Search Documents

By Jr. Gambrell

For more cost effective strata control, a fundamental understanding of the behavior of the support system is needed. To assist in this understanding for shield supports, behavior of a four-leg shield design used on a soft floor in an operating longwall system is presented. The shield was constructed having a split base and a split caving shield. Attention is focused on other-than-normal loading on the canopy and its effect on deformation of the lemniscate links. Examples of the typical bending and twisting deformations are given. Schematics of the canopy, caving shield, and lemniscates showing important forces and moments are presented. Approximate minimum values of the forces and moments are calculated. The need for use of more inclusive three-dimensional design techniques is demonstrated.

Jan 1, 1990

By M. Moats

Copper electrowinning operations have dramatically improved their ability to produce high quality copper at low costs over the past several decades. Even so, some fundamental knowledge is still lacking that could allow operations to run even more efficiently. For example, a rule of thumb exists that estimates a current efficiency loss of 2-3% per gram per liter of iron in the electrolyte. While several laboratory studies have been performed that demonstrate this rule of thumb is likely true, no definitive relationship exists. In this paper, the first steps in developing a definitive relationship are presented. The effective diffusivity of ferric ions in synthetic copper electrowinning solutions was measured using chronoamperometry and the Cottrell equation. The effective diffusivity of ferric ion was determined as a function of electrolyte concentration and temperature. Synthetic electrolytes were then used in laboratory-scaled copper electrowinning experiments, where relationships between current efficiency and solution composition were found to exist under stagnant conditions. Key words: Copper electrowinning, Current efficiency, Chronoamperometry, Ferric ions

Jan 1, 2009

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch type stirred mill. The experimental results were evaluated using stress intensity analysis. The performance was also compared in terms of mill orientation. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1*10−3 to 5*10−3 Nm at 750 and 1500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value. Additionally, to the best of the authors’ knowledge, this is the first study to compare mill orientation (vertical vs. horizontal) for the same mill and under the same test conditions.

Apr 21, 2021

By M. Baumann

Operating and maintaining the heavy equipment used in open-pit mining operations is an ongoing challenge for mines. Typical operations employ a combination of shovels, wheel loaders, and haul trucks to excavate and transport the material for further processing. As this is the first point of contact for the material after blasting, it is often a bottleneck of all downstream processes, thus, equipment uptime and efficiency is crucial. Automated systems for bucket tooth monitoring, payload measurement, proximity detection, and rock fragmentation analysis will be examined. The impact of these systems on operation safety, efficiency, and reliability, in real-world scenarios will be investigated. The process of managing all the above fleet of equipment in a mine can be streamlined by connecting the equipment monitoring systems to a central server. Using the central server, the distribution of this information can be automated to ensure that the right people see the data in a timely manner, improving both proactive and reactive responses to threats to safety and productivity.

Feb 23, 2014

By Isa Nozari, Asghar Azizi

The extraction of copper from sulfate leaching liquor was investigated using Acorga M5640 commercial extractant in kerosene diluent. The effects of important factors such as the extractant concentration, contact time, liquor pH, and temperature were examined on the separation factor Cu/Fe and the extraction efficiency of copper. The results indicated that nearly 92.32% copper was extracted from the leach liquor at 10% (v/v) Acorga M5640 concentration, 1:1 aqueous/organic phase ratio, 20 min contact time, pH 2.5, and 25 °C temperature. Also, the further increase in the values determined had no positive impact on the extraction of copper. Under these conditions, the separation factor Cu/Fe was obtained about 29.64. The extraction mechanism was studied applying the plot of log(D) – 2 pH against log [extractant] and it proved the association of two moles of Acorga M5640 for the extraction of one mole of copper. McCabe–Thiele diagram was constructed and a single-step extraction process was found to obtain themaximumextraction. Additionally, thermodynamic datawere investigated and the extraction process was endothermic and non-spontaneous at 298 K (ΔH = 27.05 and ΔG = 15.52 kJ mol−1). Moreover, the loaded organic phase was stripped and 80.94% copper was recovered after 20 min using 10% sulfuric acid concentration.

