Search Documents

By A. Marabini, G. Belardi, N. Sheau, F. Veglio

The present paper deals with the modelling of a Multi-gravity separator in the treatment of chromite fines. A first screening study was carried out by 2" full-factorial experiments in order to check the main effects and interactions among the investigated factors: shake frequency, shake amplitude, tilt angle and washwater flowrate were taken in consideration in the study. Two size fractions were employed in the experimental tests. Successively, considering the factor with larger influence on the Cr203 and SiO2 grade and Cr203 recovery in the concentrate, a further improvement of the experimental design was performed to determine empirical models to describe the behaviour of the MGS in the mineral treatment. The results show how intrinsic interaction among the factors take place, highlighting that an optimization study must be carried out considering all the MGS setting parameters.

Jan 1, 1995

By Ryan Lemmon

Belt turnovers are commonly used in conveyors to rotate the belt so that the clean side of the belt contacts the return idlers. The belt turnover length has traditionally been sized on only the twisting stresses. However, belt turnovers are also subjected to bending stresses due to the weight of the belt. Although bending stresses have in the past been ignored, these stresses are significant and should not be neglected. This paper quantifies and presents a method for calculated twisting and bending stresses and also the belt sag.

Jan 1, 2002

By S. W. Clark, R. Meglen

A seismic refraction survey of selected environs of Brewster Phosphate's Lonesome mine near Bradley, FL identified various layers of overburden, minable matrix (ore body) and basement (i.e., bedrock) that correlated with core logs. Bivariate correlation procedures determined that statistical relations existed between mining parameters and seismic velocities. For instance, a correlation of approximately -0.6 was inferred between P wave velocity and ore grade.

Jan 1, 1990

By Lynn B. Hales, Randy A. Ynchausti

Because of the high economic value associated with small improvements in the operating performance of mineral processing plants, innovations in instrumentation, stabilization and expert control systems have been an ever-present part of the landscape in plants throughout the world since the I 960s. Expert control systems are computer programs that continuously monitor plant conditions; contain "expert knowledge" concerning the process, equipment and operational knowledge; and make timely recommendations for new process set points or even directly change the process set points to achieve desired management goals. Early rudimentary expert control systems first appeared in the early 1970s. They have grown from small, experimental but ambitious projects in which single unit operations were controlled to plant-wide systems that include technologies used in the U.S. space shuttle program. Experiences and results of applying these systems throughout the world will be explained discussed and analyzed. Typical results will be outlined and the use of expert control in the future will be projected.

Jan 1, 2000

By Paul M. Godlewski, Gerry Millar, Harvey W. Parker

Recently, over 70 railroad tunnels in the western USA have been enlarged and rehabilitated "live track," utilizing modern excavation and lining methods, in most cases to clear the larger double-stack container cars. This paper presents the general conditions of the tunnels and the technical aspects and costs of the rehabilitation of approximately 40 kilometers of tunnels, which range in length from a few hundred meters to 13 kilometers. Concrete-lined tunnels were rehabilitated by grouting and rock bolting, while unlined or timber-supported tunnels were relined with shotcrete and rock bolts. High output lining methods were required because of limited track time. Enlargement has been accomplished primarily by carving notches out of the concrete linings with a roadheader, or occasionally with saws. Unlined tunnels were enlarged by drill-and-blast or roadheader excavation.

Jan 1, 1991

By C. E. Jordan, B. J. Scheiner

The Bureau of Mines has developed a continuous ultrasonic flotation cell for the recovery of Florida phosphate ore. Within a small mixing chamber near the bottom of the flotation cell, an ultrasonic probe agitates an injected mixture of air, water, and phosphate ore and breaks the air into fine bubbles. Phosphate particles are preferentially attached to these fine bubbles and floated in the main chamber of the flotation cell. Over 94 pct of the phosphate was recovered, resulting in a 30 pct P205 concentrate. The ultrasonic energy consumption was less than 7 kW.h/mt of phosphate ore.

Jan 1, 1989

By Arthur P. Chaves, Lauro S. Norbert Costa, Adão B. Da Luz

A series of bench-scale bleaching tests have been carried out on kaolin samples from the Rio Capim area( northern Brazil) at CETEM/CNPq. The whole sample has been homogenized and submitted to particle size separation, when the + 44 µm fraction has been discarded, prior to being bleached. The main objective of this series of tests has been to evaluate the possible effects of interactions among variables which are believed to play important roles in the bleaching operation on the efficiency of the process itself in terms of the brightness achieved in the final product The tests have been planned according to a classical four-variable, two-level factorial technique. The chosen variables have been the pH, sodium dithionite addition, aluminium sulphate addition and bleaching time. The study has shown that, apart of time, all other three variables are significant. None of the interactions among them have shown to be of significance. Brightness numbers close to 88 have been obtained in the products, which represents an improvement, since brightness for the non-bleached - 44 µm Rio Capim kaolin sample averages 83.

