Search Documents

By W. Jilowa, C. Nguni, M. Simukoko, C. Nampungwe

The upsurge in cobalt price and demand is propelled by high demand from the electronics and electric vehicle industry. Konkola Copper Mines has cobalt occurring with copper in the ratio 1:10 in ore. The ore is treated in the concentrator and recovered at the smelter as an alloy (Cu 70%, Co 4%–7%, 15% Fe). Subsequent processing of the cobalt alloy is challenging, with very few plants able to treat it, leading to marketing challenges. Konkola Copper Mines sought to improve the cobalt alloy by producing a slag that is easier to handle and process in subsequent processes. Cobalt alloy (3.60% Co, 85.4% Cu) was re-melted in a copper bath four times the mass of the alloy. Silica and lime were added for phase separation and fire refining commenced. Following completion of fire refining and after holding the temperature at 1200°C, cobalt-rich slag was skimmed and blister copper was cast into anodes for electrorefining

Jan 1, 2023

By A. McQuillan, N. Bar

Geotechnical models developed during the planning stages of open pit mines are three-dimensional so as to capture the spatial variation in lithological, structural, hydrogeological, and geomechanical conditions. Geological models that describe the lithological and structural (faulting and folding) characteristics of a deposit are always 3D. Likewise, boreholes and piezometers used to develop geomechanical properties and groundwater models are drilled at spatial offsets across the deposit to understand the lateral and vertical characteristics. Yet when geotechnical analysis is completed, often the three-dimensional geological, hydrogeological, and structural models as well as geometrically complex 3D mine designs for optimizing economic mineral recovery and overburden removal are simplified to two-dimensional sections. In this paper we demonstrate that this simplification can lead to the wrong failure mechanism being identified, analysed, and/or a conservative factor of safety being calculated and hence an over-estimation of slope stability. Through case studies we show how three-dimensional analysis methods are more suited to rock slopes, particularly those with anisotropic material strength, when singularities such as geological faults are present, and nonlinear slope geometry. When the same slopes are analysed in two dimensions, the failure mechanism calculated is often fundamentally incorrect. The case studies further reveal that the factor of safety calculated in three dimensions is not always higher than the two-dimensional factor of safety.

Feb 6, 2023

By M. Mbonami, R. Pretorius, J. Miller, P. Kyony, B. Nel, N. Mautsa

Challenges due to the formation of stable froth in acid leach systems is common at many copper and Ccbalt producers. Stable froth affects downstream process, critical equipment, and operational parameters. In severe cases the froth present safety and environmental risks and increased operational costs. Solids reports in the pregnant leach solution, accumulates, and clogs launders resulting in a potential costly safety and environmental risk. Solvent extraction is operationally affected by crud formation, organic solvent and extractant losses, reduced mass transfer due to the solids carried downstream. This article reviews the generally inadequate mechanical and hydraulic solutions of froth elimination employed over the years. The recent introduction of a chemically based solution able to eliminate froth problems that can potentially turn around the situation for those who adopt the technology.

Jan 1, 2023

By Y. Yang, M. Zhang, X. Xia, S Shi, Z. Shen

A stepwise arrangement of flotation cells is the most common layout of a flotation circuit in the mineral processing industry. In such a design, slurry flows from upstream to downstream by means of gravity, and the middling products are returned to previous stages by pumps. This paper will introduce an alternative solution in which the forced-air and slurry-induced flotation cells are adopted so that all the flotation cells can be placed on the same horizontal platform and no pumps will be needed for middling product transferring. The technology of the forced-air and slurry-induced flotation cell will be described in detail, including unique features, the working principle and the related fundamental problems. The comparison of capital investment, operating cost and metallurgical performance will be made between the conventional stepwise arrangement and the samelevel arrangement technology based on industrial practice. Keywords: Forced-air and slurry-induced flotation cell, same-level arrangement, stepwise