Jul 31, 2020

Obtaining financing for mining and exploration projects has been difficult for the last several years, particularly for junior companies. Today, though, the purse strings of investors appear to be loosening, leaving the industry with many questions about financing in the coming years. How have capital markets and exploration spending changed? Are there signs of improvement? Where has capital been raised in private, public markets, stock exchanges, private equity, etc.? What companies successfully raised capital in the last year? How are they spending it? How are traditional and alternative funding sources investing in mining? What are the issues mining companies need to know about when tapping alternative sources of capital? Those were some of the questions that were answered at the Current Trends in Mining Finance conference, sponsored by SME and the New York Section April 26-28. Held in New York City, the conference attracted 115 professionals who work on the finance and economic side of the mining industry. Three of the conference organizers talked with Mining Engineering about the conference and the state of financing in the industry today. Tim Alch (TA) is managing director with Behre Dolbear & Co. Alan Oshiki (AO) is executive vice president with the Abernathy MacGregor Group. Henry Weingarten (HW) is managing director with the Astrologers Fund Inc. Here is what they had to say.

By E. K. Albert

In 1977, Congress enacted Title IV of the Surface Mining Control and Reclamation Act (SMCRA), providing for an "abandoned ml.ne reclamation fund". This fund, taken from a fee collected from operating coal mines, provides capital for the reclamation process. However, given the number and extent of abandoned mine sites in some states, the question of project selection is important. This paper describes a project in progress to create a Management Information System application for project ranking under multiple objectives. The benefit of this project for the need of new environmental control technologies will be discussed.

Jan 1, 1990

By G. L. Simmons.

Many large. low-grade (refractory) sulfide gold resources exist in Nevada and other parts of the world that are not amenable to concentration by conventional flotation practice, Over the past several years Santa Fe Pacific Gold (SFPG) has investigated flotation process options to economically treat low-grade refractory resources of this type at Lone Tree and Twin Creeks. Conventional flotation technology applied to the original high-grade gold resources at Lone Tree and Twin Creeks was initially unsuccessful. Review and analysis of auriferous (gold-bearing) iron sulfide mineralogical characteristics and flotation chemistry provided a fundamental understanding that led to the development of a new flotation process that SFPG refers to as N2TEC. This paper discusses the development of this technology and compares N2 TEC results with conventional flotation practice.

Jan 1, 1997

The mining industry is an important economical factor in Vietnam. Mining is presently being conducted at about 60 locations and at over 1000 mines. Petroleum extraction and coal mining are the most important parts of industry though metals such as zinc, tin, chromites, iron are also extracted. Last year the sector produced 20 million tons of crude oil, 26 million tons of coal and 500,000 tons of apatite. In particular, Vietnam is one of the world?s largest producers of anthracite, and it is one of the top producers of ilmenite and zircon in the Asia-Pacific region. The government intends to increase the mining production on all levels, however, at present one can observe adverse impacts of the mining activities on the natural environment such as insufficient waste dump rehabilitation, occurrence of acid mine drainage, mining subsidence and emissions as well as lack of appropriate water treatment facilities. This paper describes the current mining situation, future perspectives, the major environmental challenges of the country and approaches to solve these problems. Particular emphasis will be given to the research project ?RAME ? Research Association on Mining and Environment in Vietnam?, a venture carried out by universities, research centres and industry. This project is worked out in collaboration with the national Vietnamese coal and industrial minerals company VINACOMIN.

Jan 1, 2006

By K. KAKLIS, O. SAUBI, Z. Agioutantis, R. JAMISOLA

Three-point bending (TPB) tests were conducted on prismatic Nestos marble (Greece) specimens. The specimens were instrumented with piezoelectric sensors, and comprehensive recordings of acoustic emission (AE) signals were obtained. Machine learning in the form of artificial neural networks (ANNs) was then applied in an effort to investigate whether specimen load evolution can be predicted as a function of AE signals. A number of ANN models were developed, and the optimum model was selected based on the highest coefficient of determination (CoD) value as well as the lowest root mean square error (RMSE) value that was calculated for each model. The best performing ANN model exhibits accuracy above 99% with an RMSE value below 4%. It can be concluded that ANNs can potentially be applied to predict rock behavior under load especially when such loads lead to failure.

