Search Documents

By V. Rajaram

The Metropolitan Water Reclamation District of Greater Chicago (MWRD) imposed a no-blasting specification (blasting is restricted to the construction shaft and shaft bottom or boot) on the Deep Tunnel project in 1988. This was prompted by numerous complaints from the residents in the vicinity of the project, and controversies experienced on previous projects from blasting the rock overlying the tunnel. This paper will describe the methods utilized by two major contractors who are driving 20 km (12.5 of tunnel along with drilling over 36 shafts under this restrictive specification. The impacts on design, construction, schedule, cost, and the environment are detailed.

Jan 1, 1991

By David X. Zhang

This paper describes the results of using shear flocculation and flotation known as aggregative flotation technique for the enrichment of coal-derived char produced from mild gasification process. Aggregative flotation is a separation process which involves the use of suitable aggregating liquid under the action of high shear forces to render hydrophobic surface of coal-derived char particles to aggregate in an aqueous slurry. The fine carbonaceous particles are aggregated into larger floes while the impurities remain hydrophilic. In subsequent flotation process, the char aggregates are then separated from mineral matters by aeration in the flotation cell. The floatability of char aggregates and removal of mineral matters from chars are studied in a lab scale flotation column cell. The effect of various operating parameters on the aggregative flotation responses is presented. Emulsification of aggregating liquid using high intensity agitation and ultrasonic energy provides excellent aggregating liquid dispersion and increases selectivity for char aggregation. In subsequent flotation process, it results in significantly increasing the flotation rate of char aggregates. The microscopic examinations of bubble attachment to coal-derived char particles under various aggregating liquid dispersion levels were conducted by induction time measurement. The distributions of hydrophobicity of char particles and char aggregates prepared under various aggregating liquid dispersion techniques were measured by film flotation. The char particles prepared under high intensity emulsification attach at significantly faster rates to air bubble and with lower mean critical wetting surface tension than that of char with direct aggregating liquid addition. An interrelationship of increasing in flotation rate/combustible recovery with decreasing in induction time, mean critical wetting surface tension and dispersion of hydrophobicity on the char particles and char aggregates were obtained.

Jan 1, 1992

By Thomas F. Joyce

N L Industries, Inc., MacIntyre Development produces ilmenite and magnetite concentrates from its own open pit operation at Tahawus in New York's Adirondack Mountain region. The ilmenite concentrate is used within the company for the production of titanium dioxide pigments and the magnetite concentrate is sold to heavy media processors. Current production is from South Extension mine, loading by by six-yard Marion electric shovels into 85 ton Lectra Haul trucks. Bench heights are 44' and are drilled with a Robbins Rotary 9 7/8" diameter hole on 25' spacing for a yearly production of 3.4 million total tons of rock. The ore deposit occurs in veins dipping on the average at 40 degrees to the west. The ore body, which is divided into three zones, outcrops at surface and continues to depths of 800'. Zone 1 is a high grade band of thickness 150-200' with an Fe/Tio2 ratio of 2. Below this band is Zone 2, a low grade band of thickness 50-100' with an Fe/Tio2 ratio of 2 and beneath that seperated by a band of anorthosite is Zone 3, a high grade band of irregular thickness 50-450' with an Fe/Tio2 ratio of 1.6.

Jan 1, 1973

By Angelina Anani, Nathalie Risso, Carlos Olmos de Aguilera

The traditional approach to safety clearance monitoring and proper PPE usage in underground mines is time-consuming, costly, and susceptible to negligence. However, automated real-time monitoring can be implemented using computer vision-based approaches. This study aims to develop a system that provides timely information based on the automatic detection of proper PPE use and safety clearance in underground mines. Deep learning and a decentralized computing structure between the cloud and sensing devices (fog technology) are used. We hypothesize that a camera-based system can provide near real-time assessment of proper PPE use and verified clearance to access restricted areas in underground mines.

