Search Documents

By E. D. Goddard, D. S. Murphy

Acid resistance, zeta potential and ESCA (electron spectroscopy. for chemical analysis) experiments were performed on emperador marble and four calcium carbonate samples (onyx calcite, travertine calcite, Iceland spar calcite and aragonite). Six fluorine-containing reagents were used to treat the surfaces of these materials: magnesium hexafluorosilicate, zinc hexafluorosilicate, sodium fluoride, zinc fluoride, strontium fluoride and stannous fluoride. The acid resistance of treated samples proved to be much higher than that of their untreated equivalents. The isoelectric point of treated samples approaches the isoelectric point of fluorite. Also, the fluorine content, as measured by ESCA, of a marble surface treated with magnesium hexafluorosilicate is much higher than that of an untreated sample. The binding energy off of fluorine and calcium the treated marble is consistent with the formation of calcium fluoride.

Jan 1, 1994

By Oliver Gutsche

High-pressure roll mill comminution of heterogeneous multicomponent feeds was simulated with artificial limestone-quartzite mixtures using a piston-die press. The influence of heterogeneous interactions between components of the mixture on grinding path, energy utilization and energy split have been examined. Primary fractures are governed by differential fracture strength and attrition resistance of the components at heterogeneous contacts; subsequent secondary and tertiary fracture events are governed by coarse-fine interactions in the particle-bed. The weaker component is preferentially ground out of the feed size fraction and concentrates in the fines. Energy split among the components in the mixture is a function of their relative fracture strengths. It doubles for limestone and decreases by a factor of 5 for quartzite over the entire range of the mixing ratio.

Jan 1, 1995

By R. F. Al-Fariss

The phosphoric acid industry is expected to develop in Saudi Arabia in the near future. There are three main reasons for expecting this: the discovery of phosphate deposits in the Sirhan-Turayf region, the construction of phosphate fertilizer facilities of the TSP, DAP and NPK plants on the east coast of the country, and the availability of an ample amount of sulfur As a by-product from the petrochemical industries. This study is a part of the research work performed in the chemical engineering department At King Saud University to evaluate the Saudi phosphate rocks for the wet process phosphoric Acid production and to test different flotation methods for the carbonate rich phosphate rock In a laboratory scale flotation cell. Experimental results for the above tests, as well as Beneficiation by calcination, are presented.

Jan 1, 1993

By M. H. Kotze, M. J. Virnig, G. Steinbach

Earlier work at Mintek on the development of gold-selective resins culminated in a plant-manufactured batch of the first generation of Minix resin. A subsequent pilot-plant campaign at a South African gold mine identified some problems with that resin. These included lower capacity and selectivity for gold compared with the laboratory prototype, and a slow but progressive loss in capacity as the resin was eluted and reloaded cyclically. These problems were overcome by chemical modification of the resin structure. Examples of these improvements are presented. The commercialization of a new resin for a new metallurgical application presents problems, which are exacerbated by the initial lack of demand for the resin because the process is unfamiliar to the mining industry. Progress in the commercial development of Minix is discussed in this context.

Jan 1, 1993

By H. Polat, S. Chander

Relatively large amounts of hydrocarbons such as fuel oils are often needed in the flotation of low rank coals. The amount of oil can be decreased considerably by using surfactants as promoters. The reagents that are good candidates as surfactants to promote hydrophobicity can also act as emulsifying and wetting agents. Because the physical and chemical variables influence various subprocesses in different ways, their influence on the performance parameters is complex. The results of laboratory tests are presented to show that the dual role of reagents can be judiciously exploited to increase both the recovery and grade of the clean coal. The mode and order of reagent addition is critical in enhancing their efficacy as flotation promoters. The results demonstrate the benefits of proper conditioning of the pulp prior to flotation.

Jan 1, 1999

By Robert J. Timko

New methods of reducing stopping leakage have been investigated by Mine Safety Appliance Research Corporation, working under contract to the U. S. Bureau of Mines. It was found that proper construction techniques are far more important in reducing leakage than the type of sealant used, provided the sealant has sufficient adhesion and strength. Leakage could also be substantially reduced by brushing on modified mortar sealants rather than using the accepted method of trowelling them on.

