Search Documents

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, MSHA began requiring the use of continuous personal dust monitors (cPDMs) to monitor and measure respirable mine dust exposures to underground coal miners. After the cPDM’s implementation, mine operators discovered that it interfered with proximity detection systems (PDSs), thus exposing miners to potential striking and pinning hazards from continuous mining machines. NIOSH was sought out by MSHA and mining industry stakeholders to determine how the cPDM and PDS interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments, and conducted lab evaluations. Some interferences were observed to be caused by electromagnetic interference (EMI) from the cPDM. Results showed that there was no significant interference when the cPDM and the miner-wearable component of the PDS were separated by distances of 6 inches or greater. In this study, the cPDM and PAD needed to be at least 6 inches apart in order for them to be used simultaneously and reduce interference potential. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis such as coal dust exposure, high noise levels, roof and rib falls, the potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 40 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (1,2). Proximity detection systems (PDSs) are designed to alarm miners and stop machine motion in order to protect miners from being struck, pinned or crushed by CMMs(3). Currently, MSHA-approved PDSs, installed on CMMs, are based on the principle of magnetic flux density (B-field) (4,5). The system generates a magnetic field around a CMM and determines the relative distance a miner is from the CMM based on a detected magnetic flux density. A PDS typically consists of multiple magnetic field generators mounted at different places around the CMM, and personal alarm devices (PADs), which are worn by the miners to detect the magnetic flux density. When a miner, wearing a PAD, gets closer to the machine, the PAD detects a stronger magnetic field from the generators and detects a weaker magnetic field when a miner moves away from the machine. The magnetic field generators installed on CMMs typically produce modulated magnetic wave signals at frequencies between 10 kHz and 120 kHz. The magnetic fields are measured by three small magnetic coil antennas mounted on orthogonal axes inside of the PAD worn by the miner. According to Faraday’s Law, the changing magnetic field induces a voltage in each coil antenna, and the voltage values are transmitted from the PAD back to a controller on the CMM wirelessly, typically at a frequency between 400 MHz and 2.5 GHz. These values are then used to determine the distance between the miner and the generators of the machine. Typically this information is used to determine when a miner wearing a PAD is in a warning zone or stop zone which would trigger different alarms and actions such as slowing the machine down or stopping it."

Jan 1, 2017

By R. J. Hickson

The Grasberg copper-gold deposit was discovered in Spring 1988, just one year prior to the planned closure of Freeport Indonesia's original Ertsberg open pit copper mine. In spite of Grasberg's remote location, 600m above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought their latest open pit mine into production in the last week of 1989, less than two years after discovery. This paper describes the start-up of the operation, highlighting synergies drawn from both the original Ertsberg experiences and the current Freeport Indonesia underground mines.

Jan 1, 1991

By Thomas Jancic

Two of the open-pit, copper-molybdenum mining operations of Duval Corporation are located in the foothills of the Sierrita Mountains approximately 30 miles southwest of Tucson, Arizona. In March 1959, mining from a moderate sized porphyry deposit known as the "Esperanza orebody" was begun at a rate of 10,000 tons of ore per day. Some five years later, a sizeable group of mineral claims west of Esperanza became available to Duval. Earlier exploration and development drilling in this area by others indicated an orebody of greater size but lower tenor than that of Esperanza. A drilling program conducted by Duval not only verified the results of the prior drilling but in addition, revealed a continuation of the mineralization to the south and east. Thus was developed the Sierrita orebody. Open pit design delineated 414 million tons of ore containing an average copper content of 0.35 percent and a molybdenum content of 0.036 percent. In April 1966, the office of Emergency Planning authorized General Services Administration to undertake a program under the Defense Production Act to en¬courage additional domestic production of copper in the interest of national defense. Duval's Sierrita Project was brought to GSA's attention in May 1966 on November 28, 1967, an agreement providing for the development of the Sierrita Property was consummated with GSA. In March 1970, the first copper-molybdenum concentrates were produced in the 72,000 tons-per-day concentrator. Pre-production stripping exceeded the scheduled 105 million tons despite the comparatively short lead time available to equip the mine, build the mine plant facilities, and staff the technical, supervisory, and labor forces. Shortly before the first concentrates were produced, plans were being formulated for a program to increase processing capacity by approximately 15 percent, which entailed increasing overall mining capacity by approximately 50,000 tons per day. This program is scheduled for completion early in 1971.