Jun 25, 2023

By Roger C. Wilmoth

The most common method of treating mine drainage to prevent water pollution consists of neutralization and aeration. This process removes the acidity, iron, aluminum, and some other heavy metals, but does not render a water suitable for domestic or industrial use because of the high dissolved solids, hardness, and sulfate in the treated water. The Environmental Protection Agency (EPA), has been sponsoring and conducting research since 1966 on the use of reverse osmosis (R.O.) for the treatment of mine drainage. This process has been found to be highly effective in the removal of nearly all the dissolved solids. In addition, since R.O. is a concentrating process, potentials for recovery of valuable heavy metals are possible. This paper is a review of the state-of-the-art on the treatment of mine drainage by reverse osmosis.

Jan 1, 1972

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By N. J. Keys

This paper concerns the development and application of a high throughput multi-stream photometric sorting machine developed for the South African gold mines. It is now believed that this sorter and its progeny may be found suitable for a large proportion of all possible sorting applications. A laser light source and sensitive photomultiplier are employed in a scanning system to detect light reflected from the surfaces of rocks passing through the sorting zone. Electronic circuitry then analyzes the photomultiplier signal, which represents the varying intensity of the reflected light, and produces control signals to actuate the appropriate valves of an array of air blast rejection devices to remove from the feed certain particles selected by the analyzing process. Typical throughput per machine ranges from 50 tons/hour for a-2 ½? + 1 ¼? feed to 200 tons/hour for -6" +2 ¾ " material.

Jan 1, 1974

By J. A. Holtkamp

Environmental regulation in Mexico has matured dramatically and effectively in the last decade. The gap between environmental regulation in the United States and Mexico is rapidly narrowing, so much so that it is no longer necessarily less burdensome to operate in Mexico from a regulatory perspective. This paper is intended to give a general overview of the system of environmental regulation in Mexico. The actual application of Mexican laws and regulations governing the environment to a specific operation will require a much more detailed review of the applicable environmental standards.

Jan 1, 1994

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014

By L. L. Damon

A geochemical study of cyanide neutralization processes was conducted at Brohm Mining Corporation to gain a better understanding of the leach pad behavior and to develop a simplified procedure to quantify the attainment of compliance with permitted cyanide neutralization criteria. Such attainment is a prerequisite for off-loading spent ore from the leach pad at the "load/unload" gold heap leach operation. The geochemical study program consisted of size fraction analyses and weak acid dissociable (wad) cyanide analyses for various sections of the spent ore from the actual leach pad. Further testwork included size fraction analyses and wad cyanide analyses on the ore from four 29 foot laboratory test columns which were leached and neutralized with different neutralization treatments in parallel with an actual active leach pad. Wad cyanide was analyzed daily on the neutralizing columns and various parameters were monitored weekly on the influents and effluents during the leach cycle and neutralization period. A comparison was made of neutralized effluent chemistry and porewater extraction fluids, as well as an analysis of the selective adsorption of cyanide on various particle size fractions.

