Search Documents

By Rob Thomas

It is generally agreed that standing support should be installed in roadways that will for various reasons, be holed through with a longwall. Considering the magnitude of the associated abutment loading in conjunction with the need to ensure that the material used is cuttable, some form of cementitious support is often used.

By K. V. Raj, R. Jacksha

Conveyor systems persist in being a source of injuries and fatalities in the mining industry. To reduce these incidents, better methods are needed to enhance the monitoring of probable hazards and improve situational awareness during the normal operation and maintenance of conveyor systems. To address these issues, researchers from the National Institute for Occupational Safety and Health (NIOSH) continue to investigate emerging technologies that show the potential to improve miner safety around conveyors. This paper presents a feasibility assessment by NIOSH researchers of a fully integrated, commercially available wireless Internet of Things (IoT) system to improve situational awareness around conveyor systems. Included are discussions of a full-scale laboratory test bed that was designed to simulate a working conveyor system as well as the challenges and successes of integrating the IoT system with the test bed.

Oct 6, 2020

By P. Bissert, M. Klein, L. Yan, D. Yantek, R. Matetic

"U.S. Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hours. One of the main concerns with the use of mobile RAs is heat and humidity buildup inside the RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in an occupied RA not exceed 95 °F. To investigate this, the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4 °C (17 °F) and the relative humidity approached 94 percent at the end of a 96-hour test. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the volume-weighted average air temperature inside the RA tent at the end of 96 hours to within 0.06 °C (0.1 °F) of the average measured air temperature. IntroductionIf an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter a refuge alternative (RA) for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration, and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke or even death."

Sep 1, 2016

By PDF

Flotation columns are widely used in mineral processing and coal preparation industry today. Mathematical modeling of flotation columns has conventionally been done using axial dispersion or tank-in-series models. However, for design and scale up purposes these models are not adequate enough because they do not provide detailed information of the flow fields within the column. This paper presents a Two-Dimensional, Two-Phase. Fluid-dynamic Model and its numerical solutions for some cases encountered in column flotation. The MAC (Marker and Cell) method was employed to obtain the numerical solutions, and based on this method a computer code COLUMNFLOW was developed. The simulated flow field reveals the presence of a circulation flow structure in flotation columns, which could be one of the main reasons for mixing in column flotation. The effects of some parameters such as superficial gas and liquid velocities on the characteristics of the flow structure in flotation columns were also tested with the numerical model.

Jan 1, 1994

By S. D. Van Nort

The Grasberg porphyry copper-gold deposit of Freeport Indonesia Inc., an 81% owned subsidiary of Freeport-McMoRan Inc., lies within the Ertsberg Mineral District in central Irian Jaya, Indonesia. The Grasberg deposit was discovered during a drilling campaign initiated in early 1988. Production at the open pit Grasberg deposit commenced in December 1989. The Grasberg copper-gold orebody is contained with a young igneous complex of dioritic composition which intrudes limestones of the Tertiary New Guinea Group. Alteration is typical of porphyry copper deposits worldwide except that higher grade primary chalcopyrite with significant gold values is associated with a centrally located zone of strong quartz stockwork.

