Search Documents

By K. N. Karparov

The stress state on two slope profiles overlying an inclined surface with layer inclination of 50 and 150 are investigated. It is demonstrated that the induced stress state in an imbedded weak layer, exposed at the base of the slope, forms a zone of induced tensile vertical and horizontal stresses, which can lead to failure. The zone length depends on the slope angle and the angle of the inclined layers. L’état des contraintes sur deux profils en pente en superposition sur une surface inclinée avec une inclinaison de couche de 5o et 15o est étudié. L’étude présente démontre que l’état induit des contraintes dans une couche faible insérée, exposée au bas de la pente, forme une zone de contraintes de traction induites horizontales et verticales, qui peut amener à la rupture. La longueur de la zone dépend de l’angle de la pente et l’angle des couches inclinées. Die Druckvorkommnisse zweier Hangprofile auf einer schrägen Fläche mit einer Schichtneigung von 5º und 15º wurden untersucht. Es zeigte sich, dass die induzierten Druckvorkommnisse in einer eingebetteten schwachen Schicht, die am Hangfuße offen liegt, einen Gürtel induzierter vertikaler und horizontaler Zugkräfte bildet, die zum Zusammenbruch führen können. Die Gürtellänge ist von der Neigung des Hanges und der Neigung der schrägen Schichten abhängig.

Jan 1, 2003

An evaluation was made of the wear and performance characteristics of liter bars, and the cost-life effectiveness of backing materials for rotary-mil liners. In a large run-of-mine mil in which the liter bars were mounted on grid liners of austenitic manganese steel (AMS), the liners had an average life that was five to six times that of equivalent unprotected liners. For a single mil, this is equivalent to annual savings in the cost of materials of up to R320 000, and to a downtime of 100 hours. Of the five materials tested in a large pebble mil grinding quartzitic ore, AMS grids and 'white iron' blocks performed best on a cost-life basis, with possibly improved performance from a real white cast iron. (The 'white iron' was shown by microstructural analysis to contain flake raphite and pearlite, being in reality a grey cast iron.) The high-chromium white iron had by far the longest predicted life, with mild steel a surprising second. Rubber was shown to last well in this type of mil. The wear rates of liners change during their lifetimes. The protective effect of liter bars was clearly illustrated by the reduction of over 40 per cent in the wear rates of the liners when the lifter bars were renewed to a height of 80 mm from a fully worn height of 35 mm.

Jan 1, 1991

Proceedings of the Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry, Montreal, June 1970. The Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry was sponsored by The Canadian Institute of Mining and Metallurgy, McGill University and Ecole Poly technique. The programme included 71 papers on various topics, as follows: Market Analysis and Logistics Planning; Quantification of Geological Variables; Blending; Capital Investment Decisions; Mining; Financial and Economic Analysis; Search for Mineral Deposits; Market Forecasting and Strategies; Operations Research in Process Modelling; Ore Reserve Estimation; Management Information Systems; Optimization and Control of Mineral Processes. In addition to general sessions, a special feature of the Symposium was Executives' Day, which was held to provide top and middle management with a broad understanding of the usefulness of decision-making techniques and their role in the mining organization. Panel Discussions and two keynote speakers provided a review, in non-technical terms, of the areas in which decision-making techniques have proven valuable. The present volume contains 65 papers submitted for publication, along with a complete account of the Executives' Day discussion. It is broadly divided according to the above subject headings. Approximately 550 pages, illustrated. Price: $15.00; $12.00 to students, plus 50 cents for handling costs. Order now from CIM headquarters: Canadian Institute of Mining and Metallurgy, 906-1117 Ste. Catherine St. W. Montreal 110, Quebec.

The Canadian Institute of Mining and Metallurgy. Milling practice in Canada. CIM Special Volume 16. 1978. The purpose of this volume is to up-date The Milling of Canadian Ores, which describes Canadian mineral. processing plants and gives other metallurgical information, and was published by the Sixth Commonwealth Mining and Metallurgical Congress in 1957. NIM reports Report no. 1874 Activation analysis and classification to soune of samples from the Kimberley Reef conglomerates. (10th Mar., 1977; released Jun. 1978). Report no. 1926 The analysis of anode sludges by X-ray-fluorescence spectrometry. (5th Jun., 1978). Report no. 1936 The analysis of mineralogical and metallurgical materials. A guide to the analytical techniques and instrumentation available at the National Institute for Metallurgy. Report no. 1959 The slag-metal equilibrium, and the activities of slag and metal components in the production of high-carbon ferromanganese. (15th May, 1978). Report no. 1965 Analyses, by several laboratories, of three ferromanganese slags. (22nd May, 1978). Report no. 1968 The influence of carbonaceous reducing agents on the rate of reduction of representative manganese and chromium ores. (28th May, 1978). Company Affiliates Guide To The Preparation Of Papers for Publication In The Journal Of The South African Institute Of Mining And Metallurgy The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal.

