Search Documents

By J. Kitagawa

The principal objectives of a metallurgical test programme for a 'grass roots' mining project are twofold. The first requirement is to establish the metallurgical viability of the project by demonstrating that acceptable results can be obtained by processing of the ore. The second goal is to obtain essential supporting data to determine whether the project is economically feasible. This involves several functions, which include the establishment of a workable flowsheet, the obtaining of design criteria for the commercial plant, and the collection of the evidence necessary to convince management, and often a third-party expert, that the metallurgy predicted for the ore can be achieved in a full-scale operation. The latter task is facilitated if a coherent overall picture is presented considering the geology of the orebody, the mining plan, and the mineralogy and metallurgy of the ore. The purpose of this paper is to provide guidance in the establishment of a test programme to meet the above objectives.

Jan 1, 1978

By K. Moxham, B. McKeown

The South African gold and platinum deposits were formed in very different ways and yet both have many similarities. They are flat dipping tabular orebodies, extremely narrow and located in hard abrasive country rock. The mining methods employed are also similar. Primary access is via shafts or declines; secondary access is via haulages and cross-cuts; and tertiary access is from raises. The proposed solution for rapid access described in this paper is focused on the haulages and cross-cuts.

Jan 1, 2006

Orebody modelling and reserve estimation are now subject to sophisticated procedures, but folded stratiform and stratabound deposits present particular problems in transforming coordinates of samples and blocks into their correct relative positions prior to deformation. In this paper an approach is taken whereby a geologically interpreted reference plane is used as a control. The study area is the Rio Tinto Minera copper mine near Santiago de Compostela, Spain. The transformation procedure on the 'unfolded' state is described, its limitations assessed and advantages considered.

Jan 1, 1987

By L. Capponi

At Tapira Mine (Tapira/MG/ Brazil), the largest phosphate concentrate producer in Brazil, the mining is fully mechanized and carried out using open pit mining. This work presents a review of the sampling protocol used for short term mine planning at different stages. Sampling is carried out in two steps. Firstly, diamond drill cores are sampled at 50 x50 x5 metre pattern. Fosfertil analyses grades of P2O5, Fe2O3, CaO, MgO, SiO2 and TiO2 plus geological logging. This information feeds the long term block model. Secondly, drill cuttings are collected at the mining faces released for blasting. The drilling pattern is staggered and when blasting is not necessary, a drill hole is made centered in the block area (25 x 25 x 5 m). The primary samples have mass approximately 60 kg and the same chemical parameters are analysed. Metallurgical and mass recovery tests are performed as well. These samples are used to build the short term block model. At the final stage, the short term mine planning model is used to build a stockpile blending model which is simulated using a spreadsheet to match the goals established by the process plant.

Jan 1, 2009

By J. E. Forbes, B. K. Loveday

The role of gravity concentration in the recovery of gold from typical South African gold ores is described. The location of the concentrator in the grinding circuit is discussed, and typical capacities and operating costs are given. Some operating problems are mentioned, but the performance of concentrating equipment is not dealt with in detail since this to some extent depends on the nature of the ore. It is concluded that the main benefits are an improved recovery of coarse gold and a reduction in soluble loss. The use of a long leaching time and a carbon-in-pulp recovery system may eliminate the need for gravity concentration. but gravity concentration is seen as an inexpensive way of improving the recovery on existing plants.

Jan 1, 1982

By S. M. Rupprecht

The transportation of men, material and rock in mechanization programmes is often neglected, or at least plays only a secondary function, as the primary focus is on proving the technology. This is despite recognition of the fact that mechanization is essential if gold mines are to remain competitive. However, the use of totally mechanized systems will require further research in the short to medium term before they become generally available. Thus, there is a real need to improve mechanized men, material and rock transportation systems as they are currently used. This applies to both reef horizons as well as to horizontal transport systems. Keywords: Transportation, rock handling, material handling, men transportation, face cleaning, gully cleaning, continuous scraper, monorail, mechanized raise climber, mechanization.

