Search Documents

By P. Jordan

The practice of ilmenite smelting in electric arc furnaces has been researched and published over the last few decades. An issue that has not been addressed is the understanding of the properties of ilmenite smelting reductants, and linking these properties to the subsequent smelting behaviour in the furnace. The reduction mechanism of ilmenite smelting is not fully understood, but it is believed that the Boudouard reaction plays a role. This paper investigates the behaviour of a number of reductants when reacted with CO2 at different temperatures. Keywords Boudouard reaction, carbon reactivity, reductants, ilmenite smelting.

Jan 1, 2011

By V. Matou?vek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007

By P. R. Mothemela

The objective of the investigation is to optimize the truck and shovel operations for pre-stripping at New Vaal Colliery by introducing campaign mining. The aim of campaign mining is to improve the efficiency of the loading, hauling, dumping, and maintenance operations which are critical to the success of truck and shovel operations. The current loading (single-sided loading method), hauling, and dumping operations at New Vaal Colliery were found to be inefficient. Time studies were used as a major indicator to highlight the inefficiency of the truck and shovel operations, and it is recommended that an improved loading configuration, hauling, and dumping operations be implemented by using campaign mining. It is also recommended that a service truck be used to maintain the pre-stripping fleet in order to reduce travelling times to the main workshop. As expected, the improved operating conditions will lead to an increase in pre-stripping production.

Jan 1, 2013

A set of six design principles for rock engineering was developed by Bieniawski: design objectives; minimum uncertainty; simplicity of design components; state-of-the-art practice; optimization; and constructability. These principles translate into a ten-step design process. Although this methodology was developed for rock engineering, it is applicable to any design process, feasibility study, etc. Diligent use of such a process will ensure that a defensible design or evaluation has been carried out. Recently a ?strategic conversation? process has been identified by Ilbury and Sunter that includes the following ten steps: scope; players; rules of the game; key uncertainties; scenarios; SWOT analysis; options; decisions; measurable outcomes; and meaning of winning. A comparison of these steps with those of the design process shows a remarkable correlation. This is perhaps not surprising since engineering design is a strategic up-front issue, and front end loading in a project is critical to achieve the expected project performance. Based on the close correlation between the strategic conversation and engineering design processes, a circular design process, rather than a linear process, is proposed. The ?circle of design? better reflects the importance of review and monitoring in the two phases of successful design and implementation?defining the design, and executing the design.

Jan 1, 2009

By R. du Preez

Tati Nickel is currently operating a hydrometallurgical demonstration plant in Botswana, using the Activox® process developed by LionOre Technology to produce nickel cathode and a cobalt salt from a sulphide concentrate. Cobalt is extracted using Cyanex 272. This reagent also extracts all the iron, aluminium, copper, zinc, and manganese from the nickel stream. Versatic 10 carboxylic acid is then used as extractant to recover nickel from the stream, separating it from calcium and magnesium, and upgrading it to provide a suitable advance electrolyte for nickel electrowinning. However, the selectivity of Versatic 10 for nickel over calcium is limited, and gypsum formation in the extraction circuit is a problem when attempts are made to maximize the recovery of nickel. Mintek has developed a synergistic system with Versatic 10 for improved separation of nickel from calcium and magnesium. Laboratory testwork was conducted on the raffinate of the cobalt solvent extraction circuit to optimize the Versatic 10/Nicksyn? (Mintek synergist) system to be employed. Extraction and stripping parameters suitable for this stream were optimized in the laboratory and then applied on the demonstration plant. A commercial batch (0.5 tons) of Nicksyn? reagent was produced for the demonstration plant. The laboratory testwork results and the demonstration plant performance are discussed in detail in this paper.

Jan 1, 2007

Underground mining and particularly dipping narrow tabular orebodies are difficult to mechanize appropriately, given the low gold price and other external factors. Particularly in the deep level mines in South Africa, there is little choice left but to mechanize if the industry is to remain competitive and a significant global player. This paper presents a design philosophy for appropriate mechanization intended to generate solutions that can be implemented using the people currently employed in South Africa mines. The design philosophy is based on the ability of high-pressure water (hydropower technology) to deliver enhanced performance to users and on simplicity in the eyes of the user. Four examples of systems and equipment are described to illustrate the approach to Appropriate Mechanization. These include: • The Development End System, • The Monorail Raise Climber, • Automatic Pump Control Valves, and • The Energy Recovery Pump. The equipment is presented with the following critical issues foremost in mind: Safety, Working Environment, Performance, Cost effectiveness and Implementation. Although the appropriate mechanization approach is described in the context of the South African underground mining industry, much of the Appropriate Mechanization equipment has worldwide applications. Key Words: Hydropower, Mechanization, Tunnel Development, Raise Development, Monorail, Raise Climber, Pump Control Valve, and Energy Recovery