Jan 1, 1982

By Richard C. Corson

Modern microprocessor systems make it possible to use several variables to anticipate changes in the process and to react with responses before upsets can be magnified by the process or by control action. Through tighter control, "insurance" can be eliminated from process set points without affecting product quality. In actual operation with a traveling grate furnace this control philosophy has produced savings of up to 20% in fuel consumption and 8% in fan power usage while producing a more consistent quality product.

Jan 1, 1982

By R. Balderrama Neder

A study consist in 20 column leach tests was performed for the "EI Arco" Copper ore deposit, located on Baja California, Mexico. The main purpose was to define the basic criteria like recovery and sulfuric acid consumption, for a commercial heap leach system design, to process the oxide Copper (Chrysocola) of the deposit. Leach parameters such as, amount of sulfuric acid in the cure solution, cure technique, particle size of the material, leach solution's flowrate application, leach solution's acid strength and height of the lifts, were evaluated to choose those parameters in which the results were the best ones for that particular design.

Jan 1, 1997

By E. Spencer

Overexposure to hazardous noise has been found in most mining sectors, with up to 100% of the surveyed workforce experiencing a noise dose over the Mine Safety and Health Administration (MSHA) permissible exposure level (PEL). As a result, miners show elevated rates of hearing impairment of 70-90% by retirement age. To help manage noise exposures, the National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software and implementation guide for use by mine management and safety personnel. The software relies on a time-motion study that profiles the worker?s daily activities. Observations about the worker?s location and tasks or other activities are recorded along with the start and end time, to determine the duration of the tasks, so they can later be matched up with the noise data. The software gives the user the option of assessing dose relative to the MSHA PEL, the Action Level or the NIOSH Recommended Exposure Limit. The software generates a variety of interactive onscreen displays showing where, when, and how the worker?s noise dose accumulated. It also can generate customizable printed reports. These outputs can be used to highlight the tasks, locations, and times that are associated with the greatest amount of the worker?s noise exposure. DOSES simplifies the record keeping and analysis associated with time-motion studies and worker noise exposures, so mine management can make engineering noise control or administrative control decisions to limit the noise over-exposure of their workers.

Jan 1, 2010

By A. A. Mathews

INTRODUCTION When Palmer King asked me to prepare a paper for this conference, it seemed quite appropriate, since I am Chairman of Subcommittee No. 4 of the U. S. National Committee on Tunneling Technology and we are presently making a detailed study of contracting practices. Before the end of this year, we expect to publish our report containing guidelines aimed at improving our contracting practices and minimizing the problems which develop therefrom. The American construction and mining industries today are glowing examples of the ingenuity of man pitting his wits against the unknown. Without the promise of rewards commensurate with the perils faced and the effort expended, it is doubtful that these industries could have reached their present state of advancement. Nevertheless, these industries are still primitive compared to many others such as aerospace and electronics. That our present contracting practices leave something to be desired is evidenced by the fact that many of our underground projects wind up with tremendous increases in estimated cost, financial disaster, and costly dispute and litigation. The situation is aggravated by the current economic uncertainty, energy crisis, and shortage of materials. At the same time, if our industries are to develop their maximum technologic potential, we must employ contracting practices which will encourage that development. Most of the contractual problems related to underground construction are associated with risk and its management. Unless all of the ramifications of this subject are understood, it will be difficult

Jan 1, 1974

By D. Boufounos

The large open pit areas of surface mining as well as the huge quantities of residues generated during the digestion of bauxite with sodium hydroxide solution to produce alumina are considered as the most important environmental problems associated with the exploitation of bauxites. Aluminum of Greece, which is the only aluminum refinery in the country, located in Agios Nicolaos, Paralia Distomou, Viotia, produces almost 680.000 tones of bauxite residue annually which is pumped through pipes from the refinery to the sea bed of Antikira gulf. In order to avoid any kind of environmental problems related to this disposal method and to reduce the total volume of bauxite residue disposed of in the environment, Aluminium of Greece investigates several alternatives for bauxite residue utilization. In this framework, it also examines the potential use of bauxite residues as a filler in abandoned mining open pits. Bauxite residues are mainly composed of fine particles of silica, aluminum, iron, calcium and titanium oxides and hydroxides. Furthermore, the material presents low hydraulic conductivity, slightly higher than the limit posed for low permeability layers by the EC landfill directive. Based on these properties the dry disposal method was selected for disposing bauxite residues in mining open pits since it has many advantages such as reduced overall disposal cost, effective use of land and minimum environmental impacts. The results obtained for this method, which is investigated at demonstration scale, are presented in this paper.