Jan 1, 1995

By A. D. Agate

In developing nations, novel mineral processing methods like bacterial leaching are gaining prominence. The principles and practices for isolation and preservation of cultures used in bacterial leaching are discussed with special reference to cultures used in leaching copper from Indian ores. In all, 145 potentially useful microorganisms such as iron- and sulfur-oxidizing bacteria were isolated from various ecosystems of the copper mining areas in the country. The major organisms isolated by enrichment culture technique belonged to T. ferrooxidans and T. thiooxidans species. In addition, thermophilic cultures like Sulfolobus sp. and thermophilic thiobacilli were also isolated. The process of copper leaching was scaled up to the 300-kg level in PVC columns. Since the preservation of efficient cultures in active state was vitally important, a new method was devised that preserved the activity of thiobacilli for a period of more than two years. The novel method of storage in sterile chalcopyrite ore at 8°C can be considered an important advance.

Jan 1, 1987

By W. J. Dolinar, S. P. Sandoval

The US Bureau of Mines (USBM) implemented the Fe2+/ Fe3+-SO2 anode reaction in a Cu-electrowinning cell with full-size electrodes. Electrowinning was conducted using industrial electrolyte at 258 A/ m2 (24 A/ft2) and 40°C. Manifold injection of electrolyte provided circulation between the electrodes. Five-day operation using an optimized manifold gave an average cell voltage of 0.94 V at 89% current efficiency, which amounted to an energy savings of 2.82 MJ/kg (0.355 kW-hr/lb), compared to conventional electrowinning. Acid milling 5was completely eliminated, and the SO2 concentration 23 cm (9 in.) above the cell averaged 0.06 ppm.

Jan 1, 1996

By R. H. King, R. E. Cameron

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. This paper focuses on the KRS Algorithms that extract key information from lists of time-study type event sequences. Because a static system cannot operate effectively in a dynamic mining environment, we are prototyping an index- based technique that allows the system to adapt itself to this dynamic environment.

Jan 1, 1991

By Jerome P. Downey

Treatment of tungsten ore at Anschutz Mining Company's Chicote Grande (Bolivia) operation results in a relatively high grade arsenopyrite byproduct stream. Laboratory and miniplant testwork have been performed at Colorado School of Mines Research Institute to examine the technical feasibility of recovering a marketable arsenic product fr an this source. Process selection was constrained by the remote location of the millsite, which demands an uncomplicated, low maintenance operation. As a result of the research effort, a two-stage roasting/condensing process was developed, featuring the use of an indirect heating method. Arsenic was efficiently extracted and the arsenic trioxide (As203) product consistently exceeded the industrial purity specification of 99.5%. Key process parameters have been secured for extrapolation of the process to pilot or small commercial scale.

Jan 1, 1985

By Steven R. Wardwell, Gerald G. Stokes

INTRODUCTION A compaction grouting program to control ground loss, and to minimize surface settlement, was developed for the West Tunnel of the Phoenix Storm Drain Tunnels. The West Tunnel was 4,200 m long, 7.56 m in excavated diameter, and was excavated with shallow cover through the central Phoenix business district. The tunnel could not have been successfully excavated without the compaction grouting program. HISTORY After heated political debate over a ten year period, the Arizona Department of Transportation (ADOT) was granted approval to build the Papago Freeway, an extension of Interstate 10, through central Phoenix. To comply with environmental constraints, a portion of the Freeway was depressed, requiring an excavation 10 meters in depth, thus intersecting surface run-off from the northern section of Phoenix. This required that ADOT and Project Design Consultant, Howard, Needles, Tammen & Bergendoff (HNTB) design a drain system to collect run-off and transport it approximately 4 kilometers to the Salt River through the City of Phoenix. Tunnels were chosen for the main discharge conduits because depth and location of the system made cut and cover construction impractical. A contract for construction of the tunnels was awarded to Shank-Artukovich-Ohbayashi (S-A-O) on May 24, 1984.

Jan 1, 1987

By F. M. Doyle, S. M. El-Raghy, M. F. El-Demerdash, E. Peters

The Activity Distribution Diagrams (ADD) developed by the authors are computed for Cu-S-H2O and Mo-S-H2O systems. The distributions of metal and sulfur between all species are estimated against pH at different potential levels. Both M-H2O and S-H2O distributions are compared to the M-S-H2O distributions to estimate the changes occurring due to the presence of sulfur. The method of computation follows the Activity Term Criterion, taking into consideration the multi-equilibrium interrelations and conservation of mass. Results are analyzed in terms of dividing a distribution curve into three basic segments. These segments are formation, stability, and dissolution.