Jan 1, 1979

By P. Valicek, M. Farren, G. Harrison, G. van den Berg, P. van Dorssen, P. Kramers

Full mechanization of the stoping operation using rockbreaking methods other than blasting has been a target of research for decades because of the considerable payoffs in terms of increased face advance rates, productivity and safety. However, the unavailability of economically viable rock breaking tools has prevented progress so far. This has changed with the invention of activated cutting tools, which achieve significantly reduced operating forces, power consumption and wear compared to non-activated tools and thereby permitted the development and evaluation of the first mining system using this technology. Targets for the mining system were a face advance of 100 metres per month on a double shift basis for a 30 metre long panel and eventually fully automated man-free stoping. The purpose of this paper is to describe the design, development and evaluation of the mining system. This was a major collaborative effort between Anglo Platinum’s Rustenburg Platinum Mines Rustenburg Section — Townlands Business Area, Anglo Platinum’s Research and Development Department within the Mining Technology Division, the inventor of the technology Bechem GmbH, the equipment manufacturers Long-Airdox Ltd and Zollern GmbH, and CSIR Miningtek who managed the project. A structured process was followed during the development to minimize the risks involved in using such leading edge technology. The system was rigorously evaluated to ascertain the economic viability of the method and to collect data for the design of a production system.

Sep 1, 2001

By P. Horrell, K. Rhodes, G. Harrison, J. Dean, D. Sammons, M. Stander

Anglo Platinum have perceived a need to increase the rate of reef development both for new mechanised stoping technology and on conventional new developing mines. The Research and Development Division of Anglo Platinum therefore initiated an experimental reef raise project with a tunnel boring machine (TBM) at Bafokeng Rasimone Platinum Mine (BRPM). The scope of the trial was for the boring of a reef raise 340 metres in length on the Merensky Reef. The boring phase of the trial took place over six months and the average rate of penetration of the TBM was 0,47 metres/hour. TBM utilisation was 22%. The TBM used in the trial was a Jarva MK6 manufactured in 1972 and its design with its backup system was not considered to be an ideal machine for reef development. However it was the intention of the trial to prove the concept of developing with a TBM on reef. In this respect the trial was unequivocally a success. There were many problems and long delays did occur during the boring phase. Nevertheless there is every confidence that a new TBM can be designed specifically for this type of work that will achieve high rates of advance up to (say) 400metres/month and with a more flexible steering system in order to negotiate reef changes. It can therefore be expected that TBMs will be used in the future for reef development on South African platinum mines.

Sep 1, 2001

By R L. Bowers, D S. Smit

In light of soaring commodity prices, Nkomati has investigated the potential of processing additional low grade nickel ores to add to their reserves. The Chromititic Peridotite Mineralised Zone (PCMZ) was identified as one ore type with the potential of producing a high grade nickel concentrate. In addition to the nickel, copper, cobalt and PGM?s, the ore also contains a significant amount of chromite which adds substantial value to the project. Pyrrhotite, pentlandite, chalcopyrite and chromite are the dominant minerals within the ore, which on average grades around 0.23% Ni and 12% Cr2O3. The PCMZ ore contains excessive amounts of fibrous silicates which makes it a challenging float, with gangue control as the key element to success. Extensive laboratory testwork, which eventually led to a pilot plant campaign, was undertaken with the aim of developing a process route for treating the PCMZ ore. Several flotation circuit configurations were tested and results from the optimal circuit indicated that a nickel concentrate grading at 8.5% is achievable at a recovery of 78%, with substantial recoveries for the copper, cobalt and PGM co-products. The chromite concentrate, grading at 45%, was extracted from the flotation rougher tailings via a spiral plant. These promising results were incorporated into the plant design and are currently being evaluated in a bankable feasibility study, which will see the current 100ktpm MMZ concentrator being upgraded to a 250ktpm PCMZ concentrator as part of Nkomati?s Phase II expansion.