Sep 7, 2022

By R. L. Virta

Four companies ? H.C. Spinks Clay Co., Inc., Imerys, Old Hickory Clay Co., and Unimin Corp. ? mined ball clay in four states in 2013. On the basis of preliminary data, production was 1 Mt (1.1 million st) with an estimated value of $47 million. Production increased by 3 percent in tonnage from 973 kt (1.1 million st) with a value of $45.1 million in 2012. Tennessee was the leading producer accounting for 64 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 67 percent of total ball clay production was airfloat, 22 percent was crude or shredded and 11 percent was water-slurried.

By Peter E. Price

Salt dome hosted metallic sulfide deposits are the product of a complex evolutionary system involving halokinesis, cap rock development and diagenesis, and the generation, migration, and accumulation of basinal brines and hydrocarbons. Hydrocarbons play an important role in: (1) the production of calcite cap rock which hosts some of the metallic sulfide and sulfur concentrations, and (2) the generation of the reduced sulfur available for metallic sulfide precipitation and sulfur formation. Hydrocarbons and related fluids also are involved in the transporta¬tion and remobilization of the metals. Hydrocarbon consumption, in the course of cap rock development and sulfide mineralization at Hockley dome, is estimated to have been 6.4 million barrels of oil or 114 million cubic feet of methane. Mineral textures, including cap-rock banding, sulfide bands in anhydrite, and fine sulfide mineral banding indicate both episodic fluid influx and fluid compositional differences through time. Features such as pyrite "shells" and sphalerite and marcasite hemispheres may have been localized by hydrocarbon droplets and /or bacterial colonies. Marcasite mineralization in shallow strata above and flanking Hockley dome is best developed over the western and southern parts of the dome. This pattern mimics the known distribution of sulfide mineralization, which is dominantly marcasite, in the underlying cap rock. The iron sulfide paragenetic sequence in the sediments is pyritohedral and cubic + pyrithohedral pyrite followed by marcasite which is encrusted by cubic pyrite. Sulfur isotopic averages for the three stages are +20.8, -20.2, and +6.4 per mil, respectively. These values generally coincide with cap rock sulfate (+20 per mil), cap rock hosted metallic sulfides (-20 to +4 per mil), and sulfur in hydrocarbons (+5.8 per mil). Hydrocarbon compositions indicate provincial variations in oil composition and generation history. Long Point and Boling domes, which have an intergrown sulfide-sulfate-sulfur mineral assemblage indicative of mixed reducing-oxidizing environment, contain oils that are less mature than Hockley dome which appears to be more mineralogically segregated. Sterane biomarker compositions of the oils at Hockley, Long Point and Boling domes indicate a local, dominantly terrestrial source. An oil sample from supracap sandstones on the northeast flank of Hockley dome contained over 750 ppm combined Fe, Zn, Pb, and Co, indicating that hydrocarbons are carrying or remobilizing metals. Cap rock calcite and anhydrite also exhibit provincial variations in strontium isotopic ratios. Calcite and anhydrite cap rocks from several sulfide mineralized domes in the Houston diapir province have strontium isotopic ratios that are more radiogenic than Jurassic sea water (>0.7078). A calcite sample within massive sulfides at Winnfield dome also has a high 87Sr/86Sr ratio (0.7085). Variations in strontium isotopic ratios with strontium content indicate the mixing of at least three Sr-bearing fluids in the cap rock environment, one of which may have been the metal carrier. Anhydrite residues from diapiric salt have strontium ratios up to 0.7100, considerably more radiogenic than Jurassic seawater. These high ratios indicate either that salt and anhydrite recrystallized sometime post-Jurassic in the presence of a fluid with a high 87Sr/86Sr ratio, or that they precipitated in the Jurassic from a fluid with a higher 87Sr/86Sr ratio than Jurassic seawater. Salt domes with cap rocks containing metallic sulfides have only been found in basins that have geopressured zones. Waters from geopressured zones in the vicinity of mineralized salt domes have salinities that are two or more times higher and iron and base metal concentrations that are three to one thousand times higher, than geopressured fluids from other parts of the basin.