Jan 1, 1993

By Helen Joyce, Larry Twidwell, Jay McCloskey, Eric Dahlgren, Andy Hadden

The reduction of dissolved selenium oxyanions from mine wastewater utilizing an elemental iron cementation technology on been studied on a laboratory scale at Montana Tech of The University of Montana and on a pilot scale at MSE-Technology Applications as a water treatment process potentially capable of removing dissolved selenium to GO WL. Laboratory and pilot scale studies using elemental iron have demonstrated effective removal of dissolved selenium. Enhanced selenium reduction rates have been demonstrated when galvanically coupled iron/copper and iron/ nickel are utilized. The laboratory and pilot scale results are presented and discussed.

Jan 1, 2005

By Ch. Arvanitidis

This paper presents the design solution for an actual case of settlement tanks, for a wastewater treatment plant under construction, actually founded on swelling clay (the nature of which had not been appreciated beforehand) and suffering considerable damage as a result. Two points of interest prompted the use of a numerical model as an alternative approach to the traditional method of analysis: First, the desire to compare the in situ measured deformation and displacement of the tanks with the figures calculated by the numerical model. Second the need to check the validity of the suggested solution as a remedy, i.e. the replacement of a certain thickness of clay by graded material.

Jan 1, 2005

By G. P. Brahmaprakash, K. A. Natarajan, N. Jyothi, K. N. Sudha

Some important electrochemical aspects involved in the bioleaching of mixed sulfides have been discussed with reference to selective sphalerite dissolution from different binary mineral combinations. Combination potentials and galvanic currents were measured in different binary combinations of sphalerite with other minerals such as galena, chalcopyrite and pyrite in order to under- stand the electrochemical dissolution behaviour of sphalerite when coupled with other minerals. The effect of applied DC potential was also studied with reference to selective sphalerite dissolution from a binary mineral mixture. An application of a potential of -500 mV (vs SCE) was found to enhance bacterial growth as well as selective sphalerite dissolution. Factors influencing bioleaching of sphalerite under a negative applied potential are discussed.

Jan 1, 1989

By R. L. Pozzo, I. Iwasaki

A previous investigation showed that corrosion currents estimated from polarization curves for the pyrrhotite-grinding media system under abrasion correlated well with corrosion currents estimated from marked ball wear test data by applying Faraday's law. Freshly abraded metal debris were magnetically attracted to pyrrhotite and lowered the rest potentials of the mineral particles, thereby affecting the corrosive wear. The investigation was extended to explore the interactions between a non- magnetic sulfide mineral, pyrite, and abraded metal debris and their effects on the corrosive wear mechanism. The electrochemical behavior of a three-

Jan 1, 1988

By V Leus, J. Kallioinen

The large size of the modern flotation cells and the high product flow rate from them has increased the importance of optimal flotation of all the particle sizes and of process control. By treating all the subprocesses of flotation separately a new family of flotation cells and a new concept of optimizing the flotation of coarse and fine particles in separate units but in the same row of flotation cells has been developed. The paper discusses the possibility to enhance coarse particle flotation by varying the froth residence time. A function has been developed between the residence time of the froth, air rate and the froth removal rate of coarse apatite particles. The response of apatite flotation to different control variables has been studied and modelled. The results show that the BPL assay response depends not only on the control variable used but also on the feed assay to the cell. There exists an feed assay dependent region within which the froth assay can be controlled by using the froth residence time as the control variable. These regions can be used to tune a rougher-multistep cleaner circuit to optimal.

Jan 1, 1993

By S. Zaman, John Bulter, M. E. Defoe, Franklin T. Davis

This section deals with the carbon minerals and materials: graphite, tar sands, gilsonite, and diamond. as well as sulfur and the sulfides of mercury, arsenic, antimony, and bismuth. Table I contains the production figures for each of these commodities in the United States and in the world. Specifications for concentrates are also summarized as are prices for concentrates at the time the section was written. In each chapter an attempt has teen made to describe the more common commercial mineral involved with the commodity, the processes used to recover and concentrate the minerals, as well as geographical areas where these processes are utilized.

Jan 1, 1985

By Werner Stahl, Karsten Keller

Vibration screens are commonly used not only in classifying bulk material but also in dewatering it. The lack of a comprehensive physical theory of dewatering often leads to difficulties in the design and operation of the vibration screens. Firstly, the dewatering of bulk material will be shown, based on a physical model. Because of the oscillatory motion of the liquid in the bulk, the inertial force of the accelerated liquid and the dripping of water out of the bulk or screen must be taken into special consideration. The physical model put forward shows the effect of the various operations parameters of dewatering screens. The comparison between dewatering theory and practice will be shown by measurements using coal, limestone, etc. Dewatering measurements, which have been conducted on a vibration screen, demonstrate that different vibration frequencies and rates of acceleration lead to different residual moistures. Finally, the possibilities of improving vibration dewatering will be described.

Jan 1, 1995