Jan 1, 2007

By D. G. Davies

Colloquium on the construction of Slimes dams The following contributions to the discussion at the above Colloquium were received for publication. D. G. DAVIES* This contribution is really a follow up on Mr H. E. Cross's paper on the conversion of a uranium plant to the recovery of zinc (published in the Journal, November 1973). Ecological aspects of slimes-dam construction by H. T. CLAUSEN C. M. VAN STADEN* Published in the Journal, December 1973 I should like to thank Mr Clausen for his paper and to congratulate the Research Laboratories and the Vegetation Unit of the Chamber of Mines on the excellent work they have done in the past, are still doing at present, and, we hope, will continue to do in future, on the testing of various methods for the covering of slimes dams and specifically on the vegetation of dams. The impact of slimes-dam formation on water quality and pollution by R. T. RUDD* C. M. VAN STADEN Published in the Journal, December 1973 I should like to congratulate Mr Rudd on the paper he presented. Congratulations are also due to the Department of Water Affairs for the practical attitude they have taken in implementing the Water Act. Slimes-dam construction in the gold mines of the Anglo American Group by W. T. RUHMER W. R. FLOOK* Published in the Journal, February 1973 Methods for the construction and operation of slimes dams in the gold-mining industry do not appear to have changed much for some considerable number of years.

Jan 3, 1974

The industrial relations handbook, by A. Pons. Juta (P.O. Box 14373, Kenwyn 7790). 1989. "'"250 pp. Looseleaf binder. R180 + GST. Industrial laser materials processing. World Business Publications Ltd (4th Floor, Britannia House, 960 High Road, London N12 9RY, England). 1989. 180 pp. £310. Mining 1990. Longmans, Financial Times International Year Books, 1989. 592 pp. £90.00. Innovations in materials processing using aqueous, co/oid and surface chemistry, by F.M. Doyle, S. Raghavan, P. Somasundaran, and G.W. Waren (eds.). 300 pp. $125. Light metals 1989, by P.G. Camp bel (ed.). No. of pp. not available. $150. Process control and automation in extractive metalurgy, by R. Partelpoeg and D.C. Himmesoete. 225 $98. Process mineralogy VIl, by D.J. Carson and A.H. Vassiliou (eds.). 4oopp. $150. Super plasticity and super plastic forming, by C.H. Hamilton and N.E. Paton (eds.). 700 pp. $140. Supera/oys 1988, by S. Reichman, D. Duhl, G. Maurer, S. Antolovich, and C. Lund (eds.). 880pp. $99. Surface modification technologies, by T.S. Sudarshan and D.G. Bhat (eds.). 305 pp. $49. World survey of nonferous smelters, by J .C. Taylor and H.R. Traulsen (eds.). 365 pp. $90. Second Parsons International Turbine Conference. London, The Institute of Metals, 1989.270pp. £40. Mineral processing in the United Kingdom. London, Institution of Mining and Metalurgy, 1989. £25. Today's technology for the mining and metalurgical industries. London, Institution of Mining and Metalurgy, 1989. 623 pp. £60. 1989/1990 E&MJ international directory of mining. Chicago, Mining Information Services (P .0. Box 6500, Chicago, IL 60680, USA). 620 pp. US$95. Advances in project scheduling, edited by R. Stowinski and J. Weglarz. Amsterdam, Elsevier, 1989. 540 pp. Dfl. 270. Proceedings of the 3rd International Conference on Molten Slags and Fluxes. London, Institute of Metals, 1989. 335 pp. £38. Brochure on industrial screens. Obtainable from Philippe Lavernhe, Johnson Filtration Systems S.A., Z.I. Availes-en-Chatelerault, 86538 Naintre, France. 16 pp. Free. Numerical techniques, edited by P. Spiling. London, The Institute of Metals, 1989. 226 pp. £25. Phase diagrams of ternary iron aloys, Part 2, by V. Raghavan. New Delhi, Indian Institute of Metals, 1988. 360 pp. £95 (from the Institute of Metals, London). cas publications These publications are available from the Centre for Resource Studies, Queen's University, Kingston, Ontario K7L 3N6, Canada. Economic aspects of gold exploration: How much is too much, by B.W. Mackenzie and M. Dogget. 30 pp. $10.00. Mineral exploration and mine development potential in Ontario: Economic guidelines for government policy, by B.W. Mackenzie, M. Bilodeau, and M. Dogget. 180 pp. $25.00. Economic potential of base metal and gold mining in Newfoundland: Assessing the impact of regional developmentpolicy options, by B.W. Mackenzie, M. Bilodeau, and M. Dogget. 188 pp. $25.00. Publications of the AusIMM The folowing publications are available from The Australasian Institute of Mining and Metalurgy, P. O. Box 122, Parkvile, Vic 3052, Australia. Prepayment is required with al orders. The AusIMM 1989 Annual Conference 1989. $A 50. Mineral fuel alternatives and the greenhouse efect. July 1989. A$ 35. NQ gold '89. Apr. 1989. $A 50. Second Large Open Pit Mining Conference. Apr. 1989. $A 50. Explo '88. Nov. 1988. $A45. Mineral deposits of New Zealand, edited by Dr D. Kear. Monograph 13. 244 pp. $A 60. Field geologists' manual, compiled by D.A. Berkman. 3rd edition. 1989. : 350pp. $A45. The rocks speak. Essays in geology-some personal responses of a wiling listener, by Haddon F. King. 300pp. $A45.