Jan 1, 2013

By W. H. Jang

Recent research has demonstrated the utility of the FTIRIIRS adsorption density equation for in-situ study of surfactant adsorption phenomena at the surfaces of reactive internal reflection elements (IREs). The FTIR/IRS adsorption density equation is given by (formula) where r is the adsorption density, A/N is the absorbance per reflection, e is the integrated molar absorptivity, 4 is the bulk concentration of the surfactant, d. is the effective thickness, and dP is the depth of penetration. Previously, the validity of the adsorption density equation had been confirmed only from solution depletion measurements with high surface area powders. Now, FTIR/IRS studies of Langmuir-Blodgett (LB) monolayer films of fatty acid transferred to the surface of a calcium fluorite IRE .clearly validate the reliability of the FTIR/IRS adsorption density equation for quantitative analysis of surfactant adsorption. In addition, it was confirmed from the observed absorption band at 1550 cm-1 that the first monolayer of the transferred fatty acid chemisorbs at the surface of fluorite.

Jan 1, 1994

By Vince Saporito

Miners work in dangerous terrain, around the clock, with heavy equipment. Is there room for improvement in safety and standardization in the mining industry? Recent history would suggest there is a need for action. At a 2011 Spring Thaw conference in Denver CO, one speaker commented, ?We are having a number of incidents with workers getting ?pulled? into rollers or ?trapped? at transfer points when trying to manually clean (it) while the conveyor is still in motion.? It?s a troubling thought. These actions are specifically prohibited under U.S. Mine Safety and Health Administration (MSHA) regulation 57.14202. Another official from MSHA earlier this year indicated with today?s technology and policies presently in place, ?we should not be repeating the same incidents and violations year after year as we currently do.? But we are doing exactly that.

Jan 1, 2012

By James J. Komadina

INTRODUCTION Newmont Gold Company's Rain operations are located in Elko County, Nevada, approximately 9 miles southeast of the Town of Carlin.The property was submitted to Newmont Exploration Limited in 1979 and underwent development drilling over the course of the next four years, culminating in the completion of a project feasibility study in October 1986. Initial project scope included development of an open pit mine, an 815,000 DSTPY heap leach, a 572,000 DSTPY mill (Mill No. 3), and associated support facilities. Approval to proceed was given by Newmont Gold Company management in June 1987. Detailed engineering began in early July, followed immediately thereafter by procurement of major equipment components through various second hand sources. PROJECT DESIGN Keep It Simple In early August, Newmont Mining Corporation, parent company of Newmont Gold Company, became the takeover target of an "investor" group headed by T. Boone Pickens. Details of the ensuing events have been well documented by the press; suffice to say their impact on this project was material and required immediate flowsheet changes. Project design throughputs were increased to 1,000,000 DSTPY and 760,000 DSTPY for the heap leach and mill, respectively, in mid- September. These changes caused major project headaches as all general arrangement drawings had been approved and structural steel as well as concrete contracts were in place. Additionally, ground breaking was to commence in two weeks time! Rain project management assembled shortly after the announced changes, to devise an engineering and construction strategy capable of handling these new business conditions. The project had been justified using a gold price of $325 per ounce with a forecasted overall cash cost per ounce of $230. Hence, strict control of capital expenditures was necessary to maintain development economics. Mill start-up had also been moved forward one month, to August 1, 1988. To meet an already ambitious schedule, construction techniques needed to be simple and proven as most of the facilities were planned for erection during winter at a site with design criteria of -40F and 90 mile per hour winds. Perhaps the most critical factor requiring consideration was that of personnel. Newmont Gold's revised business plan called for corporate-wide production increases from 587,000 ounces per year in 1987, to 1,400,000 ounces by mid- 1989. Labor requirements were forecasted to grow from 900 employees to over 2,100. This fact, in combination with the rapid growth of Nevada's gold industry, led to the expectation that turnover of operating personnel would be extremely high. It was concluded that, to meet cost, time, and operational goals, the necessary strategy could be succinctly put - "Keep It Simple." Mining/Metallurgical Factors The Rain deposit consists of three interconnecting mineable shapes with host rocks ranging from 90%+ barite to a highly silicified jasperoid. Due to a limited number of mining faces in the first two years, in-pit blending