Jan 1, 2005

By Peter A. Gillett, Ian S. Clelland, J. G. S. Hynd

Today mine shaft and slope contracts include a greater amount of ancillary work such as level and pump stations, loading pockets, rotary and side dumps and connecting raises. This ancillary work requires the application of a number of construction methods often for short periods and often at short notice if the contractor is to maintain a profitable operation. In the next decade, the number of shafts that will be sunk by a boring method will outnumber those sunk by traditional methods. This will be particularly true of the deeper shafts where water problems are minimal. The increase of bored shaft work will not decrease the work completed by the shaft sinking contractor but it will change it. A greater emphasis will be placed on the speed of construction of station and other ancillary work. To meet this challenge the contractor requires full information on the ancillary work as well as the shaft work at an early date, preferably pre-bid. The two examples discussed in this paper illustrate the importance of early information. The two main factors of shaft ancillary work construction are sequence and ground support. This paper describes two examples completed recently by The Cementation Company of America Incorporated in Arizona. The first described is a Rotary Dump-Ore Pocket-Ore Pass complex and the second described is the excavation of the Main Station Level in a 2 Station-Loading Pocket-Ore Pass complex. CONSTRUCTION OF ROTARY DUMP, ORE POCKET AND PASS Introductory

Jan 1, 1976

By D. M. Kjos

Large-diameter autogenous and semiautogenous grinding mills represent the primary thrust of the expanding grinding technology. In spite of initial difficulties, large autogenous and semiautogenous mills have reached an acceptable level of technology that provides the mineral engineer with a reliable, low cost means of ore comminution. A successful milling installation begins during the design stage of the grinding mill and the plant in which it is to be installed. This is particularly true in autogenous and semiautogenous mills. Critical mill and plant design factors should be considered while the mill and installation are still only "paper." Various current liner designs will be discussed ranging from lifter bar/plate to integral types. Modes of operation such as "high-low" will be considered. Liner maintenance procedures ranging from laydown area in plant design, proper mill shutdown methods, to installation and bolt tightening complete the equation to yield optimum performance possible for any particular grinding application. The objective of this paper is to discuss trends in wear materials, designs, and operating practices, and to provide some guidelines for good practice as we move through the 1980s. We will put together concepts that relate to the designs, materials, and applications so that higher performance can be obtained by the operator for his specific application. The concepts are shown as being in series became they are dependent on each other to achieve the desired performance: designs times materials times application results in higher performance (Arnson, Parks, and Kjos, 1983).

Jan 1, 1987

By J. R. Johanson

In recent years the procedures for functionally designing bulk storage bins and hoppers have evolved from qualitative guess and try methods to a quantative method based on theory and tests of the bulk solid to be stored. This quantative method, developed and implemented by Dr.'s A. W. Jenike and J. R. Johanson as with any new design, must prove its effectiveness and validity in the actual operation of the finished equipment. How accurate are the theoretical predictions? Is it possible to extrapolate from bench size tests on a small ample of the bulk solid to the full scale bin design? Can the theoretical designs be economically translated into working hardware? In this paper the answers to these questions are discussed in light of actual bin operations.

Jan 1, 1968

Mining at Hudson Bay Mining & Smelting's (H. B. M. & S.) Snow Lake Division is now in the mature stage of the mines lives. These base metal copper-zinc mines have been operating for over 30 years. Stopes had small pillars called "crown pillars", left between them. These pillars range up to 100 meters long by 40 meters wide and 15 meters thick. H. B. M. & S. has been successful in removing these pillars through the use of cable slings, electric scoops, longhole mining and diesel LHD equipment. The different shapes and sizes of these pillars has meant that many innovative techniques have been tried in order to find acceptable economic mining methods. An overview of the different methods will be outlined.

