Search Documents

By Z. Y. Hu

This paper reviews the past and presents the present state of industrial minerals in China. The resources, reserve and production of major non-metallic minerals are given. The mining and milling operations are reviewed. The future development and plans of Chinese non-metallic minerals industry are summarized.

Jan 1, 1990

By D. Hodouin

Abstract. Dynamic experiments were performed in a continuous open-circuit 40x40 cm ball mill using a pseudo-random binary sequence of the feed rate and measuring the variations of the discharge particle-size distribution. The impulse response is calculated by a cross-correlation technique. Then a model involving a discrete transfer function and a time-series stochastic equation is calibrated using maximum likelihood methods. Based on this empirical model. a minimum variance controller with constrained input is designed and its performances are compared. by simulation, to the performances of a conventional PID regulator.

Jan 1, 1987

By B. T. Darnton

Gravity concentration at the Pegasus Gold Montana Tunnels Mine was initiated in late June, 1991 with the commissioning of a coarse gold scalping circuit that processes a small portion of the ball mill circulating load. The primary objective for the circuit was to reduce the risk of gold particles advancing to flotation that are too coarse to float. The secondary objective was to enhance overall gold recovery and payable gold ounces in a cost effective manner. The gravity circuit has proven itself to be a major success. The above mentioned goals have been achieved, and they have been maintained at record throughput rates that are 30% higher than when the circuit was commissioned. A number of modifications and improvements were made over the last three years which allowed the gravity circuit to keep pace with the higher tonnage, these are discussed in detail in the body of this paper. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project which will allow for an estimated 50% increase in gravity gold production, while reducing the overall unit costs of production significantly. This paper will review historical gravity circuit performance, improvements, and the current relocation and expansion project.

Jan 1, 1995

By W. B. Greer

The performance of seals in boreholes, shafts, and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines, and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in-situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall and others, 1982). This research involved the installation, extensive hydraulic testing, removal, and post-test examination of a l0-cm-long by 10-cm-diameter cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble peak in the Santa Catalina Mountains, Arizona. A test hole was diamond cored in the re-crystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diameter, and dips at 10.4 degrees. The hole extends between two drifts and thus is accessible from both ends.

Jan 1, 1992

By Peter F. Howard

The lower Middle Cambrian phosphorite deposits of the Georgina Basin shown in Figure 1 were found in the period 1966-1968 by three companies, namely, International Minerals and Chemical Corporation, Continental Oil Corporation and Broken Hill South Limited. Of these deposits the significant ones are Duchess, Sherrin Creek, D Tree, Lady Annie, Lady Jane, and Wonarah which together aggregate several billion tons reserves of phosphate. Due to the economic factors of freight costs to the coast and softening of the world market price for rock phosphate, none of them is in production, nor is any in the development stage. This paper reviews the historical background to the discovery of these deposits and then deals principally with the discovery of non-outcropping phosphorites in the Barkly Tablelands of Northern Territory by the interpretation of gamma radiation logs of abandoned water bores.