Sep 1, 2001

By J. A. L. Napier

The application of excess shear stress as an aid to the design of mine layout is reviewed, and the critical parameters required to describe slip on a plane of weakness are noted. A design procedure that is required to model the cyclic build-up of excess shear stress is described. A number of simple examples of mine layouts on two reef planes intersecting a fault plane are then considered to illustrate the application of the design concept and to highlight some of the pitfals that may be encountered

Jan 1, 1987

By L. A. Vermeulen

A simple argument shows that it is impossible for the flight of a rod in contact with a litter bar in a rotary mill to be initiated at that point on the upside of mill rotation when all the forces acting on the rod are in equilibrium. The argument was confirmed experimentally in a study showing that the lift of litter bars is a function of their height, that the rod velocity at the point of departure has a significant radial component, and that the subsequent flight of a rod is along a parabolic trajectory as predicted by elementary mechanics. A quantitative account of the observed effects, which is based on a dynamic theory of the sliding interaction between rods and litter bars, revealed interesting properties of the motions of rods down the surfaces of litter bars when the latter are in uniform circular motion during the rotation of a mill.

Jan 1, 1985

By C. R. Thomas

Although stainless steels have been used to a limited extent in the South African mining industry, the metallurgical development of 3CRI2 has presented materials engineers with a viable alternative for certain materials-handling applications. The various types of wear involved in these operations are described, and an explanation is given of how 3CRI2 is able to offer advantages, particularly in wet sliding applications. Certain applications result in various types of abrasive wear, and the performance of 3CRI2 in these areas is described.

Jan 1, 1981

By K. Barlow, J. M. W. Mackenzie

Trochem (pty) Limited, which is jointly owned by Chemical Holdings Limited and Henkel Corporation of America, recently commissioned the first fatty amine plant to be built in Africa. The plant is capable of producing primary, secondary, and tertiary fatty amines with varying hydrocarbon-chain lengths. Process control Sponsored by the South African Institute of Measurement and Control, the Instrument Society of America is bringing a short course in process control to South Africa. This will be the first in a series of courses in instrumentation and process control.

Jan 1, 1982

Today's conservation thinking is becoming increasingly polarised-a widening gap that could eventually be to the overall detriment of mankind, one way or the other. In one corner, stand the disciples of the untainted wilderness, moral protectors of the natural world who subscribe to the doctrine that the fragile balance of nature is threatened by man's very existence. On the opposite side of the ring, stands the relentless developer, with the megalomaniac notion that nature is purely there to serve humanity and civilisation, under the auspices of 'progress',

Jan 1, 1996

By J. N. Van der Merwe

The South African coal-mining industry uses a uniform safety-factor formula for non-squat pillars, incorporating a coal-strength constant that was derived empirically by Salamon and Munro in the 1960s. The constant is 7,2 MPa. Since that time, collapses of pillars at relatively high safety factors have occurred in the Vaal Basin. Analysis of the post-1960s' collapses indicated that the strength constant for the Vaal Basin is 4,5 MPa. A crude method for the prediction of the minimum life span of pillars in the Vaal Basin is presented.

Jan 1, 1993

By A. V. Z. Brink, D. M. O’Connor

Recent research into the prediction of mining-induced seismic events by the monitoring of small microseismic events at Western Deep levels Gold Mine is described. Measurement and interpretation techniques and results are presented. It was found that the occurrence of the larger events near longwall faces on the Carbon leader reef is preceded for some hours by an increased rate of microseismic emission and spatial concentration of the microseismic events in the zone of eventual failure. The research is currently being expanded with the aim of producing a practical rockburst early-warning system.

Jan 1, 1983

By M. J. Nicol, G. Cromberge

An account is given of the development of a relatively simple model that describes the kinetics of the absorption of gold cyanide on activated carbon. The model is based on the treatment of the carbon solution interface as a homogeneous boundary across which gold is transported at a rate determined by the rate of mass transport to and from the interface. Rate equations derived from this model describe the results of various kinetic experiments under continuous or batch conditions in the laboratory and on operating pilot and full-scale plants.

Jan 1, 1983

By F. H. Deist, R. P. Plewman

The history of development of analytical techniques for the determination of elastic behaviour around tabular excavations, is examined briefly. The design of a completely digital system, which appears to afford considerable improvements in speed, accuracy and versatility compared with existing analogue methods, is described in detail. The practical application of this system is illustrated by means of an actual underground problem. The results are presented, not in the form of specific solutions to the mine's problems, but as indications of the versatility and scope of the new method.