Jan 1, 1971

By F. Mielli

Over the last three years there has been an increase in mining congress and conferences focusing on water management. Water in mining is a key concern for mine managers and operations, and we are now seeing this operational dilemma escalated to the level it deserves. According to Frost & Sullivan research, mining water and wastewater treatment and its related technologies will be a U$3.6 Billion global market in 2016, which translates the importance of this issue. Looking at the current mining trends, some factors increased the importance of water in mining operations, including: ? Future mining investments will be located in geographical locations where water is scarce (water stressed areas) ? A decline in grade will increase the intensity of mineral processes and therefore increase the use of the water ? Increased sustainability and regulations will extend the control/monitoring of water during the entire mine life cycle representation of the mine water flow system. A water balance has several benefits/objectives in a mine operation: ? Mine planning/simulation of mining scenarios/climate change Production optimization ? Minimizing strategic and operational risks ? Social license to operate ? Water-smart mine planning ? Target: water neutral mines ? Benchmarking within and between sites ? Sharing knowledge/technology transfer ? Reporting/communications ? Permitting/Compliance

Feb 23, 2014

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicrometer size range and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicrometer size range. As dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using an impactor-type size selector such as the DPM impactor (DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) are an alternative size selector for DPM sampling applications, with a major advantage that, by design, they should not be susceptible to rapid aging. This paper presents the results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device and, eventually, a reduction of its effective particle cut size, but when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions of this study, the effects of SCC aging were observed to be minimal at the end of the study period. IntroductionSubmicrometer-sized particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, Gussman and Meyer, 2000; Ristovski et al., 2012). Diesel particulate matter (DPM) represents a major source of submicrometer particles in both public and occupational environments (Kittelson, 1998; Abdul-Khalek et al., 1998). Relative to other occupational groups, underground miners can have some of the highest DPM exposures due to their work in confined spaces where large diesel equipment is used (U.S. Environmental Protection Agency, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as soot, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the U.S. National Institute for Occupational Safety and Health (NIOSH) 5040 standard method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007; Birch, 2016)."

Jan 8, 2018

By Amy McBrayer, Andrea Brickey

Limited research has been conducted related to the development of mathematical optimization models for production scheduling at large surface coal mines using the area, i.e., strip, mining method. Increased economic and technical challenges have led to a new interest in production schedule optimization models for these type of mining operations like those currently applied to model underground and open pit mines. While area mines share similar characteristics to both open pit and underground metal operations, neither an open pit nor underground production scheduling model adequately depicts an area mine mathematically. We present an integer programming model with blending constraints and discuss the challenges and opportunities related to the implementation for area mines as well as future research in area mine production scheduling.

Jun 25, 2023

By M. De Ladurantaye-Noël, M. Laliberte

Selenium is widely present in the environment at usually low concentration. It is mostly present in the environment at higher oxidation states, i.e., as selenites and selenates (+4 and +6 oxidation states respectively). It is rarely present as selenides (-2 oxidation state) and almost never found as the element (0 oxidation state). Selenites and selenates are generally soluble in water, as such they cannot easily be removed from water by precipitation. Selenites can form insoluble surface complexes with metal oxides such as ferric hydrous oxide and manganese hydroxide, and can therefore be removed that way. However, it is not so common to find selenites in natural environments as it will quickly oxidize to selenate in aerobic conditions. Elemental selenium can also be produced from selenites or selenates by using a reduction process; the end product is a colloid that can be destabilized to be removed from water using the right chemistry. Because of their toxicity, selenides need to be handled with care, and if present, it can form insoluble metal salts or, at low pH, be emitted as H2Se, a noxious and highly toxic gas. The most favorable selenium forms for its removal are therefore selenite and elemental selenium. Organo-selenium species play a crucial part in understanding selenium toxicity. There are a great number of these species. Basically, any organic species that contains sulfur has an equivalent that contains selenium. Of particular interest is the substitution of sulfur by selenium in the two sulfur-bearing amino acids, cysteine and methionine, resulting in selenocysteine and selenomethionine. Methylseleninic acid (CH3SeO2H) is another organo-selenium specie which has been detected in water treated by biological processes and which is biologically active.

