Search Documents

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

With increased emphasis on controlled blasting, which is the first and least-costly stage of comminution, ore grindability and plant throughput can be increased by 5% to 10%, and energy savings of up to 10% appear possible. Crushing and grinding efficiencies are presented for ore blasted under regular and adjusted field conditions. An economic analysis of drilling and blasting through crushing and grinding is presented, suggesting that cost savings approaching 10% may be achieved.

Jan 1, 1998

By Larry Diaz

A single stage ball mill-cyclone circuit was extensively tested for its reactions to step changes in three controllable variables: feed rate, water to cyclones, and water to the ball mill. A series of carefully designed tests are to be carried out in order to determine relationships between the various ball mill and cyclone parameters. Cyclone overflow particle size distribution is to be continuously monitored during the tests using an ultrasonic device. Other circuit variables that are to be measured and recorded are feed rate, ball mill mass flow, cyclone feed and overflow densities, cyclone feed sump level, water flows, etc. Once the circuit performance is defined, two types of grinding circuit control systems will be evaluated: (a) mass flow-based; (b) particle size- based. Results obtained by each approach in terms of feed rate and cyclone overflow size distributions are discussed. The high sensitivity of continuous particle size measurements to grinding circuit disturbances is emphasized.

Jan 1, 1971

By Malcolm D. Flavel

As indicated in the introduction to this paper, it is a sequel to that which I gave to the last annual meeting in Atlanta in march. This paper goes further into aspects of crushing and screening, primarily from the standpoint of circuit control. There has been little published by equipment manufacturers on this subject and this is the first paper on crushing circuit control to be sponsored by Allis-Chalmers corporation. By proper control over the use of crushing energy, we will be able to produce finished products from feed materials uti¬lizing minimum capital for the lowest cost of production. The subject will be discussed as follows. Firstly, we will look briefly at what we are trying to accomplish; Secondly, what is presently available in the way of technology; Thirdly, we will look at a suggested new system of control which will best fit the parameters of the normal crushing and screening operation; As a conclusion, I will summarize the advantages of the new system.

Jan 1, 1977

By V. Nasri, P. Jarast, M. Bakhshi

The Montreal metro Blue Line Extension toward the northeast consists of the construction of five new underground stations. The project includes 6 kilometers of the tunnel which will be constructed using a Tunnel Boring Machine (TBM). In line with the commitment to integrating sustainability best practices, Envision verification is pursued this project. The Envision reference framework was developed to cover all the sustainable development aspects of an infrastructure project and each phase of its life cycle (planning, design, construction, operations and maintenance, and end-of-life). As a part of this endeavor, low-carbon concrete and shotcrete mixtures are proposed for the linings of TBM and SEM tunnels as well as stations and auxiliary structures. The CO2 emission of the low-carbon concrete and shotcrete mixtures were compared with their typical mixtures and the total CO2 emissions reduction related to the tunnel lining is determined. The study is of strategic significance for achieving emission reduction in the tunnel industry.

Jun 13, 2023

By Brij M. Moudgil

Flotation was introduced in phosphate rock processing in the late twenties and since then it has been an important part of the concentration process. More than two thirds of the rock produced in Florida is upgraded by the flotation process. Since no crushing or milling steps are involved in the material preparation, the flotation plant feed is coarser than in most other mineral flotation systems. During hydraulic processing of the rock, particles in the size range of -14, +150 mesh constitute the flotation feed. This size fraction is further classified by hydraulic sizers, stationary screens and vibrating screens into a coarse (-14, +35 mesh) and a fine (-35, +150 mesh) flotation feed. The flotation techniques for concentrating the fine feed as practiced by the Florida Phosphate producers have been standardized over the years, however, methods for upgrading the coarse feed differ from plant to plant. In this paper an effort has been made to present relative merits of the techniques employed for concentrating the coarse phosphate rock..

Jan 1, 1977

By W. L. Price

The intelligent selection of wire cloth and perforated plate for screening surfaces seems a rather confusing subject to the newcomer in aggregate processing. The proper application of various screening surfaces is a complicated one and one could consider himself an expert only after many years of working with all applications. However, part of the subject matter could be simplified considerably for, the average screen user. In this paper an attempt will be made to do this, by presenting some comparative specification data along with cost figures Unfortunately, it is impossible in the limited scope of this paper to give actual service comparison records between different cloths or cloth and plate. Anyone who has considered making actual service comparisons for competing screening media is well aware of the almost insurmountable problems Their solution would form the basis for a separate paper on that subject alone. Therefore, this paper will be limited to comparative data up to the point of installation.

Jan 1, 1961

By R. J. Sweigard

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Jan 1, 1997

By Scott G. Britton

Planning is a management tool used to solve problems and provide data and decision alternatives for company growth, profitability, and direction. Strategic planning is defined as the efforts needed to accurately measure the risks of obtaining a result from future actions given a finite number of outcomes. The techniques of strategic planning are being applied more and more to underground mine design as a result of the fierce market conditions underwhich the industry is facing today, and the conditions they will likely face in the future. The objectives of strategic planning are centered on the ability of the operator or company to manuever its limited resources to the best position available under the given future scenarios. This paper briefly examines the most popular techniques for accomplishing these objectives, how these techniques fit into the current mine management decision-making, and what results to expect from these techniques in planning efficient underground mines.