Sep 1, 2001

By W. Peters, W. A. H. Poppmeier

An overview is given of the present state of traditional and new steelmaking equipment and techniques, and one of the direct steelmaking methods that are currently being developed is described. In steelmaking processes, coal is used to supplement the energy input and to reduce iron oxides in the slag. Foamy slag practice is discussed, and the most widely used types of ladle recarburizers, their properties, and manufacture are described. It is concluded that the use of carbon sources, mainly for supplementing energy and as reductants, will increase in the future, but that demands on the purity of the materials will probably become more stringent. If hydrogen were manufactured at a competitive cost, it could become an alternative fuel and reductant in the field of iron and steelmaking.

Jan 1, 1993

By M. H. Lampen

The SILAG Material Tracking System MTS monitors and controls the complete material flow throughout the plant - and even companywide. The customized system developed by Siemens especially for bulk material handling applications enables companies to track bulk material from the mine to the harbor, to the steel mill or to the power plant. All relevant material data is available at every single step of the material’s journey. SILAG is an open, scalable system based on Windows NT / 2000. Using standard interfaces of Windows NT, like API, ODBC, SQL and socket technology, the system is very flexible and can easily be tailored to meet different requirements. SILAG can be used as a stand-alone solution or - if complete plant control and visualization is required - as a component of a fully integrated automation system with the Win CC HMI system and the PCS7 process control. In contrast to conventional material tracking systems, SILAG offers many advantages. - The Material Tracking System is an object oriented, online to the process, linked system. All changes in the plant during operation e.g. selecting another conveyor route, start and stop etc. will be automatically detected and will influence the calculation. - The systems is able to split and blend material (quantity and quality).Measurements of tonnage, volume or quality analysis can be linked online to the system. Each movement of material is monitored by the system and leads to online recalculations of the images and databases. - All material data is based on 3D-stockpile images, which are calculated by an internal mathematical model based on quantity and quality information. - If a laser scanner is available on a stockyard machine it can be taken to update the profile directly from the piles. - Efficient control and report functions are available on each, free selectable point of the total plant.

Sep 1, 2001

By V. Korobko, M. Byantogtokh, N. Byambadorzh, V. Bysov

A three-stage operative planning of mining operations in ore opencasts is considered. The hierarchy of monthly-weekly, weekly-daily, daily-shift planning is offered. For the fastest elimination and deviations in problematic situations a level is analysed and weekly-daily or monthly-weekly operative plans are being constantly updated. Operative planning is formulated on information received of preparation and working of mining panels. The electronic maps of these panels are considered for automated operative planning. On the data of the registration of blasthole drillings on a panel, the position of blasthole entry, their depth and the number of a line are determined. The geologist specifies boundaries of ore grades by the bored silt. The qualitative characteristics of ores are determined by the chemical analysis of slime or magnetic logging of blastholes. The missing geologic information is obtained by interpolation on the data of detailed and operational explorations. During working of the mining panel the technologists mark the movement of shovels, associating this movement to blastholes. For this purpose technological attributes are used: when was the blasthole drilled, what drill-rig participated in drilling, what shovel was used and when was it worked? Around each blasthole the zone of its influence is built up. It represents a discrete, elementary volume of ore or waste. The discrete form of the data is most convenient, as it allows step-by-step methods to be employed of the scheduled tasks in many and various combinations. The account panel working technology avoids ‘combination’ explosions. The elementary blocks should be placed in a trajectory of shovel movement and the trajectory can not be arbitrary. It’s determined by the technological rules of extracting and loading of mine mass. In linking to blastholes, the trajectory of shovels is simulated by the sum of step-by-step moving from one elementary block to another. For this purpose a geometrical linkage of blastholes is used. At a railway haulage, or complete mining with truck haulage, the trajectory of movement is a shuttle along the front of operations in the panel. At a selective mining of ores the number of possible directions is limited to three: moving of a shovel by idle running along the front of operations in the panel, frontal pull all the way down of the panel, and withdrawal. The technologically acceptable trajectories of shovel movement are stored for the following estimation and selection of the best. The estimation is carried out on mathematical models with criteria on the method of the least squares of deviations based on preset parameters from the plan, uniform loading of shovels, and mixing of ore at unloading points. The equations of balance type and directive parameters of the plan, as well as technological restrictions of solid and of elementary blocks within the limits of a trajectory are the restrictions of the model. Depending on an industrial situation it is possible to choose one of the predetermined models. The presented technique is used for longitudinal shovel bench at the Erdenet ore-dressing company.