Jan 1, 1990

By Feng Liu

"With seven new applications for plans of work for exploration in the international Seabed Area approved by the Council during its twentieth session of the International Seabed Authority, 26 total approvals have been made by the Council up to date. Among them, three contracts were made with COMRA. On 8 August 2014, China Minmetals Corporation submitted another application to the Authority for approval of a plan of work for exploration for polymetallic nodules in the Area, which is also sponsored by the Government of the People’s Republic of China.China is one of the main contributors to the international seabed regime. The Presentation will describe China’s activities in the Area, such as exploration, technology development, environmental protection and policy making.JIAOLONG is a submersible with capacity of 7000 meters. JIAOLONG’s sea trials were carefully made in 4 years, from 2009 through 2012 and it successfully dove to a depth of 7062m in June 2012 at Mariana trench. A so called "Test Application Phase" started thereafter, and is planned to last for 3-4 years. Two cruises and 4 legs have already been made since then. A wide-range of findings were obtained during dives in South China Sea, and in COMRA’s Exploration Contract Areas for polymetallic nodules and cobalt-rich ferromanganese crusts. This presentation will reveal the colorful findings."

Sep 1, 2014

By Perry M. Jones

An important operational and environ-mental concern associated with in situ leaching activity is the balance between solution injection and recovery. Solution balance is an important indicator of the capability of a particular in situ hydrologic design to efficiently and effectively control and distribute leach solution within the target ore zone. The Bureau of Mines is investigating the factors that affect solution balance in an unsaturated ore deposit, as part of ongoing in situ leaching hydrologic investigations at the Cyprus Casa Grande Mine. Flow conditions in 58 injection and recovery wells at the Casa Grande In Situ Leaching Test Facility were monitored daily over an 18 month period. Changes in the balance between injection and recovery occurring during this period were evaluated using analytical and statistical methods. The results permit estimation of solution distribution and the volume of solution stored in microfractures and interstitial pore spaces within the deposit following 18 months of leaching. Approximately half of the difference between well injection and well recovery can be accounted for by solution movement through macrofractures into nearby drifts. Estimates of solution storage within the ore deposit at the end of 18 months of leaching range from 3.5 to 6.9 pet. of injected solution. These results also suggest that 13 to 26 pet. of the fracture/interstitial pore space in the deposit was saturated with solution after 18 months of leaching.

Jan 1, 1991

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), the authors showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/tonne of REEs occur in AMD and AMDp respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. Geospatial analysis identified a total resource of 340 tonnes stored at the 141 sites sampled in this study. While this analysis did not quantify the basin-wide REE inventory, it does indicate the impact that processing cut-off grades will have on the overall AMDp resource base.

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), the authors showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/tonne of REEs occur in AMD and AMDp respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. Geospatial analysis identified a total resource of 340 tonnes stored at the 141 sites sampled in this study. While this analysis did not quantify the basin-wide REE inventory, it does indicate the impact that processing cut-off grades will have on the overall AMDp resource base.

By Donald W. Gentry

This paper presents some of the results of a rock mechanics in¬strumentation program designed for, and implemented at, longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam and immediately below the coal seam. Longwall test panel 411 had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft). The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) al¬though it ranges from 73-134 m (240 - 440 ft). Roof support at the face was provided by Hemscheidt shields. These shield-type supports weigh 11.4 metric tons each.

Jan 1, 1977