Jan 1, 1990

National Coal Board. Gate belt conveyors. London, H.M.S.O. (Price 95p.) Although the preface of this handy little book states that it has been written for the guidance of miningoperation trainees, it will prove valuable to the practising engineer as well. NIM reports Report no. 1733 A mineralogical investigation of weathered carbonatite from Salpeterkop. (14th Apr., 1975; re-issued 28th Feb., 1978). Report no. 1823 The recovery of gold and pyrite from a residue dump at Crown Mines. (10th Jul., 1976; re-issued 28th Feb., 1976). Report no. 1829 An investigation of weathered carbonatite from Salpeterkop. (20th Jul., 1976; reissued 28th Feb., 1978). Report no. 1932 A BASIC computer programme for the evaluation of intensity data from the Telsec Lab-X-250 Analyser. (12th Jan., 1978). Report no. 1940 The extraction of the noble metals with n-octylaniline,and its application to the analysis of platinum-bearing materials. (30th Jan., 1978). Report no. 1945 Analyses of the NIMROC reference samples for minor and trace elements. (28th Feb., 1978). International futures conference A conference entitled 'The Road Ahead' is being organized by the 1820 Settlers National Monument Foundation to be held in Grahamstown from 3rd to 7th July, 1978. Conference of metallurgists The technical programme has been established for the 17th Annual Conference of Metallurgists sponsored by the Metallurgical Society of the Canadian Institute of Mining and Metallurgy. This year the Conference will be held in Montreal, Quebec, on 27th to 31st August, 1978, together with the 8th Hydrometallurgy Meeting.

Jan 1, 1978

Specifile compendium' 80. Mining and engineering. (Obtainable from Specifile, P.O. Box 7870, Johannesburg 2000.) Reviewer: J. D. Austin SKF Steel. Plasmasrnelt information brochure. Hofors (Sweden), SKF Steel, 1980. Reviewer: N. A. Barcza POTENTIAL VALUE OF COLLIERY DISCARD MATERIAL By R B MacGillivray, Pr Eng, BSc(Eng) Rand, C Eng (Fellow) Preprints of perhaps the most thought-provoking of the papers delivered at the Witbank Coal Colloquium - 'Potential value of colliery discard material' by Roy MacGillivray of Rand Mines - are available on request from the South African Institute of Mining and Metallurgy. Mr MacGillivray outlines an imaginative plan to utilize the annual nine million tons of colliery discard in the WitbankBethal areas. Two SAIMM colloquia The South African Institute of Mining and Metallurgy (SAIMM) is organizing two one-day colloquia in the State Pavilion, Milner Park showgrounds, Johannesburg, to coincide with the Electra Mining Exhibition on 16th and 17th September. Over a million rands worth of equipment will be on display, the Electra Mining Exhibition being rated among the four or five largest in the world. The 1978 Electra Mining Exhibition was attended by 24 000 visitors. "Project Management in the Metallurgical Industry", "Mine Fires" APCOM International Conference by H. W. GLEN The 17th APCOM Conference (under the auspices of the Council for the Application of Computers and Mathematics in the Mineral Industries) was to have been held in Moscow during the last week in October. South Africans have always given enthusiastic support to the APCOM series of meetings, since their inception in 1961. The conference was held in the Republic in 1972.

Jan 1, 1980

By H. W. Glen

The National Institute for Metallurgy - usually referred to as NIM - has become the Council for Mineral Technology, or Mintek. The Honourable F. W. de Klerk, Minister of Mineral and Energy Affairs, announced the change of name at the official opening of the main entrance to Mintek's premises on 30th October, 1981. Awards for bravery Two men who disregarded the dangers of fiercely burning timber and falling rocks to douse an underground fire, using their hard hats to scoop water from a drain, received the Chamber of Mines Award for bravery at a ceremony held at West Driefontein Gold Mine near the end of October.