Jan 1, 1992

By John J. Simmons

There is considerable interest in the iron and steel industry in the development of technologies that can reduce carbon dioxide emissions, as the iron and steel industry is the third largest producer of carbon emissions in the world, after automobiles and the power generation industry. The E-Iron Iron Nugget Making Process, invented by Dr. Komar Kawatra and Dr. Tim Eisele, provided a major breakthrough in the iron making process as the process uses biomass in the form of hard wood or soft wood as the reductant in the place of coal. Dr. Kawatra recognized that biomass is rich in both carbon monoxide and hydrogen, two important reducing agents. This resulted in initial experiments conducted by Dr. Kawatra and Dr. Eisele in the laboratories of the Chemical Engineering Department of Michigan Technological University (Michigan Tech) that prepared self-reducing pellets with wheat flour as the reductant and limestone/dolomite as the flux. Initial results were encouraging so they extended their work to include hardwood, which is in huge supply in the forests of Michigan and Minnesota, as the reductant. Dr. Kawatra has also applied the E-Iron Technology to other iron bearing minerals to produce pig iron grade iron nuggets. He used the E-Iron Process to convert red mud, a high iron waste product of the aluminum industry, into pig iron nuggets with the rare earth elements reporting to the slag. This work resulted in a patent with Dr. Kawatra and Dr. Michael Archambeau named as the inventors. Dr. Kawatra then extracted the rare earth elements as a separate high value bi-product using oxalic acid, which he produced from carbon dioxide. Dr. Kawatra also conducted a test program that produced pig iron nuggets from New Zealand beach sands. The vanadium in the beach sands was retained in the iron nuggets, recoverable as a valuable bi- product in a separate process. The titanium dioxide in the beach sands reported to the slag. This demonstrates the potential use of the E-Iron Process to convert the large ilmenite reserves in Northern Minnesota into pig iron and titanium dioxide. Another use of the E-Iron Process discovered by Dr. Kawatra was its ability to produce iron nuggets from manganiferous ores. Dr. Kawatra was able to direct the manganese into either the metal or slag by adjusting process temperature. The above discoveries are included in several patents that were assigned to Carbontec Energy. This presentation will only address the use of the E-Iron Process to produce pig iron nuggets from steel mill waste and un-pelletized, mid-grade iron ore. Carbontec Energy Corporation agreed to sponsor additional research directed at improving this new technology that would later be trade named, The E-Iron Process. Carbontec Energy conducted further work that proved that the E-Iron technology could also convert steel mill waste into metallurgically acceptable iron nuggets. Carbontec also collaborated with the Lawrence Livermore National Laboratory and Purdue University Northwest to conduct a Department of Energy (DOE) sponsored program that would use their high performance computer capability to both verify and model the E-Iron Process. Purdue University Northwest reported that the E-Iron Process can produce pig iron nuggets with 85% less carbon emissions than a blast furnace. The E-Iron Process is similar to the ITmK3 process, developed by Kobe Steel, that also produces iron nuggets but uses coal as the reductant.

Feb 1, 2025

Numerous underground coal mine ventilation seals have been installed in the United States of America prior to 2006 and after implementation of the Mine Improvement and New Emergency Response (MINER) Act. Seal engineering, design, placement, and construction is regulated in industry, but post-construction monitoring of seals is limited to visual inspection of the outby face and seal perimeter, convergence measurement, and atmospheric monitoring. To monitor seal integrity and to provide safe working conditions, a form of non-destructive testing (NDT) is necessary to accurately reflect the health of the seal by detecting post-construction changes, deterioration, or defects within in-situ seals in underground coal mines. Previous research from the National Institute of Safety and Health (NIOSH) has indicated the potential for utilizing ground penetrating radar (GPR) for assessing in-situ mine seals. This paper provides an update to the assessment of proposed NDT methods for seal evaluation using commercially available GPR technologies and systems. Full-scale free-standing seals and large-scale seal specimens were analyzed with an array of GPR units from various manufactures using multiple frequencies.

Feb 23, 2014

By V. P. Keran

Design of the Bajo de la Alumbrera Project started in June 1995 and concentrate production commenced early in the Third Quarter of 1997. The project is situated in North-Western Argentina and is being developed by Minera Alumbrera Limited which is owned by MIM Holdings Limited of Australia (50%), North Limited of Australia (25%) and Rio Algom Limited of Canada (25%). This paper outlines the key features that were incorporated in the design from both process and plant layout perspectives. It explains the background of flowsheet and equipment selection for the plant. A feature of the flowsheet is that it incorporates gravity gold circuits in both primary and regrind circuits for recovery of gold to dore as well as in the copper concentrate product.

Jan 1, 1998

By Madan M. Singh

It is estimated that through 1975, there were 1.69x109 m2 (418 000 acres) of urban land threatened by potential subsidence due to mining with a value of over $12 billion (19;3 dollars; USBM, 1979). With increased coal production to meet the energy needs of the nation, both these figures may be expected to increase. Hence greater attention to controlling surface damage due to subsidence is merited. In fact, the Surface `lining Control and Reclamation Act of 1977 (SMCRA) (Public Law 95-87) mandates that underground coal mining operators "adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonably foreseeable use of such surface lands, ..." The term "subsidence," as used in this paper, implies the total phenomenon of surface effects associated with the mining of minerals, and not only vertical displacement of the surface as is sometimes inferred in the literature.

