Search Documents

By Jianping Sheng, Francis Otuonye

The potential for methane and coal dust explosions in underground coal mining operations has increased in recent years with the introduction of fast coal-cutting machines. Dust explosions usually follow accidental ignition of a methane pocket. The dynamics of the explosion may be strong enough to pick up and disperse coal dust deposited on mine surfaces and ignite the mixture. A self-sustaining dust explosion can then develop and propagate at large distances. Ignition of dusts can result in a fire, and this may also lead to a dust explosion if the burning dust becomes airborne. Entrainment of dust and the resulting dust concentration in the gas stream are some factors which determine the features of the subsequent explosion and flame propagation. A model of coal dust transport in the gas stream due to the initial explosion is presented. In this model, equations for the conservation of mass, momentum and energy are coupled with the convective-diffusive model of dust transport. The system of equations is solved numerically to obtain dust concentration, convective velocity and gas pressure profiles.

Jan 1, 1989

By I. Longson

Maintaining control over underground environmental conditions in the United Kingdom is increasingly dependent on the contribution of underground booster fans. Given the recent trends of higher rates of production from a fewer number of coal faces with higher levels of mechanization and higher power consumption, the effect has been to place a greater load on the mine ventilation system. This has increased the scale of potential problems that may arise should any of the main ventilation control devices not perform at the required full duty. This is particularly true for underground booster fans. Major changes occur in the main ventilation parameters on the stoppage or restart of a booster fan which results in a temporary loss of environmental control. This paper analyzes the impact of such events and details a mathematical model thar has been developed for a single-mesh circuit containing a main and a booster fan. Predictions based on this simple model are presented and discussed with particular reference to the energy changes occurring within the ventilation system immediately following a booster fan stop or restart

Jan 1, 1995

By Firoze E. Katrak, John R. H. Black, Paul R. Ammann, Michael J. Loreth, Servi. Italo S.

Germanium is produced primarily as a by product from zinc concentrates. The important sources of gallium are alumina ores (bauxites) and zinc concentrates and residues from zinc processing. In addition, gallium as well as germanium may soon be recovered from a depleted copper mine near St. George, Utah. The major uses for germanium are in semiconductors, lenses in infrared optical systems, catalysts, and gamma radiation detectors. The major markets for gallium are in light-emitting diodes, solar cells, laser diodes, integrated circuits, microwave devices, and magnetic bubble memories. CRA projects a healthy growth in the demand for both metals. However, the role of scrap metal will continue to be important over the next decade, thus decreasing the overall demand for primary gallium and primary germanium. This paper summarizes the key elements and the economics of the markets for germanium and gallium. Much of the information, such as plant-by-plant costs of production and estimates of consumption by end use for various countries is from proprietary databases of Charles River Associates.

Jan 1, 1986

By Louise H. Michaud

An interactive mine planning system that employs recent advances in 3D computer graphics capabilities and 3D geologic modelling to aid with the tasks involved in producing dragline mine plans was developed. As well as offering large potential saving in the time required to carry out the planning tasks, the system offers immediate visual feedback to the planning engineer. This can greatly aid in the conceptual understanding of complex geology and mine plans. The package incorporates the generation of a three dimensional Gridded Seam Model (GSM) as the basis for the development of the geologic database. This modelling method is capable of accurately representing rugged topography and multiple coal seams, including folding and faulting. The GSM is then integrated with an interactive graphics mine planning system in order to develop one model and one database for the generation of the mine design, the depletion of the coal resources and the movement of spoil material. The gridded structure of the model also provides the foundation on which all mine and spoil pile volumes are calculated.

Jan 1, 1992

By Ryan Lindmark, Guoxing Gu, Zhenghe Xu, Jacob H. Masllyah

Induction time is often referred to the time required to form a stable three-phase contact between a gas bubble and a flat or droplet surface in a liquid medium. It can be used to quantify the attachment process in aflotation system. Various techniques have been developed to measure this important parameter. Due to its importance in flotation systems and other processes, significant advances in refining the induction time measurement techniques have recently been made. This paper summarizes these recent advances and describes a novel method developed to monitor bubble attachment to a pendant bitumen drop or bitumen-coated flat surface. This visualization-based method offers a higher sensitivity and accuracy than the previously developed apparatuses in the induction time measurement. As an example, the induction time for oxygen bubble-bitumen attachment was measured at a fixed bubble size as a function of temperature in two different aqueous solutions. The results showed that higher process temperature is favorable for oxygen bubble-bitumen attachment and hence bitumen flotation. Addition of calcium to the aqueous solution slightly decreased induction time.

