Search Documents

By M. W. Harmer

Laboratory test work, pilot plant testing and plant experience with wet, fine mesh screens is discussed. High frequency, low amplitude, fine mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with 'hot ferric chloride to remove Pb and Cu contaminates before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1990

By David E. Nicholas

Design of underground openings is becoming more critical as the mine deposits become lower in grade, initial investments increase, ore depth increases, additional safety regulations come into law, and increased ore recovery is required for conservation of minerals. Stability of these openings is dependent on the strength of the rock mass and the pre-mine stress field. The rock mass is composed of solid blocks of rock (rock sub- stance) and structural features (faults, joints, bedding, etc.). Methods of testing the rock mass strength are improving and be- coming more common, however it is difficult to justify the high cost of large scale testing for an initial mine design. An alternative to testing the rock mass is to measure the rock substance and the structural features separately, and then combine them to estimate the rock mass strength. The rock mass strength will vary depending on the orientation of the opening with respect to the structural features. The other factor affecting the stability of underground open- ings is the pre-mine stress field. Methods are available to measure "directly" the pre-mine stress in competent and relatively massive rock. These methods are costly to employ, therefore, they may not be justified in an initial study. The pre-mine stress field can be estimated based on the structural relationships formed from past tectonic events.

Jan 1, 1976

By Bahram Sameit

Blast engineers have been taking advantage of image-based rock fragmentation analysis methods for the past three decades to estimate rock size distributions. These methods utilize a range of image segmentation techniques, from manual to fully-automated, to delineate the edges of rocks in images. Rock delineation results are then converted to physical rock sizes (and percentage passing curves) by scaling the image pixels to correspond to physical measurements. The size scaling process is critical for acquiring physical measurements, but specifc to the limitations of different applications. This article starts by presenting a shovel bucket-based fragmentation analysis system, where scaling is done using the known width of the shovel bucket within the image. It will then describe methods that use pictures captured by digital cameras with scaling reference objects in the view. Finally, the article presents a method that uses three-dimensional imaging to capture images without the need for scaling reference objects.

By Philip Morey

Large scale surface coal mining will be required to fill future energy demand in the United States. In realization of this long-term commitment to coal resources, the U.S. Energy Re-search and Development Administration sponsored a study to determine the costs and problems of large-scale surface coal mining. As a result of this study a series of computer models were developed that can be used by government and industry to: 1) facilitate mine design and equipment selection, 2) provide detailed analyses of mining and processing costs. Two types of models were developed: detailed simulation models, which provide detailed information on mining systems and equipment to assist in mine design and equipment selection1 and broad models, which provide a first-order evaluation of deposits and new ventures for an entire mining complex. The complete model series permits examination of surface coal mining under a variety of terrain conditions. Six different mining methods were analyzed and documented during the overall project: 1) Area stripping with draglines, 2) Area stripping with draglines, extended bench, 3) Contour stripping with draglines, 4) Area stripping with shovels (loaders) and trucks, 5) Mountain top removal with shovels (loaders) and trucks, 6) Multiple dipping seam mining with shovels (loaders) and trucks. Each major operation in the coal mining pro-cess is represented in these models so that the best methods and equipment may be selected and 50 that the impact of such selection will be reflected in estimates of capital investment, operating costs, and coal price. Individual models allow the user to separately analyze overburden removal, overburden drilling and blasting, coal drilling and blasting, coal loading and hauling, coal preparation and handling, land reclamation, and premining, facilities, and administrative expenses. Because it is impossible to cover all the models in this paper, only the detailed simulation models representative of the technique "area stripping with draglines," are described. The Fort Union Strippable Coal Resource Region, one of eight test cases, is used as an example to describe the models.

