Search Documents

By M. I. Brittan

A technique has been developed that analyzes routine mill operating data to determine the key operating parameters responsible for gold losses to tails. These parameters represent the prime operating variables having a dominant effect on gold recovery. The technique quantifies these effects for the specific plant being analyzed, providing a tool to optimize recovery and costs and so enhance the mine?s cash flow. The quantitative relationships generated will be different for each ore and plant: every case is site-specific and has to be treated on its merits. Examples are provided to illustrate the considerable metallurgical and financial benefits which can be realized from optimization. The examples are taken from case studies of mills in four major gold mining districts of the world.

Jan 1, 2010

By S. S. SHINDE, P. C. JIKAR, N. B. DHOKEY

Mill scale is an oxide waste product of the steel mills, which contains around 70% iron and other allied impurities. In the present context, a dynamic prototype counter current reactor (CCR) has been used for experimentation and simulation of particle bed by using discrete element method (DEM). Mill scale was pulverized to ASTM mesh range 140 (106 μm)/ + 270 (53 μm), and then it was oxidized in CCR to make single oxide Fe2O3 phase by maintaining required thermodynamic conditions such as pure oxygen at 1100 °C. Then this oxidized powder was subjected to reduction reaction in CCR having gas mixture ( H2:N2) ratio of 1:4 at 875 ± 5 °C for filling degree (fd) and reactor revolution (ω) ranging from 5.38 to 16.14% and 2 to 5 rpm, respectively. A creeping fluid flow condition (Re ˂ 1) and natural heat convection (Gr/Re2 ˃˃ 1) has been maintained while undergoing solid–gas reaction. Besides particle bed behavior has been quantified by Froude number (Fr) for the optimum operating window. The simulation was validated by the experimental results of reactor reaction product by X-ray diffraction (XRD) and scanning electron microscope (SEM) images. Prevailing heat transfer mechanism and reduction reaction mechanism has been established for solid–gas counter current conditions.

Nov 22, 2021

By Omar A. Muhtadi

Brohm Mining Corporation, in conjunction with Geobiotics, Inc. has nearly completed a pilot heap biooxidation test on sulfidic ore from the Gilt Edge Mine near Rapid City, South Dakota. Some results from the pilot testing have shown the correlation between the extent of biooxidation and the increase in cyanide gold recovery seen in the laboratory. Bench scale testing showed approximately a 1: 1 correspondence between percent biooxidation and percentage increase in gold recovery. The economics of large scale biooxidation were also evaluated in terms of increased gold recovery versus the time and cost of biooxidation. In the pilot test, the rate of biooxidation became limited by the acid water neutralization system. Later in the test, measures were taken to overcome this problem. Results from bench scale column bioleach testing showed that the Gilt Edge sulfide ore is quite amenable to biooxidation with a substantial increase in gold recovery with just partial biooxidation. Direct cyanide gold recovery of 51 % on ore crushed to -3/8" was enhanced to 82-85% after oxidation of37% of the sulfide as measured by iron. Laboratory experiments also showed that the slow rate of biooxidation of this ore could be accelerated by removal of metal sulfate build up from the leach liquor. The combination of these normally non-toxic metals became inhibitory to biooxidation if not removed by the neutralization circuit.