Feb 1, 2023

By Edmond J. O’Donovan

South Bulga is a new longwall operation located in the Hunter Valley coal-mining region in Southeastern Australia. The mine’s objective is to achieve productivity levels significantly higher than the current industry average. From the day longwall production began, South Bulga’s output was below both budget and industry expectations, primarily because of the poor performance of the conveyor system. In the past, conveyor systems have been seen as an adjunct to the mine plan, not as an integral part. At past production levels, this approach may have been acceptable. In today’s mining operations, the conveyor system must be treated as integral and vital to the mining operation. The conveyor system is analogous to the vascular or circulatory system of the human body. Of itself, the system does not do anything, but if it is not functioning satisfactorily, the mine cannot operate.

Jan 1, 1996

By M. R. Haibach, M. L. Shema, J. M. Silvis

"Since 2005, longwall coal mine operators in Pennsylvania (US) have been required to collect extensive hydrologic and biological data to document pre- and post-mining conditions of aquatic resources (streams and wetlands) overlying the subsidence control plan areas. Continued operation of the longwall mine is dependent upon empirical data demonstrating that the undermined aquatic resources have either been maintained or restored to an accepted range of pre-mining conditions. This study used quantitative hydrologic methods and comparative biological metrics to examine response of aquatic resources to longwall subsidence at the Bailey Mine located in Greene County, Pennsylvania. This study analyzed data from over 25 miles of streams and over 8 acres of wetlands that traverse the 4,779-acre study area. Hydrologic analysis of flow intermittency suggested that there are variable degrees of change to headwater streams immediately following mining; however, the majority of the effects are reversible through streamflow mitigation measures. Furthermore, the post-mining discharge from streams can be restored to within the range of pre-mining conditions the majority of the time. Biological assessments showed that greater than 95% of assessed stream length has maintained its ability to support benthic macroinvertebrate communities following mining and intervention (i.e., mitigation). Comparative metrics of the benthic macroinvertebrate communities showed that the biological community in 48 of the 50 sample sites is being maintained or restored across both high- and low-gradient streams. The effectiveness of intervention was further substantiated by the similarity in recovery times between streams having no intervention (median = 2.1 years, 95th percentile = 4.9 years) and streams with intervention, when recovery times were measured from the date of the intervention (median = 1.7 years, 95th percentile = 4.7 years). Changes to individual wetlands were observed between the pre- and post-mining assessments, but cumulatively a net gain of 7% in wetland acreage was realized. Hydrologic assessments were used to infer whether there was a potential that streams had been affected by mining; however, the ultimate test of stream recovery is based on biological metrics that establish the relative quality of the biological communities following mining. Overall, the hydrologic balance is being protected and the aquatic life use of streams is being maintained within the Bailey Mine’s subsidence control plan areas."

Jan 1, 2017

By William Hodder, Ehsan Alavi, Nader Ghasempour, Daniel Cressman

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km from Ashbridges Bay Treatment Plant west under Lake Shore Boulevard, north under Bayview Avenue and east through the Don River park area to the Coxwell Ravine Park. The tunnel is currently being mined by using a shielded dual-mode tunnel boring machine (open and close) capable of operating in EPB mode and lined by using a precast concrete segmental tunnel linear with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT is expected to be excavated mainly through shale bedrock of the Georgian Bay Formation, at approximately 50 meters deep. The tunnel crosses a buried bedrock valley in two locations, in the southern portion of the alignment, adjacent to the Don River, and at the northern portion of the alignment approaching the CX-1 shaft. In these two locations, the bedrock cover is expected to be less than 6 meters. The risk of encountering weathered bedrock, significant ground water inflows or surficial soil deposits through these buried valleys was identified during the design phase. The contract required the TBM to be designed with the ability to probe drill ahead of the TBM and convert to EPB mode if necessary, to cross this area. This paper will discuss the additional exploration that was performed by the contractor to identify the extent of this buried valley, the plan going into the zone of potential weathered shale, and the actual conditions encountered.