Jan 1, 2020

By J. Maritz, K. de Beer, S. M. Buthelezi

The economic upheaval of COVID-19 forced companies to invest in emerging technologies to aid recovery. One such technology is extended reality, which is becoming a mature and innovative tool. Early adopters are seeing significant benefits in learning, training, immersive data visualization, and remote assistance. In South Africa, the mining industry is increasingly interested in using extended reality to optimize and innovate operations. The Minerals Council of South Africa's July 2021 report highlighted the potential of extended reality's to achieve zero-harm production and modernize the industry. However, the extent of extended reality adoption in mining remains unclear due to limited information on its usage. This study addressed this gap by distributing an online survey to assess awareness, knowledge, and current uses of extended reality in South Africa’s mining sector. The results indicated that virtual and augmented reality had the highest levels of awareness and usage, primarily for learning and training. Mixed reality, however, had the lowest awareness and knowledge levels. In terms of applications, visualization and remote assistance had the least use cases. These findings highlight that the South African mining industry is deficient in its understanding and use of extended reality technologies. Without better awareness and application, the South African industry risks missing out on the full benefits of extended reality. The study underlines the need for the South African mining industry to improve its outlook on extended reality technologies to fully leverage their potential applications and benefits.

Jul 10, 2024

By P. Fu, Y. Ma

Residual collectors and their byproducts (e.g., CS2) in flotation effluents can cause water contamination and even result in serious health hazards to humans and animals, Therefore, residual flotation reagents should be removed properly before discharge or recirculation into flotation circuits. In this work, four thiol collectors (potassium ethyl xanthate (EX), sodium diethyl dithiocarbamate (SN- 9), O-isopropyl-N-ethyl thionocarbamate (Z-200), dianilino dithiophoshoric acid (DDA)) were chosen as model pollutants. The collector removal, mineralisation and byproduct formation were compared by sole O3 and O3/UV185+254nm. The degradation rate constants of thiol collectors by O3/UV185+254nm were 2~6 times higher than those by sole O3. The mineralisation of collectors was also remarkably enhanced by O3/UV185+254nm. The degradation efficiency by O3/UV185+254nm had the order: EX>SN-9>>Z- 200>DDA. The Z-200 and DDA were refractory flotation reagents. The degradation of thiol collectors caused the reduction of solution pH and the increase of ORP and conductivity. However, the O3/UV185+254nm achieved more evident changes of these parameters than sole O3. During the degradation of thiol collectors, less than 4% of total sulfur in collectors was emitted into air as CS2 and H2S. Compared to sole O3, the O3/UV185+254nm had additionally included UV185+254nm photolysis and O3/UV254nm, resulting in higher efficiency in removing collectors. The O3/UV185+254nm was an effective process in treating mineral flotation wastewaters containing organic reagents. Keywords: Thiol collectors; flotation effluents; ozone; vacuum-UV; degradation, mineralisation

Jan 1, 2020

By T. J. Otto, I. D. Ungerer, G. C. Lindeque, T. J. van Heerden

Anglo American Kumba Iron Ore (Kumba) continues to implement technologies focussed on improving safety and productivity; this forms part of the groups FutureSmart Mining initiative. The paper provides insights into the implementation of three technology solutions that improves the productivity of heavy mining equipment (HME). Enhancements to the short term mine planning (STMP) process, the effective use of a fleet management system (FMS) and the deployment of drones or Remotely Piloted Aircraft Systems (RPAS) are discussed. The implementation of these and other technologies contributed to a 13% and 22% increase in the overall equipment efficiency (OEE) of the primary HME at Kumba’s Sishen and Kolomela mines respectively. Four key success factors (KSF) are highlighted namely that Kumba’s technology implementation drive is a key enabler to the company’s strategy, has a strong focus on value-add, is underpinned by a holistic and integrated implementation approach and is people-centric.