Jan 1, 1995

By Jack Bedder

"Editor’s note: We would like to thank those who make this annual issue possible. A special thank you goes out to the industrial minerals annual review editor, to the Industrial Minerals & Aggregates Division Technical Committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Ebrahim K. Tarshizi, member SME, of Michigan Tech, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include: • Hyunjung Kim, member SME, of Chonbuk National University, agricultural materials.• Xihui Yin, member SME, of Kemira, ceramics and refractory materials.• Nikhil Gupta, member SME, of Virginia Tech, chemical raw materials.• Jasson Giddens and Swadhin Saurabh, members SME, of Oil Dri Corp of America and Mill Creek Engineering, respectively, chemical raw materials.• Snehamoy Chatterjee, member SME, of the Michigan Tech.• LeDeana Roberts and Shubham Verma, members SME, of Imerys and U.S. Oil Sands, respectively, fillers and pigments.• Thomas Hilderbrand and Kaiwu Huang, members SME, of Thiele Kaolin Co. and Virginia Tech, respectively, sorbents, filters and process aids.• Rhaghav Dubey and Edgar Blanco, members SME, of Outotec and FL Smidth, respectively, specialty mineralsAntimony generally occurs along with gold, lead, copper and silver. There are more than 100 antimony minerals, although the sulfide mineral stibnite is the main one.Antimony enters the supply chain either as a result of mining (primary production) or recycling (secondary production). China has by far the largest antimony resources and is, as a result, the world’s center for antimony mine production. In 2016, it accounted for more than three quarters of the global mine supply out of a world production figure of 130 kt (143,000 st), according to the U.S. Geological Survey. The biggest, and most high-grade deposits are found in southern China, with the largest mines located in Hunan, Guangxi and Yunnan provinces. Tajikistan, Russia, Australia and Bolivia are the largest mine producers outside China. A new antimony project in Oman made progress in 2016, producing first metal in April 2016 in test facilities, and then ordered three furnaces for a 26 kt/a (28,600 stpy) antimony metal and oxide smelter that is due on stream in late 2017.Antimony ingot production is not as widespread as is antimony mine production, owing to the high levels of pollution that are associated with antimony smelting. It is for this reason that smelting has been largely confined to China and other Asian countries, where environmental legislation is less stringent.Antimony oxide production is undertaken on four continents with China being the biggest producer. There is also a considerable amount of oxide production in Europe — which relies on imported feedstock, mostly from China. Antimony also enters the supply chain through recycling. Lead containing antimony is produced in a number of countries, mainly in secondary lead smelters. Typically, a blast furnace charge containing used or discarded battery plates, type metal or bearing metal is reduced to lead bullion, which is refined in reverberatory furnaces and melting pots. In the main, the antimony recovered is consumed in metallurgical applications. China was the biggest secondary antimony producer in 2016, and accounted for 25 retardants and lead-acid batteries. Flame retardants accounted for roughly 50 percent of consumption in 2016 with batteries representing about 25 percent. Other end uses include plastics and heat stabilizers, ceramics and glass and a variety of metallurgical applications. Demand has been sluggish since the global financial crisis, mostly because key markets failed to recover strongly from the downturn, particularly in Europe."

Jan 7, 2017

It had been more than a decade since this many booths were occupied at an SME Annual Meeting, but at the 2010 meeting in Phoenix, AZ 630 booths were sold to 470 vendors from the entire spectrum of the mining and minerals industry. Exhibitors such as Metso, FLSmidth, West-Tech, ABB, NIOSH, Eriez and Resource West took their usual prominent places on the exhibit floor and were joined by newcomers such as tunnel boring machine manufacturer Herrenknecht AG, Frontier Kemper, the International Society of Explosive Engineers and more than 100 other first-time exhibitors. On the floor, one could find everything from a new pair of boots to a new career in the recruitment pavilion where some of the biggest companies in mining (Barrick Gold, Freeport-McMoRan, Newmont Mining, etc..) set up shop. The following is a look at some of the companies and products that were on display at the 2010 meeting. For information about displaying at the 2011 annual meeting in Denver, CO, Feb. 27 to March 2, contact exhibits@smenet.org.

May 1, 2010

By E. O. Mixon, Jack D. Kennedy

INTRODUCTION This contract is the most northerly portion of the Metropolitan Sanitary District of Greater Chicago's Tunnel and Reservoir Plan. (TARP) The project begins at Addison Street in Chicago and proceeds northerly approximately ten miles to end at Wilmette Harbor and Lake Michigan. The project which consists of 2 work shafts, 32 drop shafts, 7.322 km (24,020 ft.) of 6.7 m (22 ft.) diameter circular rock tunnel, 8.458 km (27,750 ft.) of 9.2 m (30 ft.) diameter circular rock tunnel and miscellaneous rock bolting and grouting, was bid for a total cost of $63,140,480. The tunnel invert elevation varies from 65.5 m (215 ft.) to 77.4 m (254 ft.) below the ground surface, which places the tunnel in a rock formation of dolomite limestone. At the tunnel invert, the unconfined compressive strength of the limestone varies from 96 MPa (14,000 psi) to 152 MPa (22,000 psi). The 6.7 (22 ft.) diameter tunnel required the mining of 10.9 cu m. (14.2 cu yd.) of rock per lineal foot of tunnel while the 9.2 m (30 ft.) diameter tunnel required the mining of 20.1 cu m (26.3 cu yd.) of rock per lineal foot of tunnel. The total cubic meters of rock required to be excavated from both tunnels was 818,821 cu m (1,070,978 cu yd.). All of this will be mined by tunnel boring machines (TBM). These tunnels were not to be lined with concrete. The thirty two drop shafts have upper portions that are cylindrical in the overburden and rock sections. They were divided into two groups, depending on diameter, with a different construction method for each group. The first group consisted of twenty three of the