Jan 1, 1978

By Robert G. Lundquist

REAM (for Rapid Excavation And Mining) is a method of rock fragmentation by high-velocity projectile impact developed by Physics International Company. This paper reports the results of field testing over the last two years. The success of the method is based on the fact that the amount of rock broken per shot scales nonlinearly with projectile impact energy. Thus, high energy impact yields spectacularly low specific energies for rock breakage. The field work reported used 90- and 105-mm military guns to accelerate 8-1/2 and 10-pound concrete and steel projectiles to velocities of 5000 to 5500 fps. All tests were performed in a competent 25,000 psi granodiorite at Hope Valley, California. During the first year of field testing 26 feet of 13-foot-diameter tunnel were produced with the 105-mm gun. The first 20 feet of this tunnel were line-drilled to aid in producing a stable portal. During the second year the tunnel was extended an additional 29 feet using the 90-mm gun. The 55-foot tunnel was produced by 590 shots. Between 1-1/4 and 1-1/2 tons of granite were broken by each shot. A silenced 90-mm gun was placed underground and the tunnel portal closed with a steel barrier. Overpressures of less than 1 psi were measured on the inside of the barrier, corresponding to an impulse noise of about 170 db. The muck produced was similar to drill and blast muck. Overbreak and ground support problems appeared to be less than with drill and blast. The contour of the tunnel was easily controlled using the 90-mm gun; the tests were also conducted using a 57-mm gun for trimming. Projections indicate that advance rates with REAM will be three to seven times faster than drill and blast, at less than two-thirds the cost. This is based on the development of a fully integrated continuous system and an inexpensive propellant giving a total expendables cost of less than $3 per shot. Other applications of the REAM technology are found in secondary breakage for open pit mining, in drilling large diameter holes, and in underground mining for longwall mining, overhand stoping, and raising.

Jan 1, 1974

By Ken Goering, Steve Kral, William Gleason

"Once every four years, the global mining industry gathers in Las Vegas, NV for MINExpo International. According to the show’s organizer, The National Mining Association (NMA), about 44,000 people attended the three-day show from Sept. 26-29. It was a show that featured the latest and greatest in equipment and technology. It also served as the backdrop for a snapshot of the state of the industry and while the picture of a global industry is never completely clear at any one time, one thing that is evident is technology has become a major force in the way mining is done.Had it not been for the awe-inspiring “iron” that was on the show floor in the form of haul trucks and shovels weighing hundreds of tons, one could be forgiven for thinking that they were at the Consumer Electronics Show. From training simulators designed to give a realistic experience of operating mining equipment to virtual reality technology that can take the user into the depths of an underground mine or the middle of a mapped ore deposit, an overriding theme of MINExpo 2016 was that the mining industry is connected like never before.In the north hall of the Las Vegas Convention Center was the GE Mining booth that was designed to showcase its efforts to help create a mine that will be connected from the front office to the face of the underground wall or bottom of the openpit. GE Mining called its booth a digital mine, and it included a suite of technologies that can improve performance, reliability, safety and operations. GE Mining said it views each mine as a mini-city, requiring power, water and transportation. Intelligent, real-time monitoring across the mine allows operators to make data-driven decisions that improve equipment reliability and optimize mine operations for substantial savings. And GE Mining was just one of many exhibitors showing off software that allows various types of equipment to communicate. Its booth sat in the shadow of the Komatsu booth with its new 360-t (400-st) 980E-4 haul truck that included GE’s 360-t (400-st) electric wheel motor. This is just one example of how technology is connecting machines, operations and people around the world and how mining is moving forward."

Dec 1, 2016

Mineral Resource Technologies(MRT) and Michigan Technological University (MTU)finalized an agreement that permits MRT to offer an advanced carbon removal technology process for coal fly ash from an ash residue generated by utilities. The agreement encompasses the dominant existing US patents using a wet process for fly ash enhancement. The wet process for coal beneficiation of a fly ash product involves four steps. First, a slurry mixture is formed of a fly ash material and a liquid. Second, gravity is used to separate and collect a first-material fraction of the fly ash, having a density less than the liquid. This is done by skimming off the flotation slurry material.

Jan 1, 1996

By Michael Casson

With the mining industry changing rapidly due to mergers, acquisitions and fluctuating market pricing, today?s market for coal, minerals, ores and aggregates demands electrical apparatus that perform every time with maximum efficiency and with consideration for personnel safety. This is especially true in existing mining operations where every payload counts. Draglines are the workhorses of surface mining operations, and reliable and efficient operation is absolutely critical to success. However, the inherent disadvantages of using dc motors and motor-generator (MG) sets can significantly impact productivity and return on investment (ROI).

