Search Documents

By M. J. Nicol

This paper ,examines the kinetics of the extraction of uranium from acid sulphate solutions by strongbase anionexchange resins. Parameters such as the concentration of uranium in solution. the agitation of the resin beads in solution. the size of the resin beads. and the degree of cross-linking within the resin matrix were varied. and the effec ts on the kinetics are reported. The applicability, of various empirical kinetic models to the description of the data is assessed, and an attempt is made at the modelling of the rate data in terms of established theories about the diffusion of ions through films of stagnant liquid and through spherical beads of resin.

Jan 1, 1980

By J. Meintjest

As you pointed out, furnace power factor (and consequently transformer MVA rating) depends upon the inductive reactance, and so it is desirable to design for the lowest possible value of this parameter. The further introduction on the primary side of the transformer of capacitors, whether in shunt or in series, increases the network power factor but does not alter the furnace power factor; that is, the phase angle between electrode to- hearth voltage and current remains unchanged. Corrigenda The following amendments should be made to the article entitled 'Coal-preparation routes for maximum coal recovery', which was published in the August issue (vol. 80, no. 8) of this Journal:

Jan 1, 1980

By H. T. Kaiser, P. De Waal

The Alusaf aluminium smelter at Richards Bay by H. T. KAISER, B.Sc. (Pta), M.B.L. (Unisa) (Visitor) and P. DE WAAL, B.Sc., B.lng. (Mech.) (Stell.) (Visitor) A description is given of the aluminium smelter at Richards Bay, which operates on the Hall-Heroult electrolysis principle. The annual output of metal (average 99,7 per cent aluminium) is approximately 7S 000 tons. Since its commissioning in 1971, the plant has fulfilled South Africa's total demand for low-alloy rolling slabs, extrusion billets, remelt ingots, and electrical conductor rod. The plant layout allows for sufficient expansion of its capacity to meet longterm increases in demand.

Jan 7, 1977

By N. von Stade, G. du Plessis, W. van Niekerk, H. Bosman

Exploration, and other, boreholes are drilled to obtain information about the geological environment. Knowledge of the exact position (dip and direction) of the holes is important to ensure compatibility between the hole and the geological information. Kumba Resources traditionally used mechanical methods to determine the hole characteristics. These are cumbersome and expensive, and as a consequence a new method, the IVEC (Iscor Video Exploration Camera), was developed which utilizes a charged coupled device (CCD) image sensor focused on a three-dimensional compass. This system is rugged, relatively inexpensive and gives real-time results during borehole logging. Keyword: Borehole inclination, deviation, dip and direction, geophysics, exploration.

Sep 1, 2001

By N. O. Lotter

Evaluation errors and value frequency distribution models of the gold ore bodies in the Witwatersrand and Free State systems are reviewed. It is found that the low-grade sections of the data are prone to the largest evaluation errors, and that an understanding of the shape of the value frequency distribution is essential to the calculation of mean grade. The evaluation of a mineral process for a particular ore requires attention to mil-feed sampling, sample processing, and monitoring. In particular, the calculation of a representative mass of mill-feed sample (Ms) should take account of size-by-size value variance. Alternative Ms models are discussed.

Jan 1, 1995

By G. E. Blight

It is shown that the profiles of beaches of hydraulic-fill tailings dams can be predicted with good accuracy the use of small-scale laboratory deposition tests on materials from a prototype tailings dam. Although the slope of a tailings beach at any point is related to the shear strength of the settled slurry, are severe practical difficulties in the prediction of beach profiles from shear strengths measured in the laboratory. The hydraulic sorting of particle sizes that occurs on a tailings beach results in a gradient of permeability the beach, and this gradient has the significant effect of lowering the phreatic surface in the tailings dam.

Jan 1, 1985

By R. M. Stroh, D. F. H. Grave

In this paper ventilation planning methods are discussed, with particular reference to the application of computer techniques to the solving of the many problems associated with the forecasting of ventilation and refrigeration requirements in mines of high production rates going to depths and rock temperatures higher than previously experienced. The use of the Starfield-Dickson programmes for calculating heat flow into airways and advancing stopes is demonstrated in the case of ventilation planning on a large mine extending to a brief depth of over 3 km below the surface. The possible effects of new mining methods on ventilation requirements in the future is briefly discussed.

By Page-Shipp. R. J., Elizabeth Harris

A study of the response of South African white gold miners to exposure to dust in their working environment yielded large quantities of dust data. Analysis of this data (presented in summarized form) reveals a variety of interesting relationships, including the shift-long exposure of different occupational groups, the dust levels due to various mining operations, relationships between different dust-measuring procedures and time trends in dust levels during the shift. The statistical probability of contracting silicosis at various levels of exposure to this dust is reported briefly. A new method of using microscope counts to estimate the respirable mass of dust samples is given in an appendix.