Jan 1, 2005

By Péter Siklósi, János Zámbó, Károly Solymár

It is fundamentally important to evaluate bauxites in a realistic, commercial way on the basis of the processing technology both for the supply of existing alumina plants and for the designing of new ones. The evaluation system developped by ALUTERV-FKI consists of chemical, mineralogical, texture and technological testing. The commercial value of bauxites is basically determined by their available alumina content and the caustic soda consumption required for their processing. However, their contaminants have to be taken into consideration, too. The commercial value of bauxites also depends on the processing technology and their possibly unfavourable chemical and mineralogical composition can be /at least partially/ compensated by R&D efforts. The selection of the optimum processing technology and the effects of further developing the same are demonstrated on monohydrate bauxites containing goethite and carbonates. Some of the technological solutions /desilication or deironing of bauxites, hydrothermal treatment of the digestion residue / make at the same time possible the complex processing of the bauxites, the profitable utilization of their main components.

Jan 1, 1984

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of ‘handling supplies or material, load and unload’ and ‘moving power cables.’ Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods – the mobile manipulator, the in-mine hoist, and a cable-handling system - being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

Jan 1, 2005

By C. F. Curry

In the early 1940's Humphreys Mining Company in Florida pioneered heavy mineral mining with a dredge in the United States, In 1948 Du Pont, in conjunction with Humphreys, opened their first of two mining operations recovering a titanium dioxide product in Florida. Later on in 1952 Du Pont opened their second plant, both of which used a cutterhead suction type of operation. This process is also used in heavy mineral mining in Australia and Africa. In 1957 ASARCO started prospecting in New Jersey. Test borings indicated a large deposit of ilmenite bearing heavy mineral sands had been deposited and concentrated in an area near Lakehurst in central New Jersey. Humphreys Mining Company was contacted about the possibility of mining the ASARCO New Jersey property in much the same way as Du Pont and themselves were doing in Florida. An extensive study was made to determine the economic feasibility of mining the ASARCO property. During this study, extensive test drilling and samples for a pilot plant were taken.

Jan 1, 1975

By Vitaly T. Borisovich

Mining economics courses have been taught in Europe for more than two centuries and in the United States for most of this century. They are the mineral industry's version of engineering economics offered by industrial engineering departments. In the 1930s, mineral economics first appeared in American mining schools. This subject goes beyond the deposit and the mine. It examines the economic aspects of mineral resources in general and the individual mineral industries in particular. In 1947, the first degrees in mineral economics were granted in the United States. There are mining and geological engineers who specialize in mining economics. But it has rarely become a separate degree program. Rather, in this country and several others, a graduate student in a mining department or school will include economics in his course work. Then the person writes a thesis or dissertation on a mining economics topic. One exception is found in Moscow at the Department of Geoeconomics of the Moscow Geological and Prospecting Institute (MGPI). To place this program in perspective, some background is needed on education in the Soviet Union.

Jan 1, 1991

By Todd A. Duex

The Richmond Hill Mine has recently completed a reclamation plan to mitigate Acid Rock Drainage (ARD) which was identified at the toe of the former waste rock pile in 1992. Reclamation activities began in 1994 with the removal of ARD material from the waste rock pile and placement of this material in the former pit. This material was then isolated from the near surface environment by a low permeability capping system designed to minimize water and oxygen flow into the material. The capping system consists of, from bottom to top, six inches of limestone, 18 inches of low permeability clay liner, 4 and one-half feet of thermal barrier/drain layer, and six inches of topsoil. This capping system was completed in 1995. An extensive program is in place to monitor the effectiveness of the reclamation plan, and includes measurements on moisture content movement, temperature, oxygen content, and groundwater impacts. Monitoring has been ongoing since the completion of reclamation. This monitoring plan is demonstrating the success in isolating the material from the near surface environment and minimizing the impacts to the surrounding environment.

Jan 1, 2000

By Joaquin Marti, Peter A. Cundall

This paper reports on some recent work in which several schemes were developed to model jointed rock under high stress, with particular reference to the phenomenon of "block motion" observed during dynamic loading of underground structures. Three approaches were made, corresponding to an increasing relative importance of internal block deformations as compared to rigid block movements. The first one uses distinct element method and assumes internally rigid blocks, which can break, repeatedly, whenever an empirical crack criterion is met. In the second approach each block is allowed three degrees of freedom to deform internally. The third approach, still in the development stage, permits arbitrary deformation of all blocks, which are internally decomposed into finite-difference zones and automatically rezoned during slip to preserve the calculation accuracy on joints. The last two schemes allow arbitrary constitutive relations for the intact rock, and all three schemes permit the geometrical arrangement of joints to be arbitrarily complex, in contrast to normal Lagrange, finite-difference programs, which are unsuited to model discontinua.

