Search Documents

By A. B. Seal, C. J. Bise

Excessive noise has long been a hazard in the coal-mining industry. Studies conducted during the mid-1970s and mid-1990s consistently show that hearing loss within the mining industry persists, in spite of regulatory requirements and sampling technology advances. When the U.S. Mine Safety and Health Administration's new health standards to protect miners from hearing loss took effect in September 2000, the potential developed to reevaluate sampling approaches with regard to noise-source hazards, such as task-based methods. This paper describes results from a Pennsylvania State University research project now being conducted at an underground coal mine. Each occupation was reviewed, and a list of tasks or processes performed by each was generated. Traditional personal noise dosimetry, static sound pressure levels and equipment sound mappings have been performed. Job tasks indicating the greatest levels of daily noise exposure and contributions to noise dose have been identified and will be discussed.

Jan 1, 2003

By Joseph A. Dos Santos

The Expanded Conveyor Technology, a rationalization of the conventional conveyor technology, allows us to apply the theory and principles beyond the current (perceived) limits. This was first prompted by the writer's advancements in Sandwich Belt High Angle Conveyors. The introduction defines the Expanded Conveyor Technology and outlines the range of applicability for the wide variations in conventional and non-conventional conveyors. The writing deals with the theory and design of sandwich-belt, high-angle conveyors in the context of the Expanded Conveyor Technology, including the equations of friction, hugging pressure and the continuity of hugging principle; curvature constraints and criteria for tension, curvature, trough, and belt construction; and drive and tension analysis, load sharing and traction, including "derived load equivalents."

Jan 1, 2000

By M. Beus, S. Stewart, S. Iverson

Recent ore pass failures have underlined the need for improved designs, standards, structural monitoring methods and better hang-up prevention and removal techniques. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating methods to improve safety during the transport of ore in ore passes. Design criteria and hang-up prevention and remediation strategies involve studies of the effects of static and dynamic ore and waste-rock loads on chutes, walls, gates and support structures. Particle flow analysis methods were used to simulate the response of various ore pass designs to a wide range of ore loading conditions. A full-scale mockup of actual ore pass and chute assemblies was duplicated and tested for load response. Data from a particle flow code and the mock-ups were compared Loads on an active ore pass chute were measured

Jan 1, 2000

By S. K. Kawatra, K. J. Shoop

An analysis of an iron-ore processing plant showed that its performance was affected by seasonal temperature variations, resulting in reduced grinding efficiency during the winter months. Laboratory and pilot plant studies were conducted to determine the cause of the observed loss of efficiency at lower temperatures. Two types of experiments were performed: drop tests and wet grinding tests. Drop testing was performed to determine the effect of brittleness and frozen pore water on the breakage characteristics of the ore. The wet grinding tests were divided into laboratory tumble tests and pilot-plant tests. The combined results of drop testing and wet grinding were used to make predictions on the performance of plant-scale autogenous grinding. From the drop tests, it was determined that dry iron ore, basalt and sandstone did not change in brittleness over the temperature range studied (-25º to 25ºC). However, when the rocks were water-saturated, the highly porous sandstone became considerably more fracture-resistant upon freezing, due to "grouting" of the pores and preexisting cracks by ice. This effect was not seen for either the iron ore or the basalt, because they were considerably less porous than the sandstone. Tumble tests on both laboratory and pilot scales showed that both the addition of fines to the test charge and a reduction in temperature caused a decrease in the amount of new fines produced. This reduced fines production was the result of increased slurry viscosity when either the fines content increased or the temperature decreased.

Jan 1, 1998

By B. J. Arnold, B. W. Parker

Rosebud Mining Company added a classifying cyclone/spiral concentrator circuit addition to its McVille Preparation Plant, Freeport, PA, in mid-2002. This paper will describe the plant addition, which was implemented fully by plant staff, and review improvements in cleaning plant performance and economics.

Jan 1, 2003

By M. T. Holroyd

Digital computer applications to minerals exploration remained largely an experimental alternative to manual techniques until well into the 1960's. Due to the high cost of computer time, and the lack of digital data and appropriate software, the most favoured applications in the early days were computationally intense tasks - those which produced the most results with the least demands for programing and data input, e.g. forward modeling. When large digitisers and plotters became affordable, the computer took over simple labour intensive tasks such as data transcription, and when software caught up, more complex tasks such as contouring. Digital data acquisition systems and superminicomputers made total computerisation of geophysical compilation and cartography possible and affordable. Applications continued to develop into areas of much greater logical complexity. Software, the new labour intensive process, still lagged behind. The microcomputer made computer applications potentially available everywhere to everyone. Desk-top micros as powerful as the minis of ten years ago can take on any geophysical exploration task currently done by computer - when the software becomes available.