By M. J. U. T. Van Wijngaarden, A. T. Pieterse

An account is given of the performance of a 37 MVA electric-arc .furnace in which bottom stirring with inert gas by an indirect-contact stirring-plug system was applied. The system, which was developed and patented by Thyssen-Stahl AG, and which is the first inert gas stirring system to be installed in South Africa, was commissioned in January 1992. Initial problems were experienced due to the blockage of stirring plugs by molten steel. The causes of these malfunctions are examined, and an account is given of how they were overcome. The system is described and evaluated. A comparison with direct-contact stirring systems shows why Iscor Vereeniging Works considered it to be more suitable for their Vaal Melt Shop. The results show that, through the successful application qf this technology, Iscor Vereeniging Works has achieved an annual cost saving of more than R2,5 million.

Jan 1, 1994

By J. J. C. Heynike

The relationship between population growth and steel consumption since the beginning of the twentieth century is indicated, reference being made to the increasing capacity of production units and the resultant increased pollution in the same area. The need for the control of fugitive emissions with its associated high cost is pointed out. There is a direct relationship between energy and pollution, and examples are given of several improvements that have been made to achieve better energy usage and reduced pollution. Several practical examples of air-pollution control systems are described as applicable to the main metallurgical steel processes of today. In conclusion, reference is made to the fact that, with the improvements attained in reducing pollution, the public will not tolerate a decline in the standards already attained. Environmental control and better energy utilization will continue to be important aspects of steel-plant design and operation.

Jan 1, 1978

By L. E. Kun, R. O. Oelofsen, E. J. J. van Vuuren

High-rate floc-blanket clarification of gold pregnant rotary filtrate was introduced at the Vaal Reefs South gold plant of the Anglo American Corporation during February 1978. A. daily 12 000 to 15 000 t of filtrate, with an average suspended-solids concentration of 350 mg/I, is continuously clarified to a concentration of less than 2S mg/I of suspended solids in a modified plant pachuca (10 m in diameter) at throughput rates of 7,7 to 8,5 ma/m2.h by the addition of 5 g/t of ferric chloride inorganic coagulant and 0,2 g/t of Superfloc NI00 flocculant. The pachuca overflow is then clarified further in seven Stellar candle pressure filters of 54,S m2 surface area to under 5 mg/I of suspended solids. The combined clarification cost when the hopper clarifier is used in conjunction with the Stellar filters is R0,0032 per ton of liquid treated, which is approximately 60 per cent lower than the cost of Stellar filtration on its own. The savings are mainly due to the reduced use of filter pre-coat, the consumption of which has dropped by 70 per cent since the introduction of hopper clarification.

Jan 1, 1979

By P. J. D. Lloyd

An account is given of the development of a process to concentrate gold and other valuable minerals and to produce a discardable waste. In this process, the ore is coarsely milled, a bulk flotation concentrate is prepared, and the flotation tailing is scavenged in a hydrocyclone, which returns coarse gangue, moderately coarse valuable minerals, and locked valuable minerals back to the mill. The engineering developments required by this circuit in order that it will fit underground, and the progress made towards the achievement of those requirements, are reviewed. If the waste is to be suitable for use as a backfill in a deep-level, flat tabular excavation, it should be capable of being placed hydraulically, and should have both low voidage and high rates of drainage. Such a material could be prepared by the fine screening of the overflow from the cyclone in the proposed circuit. Possible methods for the handling of the concentrate and the recovery of its valuable constituents are described. The paper concludes with a discussion of the possible benefits from the use, in deep-level Witwatersrand mines, of a system involving concentration underground, extensive backfilling using the tailings from the concentration process, and hydraulic hoisting of the concentrate.

Jan 1, 1979

By P. M. Vercruijsse

Dredging is an industry in constant transformation. It has changed tremendously in the last decades. The traditional dredging activity, like construction and maintaining ports and harbours, desilting of drainage and irrigation channels, keeping reservoirs at depths and removing sediments from waterways, is still of importance. However, it is surpassed by other applications of dredging technology. Reclamation is an important example, where large amounts of sand are dredged, transported over large distances and used to make new land for industrial, housing, airport and other infrastructural purposes. Beach nourishment and other protective measurements should be mentioned here as well. Other applications like offshore winning of oil and gas, environmental clean-up, mining of interesting minerals like gold, diamonds, titanium and tin as well as aggregates from inland and offshore deposits are of importance. For all of these dredging applications equipment is required, and with changing circumstances and constraints, the design and use altered significantly. Larger dredging depths and increasing capacities require an impressive scale-up of equipment and tools. A demand for higher accuracy and selectivity set the requirement for a higher level of automation and control in combination with a well trained crew. Operations under more difficult circumstances and with other soil characteristics necessitated the development of new dredging components and systems. A sound basis for all developments was and still is a better understanding of the various dredging processes. This paper will highlight some eye-catching developments in the dredging industry. It will focus on issues in the field of hydraulic transport such as ever increasing capacity and dredging depth, as well as the pumping of large size materials.

Jan 1, 2007