Sep 1, 2021

By O. Barron, C. Felix

In 2023, polymer electrolyte membrane fuel cell membrane electrode assemblies accounted for about 62% of the global fuel cell market share and this demand is expected to grow. Commercialisation requires technologies capable of cost-effective, high-volume manufacturing. The membrane electrode assembly is crucial and represents a significant cost to polymer electrolyte membrane fuel cell manufacturing. Manufacturing the electrode components for membrane electrode assemblies at high volumes can reduce production costs while delivering on the forecasted industry demands. Roll-to-roll is a mature coating technology applied in various manufacturing industries such as batteries, printed electronics, microelectronics, photovoltaics, printing, paper consumables, etc., with significant potential for polymer electrolyte membrane fuel cell manufacturing. While the high-volume production process for membrane electrode assembly manufacturing differs from laboratory-scale, the membrane electrode assembly structure remains unchanged. Roll-to-roll is a continuous coating process with speeds of 10 m/min being achieved. In this work, MicrogravureTM and slot-die coating methods have been adopted and have shown promising outcomes for producing gas diffusion electrodes for membrane electrode assemblies. An overview of the MicrogravureTM and slotdie coating methodologies is provided, and a discussion on preliminary results and challenges are presented. Work on MicrogravureTM gas diffusion electrode manufacturing has already achieved comparable performance with spray-coated gas diffusion electrodes. The influence of coating parameters and drying on the coated catalyst layer quality is discussed.

May 27, 2025

By H. P. Kritzinger, T. C. Kingsley

Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications. This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron-ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates.

Jan 1, 2014

By J. L. Broadhurst, S. Rumjeet, S. T. L Harrison, T. Chimbganda

Post-mining land use for the production of industrial crops has the potential to mitigate environmental and socio-economic impacts of mine closure and stimulate post-mining economic growth. Fibre-rich plants are of particular interest due to their multi-product potential. In the South African context, where there are many abandoned and end-of-life mines near human settlements, an opportunity presents to assess the feasibility of transforming post-mining land into productive land and building resilient communities through the development of multi-product value chains from fibre-rich plants such as kenaf, hemp or bamboo. This paper provides an overview of the plant selection criteria, phytoremediation potential and the downstream options for the recovery of products and value from bast fibre plants (hemp and kenaf) and bamboo. Based on findings from a comprehensive review of the published literature, as well as interviews with relevant experts within South Africa, it appears that bast fibre plants are the best downstream option for producing ‘green’ textiles and high-end niche products, whereas bamboo is more suitable as a replacement for conventional timber. Although fibre plants have the potential to extract metals from soils, high concentrations may inhibit plant growth and affect the quality of the final fibre product. Further site-specific studies would thus be required to select the best route for both land remediation and optimal product recovery. Keywords: Bioremediation, bamboo, kenaf, hemp, multi-product value chains, sustainable postmining land use

Jan 1, 2020

By A M. Garforth

Insurers are hesitant to provide coverage for Open cast Pit side wall collapse, and even the consequent damage to plant and equipment in the pit as well as the resulting interference with the mining operations. After a general introduction to relevant principles of insurance, this paper addresses some of the major reasons for that reluctance based upon the authors? extensive claims experience, examines what limited coverage can still be obtained and looks to the future possibilities. Confidentiality of sources and examples referred to in this presentation is a natural imperative so that a bibliography is not provided but reference is made to relevant sample insurance policy wordings.

Jan 1, 2006

By B. A. Obadele, R. Machaka, M. L. Raganya, M. E. Makhatha, N. A. Moshokoa

The influence of solution treatment on the phase evolution and tensile properties of Ti-Mo alloys was investigated to assess their potential use in biomedical applications. Phase formation and microstructural evolution were studied using X-ray diffraction (XRD), optical microscopy (OM), scanning electron microscopy (SEM), and electron backscatter diffraction (EBSD). The mechanical properties were characterized by means of tensile tests and bending strength. XRD analysis showed that solution treatment increased the volume fraction of β phase and supressed the α" phase. The microstructures of the as-cast alloys consisted of β equiaxed grains with sub-grain structures of different sizes, while the solution treated alloys comprised β equiaxed grains only except for Ti- 10.02Mo, which comprised needle-like α" structures. EBSD showed an increase in the volume fraction of the ω and α" phases in all the alloys after solution treatment. The elastic modulus and UTS of all the alloy significantly decreased after solution treatment, except for Ti-15.05Mo,whereas the elongation significantly increased. The fracture surfaces of all the alloys after solution treatment indicated more ductile behaviour than brittle