Jan 1, 1991

By James C. Hower, B. K. Parekh

Introduction The purpose of coal preparation is to improve the quality of coal to make it suitable for a specific purpose by (1) cleaning to remove inorganic impurities; (2) sizing-crushing or screening, or both; and (3) special treatment, such as dedusting. The properties and quantities of impurities in coal are of major importance in the design and operation of steam generating equipment. Although boilers are often designed and equipped to use a wide range of coals, no boiler will perform equally well with all types of coals. All coals have certain properties that place limitations on their most advantageous use. These limitations are especially stringent for many of the older installations. Because of a general lowering of quality of raw coal in recent years, the need for coal cleaning has significantly increased. Among the factors contributing to the need for increased coal preparation are (1) increased demand for quality brought on by market and environmental requirements; (2) increased extraneous dilution caused by mine, health, and safety laws; and (3) depletion of the higher-quality coal seams. The major characteristics of coal and impurities from the standpoint of mechanical cleaning are particle size composition, generally called size consist; density differences; the relative friability of the coal and its associated impurities; hardness; and strength. Some of the other factors related to preparation are petrographic composition and rank. RANK CLASSIFICATION Coal is a general designation for a great number of solid organic minerals with different compositions and properties; all are rather rich in carbon and have a dark color, generally black. Next to mineral oil and kerogen, coal is the most important reservoir of carbon in the world. Carbon is an indispensable necessity of life as well as the main source of energy. Coals are found in stratified deposits, sometimes at great depths. All coals owe their origins to slow decomposition and chemical conversion of immense masses of organic material. As found in seams, coal is a heterogeneous mixture of organic and inorganic materials. Not only are there large differences in the properties of coal originating from different seams, but also in coal removed from different locations in a single seam. A genetic relationship exists between peats, brown coals, lignites, biturninous coals, and anthracites. As a whole, the process of coal formation, or coalification, proceeds as a continuous transformation of plant material, each phase characterized by a degree of coalification, or rank. As a measure of this rank, the carbon content or some related parameter can be used.

Jan 1, 1991

By R. J. Matetic

Mining operations have long been accused of causing a disruption to local, domestic and agricultural water supplies. More recently, concern for water supplies has increased with the advent of high-extraction mining techniques, namely longwall mining. Theoretically, any water bearing zone in the overburden above a high-extraction mining operation may be affected by mining. In some cases, a confining bed may be fractured causing a loss of water to a particular zone. In other cases, increased fracture permeability may enhance the ability of an aquifer to transmit and deliver water. Unfortunately, only a limited amount of studies have been conducted that characterize hydrologic changes and also quant1fythe magnitude of mining-induced subsidence. The U.S. Bureau of Mines conducted such a study at a mine site located in Greene County, PA. A total of 8 water wells were drilled and hydrologic parameters such as specific capacity, transmissivity and well yield were determined both before and after mining. Electronic water level recorders were installed on each water well to provide continuous observations of water level fluctuations.

Jan 1, 1990

By A. A. Zatout, G. H. Sedahmed, T. M. Zewail, M. H. Abdel-Aziz, B. S. Ibrahim, E-S. Z. El-Ashtoukhy

In this work, the possibility of intensifying the cementation process in stirred vessels was studied by using the perforated baffles as turbulence promoters; the cementation reaction of Cu+2 on Zn was selected as a model. Zn was used in the form of a sheet lining the inner wall of an agitated vessel. Parameters considered are initial concentration of Cu+2, solution temperature, impeller rotation speed, and impeller geometry. Within the present range of parameters studied, the rate of cementation was found to increase with increasing initial concentration of Cu+2, solution temperature, and impeller rotation speed. At the same rotational speed, a flat turbine gave a higher rate of cementation than a 45° pitched turbine. The present suggested that baffles’ geometry gave superior performance in terms of mass transfer of copper cementation compared to the conventional baffle geometry. All parameters that affect the rate of cementation were correlated in the form of dimensionless equations suitable for the design and performance prediction of the agitated vessel. Potential applications of the obtained results in the field of hydrometallurgical processes and wastewater treatment were discussed.

Jan 12, 2021

By Parris A. Lyew-Ayee

The Government or Jamaica has just completed agreements with four of the five bauxite/alumina companies operating in Jamaica. These companies are Kaiser, Reynolds, Alcoa, and Alcan, and the Agreements came into effect on February 1, 1980. One of the results of these new Agreements is the Acquisition of all company-owned bauxite lands by the Government and the rationalization of bauxite reserves.