Jan 1, 1985

When I wrote the Railroad portion of "Mining Engineering" magazines 94 Powder River Basin (PRB) Coal Article I described to you some definite destinations the Railroads had in mind. As with many destinations, the ones I wrote of turned out to be merely stops on the way to places that we have yet to reach. Somewhere along the way we discovered that making it better is a continuous process not just something that you can do in phases I, II, III, & IV. We always knew this I suspect, but perhaps not at the awareness level that exists in RR environments in 1997. The purpose of this article is to update the 94 article, which I could do very quickly. Everything I told you we were going to do in 94 is done, end of story! But in addition to making it a very short article it would not be telling you the things RR has done beyond what we were planning in 94 and for the future.

Jan 1, 1998

By Philip E. LaMoreaux

The development of large quantities of ground water for any major use in an area is always of environmental concern to representatives of regulatory groups, citizens, agricultural and industrial users. From these concerns, state and federal congressional representatives receive a variety of impulses from their constituents and in turn begin a series of questions upon which to-base appropriate legislative actions. The kaolin industry in Georgia is substantial to the economy and the welfare of an important segment of east-central Georgia. It uses large quantities of water for processing. This constitutes an important source of income and tax revenue. Pumping test procedures to provide an accurate and efficient dewatering scheme have been developed and carried out at a number of mines in the kaolin district of Georgia. This paper highlights one such test and is directed at an assessment of the impact of this industry on ground water supplies of an area.

Jan 1, 1983

By Allan M. Johnson

Dewatering is a major operational cost at sane mines. Under certain conditions, costs associated with water disposal may continue beyond the productive life of the mine. For mines with mineralized waters, this is of special concern. Since 1974 experience has been gained from the examination of a number of closed underground metal mines that exhibited drainage problems. It was observed in certain cases, that had appropriate steps been taken prior to closure, that the resulting drainage problems could have been largely avoided. The pre-closure steps would have involved alteration to the "plumbing system" of the mines: i.e., the drifts and crosscuts interconnecting the workings of the mine. This could have best been accomplished by the placement of bulkheads and/or selective drifting. In addition to reconfirming that hindsight is 20-20, a lesson learned from these case studies shows that a relatively simple hydrologic evaluation prior to mine closure may avoid a troublesome and costly drainage problem.

Jan 1, 1983

By S. S. Hsieh

As part of a program to address long-term needs for ensuring adequate supplies of domestic phosphate raw materials, the Tennessee Valley Authority (TVA) has conducted considerable research on dolomitic phosphate rock beneficiation. The discovery that alkyl diphosphonic acids act as phosphate mineral depressants led to the development of several processes involving a carbonate flotation step for the effective beneficiation of these problem ores. Most recently, a partial de-oiling process in which the reagent consumption is greatly reduced has been developed. The reduction is achieved because part of the initial feed is beneficiated without passing through the separate carbonate flotation step. Using this method, a phosphate product containing 30.6-30.9% P2O5 and 0.7-0.8% MgO was obtained from a Florida dolomitic phosphate pebble which contained about 23% P2O5 and 2.0% MgO. The P2O5 recovery was 80.8-86.5%.

Jan 1, 1989

By Robert W. Cope

"Mining began, in the Colstrip area in the 1920's by the Northern Pacific Railroad. The coal was used for steam locomotives until 1957, when the advent of diesel power made them obsolete. In 1959, Montana Power Company purchased the Northern Pacific properties including the mining equipment, coal leases and the town of Colstrip. Western Energy Company, a wholly owned subsidiary of Montana Power Company was formed in 1966 to manage the mining operations in Colstrip. The Rosebud Mine officially re-opened in 1968 to supply coal for Montana Power Company's J. E. Corette Plant In Billings. Since 1970, Long Construction has operated the mine equipment for Western Energy Company". The Rosebud Mine is located in Southeast Montana and supplies coal to two 350 megawatt power plants located in Colstrip and one 180 megawatt plant located in Billings. Approximately 30 percent of Western's annual production is consumed by these plants. The remaining production is shipped to the mid-west and burned by utility companies and municipalities.

Jan 1, 1981

By Douglas Ball

An underground storage field is a gas field where man, not nature, has put all or most of the gas. All but one of those in use today are in the pore spaces or "porosity" of sedimentary rocks, the most common being sandstone. The one exception, near Newcastle, England, is a gas storage in a cavern dissolved from rock salt. The tens of millions of barrels of LPG (liguified petroleum gas) now stored in salt caverns mined in shale is liquid storage, not gas storage, and in this paper I recognize the presence of these installations but do not include them in the gas storage category, Since, with the English exception, gas storages are gas fields, they can all be sorted into the categories used to describe gas fields, 95% of them once gas fields anyway, but some of the remaining 5% are the ones having the greatest effects on underground waters.