Jan 1, 1984

By J. van Wijk

"Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems (VTS). To investigate flow effects under realistic conditions, especially clogging effects, a 136 m high test facility for flow analysis in vertical transport has been constructed using available mining infrastructure. Tests are run in a closed circuit, using a system of downfall and riser pipelines connected to a compact sediment injection- and separation unit as well as the centrifugal pump. The riser is equipped with pressure sensors, as well as temperature sensors, flow meter, concentration meter and high speed camera to allow comprehensive analyses of the flow regime and behavior of transported material within the flow. Additional mobile measurement devices allow wear and tear analyses of pipe material. This paper focuses on the determining factors of the tests leading to the design as well as the installation and trial of the test facility itself and explains the used components and work principles. INTRODUCTION Since the 1970s several research projects had been conducted investigating in the possibility of deep sea mining. In recent times projects for deep sea mining operations have started again, considering the rising demand on natural resources, especially raw earth elements. Yet projects like the Nautilus project on the deposit Solwara 1 [1], or Japanese projects focusing on the region of Okinawa [2] and Chinese projects [3] planning on depths of “only” about 2,500 up to 3,000 m. Until now no economical deep sea mining project was realized, due to the enormous difficulties of deep sea environments. Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects, considering transportation heights up to 5 km. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems or VTS [4]. Critical parts of the system would be identified and investigated to deliver solutions and higher the technology readiness level to a level were planning of a pilot project can be considered. At first case examples for mining projects of seafloor massive sulfides (SMS, 1,600 m water depth) and manganese nodules (MnN, 5,000 m water depth) had been calculated on basis of economical frame conditions, such as planned production rates to be efficient. As depicted in Figure 1 two major possible systems had been used for comparison, airlift system and pump system, considering multiple pump stations or single pumps. Based on the results and comparisons for the calculated vertical transport systems critical components and flow effects had been identified."

Jan 1, 2018

By A. L. Holmes

This presentation in the open pit session deals with the development of a phosphate rock strip mine by CF Industries, Inc., a company that does not presently mine in the Central Florida Phosphate District. Land acquisition, engineering, financing and environmental permitting activities were begun in early 1975; site preparation, environmental monitoring and dragline construction began in mid-1975. The operation is due on-stream in late 1978. The reserve acquisition, permitting, and financing could each easily be developed into a separate paper of interest. Each, however, has been covered before for other mining ventures with similar capital and environment requirements. For that reason, I have chosen to discuss what CF Industries, Inc. is, why it is entering this new sec-tor of the agricultural chemicals business, and, to keep at least some technical basis, what design modifications are possible when the total mine output is used captively and it is unnecessary to have the flexibility to meet the numerous transportation and customer specification considerations. In an attempt to show the size and complexity of the CF organization, a brief description of existing facilities should help show why the big interest in mining phosphate rock.

Jan 1, 1977

By Herry Poernomo, Agus Prasetya, Iga Trisnawati, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Panut Mulyono

We studied yttrium extraction from untreated zircon sand processing waste tailings. Xenotime mineral as the rare earth element source with an abundance of yttrium (REY) was detected in sufficient grade for extraction. As much as 9.03% yttrium exists in zircon tailings (analysed by X-ray fluorescence spectrometry). The presence of yttrium was confirmed by X-ray diffractometry in xenotime minerals, which are yttrium carriers (Y-PO4). The purpose of this research was to determine the effect of leaching conditions on yttrium recovery from zircon sand after alkaline fusion treatment. Alkaline fusion was chosen to decompose phosphate into hydroxide in the xenotimemineral,which will reduce further required hydrometallurgical processing.Alkaline fusionwas carried out for 3 h at 450 °C, with a ratio of sodium hydroxide to zircon tailings sand of ~ 1:1. The alkaline fusion product was leached with water, followed by hydrochloric acid treatment to leach the yttrium. Yttrium recovery reached 87% under optimum conditions (60 °C, 1MHCl, and solid-to-liquid ratio = 1/10 for 7.5 min). A suitable model for yttrium dissolution with hydrochloric acid was diffusion through a solid particle ash layer. The calculated activation energy (EA) for this model was 20.21 kJ/mol.