Jan 1, 1979

By Alexandr A. Abramov, Svetlana M. Angelova, Oleg P. Maljuk

In this paper the effect of the ratio of grinding and grindable size classes (ore lumps, particles and grains) and the guantity of intermediate size classes in the feed of the primary wet autogenous grinding "Cascade" mill is studied and the features of the influence of these factors on the mill capacity are shown. On the basis of the experimental data from Lebedinsky mineral processing plant, where magnetite guartzites are processed, a coefficient of the "total ratio of size classes" in the feed of 9x3 m "Cascade" mill was estimated. It helps to get an evaluation of the effect of ore size classes ratio in mill media on the mill capacity and to work out some ways for its optimization in closed or semiclosed technological circuites of primary autogenous grinding. The operation of the specific energy effects for some intermediate size classes, removed from the mill as circulating load, is proposed to improve its efficiency before regrinding in "Cascade" mill and decrease negative influence of such classes accumulation in the mill media.

Jan 1, 1995

By Pieter Barendsen, Olivier Dubugnon

INTRODUCTION There are three fronts on which development efforts are being concentrated to extend the application domain of Tunnel Boring Machines (TBM), which is potentially very large - Assessment of a reliable prediction method, including machine-rock interaction and geological characterisation, so that the boring system can be designed properly and the costs remain in the predicted range for each given tunnel project. - Development of lighter, more flexible and more controllable machines to be applied in shorter, deeper tunnels or roadways, such as required in mining. - Reduction of cutter and machine costs when excavating hard rocks or difficult grounds, in developing improved tool materials, cutting geometries and tunnelling systems. The above three lines of development have a common, critical requirement: to have a reliable set of design rules to optimize the machine specifications from the knowledge of rock and geological parameters and working requirements. This optimization can only be done if a model sufficiently sophisticated is made available, able to take into account the numerous factors influencing the TBM advance , and being interactive enough to achieve the optimization.

Jan 1, 1985

By R. Frenette, A. W. Mo, H. A. Hamza

Fine particles present major technical and economic problems to those who deal with solid/liquid separation processes. In the coal industry the problem is compounded by the large amounts of produced fines such as those present in Western Canadian coals. Flocculants in the form of high molecular weight water soluble polymers are commonly considered an effective solution for the enhancement of the separation process. These reagents are relatively expensive especially when considering a low-price commodity such as coal. Optimization of the use of these reagents is therefore an operational necessity. Six polymers were evaluated as to their effectiveness in flocculating a fine coal tailing. Results were compared with those for a reference flocculant, in-use at that time in the washery. It was shown that, in general, flocculants significantly improve the solid/liquid separation process. The ranking of the flocculants as to their effectiveness in settling and filtration indicated that the best flocculants for settling were not necessarily the most effective for filtration. Flocculants that showed the best filtration improvement were generally cationic and those best for settling were anionic.

Jan 1, 1988

By B. J. Arnold, F. F. Aplan

Prior laboratory work has demonstrated that much of the fine ash forming minerals entering a flotation froth are there as a result of water carryover- from the bulk contents of the flotation cell (Arnold and Aplan, 1986a). Using a bank of four 8.5 m3 (300 cu ft) Wemco flotation cells cleaning a well-liberated Lower Kittanning seam coal, test results show that the sulfur and ash content of the froth is directly related to the water content of the froth (or inversely related to the percent solids in the froth). Reagent changes that result in a watery froth produce a higher ash content in the froth. A direct comparison of laboratory and plant results show that the standard laboratory flotation test produces a product higher in sulfur and ash than that produced in the plant. Caution should be exercised when extrapolating laboratory test results to the plant situation. A method of estimating coal flotation product quality in the plant based on laboratory tests is given.