Jan 1, 1960

By C. Caceres

Fibre reinforced shotcrete in combination with other types of support systems is becoming the leading support method for underground excavations, especially those present in low quality rock masses. Sudden or rapid ground support failure can expose workers to safety hazards, damage to equipment and others resulting in production interruptions that will impact the cost of operation. Knowing the peak and post-peak strength characteristics of the support system over time are of major importance. Round Determinate Panel Testing of fiber reinforce shotcrete is the primary test used by the mining industry to determine strength characteristics; however, the tests are costly and significant manpower is required in a mine environment to build, store, handle and test the panels. For these reasons numerical modeling can result in an effective method to produce realistic results. This paper examines the strength characteristics Round Determinate Panel tests and its ultimate application in underground excavations, using Itasca?s three dimensional particle flow code (PFC3D).

Jan 1, 2010

By G. A. Gordon

For the purpose of examining a specific problem, it is important that we look at the context, to obtain an appreciation of the general area of which the particular problem forms a part. It is my task today to speak on a particular relationship between the nations of Canada and the United States of America. What is the background? Almost two hundred years ago we both belonged to a family of nations -- the British Empire. There was a serious family quarrel in 1776 and the United States left the family and set out to make its own independent way in the world. Canada, which was not as grown up as the united States, remained with the mother country, and in 1812 resisted a vigorous attempt by the United States to get it to leave home too. With the passing of the years the bitterness of that family quarrel has faded and, aside from occasional differences, we have been getting along very well ever since.

Jan 1, 1962

By Karl A. Olsson

The Glenharold Mine is a surface mine operated by Consolidation Coal Company. The mine is located approximately 90 kilometers (55 miles) northwest of Bismarck, and 3 kilometers (2 miles) southeast of Stanton in west central North Dakota. Glenharold has a nominal design capacity of 3.0 million metric tons per year (3.3 million short tons per year). With the exception of local coal sales, this production supplies fuel for Basin Electric's Leland Olds generating station, a mine mouth power plant. The mine has 175 hourly and 50 salary employees. The Glenharold reserve extends over 210 square kilometers (80 square miles). The mining area is on a dissected plateau between the broad flat Missouri River flood plain to the north and the gently rolling uplands to the south. Erosion by intermittently flowing streams has produced many narrow, steep-walled, drainage ways. Mining begins at the 6 meter (20 foot) cover line and continues to the economic recovery line.

Jan 1, 1982

By E. A. Domínguez

Kaolin deposits of Patagonia (Argentina) were formed by ?in situ? alteration of volcaniclastic rocks or by erosion, transportation, and deposition of residual clays in small basins. The mineralogy, geochemistry, grain size distribution, and specific surface area of natural and washed kaolins were studied in order to point out the relationships with the ceramic process. Primary kaolins are coarse-grained, kaolinite+quartz±halloysite, with a very low specific surface area. Sedimentary clays are either kaolinitic?smectitic and very fine-grained or kaolinitic with a coarser particle size distribution. An interdependence between mineralogy, chemistry, particle size distribution, texture, surface activity and ceramic behavior was found. Plasticity is strictly dependent on surface activity and expandable clay minerals. Slip rheology is affected by soluble salts, smectite, and tubular halloysite. Kaolinite-halloysite play an opposite role versus smectite-I/S in slip casting and tile pressing. Kaolinite and quartz are beneficial for drying behavior while expandable clay minerals increase drying sensitivity. Firing behaviour is mainly affected by minor components supplying fluxing oxides.

Jan 1, 2010

Interstate 70 running into the mountains west of Denver, CO is the main access to the state?s numerous ski areas and other tourist attractions. As such, the highway is a vital part of Colorado?s economy. Due to the mountainous terrain in which it winds, I-70 is limited to two lanes in either direction. And, during the past few decades, the volume of traffic has increased to the point where motorists encounter major delays, particularly on Friday evenings and Saturday mornings heading west from Denver, and then again on Sunday evenings heading east. In the past, those delays occurred mostly during the ski season. However, many of the mountain towns have been successful in turning their resorts into year-round vacation destinations. A good move economically, but the pressure added to I-70 has caused even greater traffic delays, sometimes to the point where some Front Range residents avoid trips to the mountains.

Jan 1, 2013

By I. L. Jennings

In most industrialized countries, the largest element of the mining industry in physical volume is that devoted to the extraction and processing of materials for use as construction aggregates. Required for all developments in industry and commerce, power and transportation, and housing and public services, their use is so widespread that possible sources are exploited throughout all geographic regions, as close as possible to the point of use. Thus, it is also the most frequently encountered form of mining throughout the world. These materials come from four main sources:- (a) Excavation of unconsolidated deposits of sand and gravel (b) Stone quarrying. (c) Processing of slags and other mineral wastes. (d) Manufacturing from clays and shales by heat fusion. The major uses are in: (a) Portland cement concrete, that most versatile of construction materials, including the many concrete products in current use. (b) Asphalt cement concrete; widely employed for paving roads, parking lots, airfields, etc. (c) Foundation materials, such as road base, granular backfills, railway ballast, etc.

Jan 1, 1968