Jan 1, 1979

By Anna Kate Miller, James J. Brady, Hamza Jaffal, Ritika Sangroya, Chadi El Mohtar, Wing Shun Kwan

"The design of an appropriate pre-grouting program can be the difference between a successful tunnel construction and an expensive on-the-go repair. However, current grout design relies heavily on rulesof- thumb and outdated charts. The geotechnical investigation is rarely targeted towards grouting design and the final grouting decisions are made based on fines content or soil classification. The current paper presents an experimental study performed to determine the optimal grout for a tunnel in soft ground below the ground water table (GWT). The testing program consisted of sieve analysis and undrained static triaxial tests on reconstituted sonic samples. Rheological tests were used to compare the different grout mixes and identify best candidates before performing one-dimensional permeation tests. Pressure and volume measurements during the permeation tests, along with the unconfined compression strength results on the permeated soils, helped evaluate the filtration potential for the different grouts and select the optimal grout.INTRODUCTIONConstruction of the Millwoods Double Barrel Replacement Project commenced in 2009 and was expected to be completed by 2015. To facilitate ongoing city development in south Edmonton, the City implemented construction of a major sanitary trunk network along 91st Street and 30th Avenue. The project involved the design and construction of approximately 1.2 miles (2 km) of 7.8-ft (2,400 mm) sanitary tunnel and 2.1 miles (3.4 km) of 11.5-ft. (3,500 mm) and 9.5-ft. (2,900 mm) storm tunnel. Part of the project also involved the conversion of the existing double barrel storm and sanitary trunk to full sanitary service, and reconnecting the local storm sewers from the double barrel pipe to the new storm tunnel. The tunnels range in depth from 26-ft. (8 m) to 115-ft. (35 m) and are being installed using a one pass system with precast concrete segmental liners."

Jan 1, 2016

By J. W. Shield

Refractory sulfide flotation or gravity gold concentrates are coated onto a sized support matrix and placed in a heap configuration for biooxidation. The surface coating is typically less than 0.05 in. thick and the support matrix is preferably composed of 0.375 to 0.75 in. diameter material. The exposed thin coating of sulfides reduces biooxidation rate limitations due to oxygen mass transfer. The large spaces between matrix particles reduce resistance to fluid percolation and aeration in the heap. The capital and operating costs for this biooxidation configuration are significantly less than for concentrate biooxidation in stirred tanks. After 30 to 90 days of biooxidation, sub- sequent gold recoveries exceed those seen in whole ore heap biooxidation and are comparable to recoveries obtained from stirred tank biooxidation processes. Results from laboratory and pilot testing indicate that this technology is a viable alternative for pretreating sulfide refractory gold ores.

Jan 1, 1997

By J. Sanko

When faced with the task of designing a process control system the control engineer must consider the following: 1. The type of process to be controlled and the manner in which the process must be controlled (the algorithm). 2. The type of equipment to be used to implement the control system. 3. A means of describing the control system for use in the following areas: a. Project engineering. b. Procurement of the control system equipment. c. Plant startup. d. Operator training and reference.

Jan 1, 1981

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals dore' from ores, principally silver bearing with associated gold co-products. In late 1995 a new orebody was commissioned, the Stone Cabin orebody, and the site began a phased shift from silver dominance to gold dominance in terms of precious metals revenue. The Knelson Concentrator was selected to remove gold from a portion of the cyclone underflow stream in the grinding circuit. This paper describes the development of the flow sheet, specific mineralogical impacts on Knelson product and downstream materials, and impacts on mine/mill grade reconciliation.

Jan 1, 1997

By P. M. Soupios

A near geophysical surface investigation of a landfill area close to the Hania city, in Crete Island, Greece, was conducted as inextricable phase of a preliminary geotechnical, geological and hydrogeological study of the area under investigation. Electrical Resistivity Tomography (ERT), one of the most promising prospecting techniques mainly concerning its effective contribution to resolve several environmental problems, was applied for the geophysical modelling. ERT is a robust imaging method the theory and implementation of which are well documented in geophysical research literature. The survey site is located in Akrotirion Peninsula, about 7km east of Hania city in Crete I. The geological setting comprises Trypalion limestones, marly limestones and a clayed weathered layer. Cavities are also identified at various scales which are recent tectono-karstic voids resulted from the combined actions of karstic erosion and tectonic stress on the Trypalion limestones where they are located. Due to the above-mentioned geological singularity and in the light of the requirement for an environmentally safe construction of the landfill, an ERT survey was carried out by deploying the dipole?dipole electrode configuration. Specifically, seven geoelectrical tomographies were conducted reaching the prospecting depth of 36m. The resulted images conduced, a) to overcome geotechnical problems, b) to plan the future sites for waste disposal and c) to reliably estimate the thickness of the already deposited wastes.