Jun 10, 2024

By M. Louarrat, G. Enaime, A. Yaacoubi, A. Baçaoui, J. Blin

"The purpose of this study is to prepare a new activated carbon from olive stones for use in gold recovery by carbon-in-leach (CIL) and carbon-inpulp (CIP). The preparation method chosen was physical activation using steam. The effect of four process parameters: the residence time for carbonization, the activation temperature, the residence time for activation, and steam flow, were studied by the mean of response surface method (RSM) in order to optimize the yield, iodine index, and attrition characteristics. These two last responses were used as primary indicators of gold recovery capacity and mechanical strength. The results obtained show that optimal activated carbon can be prepared under the following conditions: a carbonization time of 157 minutes, activation at 921°C for 53 minutes, and a water vapour flow of 0.18 mL/min. This optimum carbon has an iodine value greater than 1100 mg/g and an attrition index in the order of 0.74%. These values reflect the quality of the precursor (olive stones) as a raw material for the development of an effective new activated carbon for the gold mining industry. IntroductionActivated carbon is an effective adsorbent widely used in industry due to its high surface area, well-developed reproducible microporous structure, and high degree of surface reactivity and adsorption capacity. World consumption of activated carbon is steadily increasing. It is primarily used in industrial wastewater and gas treatment and also for silver and gold recovery from cyanide solutions (Syna and Valix, 2003; Soleimani and Kaghazchi, 2008; Buah and Williams, 2010; Eddy et al., 2011). However, activated carbon is expensive and it needs to be regenerated after each adsorption cycle. In order to decrease the cost of manufacturing activated carbon, low-cost forest and agricultural wastes are considered promising new materials. In recent years considerable research has been reported on activated carbon from agricultural wastes, such as olive stones (Yavu et al., 2010), acorn shells (Sahin and Saka, 2013), peanut shells (Wu, Guo, and Fu, 2013), grape seeds (Jimenez-Cordero, 2014), coconut shells (Yalcin and Arol, 2002; Gratuito, 2008), palm shells (Sumathi, 2009), cherry stones (Jaramilloa, Gomez-Serrano, and A´lvareza, 2009), macadamia nut shells (Eddy, 2011), apricot stones (Soleimani and Kaghazchi, 2008), and bagass (Syna and Valix, 2003)."

Mar 1, 2019

By S. Dessureault

Computer Integrated Mining (CIMG) is a process of using computer networks to transform islands of enabling technologies into a highly interconnected mining system. CIMG involves the integration of advanced technologies at various levels in the mine business to achieve higher flexibility, better quality of processes and control, and improved profitability. Justifying the benefits of CIMG are difficult as many of the advantages are derived from improved flexibility, quality, and control. Justification is based on the evaluation of the benefits to be gained, compared to the required capital investment. Management tools used in mining are currently inadequate in assessing the value of advanced technology whose benefits are primarily qualitative. A key aspect of successful implementation is management acceptance, which has to be won through the capability to justify the technology's financial costs and the true value of all of its benefits. The manufacturing industry faced similar justification difficulties when adopting advanced technology in factories. A significant amount of funding and research was invested into developing management strategies and approaches to justification. Many of the problems that faced the transformation of the manufacturing industry in the late eighties and early nineties are now facing mining. The solutions derived for manufacturing may help mining in its transition to an increased reliance on integration technology. Reviewing the industrial history of computer integrated manufacturing identifies several tools and strategic frameworks that can be adapted for mining. Keywords: Computer integrated mining, justification techniques, CIM, information technology.