Jan 1, 1992

By Sarkis G. Ampian

This late 1979 Bureau of Mines report presents current stocks and monthly consumption rates for Guyanese refractory bauxite (GRB), with emphasis on the impact of the GRB shortage on the refractory and downstream industries, general background material, and an evaluation of the situation resulting from the strike of Guyanese bauxite workers during the summer of 1979. A study by the Bureau indicated that industry stocks contained little more than a month's supply of GRB--30,000 calcined short tons (CST), at present consumption rates of 25,000 CST per month. The report was requested by the Federal Emergency Management Agency (FW) in response to refractory industry requests that the Government release GRB from the National Stockpile to minimize forecasted industry problems. The report traces the historical innovations in the high-alumina and/or bauxite-type refractory products industry, eventually leading up to fabrication of modern, high-quality firebrick and monolithic refractories.

Jan 1, 1980

By M. Niec

Lignite deposits in Poland occur within clastic Tertiary series at the depth suitable for opencast mining. Aboundant aquifers with the good quality waters that should be protected against contamination or depletion often accompany them. Landscape and underground water protection are the main regional environ-mental factors that limit the possibility of exploration and mining; presented on map of lignite bearing series distribution allow to delimit areas "free" for exploration and mining and areas where some limitations can be met up to no admittance of any industrial activity.

Jan 1, 1994

By D. A. Norrgran

The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980's provided a magnetic energy product an order of magnitude greater than that of conventional ferrite magnets. This has allowed the design of high-intensity magnetic circuits operating energy free and surpassing the strength and effectiveness of electromagnets. New applications and design concepts focused on the mineral and metal processing industries have evolved. This technology also led to the development of various magnetic separators specifically designed for mineral processing applications. Applications which were not previously considered are now being applied to primary mineral upgrading and recycling and secondary recovery.

Jan 1, 1993

By M. G. Ayat

Although other methods of mineral concentration have been developed over the years, gravity separation remains one of the most efficient and economical for cleaning coal. The concentrating table and the spiral separator are popular devices used for the separation of minerals by exploiting the differences in specific gravities of the product material and the gangue. While the former device has been servicing the coal industry for over 75 years, the latter seems to have not been employed extensively for coal cleaning purposes in this country. As far as coal preparation is concerned, both separatory devices seem to be most efficient for intermediate to fine size fractions. As it stands there exists a great deal of confusion amongst preparation engineers and plant managers as to whether spirals can have a place in the coal industry. If so, whether their come back is the beginning of the end for concentrating tables, or can they be employed along with concentrating tables to contribute toward more efficient cleaning processes resulting in an improvement in the overall economics of the coal preparation industry. This paper examines the efficiency of both systems for coal processing operations as well as the basic principles, operational variables, economics, advantages and disadvantages associated with each unit operation. Attempts have been made to draw conclusions and make recommendations as to which system would be more beneficial for coals of known characteristics.

Jan 1, 1986

By C. N. Bailey

Let's review the economic factors in mill design. Talking about engineering economics in mill design reminds me of an old' saying "There are several ways to handle women but nobody knows what they are." I'm sure that the same economic factors do not apply to each of our mill designs, but for the sake of emphasis, it is well to review a few of them. They are so simple that we are apt to feel they are not important. Other speakers today are talking about the engineering factors of mill design, but I'm asking the question "Have we checked the economic factors involved in these designs? Have we checked the obvious? Many great discoveries have resulted from analysis of the things that appeared to be obvious all the time. What are some of these economic factors? Perhaps the most basic one is simply the value of minerals in place if minerals have value in the ground, they have value only because many important and different considerations add up to the probability that the minerals can be mined, beneficiated and disposed of profitably. The size formation and quality of the ore body, the distance from market, and the transportation available to the market area, depreciation rates, taxes, and the ownership interests involved are but some of the factors that must dovetail into the answer of profit, an answer prerequisite to hoped-for financing.

Jan 1, 1961