Jan 1, 2005

By Joseph W. Johnson

General Electric introduced electric drive systems on 85 ton Off-Highway mining trucks in the early sixties. Due to favorable economics, trucks have increased in size to handle larger payloads. Series Motorized Wheel systems were developed to meet this demand. When the technology was available, General Electric switched from use of Series motors to separately excited motors with the added benefits of static exciters and simplified control. Over 20 years of electric drive experience have been incorporated in the STATEX drive systems, which covers truck sizes from 85 to 220 tons. This paper traces the drive system developments from the early stages to the present and takes a look at what's ahead.

Jan 1, 1983

By L. L. M. Kadnuck

The U. S. Bureau of Mines studied the suitability of using flexible tendon cable supports as secondary roof supports at a western coal mine. The supports were installed in longwall tailgate entries and grouted into the mine roof. This paper quantifies how the use of cable supports can improve ventilation in underground airways. A mine ventilation simulator was used to model the changes in airway resistance and airflow and show potential for further ventilation improvements when cable supports are used. Model results indicated that cable support use translated to savings in air pressure around the longwall panel and increased airflow at the longwall face.

Jan 1, 1994

By R. L. Summers

The tremendous engineering advances occurring during this past century are very evident within the boundaries of the Anthracite Section of AIME. The Steelton plant of Bethlehem Steel Corporation, located along the Susquehanna River just east of the Commonwealth's capital at Harrisburg, for more than 105 years has experienced a most dynamic life which has paralleled America's industrial growth. (Figure 1) In June 1865, just after the Civil War, a group of men met to organize the Pennsylvania Steel Company. The war had brought into sharp focus the vital importance of the railroads to the country's expansion. Until that time wrought iron rails were used, and the replacing of track after only several months wear had become an almost unbearable cost. The spirit of free, competitive enterprise and the prospects of a lucrative market compelled these men to form that first Pennsylvania Steel Company and to develop better rail products. They issued the following statement: "...our desire to free ourselves from dependence upon a foreign market (has) led to the organization of the Pennsylvania Steel Company, and the parties who have connected themselves with it are determined to produce upon American soil all the principal manufactures of steel that are now, at such a serious cost for freight, commission, insurance, exchange, duty, etc., and often, with so much delay and uncertainty, imported from abroad. (We) are preparing to establish near the consumer, works at which articles of accustomed pattern will be promptly produced, and from the

Jan 1, 1971

By P. T. Bissert, L. Yan, M. D. Klein

"Since 2008, the U.S. Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines (MSHA, 2008). MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. In its 2006 report, the West Virginia Mine Safety Technology Task Force (2006) recommended an apparent temperature limit of 35 °C (95 °F) for RAs. In Title 30 Code of Federal Regulations Part 7.504, or 30 CFR 7.504, MSHA specifies a maximum apparent temperature of 35 °C (95 °F) inside an occupied RA (MSHA, 2016). The apparent temperature is calculated using both air temperature and relative humidity (Steadman, 1979).Calculations can be used to deter-mine if the air within an occupied RA will reach the apparent temperature limit. In these calculations, the mine temperature could be assumed to re-main constant. With this assumption, the effects of the mine strata thermal mass and thermal conductivity on the heat buildup in an RA are ignored. Re-search conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) shows that the mine air and strata temperatures surrounding an RA increase when subjected to the heat of an occupied RA (Yantek, 2014). Thus, calculations performed with the assumption that the mine temperature is constant would underpredict the resulting dry-bulb temperature and apparent temperature for a given RA occupancy. The mine air temperature has been used as the basis for RA temperature calculations. However, there has been no research to confirm that the mine air temperature is the appropriate basis."