Jan 1, 1991

By P. Coleman, J. C. Kerkering, S. Iverson

A fatal accident may result when a dozer is driven over a hidden void in a coal surge pile and the dozer falls into the void, burying and suffocating the dozer operator. This type of accident was analyzed by researchers from the Spokane Research Laboratory of the National Institute for Occupational Safely and Health using inexpensive fault-tree programs that had been developed, for use on a personal computer. Fault-tree analysis is a systematic safety-analysis tool that proceeds deductively from the occurrence of an accident event to the identification of the root causes of that event. The analysis identified basic and intermediate events that led to the burial of the dozer and graphically depicted the interrelationship between the basic events as well as the intermediate events leading up to the accident. A sensitivity analysis on assigned probabilities showed which events had the greatest influence on dozer burial in a coal surge pile. Operational guidelines and engineering controls are suggested to decrease the probability of a burial event.

Jan 1, 2002

By J. E. Hoffman, Massimo Maccagni, T. J. Keefe, Marco Olper, O&apos

The problem relating to the use of insoluble anodes in acidic and highly aggressive environments has still not been definitely solved, and it is therefore a recurring subject of discussion. The fields of application in which insoluble anodes play a fundamental role are mainly in the electrolytic extraction of metals, in cathodic protection with impressed current, and in the production of oxidized halogenated salts. Based on the foregoing, B.U.S Engitec Servizi Ambientali (BESA) developed an electrode suitable for the use in the above-mentioned system. The basic component of the BESA anode is a bimetallic wire made of a copper rod (core) covered by a thin layer of valve metal, to be chosen between tantalum (Ta) and niobium (Nb). The wires, coated with suitable catalyst (PbO2, Pt or others) are inserted in a plastic frame and fixed to a current feeder by means of a screw, ensuring an optimal contact. Experimental data on the operating conditions, such as kind of electrolyte, current density, electrode potential, corrosion tests and fields of possible application, are described.

Jan 1, 1993

By G. T. Adel

Hindered-bed separators are often used in the minerals processing industry to classify particles according to size and density. A new technology, known as the Eriez CrossFlow, was recently developed to overcome some of the limitations associated with hydraulic separators. The innovative feature of this unit is a novel feed presentation system that improves separation efficiency and capacity. In the present work, a detailed process engineering evaluation was conducted to determine the basis for the improved performance of this unit. The evaluation included controlled separation tests using well-characterized feeds, particle and liquid tracer experiments and mathematical modeling studies. Data obtained from this work show that the new separator is capable of maintaining good separation efficiencies at higher solid feed rates than traditional designs due to improved hydrodynamics in the separation zone. This paper reviews the operating principle of the Eriez CrossFlow separator, discusses the results of the tracer experiments and modeling studies and presents test data obtained from recent laboratory and plant trials. Key words: Size classification, CrossFlow separator, Hindered-bed separator, Hydraulic separator

Jan 1, 2003

By Arafat Ghosheh, Yousuf Abu-Rish, Darwish Amara, Mohammed Baderkhan

The Jordan Phosphate Mines Company is one of the world's major phosphate rock and phosphatic fertilizers producers (the second largest phosphate rock exporter), with ore reserves exceeding 2 billion tonnes, mainly located in the Eshidiya area. The Eshidiya phosphate deposits, 120 km north-east of Aqaba, are of sedimentary origin (as are all phosphate ore in Jordan). Three exploitable beds (Al, A2, and A3) with variable content of P205, CaO, SiO2, etc., are processed in order to produce 68-70,73-75, and 75-77% TCP grades. The A3 bed, which is characterized as the most siliceous containing 40-48% TCP, requires physical beneficiation using wet scrubbing, screening, and desliming by hydrocylone, followed by anionic conventional flotation to achieve 75- 77% TCP grade. For the last 15 years extensive laboratory and pilot tests (including physical, chemical, and mineralogical studies) were carried out. After operating the industrial plant, certain modifications were deemed necessary to adjust the operational parameters and the final flowsheet, which was followed to obtain the targeted quantity and quality of concentrate.

Jan 1, 1999

By A. R. Wagner, E. Berkman

The use of high-resolution seismic surveys in coal exploration and mine development is becoming established as a standard technique in the industry. Their most significant contribution is in the effectiveness of reducing the number of core holes needed to understand the complex geological nature of coal by identifying geologic faults and mapping coal seam continuity and relative coal thickness. With these goals in mind, a high-resolution seismic survey was conducted in 1980 in the Wasatch Plateau coalfield of Utah. As a result of the success of this initial survey, numerous additional surveys have been performed over the past six years.. The interpretations of these subsequent surveys have led to the location of faults, fluvial channel sandstones, and coal thickness trends. This paper presents a review of high-resolution seismic technology as applied to coal exploration followed by three case histories, two of which illustrate the utility of the technique related to coal thickness determination and faulting and one that serves as an example of pitfalls in interpretation.

Jan 1, 1987