Jan 1, 1980

By Edwin W. Tooker

Creation of needed new resources will be accomplished mainly by imaginative and diligent geologic exploration because geologic availability is the key determinant of future mineral supply. Adequate resources of most commodities can be made available for the rest of this century and beyond if they are discovered. Thus conversion of hypothetical and speculative resources into available reserves will provide the principal challenge to earth scientists. Additional problems now compete for our attention. First is a challenge to discover more resources than have been found to date for domestic needs as world-wide demands increase exponentially and as easily found high-grade deposits are rapidly being depleted. New ways to find new types of deposits are required. Second, the United States, a resource importer, increasingly is challenged for access to foreign supplies through stiffening competition and economic or expropriation sanctions. Balancing needs for mineral supply and environmental protection is a third challenge. Geologic explorers must consider statutory as well as economic and technologic requirements, controlled access to public and private lands, competition with urban sprawl or wilderness, limitations on discovery, appraisal and mining methods, and restoration of mined areas. Finally, is the challenge to temper public and private attitudes and assure that decisions bearing on resource problems are based on comprehensive credible facts. While striving to maintain and improve the standard of living, many Americans appear to disdain and mistrust those organizations that provide their material where-withal. Meeting these challenges effectively, and in time, will require careful appraisal of the resource system and the joint efforts of industry, university, and government earth science research.

Jan 1, 1974

By J. F. Hutwelker

A pilot plant was constructed and operated to investigate the column flotation of 20 x 200 mesh North Carolina phosphate ore, using high throughput, high solids operating conditions developed at the NCSU Minerals Research Laboratory. Flotation was performed at 45% solids in a 9.5 cm (3.75 in.) diameter by 2.26 m (7.4 ft.) tall column at throughputs of 19.1 t/hr/m2 (2.0 stph/ft2) and 31.7 t/hr/m2 (3.3 stph/ft2). Recoveries in excess of 98% of the phosphate value were obtained at the lower throughput -- while obtaining concentrate grades containing over 28% P205 (61.2% BPL) at that recovery. Recoveries of about 95% of the phosphate value were obtained at the higher throughput, while making a concentrate averaging 27.6% P209 (60.3% BPL). In addition, a better understanding of the variables governing the column flotation of coarse nonmetallic minerals was gained. Low air flow rates adversely affected concentrate grade at the lower throughput. At the higher throughput, phosphate recovery decreased at an elevated air flow rate. An unexpected result of the study was the effect that frother type had upon phosphate metallurgy. Use of Nottingham Econofroth 925 provided better flotation selectivity than American Cyanamid F-65 at the low throughput. This is significant since the high' throughput tests were conducted with F-65 exclusively. It is reasonable to expect further improvement in high throughput performance when the optimal frother type and dosage are determined.

Jan 1, 1993

By W. D. Hausel

The Wyoming Province is an Archean craton which underlies portions of Idaho, Montana, Nevada, Utah, and much of Wyoming. The cratonic block consists of Archean age granite-gneiss with interspersed greenstone belts and related supracrustal terranes exposed in the cores of several Laramide uplifts. Resources found in the Province and in the adjacent accreted Proterozoic terrane include banded iron formation, Au, Pt, Pd, W, Sn, Cr, Ni, Zn, Cu, and diamonds. The Province shows many similarities to the mineral-rich cratons of the Canadian shield, the Rhodesian and Transvaal cratons of southern Africa, and the Pilbara and Yilgarn blocks of Western Australia, where much of the world's precious and strategic metal and gemstone resources are located.

Jan 1, 1991

By Josef Arnold, Norbert Fuegenschuh

The “Eggequerung” is an important part of the German Railway’s (Deutsche BahnAG) modernized Dortmund—Kassel line. The heart of this 13-km-long (8 miles)construction lot is the double-track Egge Tunnel with a total length of 2,880 m(9,450 ft.). The tunnel was driven using the New Austrian Tunnelling Method (NATM).The construction contract also called for a reinforced concrete secondary lining, guaranteed for a full water pressure of 30 m (100 ft.) water column. Preliminary geological study already showed that very problematic geological-hydrological conditions would have to be expected. This talk describes the chosen NATM driving concept that was adapted to the prevailing geological and hydrological conditions, the special driving method applied in geologically difficult zones as well as the water control concept used during driving. The flexibility and the limits of the NATM under exceptional hydrological conditions are illustrated. Also described are reinforced concrete lining works for the watertight secondary vault (reinforced concrete secondary lining without water-proofing membrane).