Jan 1, 1981

By F. L. D. Cloete, M. C. Coetzee

This study was aimed at a comparison of the efectiveness of a new axial-flow type of mixer impeller (the Prochem design) with the traditional inclined-blade turbine. The intended application of the mixers was in carbon-in-pulp plants for the extraction of gold from cyanide-leached pulps. The first part of the project involved water and ion-exchange resin, and measurement of the power drawn by the various sizes of impeller to fully suspend the resin. The rate of reaction between the resin and the solution was measured as a function of the power input to the mixer. In the second part of the project, use was made of activated carbon, silver cyanide solutions, and ore pulps. The rate of absorption of silver from the solutions and pulps was determined, as well as the rate of attrition of the activated carbon caused by the various impellers in clear water. The Prochem design of axial-flow impeller was shown to fully suspend solids at only one-quarter of the power requireabyan inclined-blade turbine of similar size. The axial-flow pattern produced was responsible for the more uniform vertical concentration profile of suspended beads produced by the Prochem design. These measurements verified the observations of other researchers that the rate of reaction is not affected by the ;design of impeller provided that al the solids are fully suspended. The Prochem design of impeller therefore achieved the same reaction rate as the conventional turbine at a quarter of the power input. The atrition rates of activated carbon could be correlated, in terms of the energy absorbed, by the same equation for al the impellers. Higher concentrations of activated carbon increased the amount of carbon fines produced. These results emphasize the importance of designing mixers for minimum power consumption.

Jan 1, 1989

By John Freer

As an innovation on the annual programme, the Excursions Sub-Committee organized a social get together of the Institute's Councillors and their families on Sunday, 27th February, 1983. Asian Mining - change of date The Second Asian Mining Conference, previously announced as being held in Manila, The Philippines, from 5th to 8th November, 1984, will now be held in Manila from 11th to 14th February, 1985.

Jan 1, 1983

By Dr Peter Laxen

Dr Peter Laxen, the Mintek Consultant on gold and uranium, has won the 1982 award of the Percy Fox Foundation. The presentation was made by the Minster of Finance, Mr Owen Horwood, at a banquet on 6 March.

Jan 1, 1982

By J. H. Bulloch

A study of fatigue-crack growth in a rail steel and an associated weld metal showed that fatigue cracks in the deformed rail steel had slightly higher growth rates than in undeformed rail steel. The crack growth in the weld metal was appreciably faster than either and exhibited plateaux that were above the upper bound reported for rail steels, The cyclic-life curves showed that, over an indicated service period of 8 years, both the deformed and the undeformed rail steels should not be prone to fatigue failures under the defined mechanical conditions, For the weld metal, the cyclic-life curves indicated the possibility of premature fatigue failures but, as al the input parameters represented a 'worst case' situation, this assessment could wel be ultra-conservative. In the rail steels at low levels, the extension of the fatigue cracks occurred by ductile striated growth. At a Kmax level of 35 MPa .J/n, cleavage facets formed initially on the surface of the fatigue fractures, and their incidence increased with Kmax until the onset of fast failure, The microstructure of the deformed rail steel exhibited cleavage facets at a slightly lower Kmaxvalue, and contained more cleavage facets at a given K level, than the microstructure of the undeformed rail steel. The average size of the cleavage facets agreed well with the pearlite nodule dimensions of 60 to 100 ILm. The microstructure of the weld metal was much coarser and contained columnar grains. At al f.K levels, the dominant fracture mode was cleavage, with small isolated regions of ductile striated fatigue cracks. The size of the cleavage facets varied from 150 to 600 ILm, and such a variation may be explained by the fact that cracking generally occurs in association with the pro-eutectoid ferite phase, and that this phase is distributed along some boundaries of prior austenite grains and the boundaries of the coarser columnar grains.