Jan 1, 2003

By A. Ball

A fully instrumented laboratory drilling machine is described. It is designed to produce realistic drilling conditions with diamond microbits of 20 mm diameter. A computer-controlled data-logging system records the net power consumption, rotational velocity, bit thrust, torque, and penetration rate. Tests can be conducted under conditions of set thrust and rate of advance. In the tests reported, there is a significant correlation between the rock drilability and the measured rock properties of relative abrasion resistance and uniaxial compressive strength. Wear of a diamond bit is a crucial factor that cannot be determined simply from rock properties. Realistic drilability testing with appropriately scaled microbits is a convenient and economical way of evaluating diamond-bit performance and determining rock drilability.

Jan 1, 1990

By D. Rankin, H. J. Stucke, W. K. B. Loftus

SYNOPSIS Planning for the Finsch opencast mine is described with particular reference to the proposed stages of mining, the method used to determine the limits of surface waste rock stripping and the derivation of the waste rock mining rate. Actual mining practice is described and the possibility of installing a skipway into the open mine at a later date is discussed. In addition, the waste dumping policy is referred to: this includes the cutting of slots through the hill on the west side of the pipe to increase tramming speeds. The crushing, washing and recovery sections of the treatment plant are described together with the various changes being made to the circuit. The most important of these are the installation of X-ray sorters for the final recovery of + 7 mesh diamonds, and the vibrating grease belt for the recovery of - 7 mesh diamonds. INTRODUCTION The Finsch Mine, a subsidiary of De Beers Consolidated Mines, Limited, is situated approximately 90 miles west of Kimberley, and some two miles from the village of Lime Acres, in the Northern Cape. Lime Acres is a company village shared with the Northern Lime Company which operates a limestone quarry and works near the township. The mine is near the southern end of a well mineralized belt producing limestone, asbestos, diamonds, manganese and iron ore, and the whole area has developed rapidly in the last 20 years. Power for mining operations is drawn from the Electricity Supply Commission. The mine is conveniently close to the main Kimberley-Postmasburg railway line. Water is drawn from the Vaal River through a 57 mile State-owned pipeline at present temporarily operated by mine staff. DISCOVERY AND PROSPECTING OPERATIONS The diamondiferous orebody is situated on the farm Brits, which is State-owned ground that has been leased to the Company for the period of mining operations. There are indications of interest in the area by prospectors (Richter, de Bruin and others) over a period of some 30 years and the discovery would possibly have been made years earlier but for a law preventing prospecting for precious stones on State-owned land. Although the pipe formed a clear depression on the hill where it was situated, it was overlain by some 5 to 40 ft of banded ironstone rubble which was washed into the depression from the hillside above the pipe and obscured the deposit. In 1958, Mr Allister Thornton Fincham applied for, and was granted, the right to prospect for base minerals on the farm Brits. Asbestos is known to occur in the area and, initially, was Mr Fincham's primary interest. However, during the prospecting operations, garnets were discovered and it was realised that diamonds might be present. In 1960, when the Precious Stones Amendment Act was passed, a company