Jan 1, 2013

By V. T. McLemore

"Production of industrial minerals remains important to the rural economy of New Mexico. In 2014, some 240 mines were registered in New Mexico, including 25 industrial mineral operations and 189 aggregate operations. New Mexico leads domestic production of potash, perlite, zeolite, and travertine. Other production includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica, and decorative stone. New Mexico has potential for additional production of industrial minerals. One company is exploring for garnet. Cretaceous black sandstones in the San Juan Basin have drawn interest for titanium, rare earth elements (REE), and zircon. Other REE deposits are being explored. REE-Th-U veins are found in the Gallinas, Capitan, and Cornudas Mountains and Laughlin Peak-Chico Hills. Recent exploration has occurred for beryllium in the San Mateo Mountains, Iron Mountain, and Victorio districts. Companies also are examining High-Ca limestone and High-Mg dolomite for potential development. Aggregate continues to be important in urban areas and along highways. INTRODUCTION Industrial minerals and rocks are literally the building blocks of our way of life and they are an exceptionally diverse and vital group of raw materials that underpin almost all aspects of human activity, infrastructure, and standard of living. Industrial minerals and rocks are used in the manufacture of many products, from ceramics to plastics and refractories to paper. Although industrial minerals permeate every aspect of daily life, their presence and their role are typically invisible. A widely used definition of industrial minerals and rocks is “any rock, mineral, or other naturally occurring substance of economic value, exclusive of metal ores, mineral fuels, and gemstones: one of the non-metallics” (Bates, 1975). This definition includes the important construction materials sector as well as specialized industrial minerals, but complex interactions between consumer industries produce a number of apparent anomalies to this definition. Some metals are included as industrial minerals because their use is industrial rather than as a metal. Sulfur is now predominantly extracted as a by-product of cleaning natural gas, one of the world's major energy fuels. Production of industrial minerals has been and remains important to the rural economy of New Mexico. Industrial minerals constitute nearly 40% of the more than $2.8 billion generated by mineral production in New Mexico in 2013 (Table 1, see APPENDIX). In 2015, some 240 mines were registered in New Mexico. This total includes 25 industrial mineral operations and 189 aggregate operations. New Mexico leads domestic production in potash, perlite, zeolite, and travertine. Other industrial minerals production from New Mexico includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica, and decorative stone. Additional production statistics are in Harben et al. (2008). Major industrial mineral districts are shown in Figure 1."

Jan 1, 2016

By Steven J. Schatzel, James Addis, K. Vaibhav Raj, Berk Tulu

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to enhance methane control and mine ventilation practices at coal mines, as a method to mitigate hazardous work conditions. NIOSH researchers conducted case studies to investigate the effectiveness of existing systems and improve performance to decrease the potential for unplanned or excessive methane emissions. At one mine, drainage was influenced by hydrofracking inefficiencies where two of the six wells showed good frack development. Methane content was variable, from 300 ft3/t to 600 ft3/t. This paper also summarizes overburden movement during undermining and the estimated quantities of gas transported to the mine using FLAC3D and CFD modeling. The findings from this research effort highlight considerations based on specific mine conditions that may also be applicable to most longwall mines utilizing methane control systems.

Feb 1, 2025

By J. A. Meech

An analysis of screen design options on the operating efficiency of secondary crushing plants has been conducted using a dynamic computer model. The model allows for the simulation of a wide variety of crushing circuits and can be run on either a microcomputer (IBM PC/XT) or a large time-sharing mainframe computer. Size reduction and separation characteristics of crushers and screens are based on standard manufacturer design and performance data. Input/output routines are available in tabular, alarm or strip chart recorder modes to facilitate operation of the program. A number of alternate circuit designs are compared to show the influence of surge capacity, screen size and area, screen deck location, and closed side crusher settings on the operation of a 10,000 ton per day plant. The program is currently in use at Queen's University to teach plant operations and control. It has potential to be a valuable tool for operator training.