Jan 1, 1987

A Colloquium and General Meeting were held on 17th March 1971, the theme being 'Future trends in steel production'. Mr V. C. Robinson (President) was in the Chair. The Colloquium was attended by 121 delegates and was opened by the President at 10 a.m. OBITUARIES THE PRESIDENT: 'It is my sad duty to announce the death of the following: F. O. Read, Fellow, who joined the Institute in 1957 and passed away on 13th January, 1971. P. G. M. May, Member, who joined the Institute in 1969 and passed away on 10th August, 1970. R. J. J. Rademeyer, Life Fellow, who joined the Institute in 1942 and passed away on 23rd September, 1970. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments silence. CONFIRMATION OF MINUTES THE PRESIDENT: 'May we confirm the minutes of the monthly general meeting held on 21st October and 18th November, 1970, as published in the Journal'. Agreed. MEMBERSHIP THE PRESIDENT: 'I have much pleasure in announcing that the names of the undermentioned candidates, having been published in accordance with ByLaw 5.2.2, Council has elected them to membership of the Institute in the following grades: FELLOWS: Romain August Lathioor, Paolo Piga, Renato Ribacchi, Willem Frederick Jacobus Smith, Matthew Churchill, Thomas Anthony James Braithwaite, Hugh Patrick Hart, Eleanor Innocentius Muller, David Alton Smith. MEMBERS: Douglas Adendorff, Petrus Jacob du Plooy, James Valentine Grant Middleton, Karl Anders Ullerstam, Josephus Theodorus Johannes van Wyk, Frank Douglas Abbott. GRADUATES: David Mervyn Gilbart-Smith, John Philip Wilcocks Bennie, Hendrik Theunis Burger, Johann Wilhelm Coetzee, Johannes Stephanus StOols, Leon van Tonder, Brian George Harvey, John Kennedy McLean. ASSOCIATES Richard Cyril Lee Stoyell, Terrence Brian Gouws, Alister Rodney Frederick MacDonald. STUDENTS: Andries Groenewald, Christiaan Johannes Hattingh, William Hendrik Hofmeyr, Stanley Thomas Vincent. I welcome the new members to the Institute and congratulate them on their election. COLLOQUIUM The President welcomed everyone present and mentioned that this was the first of the Colloquia which are to replace the Institute's monthly meetings. He stressed that discussion at Colloquia would be completely informal and would not be recorded unless the contributor requested publication. In conclusion, he thanked the organising committee, the authors and the contributors, and introduced the author of the first paper. The following papers were presented:- 'The future development of the Iron and Steel Industry' by J. P. Coetzee (Published in the Journal March 1971). Among those who contributed to the paper were Dr Bleloch, Dr K. Gebhard, Dr Way and Professor Müller. The main point made by Dr Bleloch related to the reserves of coking coal and of coal for power generation this in country and he deduced that in South Africa we are critically short of coking coal. On the basis that 4 million tons per year of coking coal are consumed for our present steel production, over 16 million tons would be required to meet the anticipated expansion in steel output by A.D. 2000. This must be set against the grim forecast made by the Coal Advisory Board in 1967 that our national reserves of coking coal will be exhausted before A.D. 2000. This gives tremendous significance to the development work presently being carried out by Iscor on alternative methods for coke production. On the other hand the blast furnace may have to be replaced by an alternative process for the reduction of iron ores, e.g., the use of rotary kilns followed by electric arc smelting. Dr Bleloch also expressed grave forebodings about the reserves of bituminous coal, pointing out that with present methods of mining the recoverable coal in any given reserve is in general only 50 per cent of that reserve. He stated that in the past seventy years great quantities of coal have been forever placed beyond the reach of mining by being undermined by extraction of lower seams or lost by being burned. A final point made by Dr Bleloch was the fast rise in the capital investment in a fully integrated steel plant, the figure having risen in the past decade from just over R200 to R350 per ton of finished steel per annum. Dr Gebhard spoke of the direct reduction processes for iron making pointing out the difficulties of securing a high percentage of reduction and the relatively high cost of smelting in electric arc furnaces. As an alternative he suggested briquetting the high carbon sponge iron