Jan 1, 2003

By C. Birch, J. Perold

"Due to the challenging geological environment of the Postmasburg Manganese Field (PMF), a study was conducted to determine if any benefits would derive from the inclusion of resistivity data during threedimensional (3D) modelling of the manganese resource. This was achieved by estimating manganese resources from 2011/2012 drilling data and comparing them with manganese resources estimated from the same drilling data and resistivity data collected during 2013 and 2017.Both models were adjusted to limit their extent to the same 3D modelling space. Significant volume and tonnage differences were observed for all lithological units. The greatest differences were noted in the manganiferous zones of alteration – 7.200 Mt for the geological model versus 3.700 Mt for the geoelectric model.This study showed that the inclusion of resistivity data can reduce exploration costs significantly, as a direct consequence of the resistivity data allowing more accurate siting of boreholes. This decreases the number of boreholes, samples, and analyses required due to the 3D electrical delineation of mineralized areas prior to drilling.An additional benefit is the ability to more correctly forecast the net present value of an operation due to more accurate estimation of manganese resources and stripping ratios. This is clearly demonstrated by the estimated gross profit estimation of R409 million for the geological resource model versus R264 million for the geoelectric resource model.The addition of resistivity data can, therefore, reduce exploration costs and can increase confidence in geological and financial modelling. It would be reasonable to conclude that this approach could also be used for karsthosted massive sulphide deposits. IntroductionAccording to Corathers (2014) and Gajigo, Mutambatsere. and Adjei (2011), South Africa holds between 75–80% of global manganese reserves, followed by Ukraine (10%), Australia (3%), India (3%), and Gabon (2%). The known, land-based, manganese resources located elsewhere are estimated at 2%.The majority of economically important sedimentary manganese ore deposits in South Africa are situated in the Northern Cape Province (Gutzmer, 1996). Manganese ores of the Postmasburg Manganese Field (PMF) were discovered in 1922, and the Kalahari Manganese Field (KMF) in 1940. According to Astrup and Tsikos (1998) and Gutzmer (1996), mining of manganese ore from the PMF ceased during 1989 in favour of the superior quality of manganese ore from the KMF."

Mar 1, 2019

By S. Chai

Waste dumps are widely used to discharge stripped mine wastes in open pit mining methods. As mining progresses, the height of the waste dumps will increase gradually, which may induce sliding failure once the height exceeds a critical value. Therefore, estimation of the maximum dumping height is crucial to the life-cycle use of a waste dump. However, published information about the maximum height of mine waste dumps are extremely rare. In this study, the maximum dumping height is estimated based on the strength-reduction technique by numerical simulations. The influences of dump geometry and properties on the maximum height are investigated. The results show that the maximum dump height decreases as the dump slope inclination angle α or the unit weight of dump materials γ increases, but decreases when the shear parameters of dump materials (cohesion c and internal friction angle ϕ) increase. The maximum height starts to increase with the ground inclination β when shear failure occurs at the interface between the dump and the base. Furthermore the effects of the dump width B, Young’s modulus E, and Poisson’s ratio μ of dump materials on the maximum height are almost insignificant. Good agreement was found between numerical results available in the literature and those obtained in this study.

Oct 1, 2022

By K. A. du Preez, P. J. van Staden, M. van Rooyen

Mine-impacted water, including acid mine drainage (AMD), is a global problem. While precipitation of dissolved metals and neutralization of acidity from mine-impacted water is accomplished relatively easily with lime addition, removal of sulphate to permissible discharge limits is challenging. This paper presents a high-level comparison of four sulphate removal technologies, namely reverse osmosis, ettringite precipitation, barium carbonate addition, and biological sulphate reduction. Primarily operating costs, based on reagent and utility consumptions, are compared. Each process is shown to be subject to a unique set of constraints which might favour one over another for a specific combination of location and AMD composition. Access to and cost of reagents would be a key cost component to any of the processes studied. The total cost calculated for each process also depends on the type of effluents that are allowed to be discharged.