Jan 1, 2003

By Frederick C. Moore

This paper describes the original planning which actually resulted in the opening of a new aggregate plant located in central New York State. This plant, which is now named the Skaneateles Plant of The General Crushed Stone Company is unique in that the plant itself is a departure not only in design but in concept of operation from the normal aggregate plant the company has operated in the past. Whether or not the concepts which resulted in the Skaneateles Plant are economically feasible remain to be proven by the next few years of operation. By way of background data about our company which will help set the stage for this presentation, we currently operate seventeen stone quarries in the states of New York, Pennsylvania and Virginia. These quarries range in size from 200,000 tons per year to 1,500,000 tons per year with a total annual stone production of approximately 7,500,000 tons. We also produce about 1,250,000 tons of sand and gravel at six sand and gravel plants, 300,000 cubic yards of ready mix concrete, 1,500,000 tons of bituminous concrete, aglime and other minor construction materials. In many cases we are our own best customer consuming a large percentage of the total production of our own aggregates in our various ready mix and blacktop plants. Up to the concept of the Skaneateles Plant our operating facilities have been of the permanent type as opposed to the moveable or portable type plant. The steps involved in the case history of Skaneateles will begin with the basic economic requirements, market research, geologic surveys, land acquisition, zoning and financing and carry through to the final design and construction. We will attempt to show what some of the problems were, how we interpretted them and how we proceeded to solve them. The current results are apparent and can be analysed. The success of the total concepts of the Skaneateles Plant remains for future analysis.

Jan 1, 1968

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, Matthew Gordy, Patrick Zhang

Waste phosphatic clay presents a difficult disposal problem and a significant loss of P2O5. Recent developments make this study on the use of phosphatic clay as a feed material for H3PO4 production worthwhile. (a) New data from Florida Industrial and Phosphate Research Institute (FIPR) suggest that the Bclay^ waste can be effectively treated by improved solid separation coupled with flotation to produce feed material for recovering additional phosphate. (b) The use of BOLI Flowsheet^ provides capability to predict performance of aqueous-based processes for a range of possible operating conditions. Using the new FIPR data and BOLI Flowsheet^ enabled the design of a new process that can potentially extend the usefulness of current P2O5 ore deposits. Predictions using OLI Flowsheet were able to identify process conditions that effectively overcome the difficulty of high Mg content of phosphatic clay. Estimated manufacturing cost in the current study lead to valuation of the P2O5 content of the phosphatic clay recovered/utilized at 60 to 70% of that of the phosphate rock feed material currently used. Phosphatic clay should be considered as a valuable material that is currently given zero value. The new FIPR data and BOLI Flowsheet^ enables the design of a new process that can potentially extend the usefulness of current phosphate ore deposits by extending the fraction P2O5 of recovered

By Craig J. Nelsen, J. Leroy Schutz

The Carache Canyon Prospect consists of a hypabyssal breccia pipe which intrudes a gently dipping sequence of Cretaceous Mancos Formation and Mesa Verde Group shales and sandstones. This sedimentary sequence is intruded by a number of Oligocene (34-30 Ma) calc- alkaline sills. The formation of the breccia pipe and its subsequent gold mineralization is related to the emplacement of an alkaline intrusive complex dated between 30-26 Ma. An exceptionally large block within the pipe provides compelling evidence that brecciated sills and sedimentary rocks form a relict stratigraphy that collapsed 400-800 ft (120-240 m) below their counterparts outside the pipe without substantial changes in stratigraphic position. Native gold and sulfide mineralization within and around the pipe occurs in fractures that are primarily controlled by competency differences between sills and sedimentary rocks and secondarily controlled by ductility contrasts between the relatively brittle Mancos Formation hornfels and the more ductile Menefee Group shales. The resulting pattern of gold mineralization is a series of stacked, tabular, mineralized sills and sandstone separated by barren shale in an annular region along the southwest margin of the pipe. A series of near-vertical, subparallel, sill and sandstone breccias separated by barren or weakly mineralized shale breccia occur within shallow levels of the pipe.