Jan 1, 1985

By C. Y. Haas

Of all the industrial clay minerals, attapulgite probably enjoys the widest variety of applications. A review published over three years ago by Haden and Schwint (18) cited some 80 individual uses, a list which continues to grow. In its near half-century of commercial life, attapulgite has received a generous share of research study and patent development effort, both on the part of producers as well as consumers. This work has been divided between understanding the mineral's structure or properties and applying it to specific end-uses. Naturally, information gained from the former has pointed toward opportunities in the latter. References of particular significance are cited throughout the text. Attapulgite's variety of uses derives from the unique three-dimensional structure and needle-shaped particle form of this crystalline hydrated magnesium aluminum silicate. Its inherent colloidal and sorptive properties are well known, and distinguish it from its sister clay minerals. Attapulgite is characterized by its high surface area, porosity, sorptivity, and decolorizing power. Its slips or slurries are viscous and thixotropic, however, unlike bentonite are not flocculated by electrolytes. In Table I are compared the general properties of attapulgite, bentonite, and kaolin. The properties in Table I are documented in greater detail by the wealth of scientific literature which has been published on the composition (14)(15), structure (6)(16), surface (16)(4)(22)(24), adsorption (31)(4)(5)(25), rheology (10-11)(12)(13)(26)(27)(32), plasticity (30) (31), and chemistry (23)(3)(7) of attapulgite. Attapulgite is the principal mineral constituent (70 to 80%) of attapulgite clay as it is commercially produced in the Georgia-Florida area of the United States. As mined, this clay also contains 10 to 1S% montmorillonite, sepiolite, and other clays; 4 to 8% quartz, and 1 to 5% calcite or dolomite. (18) During processing, non-clay fractions are removed so that commercial products are enriched to 85 to 90% attapulgite. By wet processing (such as practiced in the

Jan 1, 1971

By E. Siami-Irdemoosa, S. R. Dindarloo

Ease of excavation or rippability, also called diggability or excavatibility, is a critical decision-making parameter in the selection of both the overburden removal method and the required equipment in surface mining and geotechnical engineering projects. The most widely used method of estimating rippability is rock mass classification. Although there are different classification schemes in the literature, all of them have the two major limitations of sharp transitions at class boundaries and subjective uncertainties in decision making. In this study, the decision trees method was employed as a classification tool for estimating ground rippability, using the four rock mass parameters of weathering degree, uniaxial compressive strength, joint spacing and bedding spacing. The results were compared with those of the widely used method of diggability index rating (DIR) and a fuzzy-based DIR. The problem of subjective uncertainty was resolved in the proposed decision trees method, as the tree rules were derived automatically from the training data sets. Compared with fuzzy-DIR, a decision tree classifier is simpler, needs less computational time and is more appreciable by industry practitioners. Nevertheless, the proposed method is not flawless and, similar to both the conventional and fuzzy DIR methods, yielded poor estimations in particular instances. The limitations of the three methods are discussed.

Jan 1, 2015

By K Martin, C. J. Nelsen, J. L. Schutz, S. R. Maynard

Investigations in the Ortiz Mountains have revealed the relationship of igneous activity and gold mineralization to the Tijeras-Canoncito Fault System (TCFS). The northeast-trending TCFS passes through the southeastern part of the Ortiz Mountains where its principal structure is the asymmetric Ortiz Graben. Several fault blocks, containing up to 305 m (1000 ft ) of Eocene Galisteo Formation, comprise the graben that has up to 1220 and 610 m (4000 and 2000 ft) of stratigraphic separation on its southeast and northwest sides, respectively. Intrusions in the Ortiz Mountains can be subdivided into two petrochemical types: an older calcalkaline suite and a younger alkaline suite. The calc-alkaline rocks are characterized by extensive sill, dike, and laccolithic bodies of latite-andesite intrusives and at least one younger (?) granodiorite stock at Candelaria Mountain. The alkaline rocks consist of a large nepheline-bearing augite-monzonite stock, a latite-porphyry hypabyssal plug, the Ortiz diatreme (vent breccia), and trachytic-latite dikes radial to the diatreme. K-Ar age determinations suggest the older suite to be 34 +/-2.2 million years while the younger alkaline rocks range from about 30 to 26 million years. Gold mineralization in the Ortiz Mountains occurs in five distinct environments: brecciapipes, skarns, veins, porphyry-like stockworks, and placers. Lode mineralization is associated with the alkaline suite of intrusive rocks postdating the Ortiz diatreme and predating most of the trachytic-latite radial dikes.