Apr 1, 2017

By R. L. Grayson

In 1995, Congress abolished the Bureau of Mines in the Department of Interior but preserved the safety and health research functions being performed at the Pittsburgh and Spokane Research Centers. These functions were transitionally housed in the Department of Energy before permanently merging with the National Institute for Occupational Safety and Health (NIOSH), Department of Health and Human Services, in October 1996. Since the merger of the former Bureau with NIOSH, there has been an active evaluation of ongoing research activities, significant interaction with stakeholders, and the development of a process leading to "data informed" priority setting. This presentation will review current surveillance information concerning the level of injury and disease from mining work and will discuss how research priorities are evolving to improve the contribution of research to the prevention of injury and disease.

Jan 1, 1998

By Robert E. Gray

The vat leaching operation at the Yerington Mine was started in October, 1953. The original plant facilities consisted of primary and secondary crushing, eight leaching vats, precipitation launders, sulfuric acid plant and the necessary maintenance, warehouse and administrative facilities. By 1961, 35,000,000 tons of oxide ore had been removed from the mine exposing the underlying sulfide ore body. A 5,000 ton per day concentrator was constructed and put into operation to treat the sulfide ore in November, 1961. The original crushing plants were used for both oxide and sulfide ores. By adding a third crushing shift for six days per week, the treated ore was increased from 12,000 to 17,000 tons per day. To balance the oxide and sulfide ore reserves, the concentrator was expanded to 13,500 tons per day in 1967. Again, no additional crushing facilities were added. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to 9,000 tons per day. Instead, the addition of two crushing shifts per week, and improved operating procedures, increased the treated ore to 26,500 tons per day, 13,000 tons to the vat leaching and 13,500 tons to the concentrator.

Jan 1, 1975

By R. A. Jankowski

The U.S. Bureau of Mines has conducted a study to identify the sources of respirable dust and appropriate dust controls applicable to today's high tonnage longwall faces. The primary source of respirable dust identified is the cutting action of the shearer; however, the pct contribution of dust from coal transport through the stageloader/crusher was significant. This was primarily due to the high rate of mining, requiring rapid and constant coal transport. Techniques implemented for the control of shearer-generated dust included high drum water flow rates, deep cutting, shearer-clearer-type external water spray systems, and radio-remote control. The high water flow rates, and an enclosed stageloader with scrubber, were used to control dust during coal transport. No novel or effective control technology exists to control dust during support advance. Administrative controls for dust avoidance, and manual and batch-activated electro-hydraulic control systems were used to keep support movers out of the dust generated during support advance.

Jan 1, 1990

By Bo Hyun Kim, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health have tested the finite element code, UT3PC, with LaModel to evaluate their results using know case studies. The purpose of the testing was to demonstrate the usefulness and limitations of these programs in evaluating mine layout design. Both of these software packages are simple to use and free for public download. Their use by mine engineers, along with other tools, such as empirical methods, can enhance the assessment of a mine layout design. LaModel can model mining layout on a mine scale or, at least, on a multiple-panel scale. However, this software has limitations in calibrating to conditions at many coal mines in the western United States. The UT3PC software models smaller parts of a mine and is used to evaluate the design of pillars, shafts, or drifts; but the software calculates all components of the stress tensor and provides stresses, displacements, and safety factors throughout the model volume. The two codes are used to evaluate design of one known case, and UT3PC is used to evaluate another case. The results and approaches demonstrated in the testing are intended to aid mine engineers in evaluating site-specific problems and to show that these tools can provide useful information to the mine engineer in evaluating mine layout design.

Jul 1, 2023

By QINGXIANG CAI, Lin Li, PENG LIU, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, YONGLI ZHOU

The concept of green mining is to improve the mining industry in a holistic way so that it is safe, efficient, and environmentally sustainable. The purpose of this study was to develop an evaluation index system of green surface mining based on the theory of green grades. The evaluation model is comprised of three attributes (safety, efficiency, and environment), nine criteria, and 35 indicators. The fuzzy comprehensive evaluation method was used to determine the weights of indicators by taking into consideration degree centrality, closeness centrality, and betweenness centrality. Findings indicate that the environment is the most critical aspect of green surface mining, followed by efficiency and safety. The top five ranked green mining success indicators were the application of new technology, starting-off-rate of equipment, science and technology input to total investment, the number of accidents (decreased), and the production (increased). It was observed that more improvements are needed to overcome water, air, waste, and sound pollution. Attention should also be paid to land reclamation and post-mining land uses, which are key factors in green mining. The proposed model can be applied to evaluate and improve the level of green surface mining in other regions. This study provides a tool for decision-makers that can offer technical assistance to green mining.

May 26, 2020