fourth Meeting of the Rocky Mountain, Coal Mining Institute is now In session. I want to say just a few words of welcome to all the delegates this morning, both old and new. There is a large group of men around here I notice who come to this meeting year after year, and it occurs to me that they must be getting something worthwhile out of these meetings, the renewal of old acquaintances, the making of new acquaintances, and the opportunity to find out what is doing in the technical end of the coal business, and what is new. So, we greet you enthusiastically and trust that you will find this meetnig on a par with all those which have gone before and. that each one of you will leave these sessions determined that you will not miss next year but will be back again. So, with that introduction, we will proceed with the business of the convention. As time is fleeing away from us, if there is no objection, I wil lentertain a motion to dispense with the reading of last year's minutes. Will somebody make that motion? MR. H: C. MARCHANT: I move we dispense with the reading of last year's minutes. (The motion was carries unanimously.)

Jan 1, 1948

By D. Harrington

E. H. DENNY (United States Bureau of Mines, Denver, Colorado) In the absence of Mr. Harrington it is my privilege to read his paper, which is in his usual, forcible and sincere style, and it is within the province of this Institute, certainly, to go into it as it concerns safety and efficiency in mining. He brings out some points in his paper that, I think, are well worth the consideration of the Institute. The figures he uses were compiled by Mr. Adams, of the Bureau, and cover a five-year period. However, examination of similar Bureau figures for a ten-year period, or any other long period on other bases brings out similar results. The figures in this paper have been based on the million hours of exposure of accidents, and the figures based on three hundred working-man-day basis, or on tonnage, brings out similar results. This paper is entitled "Accident Record in Western Mines," and it is, in a way, an amplification of Mr. Harrington's letter which was read at the Glenwood Springs Meeting.

Jan 1, 1927

By N. H. Wetzel

Railroads, attempting to increase their tonnage without adding new lines, have for some time realized there is a definite relationship between increasd haulage efficiency, and constant communication with each moving unit that operates along their roadbeds. Elaborate radio communication equipment has been devised for this purpose, and is rapidly being installed. Coal mines are faced with similar haulage problems and have sought this constant contact through the use of telephone systems, and dispatcher stations. Often the fixed mine telephone system is unsatisfactory, since the desired person is not present at the phone when needed. Dispatchers lose contact with a motorman as soon as he is out of sight, until he calls in from another telephone. The recently developed frequency-modelated radio phone which makes use of the trolleywire network in a mine as a carrying medium, permits instant and continuous contact between dispatcher and locomotives. The motorman can immediately contact another motor or the dispatcher regardless, of his motor's position on the trollywire system, whether moving or standing.

Jan 1, 1948

MR. HARRINGTON: I would like to ask Mr. Bottomley if they fire their shots while the men are in the mine? MR. BOTTOMLEY: No sir; the shot-firing law in our State requires the shots to be fired after the men are out of the mine. We fire more shots than we did under the hand method of loading. Where formerly four holes were drilled, now we drill eight, using the same amount of powder as we did formerly, perhaps a little more, but we use a slower grade of powder. CHAIRMAN LITTLEJOHN: Any further discussion, gentlemen? MR. GIBSON: Mr. Chairman, I would like to ask Mr. Bottomley, if, in his shot-firing system, as I understand it, he has a very high coal and is working something like eleven feet? MR. BOTTOMLEY: Something like that. MR. GIBSON: I read the article that you referred to. Did you use both the first and the second delay explo¬ders in shooting the coal? MR. BOTTOMLEY: We use the ordinary fuse. MR. GIBSON: That is what I wanted to find out; whether you use the delay exploders and the detonators. In Utah, we are getting away from the fuse altogether, because we do not think it is accomplishing anything to use the electric light on the cap, and' at the same time shooting with fuse. We are defeating the object we might gain in using the electric safety lamp. That is a point that might be discussed a little further. MR. E. H. JOHNSON, The Coloder Company: I would like-since it is a general opinion that mechanical loading breaks up the coal, to ask Mr. Bottomley, if he finds a larger percentage of small coal, or how much, through the use of the mechanical loaders? MR. BOTTOMLEY: We do not find any great difference. In fact, we have succeeded in improving our lump coal percentage, and that is important, because it is largely domestic. At first, when the machines were installed, the boys shot the coal too hard, and we fell down a little, about two or three per cent, the first month, in our lump percentage, and we tightened up a little and changed our methods in shooting and got on to the stunt of drilling more holes and getting a slower grade of powder. We could not load as much coal in one day as we could before, but we did succeed in in. creasing our lump coal percentage four and a half per cent over the hand method, and that is quite a factor-quite an important factor and since our domestic trade is over with, we loosened up on the shooting and we are running about the same as we did with the hand loading, maybe a half per cent more, or one per cent, but pretty much the same. MR. SHUBART: Your coal is very high? MR. BOTTOMLEY: Yes. MR. SHUBART: Have you tried sunbbing the coal before shooting? MR. BOTTOMLEY: No, we have not tried that. It is very hard coal to shoot; we have no defined cleavage in our coal. It is the worst coal I ever saw to shoot. We do not try to snub it. Formerly, as I said, the miners drilled four holes, pretty well up near the top, and then four holes down, within about three feet of the bottom. It is the same thing as a snub shot, and that we find is the best method for shooting the coal. We have not tried any mechanical device for snubbing as yet. SECRETARY SHUBART: At one mine I saw snubbing tried with a Jeffrey undercutter with a seven-foot Jeffrey bar. This mine, by the way, is very similar to Mr. Bottomley's condition. They have very high coal, so the snub cut is a small percentage. They cut a seven foot undercut and raise the machine on an eight inch tie and undercut five feet to give the effect of a snub cut, 14 inches at the front of the cut, and then six inches at the back of the cut. They made a very marked increase in lump. (The bug dust would be a small percentage of the total coal), and they increased the percentage of the slack at the same time. They found a decrease by reason of the easier shooting of about 15 per cent in their slack. In other words their nut and lump coal ran considerably higher and their slack decreased 5 per cent with the snubbing cut. Mr. Bottomley, I believe, understands those conditions.