May 26, 2020

By J. M. Bray, R. R. H. Cohen, P. Kiousis, S. R. Al-Abed

"INTRODUCTION Conventional tailing storage and management practices typically utilize engineered facilities, such as ring dikes and valley impoundments. To reduce the environmental costs associated with disposing of mine wastes in tailing storage facilities (TSFs), several beneficial re-use strategies have been developed over the years. For example, thickened tailings have been used for paste backfill. It is common for tails to comprise up to 60% of the material’s total weight and it has been estimated that TSF volumes can be reduced by 60% when using this strategy, (Benzaazoua, et al. 2004). Other beneficial re-use strategies have produced unpaved temporary access roads, hot and cold asphalt, chip seals, self-compacting concrete, and golf course sand traps. This project sampled mine tailings from two different TSFs in Colorado and produced structural concrete that could potentially be used for commercial foundations, sidewalks, and paved roads. The tailings were substituted for the fine aggregates typically found in conventional concrete. The two main objectives of this study were to investigate the structural integrity of the produced concrete samples and the leaching of heavy metals from the resulting concrete. The ratio of tailings to fine aggregate (T/FA) was carefully studied to find if there was a correlation between the substitution rate and the structural integrity. The potential maximum substitution rate was also investigated for the produced concrete specimens. The potential of leaching mining impacted water (MIW) was evaluated by comparing the leachability of the raw mine tailings to the encapsulated tailings by using standard shake extraction prediction tests. MATERIAL AND METHODS Materials The four components that make up the concrete mix design for this project are: cement, coarse aggregate (gravel), fine aggregate (sand and mine tailings), and water. The type I/II ordinary Portland cement (OPC), gravel, and sand came from local cement and concrete companies in Denver, Colorado. Mine tailings were collected from two different TSFs in the Rocky Mountain Region, where Pride of the West TSF in Silverton, CO will be denoted as Site A. The primary metals of interest at the mill site are gold, silver, lead, copper, and zinc. The location of Site B will not be mentioned in this report due to confidentiality agreements with the mining company"

Jan 1, 2016

By D. Lauriski

The recent spate of catastrophic events at U.S. mines raises the question as to whether or not the mine safety and health system in the U.S. is broken. The prescriptive regulatory regime in the U.S. is not a cure-all for a broken system. Without totally dismissing the contribution of a prescriptive regulatory approach, this paper argues that safety in the U.S. mining industry would be enhanced if the nation adopted a scheme that provides a balance between specification standards and two alternatives: performance and systems-based standards. This would allow effective and flexible means to continuous health and safety performance improvement. Mine operators, regulators and politicians could then go beyond thinking that compliance alone equals strong safety by creating a proactive system that emphasizes continuous improvement. By adopting performance and systems-based standards, exemplary safety and health performers can be recognized, allowing regulators to focus their efforts on those without sound occupational safety systems and who have substandard safety performance. Mining Engineering, 2011, Vol. 63, No. 7, pp. 77-82. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Richard L. Ash

In many instances, blasting exerts the dominant control over the economics and safety of excavation, where the materials involved are too hard and tough to be fragmented efficiently by other means. However, associated with the fragmentation process other effects very often result that are not desirable and may even be hazardous, such as fly rock, air blast, excessive overbreak, and damaging ground virbrations. It has always been the desire of those concerned with blasting to better control the forces involved so as to improve the breakage of materials, but at the same time reduce, or eliminate if possible, the unwanted side effects. Until the last decade or two, little was known of the phenomena concerned with blasting. However, since that time many investigators have studied blast mechanisms produced from both chemical and nuclear explosions, with the result that general concepts of the principles have been developed. But, in general, it is assumed that the energy from the explosion would be propagated spherically throughout the material, the latter of which for convenience of analyses is considered homogeneous and isotropic, i.e., the properties are the same in all directions, However, rocks are not isotropic as a rule, and evidence clearly indicates blasting forces rarely function uniformly or in spherical form as theorized.

Jan 1, 1965