Jan 1, 1971

By Milos Krofta, Donald B. Aulenbach, James P. Van Dyke

INTRODUCTION An innovative Ø.1-MGD (378.5-m3/day) biological and phyicochemical wastewater treatment system at Hancock, Massachusetts, USA, has been treating the domestic sewage generated from the four-season Jiminy Peak timeshare resort since 1985. The influent raw sewage is collected and equalized in an equalization tank, then biologically treated by two rotating biological contactors (RBC). A portion of the RBC effluent is discharged to a secondary sedimentation tank to simulate conventional waste treatment by a conventional RBC system. For parallel treatment the remaining portion of the RBC effluent is discharged to an innovative Sandfloat (SASF-8) clarifier to simulate a two-stage biological and physicochemical treatment by RBC-Sandfloat. Both secondary sedimentation effluent and Saandfloat effluent are later combined together and discharged to a tertiary sand filter and two UV disinfection'units for final polishing. The operation and performance data of Jiminy Peak plant in the period of May 1985 to March 1988 was fully documented in the Lenox Institute technical report No. LIR/Ø3-88/292 (391 pages, March 1988). This report presents only background information and complete plant data in the period of April 1988 to January 1989. Dr. Lawrence K. Wang and Mr. James P. Van Dyke have been the Consulting Engineer and Director of Special Projects, respectively, for the Jiminy Peak Project since 1985. (Key Words) Innovative and Alternative Technology, Rotating Biological Contactor, Sandfloat, Dissolved Air Flotation, Sedimentation, Tertiary Filtration, Ultraviolet, Disinfection. BACKGROUND INFORMATION Jimmy Peak, Inc., Hancock, Massachusetts, has designed and constructed a secondary wastewater treatment system consisting of preliminary/primary treatment facilities, two rotating biological contactors, a dissolved air flotation clarifier, a secondary sedimentation clarifier, a sand filter and two ultraviolet (UV) disinfection units. Total average wastewater flow is approximately Ø.1 ) (378.5 cubic meters per day). In accordance with the Consulting Engineer's preliminary design, the total wastewater stream is initially collected and equalized by an equalization tank, and then biologically treated by rotating biological contactors (RBC). Part of the RBC effluent is diverted to a Krofta Sandfloat (SASF-8) for physicochemical clarification in order to simulate an innovative RBC-Sandfloat two-stage waste treatment system. The remaining part of the RBC effluent is diverted to a sedimentation tank for secondary clarification in order to siumulate a conventional secondary RBC-sedimentation waste treatment system for the purpose of parallel comparison. Both Sandfloat effluent and sedimentation effluent are later combined together and discharged to the subsequent sand filter and UV disinfection unit for final polishing. Figure 1 shows the flow diagram of Jiminy Peak Plant. The Massachusetts Clean Waters Act (M.G.L.c.2l,s.26-53) was amended by Chapter 246 of the Acts of 1973 to authorize the Massachusetts Department of Environmental Quality Engineering (DEQE), Division of water Pollution Control, Boston, Massachusetts, to regulate discharges into all waters of the Commonwealth of Massachusetts, including groundwaters. The DEQE regulates discharges through the issuance of discharge permits which impose limitations on the amount of pollutants which may be discharged in the effluent, together with monitoring and reporting requirements and other conditions to insure adequate treatment of all liquid wastes prior to discharge. The DEQE reviewed the application submitted on behalf of Jiminy Peak, Inc. for a permit to discharge sanitary wastes from the Jiminy Peak secondary wastewater treatment system located off Brodie Mountain Road, Hancock, Massachusetts, and subsequently developed the conditions contained in the Groundwater Discharge Permit No. Ø-188. More specifically, Jiminy Peak, Inc. (i.e. the permittee) has been authorized to discharge into the ground from the Jimmy Peak secondary wastewater treatment facilities for which the Permit No. Ø-188 was issued, a treated effluent

Jan 1, 1989

By Emily Wortman-Wunder

As the 2013 president of the Society for Mining, Metallurgy and Exploration, Inc., I am pleased to present the 2013 issue of the Transactions of the Society for Mining, Metallurgy and Exploration, Vol. 334. The timely publication of professional papers that promote the advancement of scientific and technical knowledge is critical for enabling technology transfer. SME plays a key role in this process through its publications. Communication within the mining community is the key to a successful profession and society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2013 Transactions contains 73 papers covering most every aspect of the mining life cycle and encompassing the diverse sectors of our industry including coal, industrial minerals, metals, health and safety and computational methods. It includes all 18 papers published in 2013 in the Technical Papers Section of Mining Engineering magazine (Vol. 65) and all 33 papers published in 2013 in Minerals & Metallurgical Processing (Vol. 30). Additionally, this volume contains 22 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. Some of the many research highlights from 2013 include discussions of perennial issues, such as how to adequately prepare the next generation of mining engineering students for the workforce (Frimpong et al., pp. 44-52) and how to predict and prevent coal mine bursts and bumps (Pariseau, pp. 60-68), the highly anticipated February Rare Earths issue of Minerals & Metallurgical Processing, and papers analyzing electrical injuries in the U.S. Mining industry (Homce and Cawley, p. 367-375) the latest in assessing the safety and efficiency of operations. All 73 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2013 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2013