Jun 13, 2021

By Linda D. Raedeke

The main platinum-group metal (PGM) deposit in the Stillwater Complex is associated with a stratiform zone formed by magma mixing. In general, the intrusion is a large, layered body of Archean age which formed by repeated magmatic injections in- to a single, large, hypabyssal magma chamber. The Complex is broadly divided into the lower Ultramafic series of olivine ± orthopyroxene rocks (1000-2000 m thick) and the upper Banded series of predominantly plagioclase-rich rocks (24500 m thick). The latter is further divided into Lower, Middle, and Up- per Banded zones. The Ultramafic series, plus most of the Lower and Upper Banded zones formed from repeated injections of an olivine-saturated magma, the rocks accumulating from the floor upward with a crystallization order of olivine, or- thopyroxene, plagioclase, clinopyroxene. The olivine-bearing subzones of the Middle Banded zone formed predominantly from a magma which crystallized in the sequence plagioclase, olivine, clinopyroxene. Olivine-bearing subzone I, with which the PGM mineralization is associated, occurs generally -400 m above the Ultramafic series-Banded series contact. Ore grade mineralization is usually found in plagioclase or plagioclase-olivine cumulates. The platinum-group elements are associated with disseminated base-metal sulfides dominated by the assemblage, pyrrhotite-chalcopyrite-pentlandite. Olivine-bearing subzone I marks an interruption in the crystallization sequence of the Lower Banded zone, with the reappearance of cumulus olivine and an associated change of the crystallization sequence. These changes indicate the addition and mixing of a secondary magma of the same composition as that which later dominated in the formation of the Middle Banded zone. Characteristics associated with mixing include laterally discontinuous but well-developed layers, xenoliths of ultramafic rocks, and sedimentary-type structures such as slum- ping and graded layering. The influx of new magma caused sulfide saturation by one or more of several chemical changes including addition of sulfur, decrease in oxygen fugacity, decrease in FeO, or increase in SiO2. Once an immiscible sulfide liquid was formed, platinum-group elements were scavenged from the magma by the sulfide liquid and segregated.

Jan 1, 2013

By B. T. Lusk, Q. Q. Huang, R. Q. Honaker, K. A. Perry

Rock dust is applied in underground coal mines to prevent the propagation of coal dust explosions. It is applied either dry or wet. Both methods have advantages and disadvantages, but the formation of caked rock dust particles is cited as a significant concern for wet applications. We conducted a study to evaluate the effect of modifying the rock dust particle surfaces to repel water and each other by the addition of oleic acid and sodium oleate. At a sodium oleate dosage of 1 kg/t, a contact angle of 112o was measured, indicating strong surface hydrophobicity and thus the ability to repel water. Fourier transform infrared spectroscopy (FTIR) studies indicated a chemisorption mechanism, which is necessary for long-term stability of the surface modification. The dispersibility of the modified rock dust samples was elevated by the application of both oleic acid and sodium oleate, thereby indicating a significant reduction or elimination of the detrimental effect of caking. Tests in an explosion chamber showed an 82.8 percent reduction in the dust explosion potential relative to untreated rock test applied by the wet technique.

Jan 1, 2015

By R. C. Troxell

Alternative methods of analyzing data acquired by the Morenci copper concentrator process control instrument-computer system are presented. Experimental measures of ore characteristics, for proposed feed forward control, are introduced. These include on-line indexes of ore hardness, ore density, ore dusting, and ore color. Comparison of metallurgical results before and after computerized process control implementation, allowing for differing ore grades, oxidation, hardness, and fineness of grind, also is described.

Jan 1, 1979

By C. Ernst

The underground operation at Barrick?s Cortez Mine, located near Elko, NV, required the construction of a 12 foot diameter smooth-lined ventilation shaft. Barrick preferred to mechanically excavate from the ground surface without putting people in the excavation and considered blind drilling by Frontier-Kemper Constructors the best option. Design and construction challenges arose throughout both the excavation and lining stages. A large portion of the rock to be drilled was highly fractured. Important risks that were addressed included water loss into the formation, zones of squeezing ground, damage to drilling tools caused by blocky ground and fallout, and potential hazards during cast-in-place concrete lining. Detailed explanations of these challenges and the methods used to overcome them will be described.