Oct 1, 2021

By A. Çelik

Wheel loaders are widely used in many sectors due to their mobility, operational flexibility, and low costs. The literature is mainly focused on improving the hydraulic, mechanical, and electronic subsystems of these machines in terms of efficiency or developing strategies for controlling these systems. In this study, the effects of the loader operator and different working conditions on the loading performance were investigated. The study was carried out at the Can Lignite Enterprise (CLI), which is a major coal producer in Turkey. In the study, which lasted approximately four months, a total of 808 measurements were performed to investigate seven different scenarios. The effect of a single parameter on loading performance was investigated in the first six scenarios. The results showed that the biggest impact on loading performance was caused by the operator's experience with 63.4%. On the other hand, the worst and most ideal working conditions determined from the first six scenarios were tested in the seventh scenario. It was tested as a script. The test results showed that the loading performance was 285.5% more effective under the most ideal operating conditions compared to the worst operating conditions. In addition, in the study, the loading performances of five loaders with four different capacities were examined in terms of energy efficiency and it was determined that the Kawasaki 115 work machine, which has a higher model and lower engine operating hours, was more advantageous. In the study, various suggestions were developed in parallel with the research results. The most prominent and easiest to implement of these suggestions is related to the selection of the loader operator.

Nov 27, 2024

By S. Plaatjie, L. Linzer, M. S. D. Manzi, M. Sihoyiya

Fiber-Optic Sensing and UAV-Platform Techniques for Innovative Mineral Exploration (FUTURE) is a joint European Union and South African consortium project funded under ERA-NET Cofund ERA-MIN3. The project aims to develop cost-effective and novel seismic methods to image geological structures ahead of the mine face, ultimately leading to improved decision-making and safer mining practices. In this study we present results from numerical simulations conducted at South Deep Gold Mine for active in-mine seismic surveys. The study uses a finite differencing code known as WAVE3D, which models models the propagation of a seismic wave generated by stress pertubations that are applied to a defined grid. The numerical simulation model included two major ore bodies (Black Reef and Ventersdorp Contact Reef) and mine tunnels. The model was constrained using laboratory physical property measurements from underground borehole samples such as seismic velocities (e.g., compressional and shear waves) and bulk densities. Two case studies were created, one modelled the active shots and receivers on surface, and the other modelled the shots at depth (in a mine tunnel at ~4000 m depth) with receivers on surface. In both cases, the objective was to investigate the wavefield propagation through the rockmass between the mine tunnel and surface. The simulated wavefield produced by the source located along the mine tunnel was successfully recorded on surface. The surface-recorded wavefield exhibits clear one-way P-wave arrival times at approximately 450 ms to 500 ms, which can be used to calculate the surface-tunnel P-wave refraction tomogram. The results from the study were used to constrain the design, and for the acquisition and processing of the real surface and in-mine seismic surveys acquired under the FUTURE project.

Jan 12, 2025

By J. H. Zietsman, M. W. Erwee, Q. G. Reynolds

Pyrometallurgical furnaces, essential for metal extraction, operate at temperatures exceeding 1600°C and represent complex multiphase systems that challenge direct industrial research. Multiphysics models play a key role in shedding light on their intricate behaviours, supporting the refinement of design and operational strategies. Integral to the operation are the tap-holes, which facilitate the removal of molten products and are routinely opened by lancing, a process comparable to the use of a cutting torch, where high temperatures result from oxygen reacting with an iron lance. When the lance pierces the clay, oxygen gas enters the furnace, which could influence the behaviour of the molten material inside. In this work, a multiphase fluid flow model was used to investigate bulk flow dynamics, with a focus on the effects of the lancing process on the inside of the furnace, immediately behind the tap-hole. Incompressible and compressible multiphase fluid solvers were used and compared with respect their performance – the intention was to assess whether using a compressible solver would yield a different solution to the incompressible one. It was concluded that there are negligible disparities in bulk fluid flow behaviour between the solvers for the case studies examined, indicating that solver selection might be less consequential for certain aspects of oxygen lancing.

Apr 16, 2024