By M. Guarascio

Microseismic monitoring of mining areas is a developing technique, described here for the Belvedere Spinello Mine, southern Italy, where dissolution cavities in the mining area have proved problematic. The preliminary condition for locating seismic impulses has been found to be a reliable seismic ground model. Ground signals are continuously recorded by means of data from piezometric wells, for sinkhole data, and linked gephones, for microseismic data. A computer system has been implemented to collect, analyse and interpret the incoming signals consequently, identification and classification of hypocentres of activity is facilitated, with advantages in terms of safety, preventing harmful side-effects, including rock bursts, and for environmental conservation.

Jan 1, 1987

This paper describes an interactive personal computer program, ENVIRON, which simulates cooling and ventilating systems on gold mines. An example of the practical application of the program is given and proposed future developments are discussed. The program consists of two main modules, HEATFLOW and VENT- FLOW. HEATFLOW calculates the heat loads and the effect of air coolers, while VENTFLOW estimates the air flow distribution. As the calculation of the heat loads requires a knowledge of the air flow and vice versa, the two modules are run iteratively until the solution converges. The program is written in Pascal and runs on any IBM-compatible personal computer.

Jan 1, 1987

By A. Koning

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry?s experience base. The method of designing a refractory lined vessel is examined taking into account the impact of irreversible chemical swell, operating factors, design factors, and installation factors. The effect of geometry and incorporating additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional finite element analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed. Keywords refractory lining design,autoclave, finite element analysis.

Aug 1, 2013

By N. J. Roodt

Mine dumps created in terms of the pre-MPRDA regime (old order mine dumps) are currently not regulated by the MPRDA, and the common law owners of such dumps are free to process them without the need to obtain the relevant rights. The MPRDA Amendment Act purports to change this position. However, the wording of the Amendment Act raises a number of problems which render the post-amendment position at best unclear and at worst absurd and unworkable. The primary concern with the Amendment Act is that, on one interpretation, material placed on the same dump at different times may be treated differently at law. Thus, parts of a dump may be subject to one person?s right while others may be subject to another?s right. Moreover, case law has generally regarded mine dumps as movable property and, by extending the MPRDA to apply to all mine dumps, the Legislature is extending the ambit of the Act to cover movable property, a scenario not contemplated by the wording of the Act (even after its amendment) in relation to applications for rights. The better interpretation of the amendments, which are not yet in force, is that they will not apply retrospectively to old order mine dumps.

Jan 1, 2010

The development of short- and medium-term mine production schedules in isolation from each other has meant that only a local optimum can be achieved when each scheduling phase is carried out. The globally optimal solution, however, can be achieved when integrating scheduling phases and accounting for the interaction between short-term and medium-term activities simultaneously. This paper addresses the task of integrating short- and medium-term production plans by combining the short-term objective of minimizing deviation from targeted mill feed grade with the medium-term objective of maximizing net present value (NPV) into a single mathematical optimization model. A conceptual sublevel stoping operation comprising 30 stopes is used for trialling segregated and integrated scheduling approaches. Segregated medium- and short-term scheduling using separate models achieved an NPV of $42 654 456. The final scheduling approach involved integrating the two scheduling horizons using the newly-developed globally optimal integrated production scheduling model to achieve an NPV of $42 823 657 with smoother mill feed grade. The larger the stope data set, the larger the difference between the two scheduling approaches is likely to be. At the very least, an integrated approach ensures feasibility across the two scheduling horizons, which cannot always be assumed when using a segregated approach.

Jan 1, 2012

By H. D. Mtegha

Mining is important to the economies of both Tanzania and Namibia. Recently, both nations revised their national mineral policies to ensure future economic benefit. The main difference in the mineral policy-formulation processes followed by the two countries is identified as the degree and timing of stakeholder involvement during the articulation process. In the case of Namibia, the stakeholders were involved from the start in identifying issues and in suggesting policy solutions. In contrast, the Tanzanian process involved stakeholders after a framework had been developed by a task team. The Tanzanian emphasis was on attracting foreign investment into a traditionally state enterprise system of mineral investment and development. One can argue that the policies developed met the initial requirements, and both are, therefore successful, despite the different processes of policy formulation that were used. However, several fundamental questions arise as a result of the two approaches. This paper attempts to answer these questions by providing a comparison of the processes used for developing and formulating the mineral policies of Tanzania and Namibia. It concludes that the Namibian consultative process is perhaps more sustainable in the long-term because of its wider public support. Time will tell which of these policy-formulation processes provides a basis for sustainable economic growth for developing mineral economies.

Jan 1, 2010

By B. P. Watson

The Bushveld platinum group metal deposits in South Africa are the largest in the world. These deposits occur as two distinct stratiform tabular ore bodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2300 m. The mining method is a variation of planar open stoping. Crush pillars are widely used to support the open stopes. These pillars are designed to fail and the residual strength provides the required support resistance to stabilize the stoping excavations. This paper describes the in situ measurement, of stress within a Merensky pillar from Impala Platinum. These measurements were used to derive a stress-strain curve that includes pre and post failure behaviour. 2D FLAC modelling, with strain softening, was done to investigate how damage expands into the hanging- and/or footwall. Although the so-called ?squat? effect is always present, the modelling suggests that it does not dominate the pillar system behaviour at larger width to height ratios. Punching of the pillar into the hanging- and/or footwall increasingly controls the pillar system behaviour with larger width to height ratios. The paper investigates the behaviour of a system that incorporates the immediate hanging- and footwall, as well as the pillar itself.