By J. Tikka, E. Bäcklund, N. -O. Lindfors

Tornados are the most violent weather events in the world, and we have all seen the forces and phenomena created by tornados in nature. Airgrinder AB has been working with a material treatment technology, which most easily could be described as an artificial tornado. The process consists principally of one air fan providing a high-velocity airstream that enters a mechanical cyclone. When the gas enters the cyclone, an outer vortex is created. This outer vortex rotates next to the cyclone wall, and at the bottom of the cyclone funnel the gas stream is turned and an inner vortex is created. The control of the air flow is tuned by a special device on top of the cyclone. The gas outlet is at the top of the cyclone and the material outlet at the bottom. The material is fed through a feeding device into the air stream channel prior to the inlet into the cyclone. The process is basically an improved grinding and dehydrating system, which is very efficient and environmentally friendly and can even be employed with very sticky materials. Also due to its rotating comminution, the material particles become rounded during grinding, hence more free flowing and easier to handle. MEFOS has already tested more than 30 different applications in the pilot equipment. The materials tested range from metallurgical slags containing 2?3% moisture to sludges with up to70% moisture. This technology has a potentially strong impact on mineral beneficiation, including the drying of sticky fine-grained materials, improved and selective gas scrubbing and the manufacture of free flowing powders.

Jan 1, 2007

By I. J. Barker

This paper argues that the scale up of furnaces and the supply of electricity are going to be two major issues that will affect the ferro-alloy industry in the near future, and that economic factors will drive this development. The most common type of furnace for producing ferroalloys at present is the submerged-arc furnace with three electrodes, fed from a three-phase AC electrical supply. The scale up of this technology has now reached a fundamental constraint, which is caused by the electrical reactance of the secondary circuit. If the economy of any further scale up is to be achieved in the future then a different technology will have to be used. The supply of electrical power in future is likely to become amore complex issue than it is at present. Existing submerged-arc furnaces tend to run at fairly steady loads, but the ability to swing the load under demand-side management may offer advantages, and may allow a furnace to obtain cheaper power from the organizations that supply this power. This will have to be counterbalanced against the nuisance factors incurred by having a varying load in the operation of the furnace. Various options are therefore discussed in this paper. The possibility of scale up of Søderberg electrodes is discussed, as well as the use of DC power and multiple electrodes. Some of the issues with load swinging are also examined. A particular scenario is also briefly presented to show that considerable further scale up of ferro-alloy furnaces is still possible.

Jan 1, 2011

By I. J. A. Brackley

An investigation of the slope stability of a pit and failures of spoil dumps, carried out at Silicon Smelters quartz mine, Pietersburg, South Africa, is described. The major geological feature of the mine is the intensely foliated schist in the footwall, with exceptionally Iow strengths upon extensive discontinuities, and the similarly unusual strength properties of the dumped schist spoil. The selection of slope angles for the pit is described, and a proposal for the stabilization of the failing spoil dump by segregated dumping is explained.

Jan 1, 1985

By C. Kirmanli

The purpose of this paper is to develop an expert system for hydraulic excavator and truck selection in surface mining. Hydraulic excavators and trucks are finding increasing applications in mining operations. Hydraulic excavators are extensively used especially when bringing electricity to rural areas is difficult and for small-scale mining. This paper describes an expert system, which selects the optimum hydraulic excavator truck configuration such that unit production cost is minimized and technical constraints such as geological, geotechnical and mining constraints are satisfied. The system has four modules: user interface, rules and an methods, databases and output module. The expert system in this study is developed within KappaPC shell. It supports object-orientated technology for the MS Windows environment. The software provides a very useful tool to practitioners, saving time and cost. Equipment selection is a recurring and expensive problem of mine planning and often involves interdisciplinary experts from different fields. It is very difficult and expensive to bring together all these experts. The capabilities of the expert system developed are illustrated in the paper. The software overcomes the difficulties of selecting the proper equipment for surface mining operations, which is very important, and results in substantial savings. Equipment databases for hydraulic excavators with 15-59 yd3 capacities and trucks with 35-360 tons are constructed and these databases are used to select the proper configuration. A case study is carried out for Soma Surface Coal mines in Turkey. Keywords: surface mining, expert systems, equipment selection, hydraulic excavators, diggability