By W. Lin, H. Endo, M. Kwasniewski, A. Kamei, M. Takahashi

Uniaxial tension tests were conducted on specimens of eleven granitic rocks which came from eastern Japan, and included a granite, four granodiorites, four tonalites and two gabbros. The axial and transversal deformability of these rocks was determined based on strain measurements using wire strain gauges. The experimental test results revealed that deformational properties of the rocks investigated varied depending on their petrographic features. However, the axial strain and the lateral strain characteristics showed a similar trend for all the rocks, i.e. the stress-strain curves were non-linear throughout the whole stress range from the initial point of loading to the point of ultimate failure. Moreover, the tangent Young's modulus and the ratio of the lateral strain to the axial strain decreased monotonously with the increasing of the axial stress. Still, the deformational properties were different for individual rocks in a quantitative sense. In particular, the difference in the lateral strains among different rocks was more distinct than that in the axial strains. For example, the Poisson's ratio at a stress level equal to 50% of the ultimate strength of a granodiorite was very low, close to zero. Furthermore, the Poisson's ratio of a tonalite was lower than that of a granodiorite, and assumed a negative value. This effect occurred because the lateral strain became positive as it changed from contraction at the initial stage of loading to extension at higher stress levels. There is no ready explanation for this phenomenon; it is believed, however, that it occurs due to microcracks pre-existing in rock materials and/or weak bonds between the adjacent mineral grains. Les essais de traction directe ont été conduits sur les échantillons de onze roches granitiques provenant de la région Est du Japon: un granit, quatre granodiorites, quatre tonalites et deux gabbros. Déformabilité axiale et transversale de ces roches s’était déterminée en utilisant des jauges extensométriques à fil. Les résultats obtenus à partir des essais montrent que la déformabilité des roches examinées varie selon leurs propriétés pétrographiques. Cependant, à partir des essais, une tendance semblable était observée dans les paramètres de la déformation axiale et la déformation latérale de toutes les roches; c'est-à-dire chaque courbe de contrainte-déformation était non-linéaire dans tout l'intervalle de contraintes à partir de l’état initial jusqu’à l’état d’une rupture finale au cours du chargement. De plus, le module tangent de Young et le rapport de la déformation latérale sur la déformation axiale a diminué de manière monotone avec l'augmentation de la contrainte axiale. Cependant, les différences quantitatives de propriétés de déformation sous traction étaient observées entre des roches individuelles. Particulièrement, la différence de déformations latérales était plus notable que celle-là de déformations axiales entre des roches différentes. Par exemple, le coéfficient de Poisson à un niveau de contrainte égal à 50 % de la résistance d'un granodiorite était très bas, près du zéro. En outre, le coéfficient de Poisson de la tonalite était inférieur que celui du granodiorite et a assumé une valeur négative. Cet effet est apporté parce que la déformation latérale est devenue positive en passant de la contraction dans l'étape de chargement initiale à l'extension sous les contraines plus hautes. Il n'y a aucune explication prête de ce phénomène; on prétend, cependant, qu'il est induit par des microfissures préexistantes dans des matériaux rocheux et/ou des joints faibles entre les grains minéraux adjacents. Einaxiale Zugversuche wurden auf Probestuecke von elf frischen, in Ostjapan vorkommenden, granitartigen Gesteinen durchgefuehrt, welche einen Granit, vier Granodiorite, vier Tonalite und zwei Gabbros umfassten. Die axiale und transversale Verformbarkeit von diesen Gesteinen wurde durch Verformungsmessungen mit Drahtdehnungsmessstreifen geklaert. Die experimentellen Versuchsergebnisse offenbarten, dass Verformbarkeitseigenschaften des untersuchten Gesteins in Abhaengigkeit von ihren petrographischen Eigenschaften variierten. Jedoch zeigten die axialen und die lateralen Spannungsdehnungslinien eine aehnliche Tendenz bei allen Gesteinen, d.h. die Verformungskurven waren nicht linear im ganzen Bereich vom Ausgangspunkt des Belastens bis zum Punkt des entgueltigen Bruchs. Ausserdem verringerten sich das tangentiale Elastizitaetsmodul und das Verhaeltnis der lateralen Verformung zur axialen Verformung monoton mit der Erhoehung der axialen Spannung. Dennoch waren die Verformbarkeitseigenschaften der einzelnen Gesteine in der quantitativen Wahrnehmung unterschiedlich. Insbesondere war der Unterschied bezueglich der lateralen Verformungen zwischen verschiedenen Gesteinen eindeutiger, als der in den axialen Verformungen. Z.B. war die Querkontraktionszahl auf einem Spannungsniveau, das 50% der Zugfestigkeit eines Granodiorits entspricht, sehr niedrig und nah an Null. Ausserdem war die Querkontraktionszahl eines Tonalits negativ und deshalb niedriger als die eines Granodiorits. Dieser Effekt trat auf, weil die laterale Verformung, als sie sich von der Kontraktion am Ausgangsstadium des Belastens bis hin zur Ausdehnung auf den hoeheren Spannungsniveaus aenderte, positiv wurde. Es gibt keine fertige Erklaerung fuer dieses Phaenomen; es wird jedoch angenommen, dass es wegen der Mikrorisse auftritt, die vorher im Gesteinsmaterial und/oder in den schwachen Bindungen zwischen den angrenzenden Mineralkoernern existieren.