By H. Wen

"Taking the long flame coal, gas-fat coal and anthracite as samples, we tested the adsorption quantity to single component gas of N2, CO2 and CH4 under atmospheric pressure phase at different temperatures. Then we analyzed the adsorption characteristics and models of different metamorphic coals. The results show that metamorphic grade, temperature and gases species are main factors to adsorption quantity of coal. The higher and lower metamorphic grade of coal have greatly influence on adsorption capacity while moderate grade of coal has opposite result. The coal adsorption amount to three single component gases under the same experimental condition is CO2> CH4> N2.The simulation precision order of four adsorption models is quadratic curve model > Freundlich isotherm model> Langmuir model >logarithmic curve model. Quadratic curve model and Freundlich isotherm model both can accurately describe the adsorption behaviors of N2 and CH4, different isothermal adsorption curve of CO2 needs two kinds or more models to describe. This has a reference value to the study of adsorption characteristics and models to single component gases.INTRODUCTION Adsorption is the interfacial phenomena that concentration of single or multiple components in the interface layer is different from the bulk phase (1964). Adsorption model is mathematical models to describe the adsorption characteristics of the adsorbent, mainly reflected to fitting effect of gas adsorption isotherm, which contribute to deeply understand the adsorption characteristics of adsorbent. Many scholars have carried out extensively experimental studies of the coal adsorption process from different angles. Zhao (2010) studied the influence of coal metamorphism to pore development of coal seam through a variety of experimental methods. Zhang (2006) analyzed the adsorption capacity and the controlling factors from three aspects of the coal rank, maceral and coal mass deformation. Cheng et al., (2002) studied the influence of pore size distribution of different rank coals to adsorption constants. Zhong (2002) carried out varieties of isothermal assay and established the prediction method of coal seam adsorption affected by a variety of conditions. R. M. Bustin (1998) proposed that we could not simply describe the change law of coal adsorption capacity and maceral content by a fixed parameter, and the adsorption capacity of the same coal rank also has great change. C. R. Clarkson et al., (1997) used four different adsorption models to describe the coal methane adsorption process, and the fitting precision of adsorption models is D-A equation >D-R equation > BET equation> Langmuir equation. Gasem, K et al., (2003) found that the fitted isothermal adsorption curve of D-A equation and BET equation are better than Langmuir equation under high pressure condition, while D-R equation and BET model are better to CO2 adsorption. In recent years, scholars’ at home and abroad research achievements of coal adsorption focused on high-pressure stage (about 0~15 MPa), mainly for coalbed methane exploitation, carbon dioxide trapping and sealing technology development, but the study of coal adsorption under atmospheric pressure phase is little. In this paper, we analyzed the adsorption characteristics and models under atmospheric pressure phase, it has a reference value to the study of characteristics and models to single component gas."

Jan 1, 2015

By Staff

In 2012, the estimated value of mineral production increased in the United States for the third consecutive year. Production and prices increased for most industrial mineral commodities mined in the United States. While production for most metals remained relatively unchanged, with the notable exception of gold, the prices for most metals declined. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Minerals? contribution to the GDP increased for the second consecutive year. Trends in other sectors of the domestic economy were similar to those in mineral production and consumption rates (Table 1). After continued decline following the 2008-2009 recession, the construction industry began to show signs of improvement late in 2011 and throughout 2012, with increased production and consumption of cement, construction sand and gravel, crushed stone and gypsum, mineral commodities that are used almost exclusively in construction.

May 1, 2013

By Kerby Glass, Glenn A. Gruber

Mr. C. A. Hollingsworth introduced commercial column flotation to the Florida Phosphate Industry in 1976, with a six feet diameter prototype cell at the Tenoroc Mine. More than two-dozen column cells have been installed in phosphate beneficiation plants since then. The increased interest in column cells for phosphate flotation, and their potential use in new plant construction, prompted the Florida Institute of Phosphate Research to fund programs to investigate various aspects of column flotation. This report describes a test program, conducted by JACOBS at CF Industries Hardee Complex II, as part of a comprehensive research program awarded to the University of Florida by the Florida Institute of Phosphate Research. The 1.5 feet diameter test column was operated with plant process water and plant reagentized flotation feed. Several variables considered for column cells design and operation were tested. Feed specific capacity, air superficial velocity, and the length to diameter ratio of the column were the variables that influenced phosphate recovery. Concentrate phosphate grade was influenced by concentrate superficial velocity and feed specific capacity.