Jan 1, 1989

By David Sainsbury, Bevan Thompson, Yuejun Cai

The practice of placing loose rockfill as passive support in open stoping voids, of narrow vein mineral deposits, lends itself to the sterilisation of substantial mining reserves in the requirement for regional crown/sill pillars. Significant benefits are to be gained by the Australian mining industry via the development of improved guidelines for the extraction of such sterilised mine pillars. The application of selectively injecting specifically developed ettringite (calcium sulphoaluminate hydrate) type cement grout into loose rockfill, enables an artificial pillar to stabilise the surrounding rockmass and prevent the caving of loose rockfill from the previously backfilled void during extraction of remnant crowdsill pillars. This paper presents the results of laboratory testing used to reduce the technical risks associated with the design of cemented rockfill pillars. A laboratory testing program was devised to investigate the critical parameters influencing the performance of a stabilised rockfill matrix, along with the critical parameters influencing the interpretation of laboratory test samples. The factors investigated include; sample size and shape, particle size distribution, curing time, water quality, cement : water ratio and the confinement effect.

Jan 1, 2001

By J. H. Tylczak, R. Blickensderfer

Impact and abrasion properties of various commercial US grinding halls were evaluated and compared by the Bureau of Mines, US Department of the Interior. Laboratory tests were conducted on balls obtained from eight major US manufacturers. The halls included forged steel, cast steel, and alloyed white cast iron and were subjected to repeated impacts until they broke or until 300,000 impacts were exceeded. Pin abrasion tests also were conducted. The results showed wide differences in impact lives, ranging from a few thousand to over 500,000 impacts. The life of inferior commercial halls was increased five to six times by a laboratory tempering heat treatment. For halls that did not break, the major impact wear mode was spalling and ranged from an average rate of 0.28 to 4.46 mg per impact. The softest halls (steel) had excellent impact resistance but low abrasion resistance. The abrasion resistance of the steel halls generally increased with hardness. The alloyed white cast irons had about twice the abrasion resistance of the steel halls. Users should become aware of the wide variations among commercial halls, and ball manufacturers should be aware that their product can he improved.

Jan 1, 1990

By H. Nazeri, T. G. Rozgonyi

Many industries when volumes of the solid materials are large invariably relay upon the gravity to induce solids to flow out of storage, through channels and reactors. In mining industry ore pass’s requirements to less energy (only gravity) have made them very popular both in underground and open pit mines. This paper discusses the major findings of research on 2D Discrete Element Method simulation of gravity flow of ore in ore passes. Results show that ore characteristics, ore pass configuration can significantly affect loads (static, dynamic) on the gate assembly and creation of hang-ups.

Jan 1, 2003

By T. Negeri, Y. Breau, M. Plante, A. Orumwense

As part of a joint project on fine particle processing, sponsored by the Consortium de Recherche Minérale (COREM), Natural Resources Canada (NRCan) and Hydro-Quebec, two flotation plant circuits were sampled to identify and quantify the causes of mineral losses within several particle size ranges. Size distributions, size-by-size assays and global chemical assays (Cu, Zn, Fe, S) were determined for the major streams. Size distributions were measured in 13 classes by sieving, cyclo sizing (-45 µm), and laser beam diffraction analysis. BILMAT, a material balance computation software package, was used to optimise the sampling, to estimate the unmeasured variables, and to assess and improve the quality of the information generated. The methodology has been extended to correct cyclo sizer data and reduce discontinuities of up to 20% at the transition from sieves to cyclo sizer. The paper describes the methodology and the main conclusions emerging from material inventory of the flow sheets.

Jan 1, 2003

By Arthur R. MacPherson

Este capítulo revisa las etapas que deben seguirse desde el momento de considerar la molienda autógena en el desarrollo de un nuevo depósito de mineral o en la expansión de una planta existente, hasta la compra de un molino autógeno. En este caso el término autógeno incluye: semi-autógeno, molinos de pebbles secundarios y molino de bolos (trozos), así como los sistemas de molienda autógena total. También se han incluido las alternativas por vía húmeda y seca. Antes de programar el ensayo debe decidirse cuantas muestras brutas son requeridas para calcular propiamente las posibilidades de molienda autógena del depósito. También ha de tomarse la decisión, de como y donde deben tomarse las muestras, por ejemplo: planta piloto situada en el sitio de localización de la planta o en otro lugar establecido; molienda en húmedo y/o en seco....etc. En el mismo programa del ensayo se obtendrán ciertos datos fundamentales. Los ensayos deberán incluir un trabajo suficiente. para determinar cuál de las moliendas, totalmente autógena o semi-autógena, debe utilizarse; y qué tipo produce la máxima eficacia en la potencia consumida. También, los otros datos pertinentes deben ser recolectados, como por ejemplo: potencias, tonelajes, alimentación, carga, tamaño del producto, carga circulante, etc. Si es necesaria una molienda secundaria para obtener el tamano final, la decisión de qué molienda debe emplearse (molino de pebbles o molino de bolas) puede requerirse un ensayo de trabajo adicional. Finalmente, la concentración del mineral puede jugar un papel importante en la selección del circuito y debería ser una parte del ensayo final una vez que se ha establecido la molienda. Para determinar qué tipo de molinos pueden satisfacer los requerimientos establecidos por la planta piloto, debe tomarse una escala para ciertos datos como: potencia del molino, consumo de acero, simple o doble etapa de molienda, tipo de molino secundario. Para asegurar un posterior entendimiento del depósito de mineral y sus características de molienda, deberán efectuarse algunos trabajos adicionales a pequena escala utilizando pequeñas muestras y molinos para producir unos datos comparables de molienda. También, algunos ensayos tales como medio de molienda óptimo, e índice de trabajo, deberán ser completados.