Jan 1, 1991

By T. C. Murray

An automatic control system was recently installed to insure the continuity of operation between the ship docking and ore handling facilities and the computerized conveyor-fed sintering plants and blast furnaces. Although the basic concept for material handling has not changed, many innovations including computer control have been implemented.

Jan 1, 1978

By E. A. Schmidt

In 1962, while investigating the tungsten potential in the Thompson Creek area for Union Carbide Corp., Henry T. Eyrich obtained anomalous concentrations of molybdenum (up to 19 ppm Mo) from stream sediment samples collected along Pat Hughes Creek, a tributary to Thompson Creek. Follow-up investigations by Eyrich during the same year disclosed the presence of a hydrothermally altered and molybdenite-bearing granitic exposure in the headwaters of Pat Hughes Creek about 2.4 km (1.5 miles) upstream from the sample point. The altered outcrop measured about 549 by 305 m (1800 by 1000 ft), contained abundant northwest-trending quartz veins locally with molybdenite, and was overlain and surrounded by the Challis volcanic extrusive sequence of mid-Tertiary age. Eyrich's subsequent soil and rock chip geochemical sampling program over the altered outcrop area showed a general increase in the molybdenum content to the northwest toward the postmineral Challis volcanic cover. Over a distance of about 305 m (1000 ft), values in the altered intrusive rock increased from less than 5 ppm Mo to over 600 ppm Mo, with aconcomitant intensity of the hydrothermal alteration pattern. Based on these geochemical results and on preliminar; megascopic hydrothermal alteration studies, Eyrich correctly concluded that the altered outcrop is an erosional window and that molybdenum mineralization of sufficient grade could exist beneath the Challis volcanic cover some distance further to the northwest. His recommendation to test the area of potential molybdenum mineralization with several drill holes was, however, declined by Union Carbide in 1962. The property remained unclaimed until 1967, when Eyrich joined Cyprus Mines Corp. Acting on Eyrich's recommendation, Cyprus immediately staked 26 lode mining claims to cover not only the altered intrusive outcrop, but also the northwest trend of mineralization where it projected beneath Challis volcanic rocks. Eleven of these claims are now patented.

Jan 1, 1991

By Gregg J. Hodges

The Stillwater Mining Company, a partnership of The Pittsburg & Midway Coal Mining Co. and Manville Corporation, began commercial production of flotation concentrates from the western hemispheres' only primary platinum palladium deposit at Nye, Montana in March 1937. In the fall of 1987 an integrated pilot plant testing campaign of electric furnace smelling and oxygen? blown converting confirmed the feasibility of further upgrading to semi? refined matte or 'white metal". In the summer of 1990 the production smelter was brought on-line at Columbus, Montana. This paper describes the technology transfer from the pilot to the production smelter. Emphasis is placed on flowsheet development and the scale factors between the test and production furnaces and gas cleaning plants. The metallurgical results of the pilot plant and of the early months of production of the commercial works are also compared.

Jan 1, 1991

By KOKOWSKI J., RUDZIŃSKI Ł.