Jan 1, 2003

By R. P. King

Held on the 22nd March 1972 at Kelvin House. Four papers were presented at this colloquium, which was attended by approximately 120 people. The first paper, 'Flotation Research Work at the N.I.M. research group, University of Natal on the modelling of a Flotation Process' was presented by Dr R. P. King, the leader of the N.I.M. Research Group in the Department of Chemical Engineering at the University of Natal. A discussion panel, under the chairmanship of Dr R. E. Robinson with Mr M. Dawson (PMC), Mr E. Roux (FOSKOR), and Dr B. K. Loveday (NIM), discussed the potential application of the theoretical work on flotation modelling to industrial processes, and alternative approaches to providing a way of control of flotation plants. The second paper, 'Fundamental Studies of the Flotation Process the Work of the National Institute) for Metallurgy', was presented by Dr N. P. Finkelstein. The discussion panel for this paper was under the chairmanship of Professor D. D. Howat,and had as its members Mr H. P. Carlisle (JCI), Professor D. le Roux (University of Pretoria), and Mr E. Rudolph (Anglo American Research Laboratories). A lively discussion on this paper ensued, with several contributions from the floor. After lunch, Mr S. K. de Kok, Assistant Consulting Metallurgist, Anglo Vaal, presented a paper on 'The Flotation of Copper and Zinc Sulphide from Prieska Ore'. The paper was discussed by a panel comprising Dr V. C. Lovell (NIM), Mr A. Gilbert (General Mining), and Dr D. Legge (Anglo Vaal), under the chairmanship of Dr L. Bushell. This discussion, in which many members of the audience participated, revolved around the difficulties associated with the production of copper and zinc concentrates and the lack of fundamental information on the behaviour of copper and zinc sulphides in flotation. The final presentati0n was a paper, 'The Recovery by Flotation of Cassiterite contained in Gravity Concentration Plant Tailings', presented by Mr E. B. Viljoen (Metallurgy Department, Goldfields South Africa Limited). The discussion, led by a panel consisting of Mr O. Tant (Goldfields Laboratories), Mr J. Levin (NIM), and Mr R. I. Shanks (NIM), under the chairmanship of Mr H. Cross (Goldfields South Africa Limited) referred particularly to the use of new reagents for the flotation of tin, with particular emphasis on the fundamental relationship between reagent composition and its ability to float this type of mineral.

Jan 4, 1972

By S. Wakita, K. Aoki, Y. Mito, K. Date

It is of great importance to prevent a leakage of hazardous substances from underground storage plants, because this certainly leads to a fatal disaster for human societies. Therefore, effective grouting system needs to be developed, which can inject cement grout into low-permeable rock masses. Authors have carried out a series of laboratory injection tests using a fracture model and field tests in low-permeable rock masses. In these tests, not only was the superiority of dynamic grouting confirmed, but also the relationship between grouting-efficiency and injection parameters was investigated. In this paper, the results of laboratory injection tests and field tests together with theoretical approaches to them are mentioned. L’empêchement de la fuite des substances dangereuses des galeries de stockage est un traitement très important pour protéger la société humaine contre la comtamination catastrophique. Par conséquent, un procédé d’injection efficace doit être mis au point, qui peut injecter du coulis de ciment dans le rocher ayant une perméabilité basse. Les auteurs ont effectué une série d'essais d'injection en laboratoire en utilisant un modèle de rupture et d'essais sur le terrain dans le rocher ayant une perméabilité basse. Dans ces essais, était non seulement la supériorité du l’injection dynamique confirmée, mais aussi le rapport entre l’efficacité de l’injection et les paramètres d'injection a été étudié. Dans cet article, les résultats des essais d'injection en laboratoire et des essais sur le terrain ainsi que les méthodes théoriques pour les essais sont mentionnés. Es ist wichtig, Durchsickerns gefährlicher Substanzen aus unterirdischen Lagerstellen zu verhindern, weil dies für die menschliche Gesellschaft unter Umständen zu verheerenden Unfällen führen kann. Daher muß ein effizientes VerfugesSystem entwickelt werden, welches erlaubt den Mörtelschlamm in wenig durchlässige Felsenmassen einzuspritzen. Die Autoren haben eine Serie von Laboreinspritzungsversuchen mit einem Bruchmodell und Feldversuche an wenig durchlässigen Felsenmassen durchgeführt. Diese Versuche zeigten nicht nur die Überlegenheit des dynamischen Verfugens, sondern wurde dabei auch das Verhältnis zwischen Verfugen und Leistungsfähigkeit sowie den Einspritzungparametern untersucht. In dieser Studie werden die Ergebnisse der Laboreinspritzungtests und die Feldversuche zusammen mit den entsprechenden theoretischen Ansätzen erläutert.

Jan 1, 2003