Jan 1, 1982

By Alwyn Protheroe, Steve Smith, Herbert Jr. Gibson

In September of 2000, Cowin and Company, Inc., contracted with Paramont Coal Corporation to construct a large decline approximately 820 m (2,700 feet) in overall length at a grade of 8 degrees to the Lower Banner Coal Seam. This paper will discuss the methods used by the contractor and owner to overcome the unique problems required to construct this tunnel in a coal mine environment. The problems include, initial design considerations, equipment selection, ventilation, ground control, control of water in?ows, and placement of concrete.

Jan 1, 2003

By D. C. Panigrahi

The paper presents the application of Object Oriented Programming approach for the development of a network simulation model based on nodal pressure method using linearised flow equations. The convergence and computational efficiency of the algorithm have been investigated. Finally the paper re- ports the validation of this algorithm in actual field conditions.

Jan 1, 1996

By Dr. -Ing. Karlheinz Timtner

This paper deals with the complicated and often misunderstood relationship between torsional windup, load sharing and peak torques in conveyor backstops. The principals apply in low speed, intermediate speed or high speed applications. Once the controlling factors are understood, a reasonable approach to selection procedures can be achieved.

Jan 1, 1996

By Howard R. Postovit, Bonnie C. Postovit

Raptors are birds of prey. In recent years, these birds have become highly regarded and have been given protection under various state and federal statutes. Surface coal mining can have both negative and positive impacts on raptors. Mitigation strategies and enhancement techniques can be implemented to alleviate negative impacts. The success of habitat reclamation will determine the long-range impact of mining on raptors.

Jan 1, 1989

By J. A. Herbst, L. B. Hales, R. A. Ynchausti

Industrial application, theoretical discussion and technical research programs continue to stimulate acceptance of column flotation. Numerous authors have published model, parameter and application studies discussing advantages and problems which are associated with this minerals processing technique. This paper dispells the myth of the self-controlling column while focusing on the problems and opportunities which are inherent in the computer control of a column flotation cell.

Jan 1, 1988

By Walter E. McCulloch

Installation of flash flotation in the copper concentrator of Freeport Indonesia in late 1986 and 1987 increased gold recovery by about 13%, while also increasing concentrator throughput. Copper recovery remained essentially the same. Flash flotation has since been included in a recently completed mill throughput expansion to 32,000 t/d (35,300 stpd) as well as in a current expansion to 52,000 t/d (57,300 stpd).

Jan 1, 1991

By Jerry L. Hodgson

This paper presents an application case history of the planning methods used for developing, costing and scheduling an underground hydro- electric pumped storage facility in weak rock. This method covers the system configuration, excavation methods and costs, initial support systems and final lining systems. This study was performed by the Omaha District, Corps of Engineers for the proposed Gregory County Hydro- electric Pumped Storage Project, and presents a synopsis and the results of the studies performed.

Jan 1, 1986

By Patrick R. Taylor

This paper presents a fundamental study of the thermodynamic and kinetic effects of copper and iron on gold-cyanide leaching. It quantifies the solubilities of the impurities, complex formation, and kinetic effects. The necessity of solution recycle, to meet environmental standards, requires that fundamental information be generated to characterize behavior and allow the identification of treatment methods. Mathematical descriptions of both solubilities and kinetics will be presented

Jan 1, 1983

By Kal V. S. Sastry

Mathematical and expert system models are being used extensively for mineral process engineering; nevertheless, standardized methodologies for their computer implementation do not exist. In meeting this need, this paper introduces the concept of a process software model, or more specifically an object-oriented software model, and presents a detailed methodology for its development involving software model specification and development. These software models provide a formal basis for the subsequent design and construction of software objects corresponding to the real world process objects.

Jan 1, 1995