Feb 23, 2014

By Francois E. Heuze

The mined geologic burial of high-level nuclear waste is how the favored option for disposal. The underground repositories must keep the waste away from the biosphere for very long times - several thousands to tens of thousands of years. Also, access must be maintained to the vaults for several tens of years, so that the waste can be retrieved, if necessary. Both the excavation of the underground chambers, and the radiogenic heating will disturb the rock mass. The overall rock mechanics problem is to understand and predict the processes associated with these perturbations, and their impact oh the isolation and containment of the waste (3)**. The specific rock. mechanics issues which have been identified for the three candidate hard rocks (basalt, granite, and tuff), are summarized in Table 1. The table also indicates the level of adequacy of our knowledge in the areas of the various issues. Such an evaluation is consistent with the general consensus of the rock mechanics profession, as explained in several key reports and publications (1 to 11). The main shortcomings of today's rock mechanics for waste repositories can be summarized as: ? lack of resolution for remote mapping of fractures in rock masses ? great difficulty in testing large volumes of rocks to determine their mechanical properties.

Jan 1, 1981

By R. M. Rowe, T. E. Irwin

A flowsheet was developed for upgrading Climax tin concentrate to about 45 percent Sn. Bench-scale test work conducted at AMAX Extractive Research and Development, Inc., was used to design a multiple-stage tin- processing flowsheet which included screening, high-intensity magnetic separation, and high- tension (electric- static) separation. Formal engineering and plant installation was accomplished in-house by Climax mill personnel. The successful start-up operation of the facility was the joint effort of the AMAX R&D and Climax-mill staffs.

Jan 1, 1986

By A. Festa

Secondary crushing often gets good press for its increases in energy efficiency and SAG milling rates but for a project considering this option the proposed benefits soon get overshadowed by implementation concerns. Reverse engineering from the published case studies is risky unless the reader understands the drivers impacting stability and operability of the circuit. This paper discusses the features of secondary crushing for Greenfield and Brownfield SAG mill grinding circuits. It is the author?s view that secondary crushing rarely adds value to a Greenfield project and restricts future expansion. Its application is best retro fitted to Brownfield operations where the benefit gained for capital expended is excellent. Two case studies are presented to reaffirm these statements. The first case study shows that the implementation of partial and total secondary crushing increases SAG mill power efficiency and it offers substantial incremental increases in milling throughput with staged capital investments for the crushing and grinding circuits respectively. The paper provides a critical analysis of process conditions for secondary-crushed grinding circuits, with particular emphasis on Brownfield circuit retrofits. Furthermore, the second case study quantifies the economic impact of secondary crushing on circuit design for plant start up and it illustrates the limit imposed on plant expansion.

Feb 23, 2014

By James G. McKelvey

Owners have seen several major tunnel projects in recent years fall victim to a general reduction in the number of bidders as well as an erratic range of pricing. It should be noted though that this is not a universal trend and some projects have seen good competitive bids. Contractual terms and conditions are an important factor in attracting good competition. The Front End documents of tunnel projects have come under increasing scrutiny as tunneling contractors in the U.S. industry are looking much more closely at their risk exposure in the contract terms and conditions. Considering the amount of tunnel construction work upcoming in North America, it is important that General and Special Conditions are put together in a way that provides a reasonable basis to execute the Contract and also provide a fair, balanced and swift way to resolve disputes.

Jan 1, 2008

By J. F. T. Agapito, L. J. Gilbride

High horizontal stresses were recognized to impact roof stability more than 60 years ago. Since then, numerous measurements associated high horizontal stresses with difficult ground conditions. This paper presents case histories illustrating the practical usage of roof stress determinations for helping assess stability, not only in the case of high horizontal stresses but also of low stresses. Examples are given of high stresses associated with faults, mine design changes, quantification of stress shadow effect, and anistrophy. The paper concludes with a comparative evaluation on the effect of various stress fields on ground support requirements.

Jan 1, 2002

By M. Downing

This paper gives a brief overview of impacts of coal blending on coal-fired power plants performance and discuses the preliminary results of an on-going study aimed at evaluating the effect of coal properties on the effectiveness, compatibility and thermal reactivity of coal blends. Plant survey studies reported no significant impacts on an existing plant designed for a high rank coal when switched to a blend of low-and high-rank coal. However, slight modification of some aspects (handling, fuel storage/stockpile, transportation, preparation, and general housekeeping) of plant design and operation may be necessary. The preliminary results of an on-going study at the Mineral Industry Research Laboratory shows that more compatible and better blends could be made from coals where ranks are closer than from those where ranks are far apart.

Jan 1, 1997