The LUMINEOS network was established in 2013 to monitor mining-induced seismicity in Legnica-Głogów Copper District (LGCD), located in south-western Poland. Since the starting time, the network was improved and today consists of 17 seismometers and 10 accelerometers. Up to now, the strongest recorded earthquake in the region had Mw4.0. Both raw seismic data and earthquakes catalog for events recorded by the LUMINEOS network are fully open and available on the EPISODES platform (https://tcs.ah-epos.eu/#episode:LGCD). During the last 7 years, the network improvements gave us a possibility to increase location accuracy for shallow mining events. This accuracy is influenced by factors such as the configuration of seismic stations, noise level at seismic stations, and the influence of the velocity model. Here we encountered two main issues which are worth to discuss. The first one is the low detection threshold of two seismic stations and their significant impact on the location errors. The second one is the large uncertainty in the S-wave picking. Even though S-waves are not so clearly visible on seismograms, they are very helpful in the estimation of source location and strength of seismic events in the region. In our work, we present the history of LUMINEOS network and corresponding improvement on location accuracy as well as the influence of noisy stations on the error distribution and how it is connected with location results. We also investigate the effect of the S-wave phases and how they are related to the accuracy of the earthquakes locations in the network.

Apr 26, 2022

By ETHAN FUSTER, Richard Ray Jr, STEPHEN LEE

The abstract states that horizontally-mounted jet fans are commonly used to ventilate vehicular tunnels due to their space and cost savings compared to fully ducted systems. It highlights the successful use of vertically-mounted jet fans in exhaust ventilation shafts for a passenger rail overbuild in New York City. The paper compares shaft dimensions, jet fan placement, and measured airflows, also comparing these measurements to predictions from computational fluid dynamics (CFD) simulations.

Mar 16, 2022

By B. Samanta, S. Bandopadhyay

Ore grade modeling of a placer gold deposit is considered a challenging problem even today. Typically, gold-bearing deposits show extremely erratic and unpredictable grade variation. This is principally because of isolated occurrences of gold metal within a few high-grade pockets. Because of sporadic fluctuation of high-gold-grade distribution, the overall spatial continuity of the deposit becomes poor. This type of variation is often described by a lognormal or highly skewed frequency distribution, and the spatial continuity of the deposit is characteristically represented by a variogram model that exhibits a high nugget component. Further complicating the matter is the sparse availability of drillholes to capture such erratic variation. Due to the prohibitive cost of drilling, gold grade and reserve estimations are typically carried out using insufficient exploratory data. Use of a traditional estimation technique on limited data often produces an unreliable ore grade model. Kriging and its nonlinear variation, lognormal kriging, are frequently used in gold deposit modeling (Rendu, 1979; Journel, 1980); however, kriging is flawed by the smoothing effect. Moreover, though kriging is known to be globally unbiased, it is not free from conditional bias. As a result, if a deposit is modeled using the traditional kriging technique, a high-grade zone can be predicted to be a low-grade zone and vice versa. Predicting high grade as low grade results in a missed opportunity to exploit profitable ore. On the other hand, prediction of low-grade ore as high-grade ore might result in financial loss for a mining operation. Thus, the use of kriging for ore grade mapping of a gold deposit may not be recommended. Estimation techniques (including kriging) can produce an estimate with minimum error in a minimum-error variance sense. However, no matter which estimation technique is used for grade modeling of a highly erratic deposit like gold, the error margin is bound to be high. Therefore, any grade prediction made for an unknown location is associated with high uncertainty. Since various mine-planning operations, including derivation of grade tonnage curve, pit design and economic analysis of the deposit, are based on estimated grade rather than true grade, a mining project evaluation that depends upon estimation will be subject to considerable risk. Thus, the successful design of a mining project not only depends upon accurate grade estimates, but also upon accurate assessment of uncertainty, for predictive grade is equally important. Although the kriging standard deviation is used as an indicator of uncertainty for prediction, it is flawed by characteristics related to a data-independence property. This study, therefore, investigates the stochastic simulation technique of conditional simulation for ore grade modeling of a placer gold deposit at Nome, Alaska. It is expected that the research will provide a better solution to ore-grade deposit modeling than the kriging technique because (1) conditional simulation preserves spatial continuity as well as reproduces the data histogram, thus avoiding the smoothing problem; and (2) generation of multiple realizations helps to accurately quantify the uncertainty about grade values in the deposit.

Jan 1, 2009