Jan 1, 2009

By R. E. Gürtunca, D. J. Adams

Writen contribution by J.F.Curtls The subject mater of the paper is interesting in that, instead of 'numerical modeling based on elastic theory' being used for the prediction of energy release rate (ERR) in relation to various types of stope support, including backfil, use is made of stresses in the backfil in an atempt to corect the numerical modeling. Authors' reply to J. F. Curtis We thank Mr Curtis for his contribution to our paper. First of al, it should be emphasized that the object of the paper is not to address the validity of ERR as a tool for the assessment of seismic events or rockbursts, but to determine an in situ modulus for the rockmass with the aid of backfil measurements. Writen contribution by T.R. Stacey Although the authors of the above-mentioned paper have presented some good and interesting information, the title of the paper, and the recommendation that such an in situ modulis should be used for calculations of energy release rate (ERR), are viewed with some concern. The reasons for this concern are as follows. Authors' reply to T.R. Stacey Dr Stacey's comments on our paper are appreciated; we should like to address his concerns as follows.

Jan 1, 1991

By R. P. King

The flotation behaviour of phoscorite from the Phosphate Development Corporation was measured in a pilot plant, the flotation cells in the plant being varied in configuration so as to operate with or without circulating loads. The ore was floated in a batch cell so that the parameters for a kinetic model could be estimated, and these parameters were then used in a flotation-plant simulator, which is based on the kinetic model, in the prediction of the performance of a pilot flotation plant operating on phoscorite. The simulator predictions compare well with the measured performance of the ore in the pilot plant, but the comparison shows that the kinetic model is not completely adequate for the prediction of performance in continuous flotation plants. The model is weakest in its ability to model the behaviour of the froth phase. The flotation behaviour of the ore could be adequately described when it was assumed that the apatite and gangue each consist of floatable and unfloatable components. The effect of particle size on the specific flotation-rate constant of apatite was found to have a maximum at 85 µm and to fall to zero at 400 µm that for the gangue had a maximum at 50 µm and was zero at 350 µm.

Jan 1, 1978

By H. W. Read

The South African platinum industry finds itself in the midst of a rapidly evolving society that is no longer characterized by the apparent stability of the previous decades. The features of this society include increasing global competition, rapid technological innovation, a declining skills pool, major political transformation, a more challenging working environment as the mines reach deeper into the earth?s crust and a greater concern for human welfare. It is therefore axiomatic that new ways will have to be found to engage the all-pervasive change in the mining environment. Although in general terms project management is a universal endeavour for managing change, it takes place in a specific socio-techno-economic environment and geographical setting that gives it a particular context. The argument of this paper explores, analyses and synthesizes the impact of these changes on the emerging project management methodology. In essence, the management of change will inevitably contribute to the emergence of new dilemmas, issues and challenges. The change management process and procedures will also be affected by this change and in response, drive internal change of its own structures and organization. And, therefore, a new paradigm of project management will become apparent. A new project management model will then be proposed to the industry.

Jan 1, 2006

By H. Scott-Russell

Ladies and Gentlemen. It is my great pleasure on behalf of The South African Institute of Mining and Metallurgy and The Geological Society of South Africa to welcome you to the 15th CMMI Congress and to Southern Africa. It is a great honour to be hosting this event and we have been looking forward to it for a long time. I am sure the technical discussions and visits will be of great value, and I am confident you will return with pleasant memories of places and people in South Africa and neighbouring countries. The theme of this Congress, Resources and Technology', is appropriate for discussions on the ways and means of going forward in the minerals industry to create the employment and wealth so sorely needed in this region. The technical programme will give mineral industry professionals from different parts of the world the opportunity to share experience and expertise for the purpose of making operations more productive, safer and environmentally acceptable to the world at large. Delegates will be exposed to current technical developments by means of 133 papers prepared for the congress: 30 on geological subjects, 45 on mining, 29 on extractive metallurgy, and 29 in the field of metals technology.

Jan 1, 1994

The Centenary Luncheon for Past Presidents was held on Thursday, 24 March, 1994 at The President's Room at Gold Reef City, Johannesburg at 12:30. Herewith the proceedings that followed. Dr H. Scot-Russell It is with great pleasure that my fellow Office Bearers and I welcome you, our Past Presidents, to this luncheon to mark the centenary of the SAIMM. Today one hundred years ago, a group of professionals met and agreed to draw up the constitution and by-laws of a society later to be called an Institute. The Presidents of the Institute, of course, become its Past Presidents and help to guide its progress. A number of our sister institutes cannot wait for their Past Presidents to move of their councils, and cannot understand how we can give such free reign to ours! We believe it one of our strengths. The successful cooperation between our Past Presidents and ourselves is due to the personalities of these men. They attend meetings not to ensure that the status quo is maintained, but allow the current Office Bearers freedom to lead the Institute as they think fit. But they are always present to give sound advice, a helping hand, and support to the Institute in every way.

Jan 1, 1994