Jan 1, 1990

By Manchao He, Xiaoding Xu, Yubing Gao

Based on the geological conditions of the 15,600 working face in Pingba Mine, this paper establishes the mechanical model of the stress distribution in the pre-working face under the influence of mining pressure based on a hemispherical stress distribution theory. The analytical formula for the stress distribution is determined. A numerical model for the mining pressure under the influence of key layer is also constructed, and dynamic stress interruptions under various roof-cutting relief schemes in different horizontal positions are simulated. The stress distribution of the stope under different pressure relief schemes is analyzed and compared with the theoretical results. Results show that blasting roof cutting blocks the transmission of the abutment pressure to the working surface to the coal and rock mass in front of the working face, reducing the significant working face mining pressure influence range, which decreases as blasting pressure relief position moves toward the working face. Stress accumulation in the coal in front of the working face also increases as the blasting pressure relief position moves toward the working surface. Engineering practice results show that blasting cutting can effectively block the propagation of mining pressure, and the stress impact range is shortened by approximately 1/3.

Jul 31, 2021

By T. Bednarski, T. McCallum, L. Moya, B. Gay

"Molybdenum recovery by solvent extraction has gained interest partly due to advances in concentrate leach technology. Historically, both molybdenum and rhenium have been produced using amine-based extractants with the ability to co-extract both metals. Alternatively, a phosphinic acid-based extractant (CYANEX® 600) can be used depending on the flow sheet. CYANEX® 600 selectively extracts Mo leaving Re in the raffinate, which is a valuable feature in plants which require rejection of the rhenium from the molybdenum circuit. CYANEX® 600 piloting results are reviewed and compared to commercial experiences with an amine-based extractant. INTRODUCTION Molybdenum is most commonly found as molybdenite (MoS2) in primary porphyry deposits (about 59% of global reserves) and copper porphyries (about 39% of molybdenum reserves)[1]. Recovery from molybdenite traditionally involves flotation (concentrates typically containing 85 – 95% MoS2) followed by roasting to produce MoO3. Solvent extraction is also used to recover molybdenum from acidic aqueous solutions resulting from scrubbing of roaster and smelter off gasses and leaching of molybdenite (uranium ores). Molybdenum is also frequently found in low concentrations in copper leach inventories[2]. More recently, pressure oxidation has gained interest to treat molybdenite concentrates. Molybdenum Chemistry The chemistry of molybdenum is complex with a series of extractable species existing dependent on the pH and oxidation state as shown in Figure 1.Under strongly basic conditions, molybdenum primarily exists as MoO42- while under strongly acidic conditions MoO22+ becomes the predominant species. In between, a number of isopolymolybdates such as Mo7O246- and Mo8O264- are dominant. Equations (1) – (3) demonstrate some of the proposed molybdenum equilibrium reactions[1]."

Jan 1, 2017

By R. Mensah-Biney

The loading characteristics of gold-tetrabromide species onto activated carbon have been evaluated using a completely mixed batch reactor system. The overall loading of gold onto carbon was rapid for the first hour but continued slowly without cessation as a result of reduction of gold. Conventional equilibrium considerations were therefore not applicable. Although loading continued slowly after several days, abnormally high loading capacity values of 10-12 meq/g carbon (650-800 kgAu/tonne) could be attained within 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of [AuBr4l-onto the carbon surface where reduction to metallic gold took place. Elution of gold from the loaded carbon was feasible provided the carbon had not been loaded to too high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon is discussed.

Jan 1, 1992

By H. Sevim

In this paper, the research effort in simulating the operation of underground coarse-coal hydrotransport systems (UCCHS) is summarized. The equipment of the system to be simulated is already optimally selected by using an analytical optimization model. The purpose of the simulation model is to test the performance of the system and to obtain the distribution of the operating parameters such as water and power consumption, amount of slurry delivered to the preparation plant, etc. Knowledge of the distribution of these parameters is essential for the efficiency of the design and the operation of the system.

Jan 1, 1985