Jan 1, 2009

By D. A. Phillips

A procedure for designing an optimum pit to yield maximum profit is described. The volume in which a possible pit is considered is divided into discrete blocks, each of which is assigned an economic value equivalent to its worth as a block of mineable material. The profitability of a pit can then be generated by summing the blocks within the pit. The optimizing procedure starts at the surface level and proceeds downwards level by level, to obtain the optimum pit at each level. The method makes use of the fact that an optimum pit at a particular level must be completely contained in any optimum pit at a lower level. Procedures for generating block costs, and pits with various slope angles under the restriction of complete block removal are considered briefly. The main description is of the theory of the method and the computer program based on this. The method is applicable to any type of mineral deposit, the only requirement being that the orebody should be represented accurately by a block model.

Jan 1, 2014

By H. Bhikha

The minerals industry is committed to the principles of sustain-ability. Reducing water consumption is a priority area, especially for regions of water scarcity. This paper presents a systemic optimization of the water balance of the Skorpion Zinc refinery with the aim of reducing water consumption. An Aspen Plus simulation of the process is used. The validity of the simulation is tested by measuring key output variables and comparing results to plant data. A number of water minimization scenarios are investigated, Including unit operation and circuit configuration changes. The scenarios leading to the largest reduction in water consumption are through the full recycle of treated effluent water, which results in water savings of up to 19%. Reducing process water and/or recycling of untreated water is prohibited by the build-up of trace elements, which affect product purity. The Skorpion process already features a highly optimized water balance, with unit operational changes merely resulting in a shift in the water balance. Consequently, the largest area for improvement is through the re-use of effluent water. Keywords Skorpion zinc water usage, process optimization, sustainability.

Jan 1, 2011

Scientific and technical research is becoming an expensive business, and needs to be managed as well as directed. Regardless of whether it operates under public or private auspices, a research-and development organization should not tolerate inefficiency or irrelevance. Its true worth is ultimately decided by the impact it makes on its environment. Doing the right things is preferable to merely doing things in the right way. Clear definition and the setting of goals form the crux of the Management by Objectives (MBO) system. This system provides the research establishment with a profound sense of purpose and direction, which is essential for effective planning and control. Performance standards, in association with costs and manpower, value assessment, feedback, and improvement, tend to follow naturally once the principle of a results-oriented management system is adopted. MBO is a participative management system, leading to decentralization and self-control of the individual rather than imposed control. If wisely implemented with the necessary respect for creative work, it can enhance the job satisfaction of the research worker as well as the overall productivity ofthe research establishment.

Jan 1, 1982

Ladies and gentlemen, it is a privilege to be able personally to welcome you to the opening of this Symposium. It is particularly pleasant to be able to extend a warm South African welcome to al our visitors from foreign shores. We trust you will enjoy your stay in our country. It is a singular honour for me to be present here today, and to have been asked to open this international Symposium. MINING IN SOUTH AFRICA Mining is the single most important contributor to this country's foreign-exchange earnings. Minerals and processed mineral products together account for about 70 per cent of South Africa's total foreign exchange earnings. The mining sector employs in excess of 670 000 people, and is one of the largest employers in the country. The construction and development of cities and towns like Johannesburg, Welkom, Orkney, Springs, Benoni, Witbank, and Klerksdorp is a direct result of the contributions of the mining industry to economic activity in these areas, as well as of the multiplier effect of secondary industries.

Jan 1, 1993

By D. Bessinger, N. Rughubir

Exxaro Sands KZN produces?among other heavy mineral products?high titania slag, which is used as feedstock to the pigment industry. The titania slag is produced from the smelting of ilmenite in two 36 MW DC furnaces. In this smelting process carbon monoxide gas is produced. This gas is cooled, scrubbed and washed to remove entrained dust. This paper provides details on the gas cleaning plant system and the chemistry, mineralogy and size distribution of the particulate material contained in the off-gas stream. Characterization of the dust shows that is consists mainly of ilmenite, but with relatively high levels of SiO2and MnO. Smelting of the dust in a 500 kW DC furnace was carried out to investigate the potential for recovering valuable elements from the dust.

Jan 1, 2007