Jan 1, 1926

MR. DICKINSON: There is an increase of dust in machine loading, especially with the McKinlay loading and cutting machine which was extremely dusty. MR. FORRESTER: Declared more dust must be expected because when loading by machinery, the coal is shot harder in order to make it easier for the machine to pick it up. He believes however, that there was less hazard because of the closer supervision possible by reason of the concentration of operation. MR. McAULIFFE: Machine loading more dusty than hand loading. D. HARRINGTON: The hazard is greatly increased by modern methods of loading. Not only do the methods increase the quantity of dust, but they also increase the rapidity of mining and the increased quantity of coal broken down causes large quantities of gas to be released. The number of motors on loading machines and conveyors add to the hazard. No more dangerous places can be found for such motors than at the working face where there is excessive quantities of pure coal dust and where there is more gas than along any other point. Regarding Mr. Herres remarks that the machine loading was safer on account of the concentration and possibility of close supervision, Mr. Harrington said he believed concentration likely to prove a source of danger rather than its preventive. At Dolomite, Alabama, a number of men had assembled, and as a result what was a relatively small explosion killed a large number of men. Concentration is not without its dangers to mine operations. MR. McAULIFFE: These arguments do not appeal to me. Few places are better sprinkled than the working places in a machine loading mine. There is. more effective supervision, and there can be more ventilation. I believe machine loading will increase safety by that very concentration that Mr. Harrington deplores.

Jan 1, 1925

CHAIR: I see a great many safety men in the audience and I hope you will all take part in using up the time that we have left. The point brought up by all was the necessity of education. It is very hard to know just how this is going to be done. We get very little encouragement to do this. At a recent meeting at Rock Springs, 100 in attendance, and most of them mine officials. Another condition which contributes to accidents is the labor turnover in many of our States. With many companies I am told from actual statistics the labor turnover is 125 per cent. Each field has different mining conditions so that men coming from one field are not always familiar with the mine conditions in the field they come to. These are conditions which have to be overcome. WM. LITTLEJOHN: Mr. Harrington brought up the subject of sprinkling. I will try to tell what we are doing at the Utah Fuel Company camps. Our dust at Castle Gate is the most inflammable gas that has yet been tested at the Pittsburgh station of the Bureau of Mines, so it is up to us to use every precaution to keep it down. I will try to tell what we are doing regarding sprinkling from tanks. We now have in operation two tanks in our locomotive roads, one in Castle Gate, one in Sunnyside. These tanks are something like 500-gallon tanks with pump on one end of truck which gets its power from the power wire and has a half circle perforated pipe on the other end of tank. This is simply hooked on to the locomotive. When the pump is started up it throws a fine spray of water all around which wets the roof, the sides and floor. We found this very successful from an economical as well as a working standpoint. A roadway that we probably would have had to pay a man at least two shifts for, covering the full distance, with the ordinary hose and spray, we can do in half a day and do it more thoroughly. We are also figuring on at the present time using the same system on rope haulage ways, which of course will have to be run by a reel from the feed lines, handling say four hundred feet each way before reconnecting. We haven't got it finished, but are working on it at the present time. MR. COLBURN: I would like to say a few words -about this question of education. Education was mentioned by all three sections of the Safety Committee. Education regarding safety might be divided into two branches. One branch is for the official at the mine to keep him acquainted with the latest developments in safety equipment and safety methods. The other part of education is for the workmen. The United States Bureau of Mines is co-operating in both directions. Safety Clubs are organized around the Bureau of Mines First Aid Training, but it is the idea to expand those clubs and teach the miner the advantage of such-things as the closed safety lamp, and also the regulations that have been made for his safety. In Illinois we can't operate with the closed lamp, because the miners in that section of the country are not educated to the advantages of the safety lamp. Another form of education has been taken up by the National Safety Council, consisting of voluntary organizations similar to the Institute, to which all mining men are invited to attend. Such conferences nave been held in the Lake Superior district, in Butte, and in Globe, Arizona, this year. These are to be extended throughout the coal mining regions. CHAIRMAN PRYDE: The Union Pacific Coal Company has also built two tank cars of 600 gallons capacity each. The tanks are connected with hose, so that water can flow from one tank to the other. A centrifugal pump is mounted on a truck, and connected to the front tank. This pump takes its power from the trolley wire. The discharge from the pump is perforated, so that it sprays the floor and sides of the entries. We expect to use this water train on main haulage ways where we have no sprinkling line.

Jan 1, 1923