Jan 1, 2002

By A. J. Getz

The paper reviews the status of the major precious metals projects in Australia, Papua New Guinea, Indonesia, the Philippines, and New Zealand. The projects may be at the stage of exploration, development, operation, or expansion. The paper covers project location, reserves, method of resource exploitation, anticipated production, and other unique conditions.

Jan 1, 1990

By Egon Pohl, Peter Eckl, Friedrich Steinhäusler, Johanna Pohl-Rüling

RADON EXPOSURE AND CARCINOGENIC CELL TRANSFORMATION The highest radiation burden to miners is due to inhalation of radon and its short-lived decay products. The quantification of the risk associated with this radiation burden is complicated by modeldependent lung dosimetry, insufficient accuracy of past human exposure data as well as lacking knowledge about potential synergism of various carcinogens. Nevertheless, it is evident from epidemiological studies of miners that inhalation of elevated levels of radon daughters is correlated with increased lung cancer incidence (UNSCEAR, 1977). The situation is further complicated by the lack of reliable data on the biological variability of the latency period for the development of lung tumor under varying exposure conditions. At present information on variation with age is scarce, however, it is indicated that the excess lung cancer rate for workers exposed to high radon levels is considerably higher, if exposure occurs at ages over 40 years as compared to under 30 years of age (Sevc, Kunz, Placek, 1976). Furthermore, latency period is shorter by 6 - 7 years for smokers exposed to elevated radon levels than for non-smokers (Fry, 1976). Analysis of US- and CSR-uranium miner data revealed that the mean latency period is in the order of about 15 years (Jacobi, 1973). These uncertainties, together with medical diagnostic shortcomings, lead to the dissatisfying situation that at present the detection of radon induced injury of mining personal is primarily the assessment of the endpoint, i.e. radiation induced cancerous transformation of lung cells with typically less than 10% chance for recovery. Therefore it would be advantageous to develop practically applicable diagnostic aids to indicate already early precancerogenic changes of cell characteristics. This would permit the identification of specific population groups at increased risk for the development of lung cancer, thereby increasing the chances of more successful medical treatment. Despite continuous improvements in the reliability of test methods for the diagnosis of cancer cells there is still need for techniques, which enable the detection of transformed cells before the onset of invasion of the host organism. It is generally recognized that the transformation of a cell into a malignant state leads to a change of the cell surface, indicating a correlation between membrane-specific immunological properties and loss of growth control. Surface alterations on cells appear to be responsible in part for the malignant state and are not simply secondary effects of the transformation (Schnebli and Burger, 1973). Furthermore, membranes of cancer cells differ significantly from those of normal cells, particularly, in permeability properties (Rastogi, 1976). In dying cells, proteins, glycoproteins, peptides, aminoacids and their breakdown products are released, which block the permeation of the membrane itself. A mammalian cell can be considered as a 3-phase system (interior, boundary, environment) with the membrane forming a heterogeneous barrier between two subsystems. Under normal circumstances a difference of chemical potential is maintained on both sides of the membrane, causing an ion gradient across and fixed surface charges on the membrane. This results in a membrane resting potential (MRP) between cytoplasm and the bulk medium. It has been shown that MRP is a highly sensitive indicator for cellular reactions due to physical, chemical and biological agents, particularly whenever phenomena of transport and ion gradients as well as permeability are involved (Redmann, 1980). The primary interaction of the agent "ionizing radiation" with any form of living matter occurs at the cellular level. The component with the highest hit probability is the cell membrane. In the study presented MRP-changes of human cells were investigated with simultaneous measurements during irradiation and post-irradiation intervals up to six days. Furthermore, the suitability of MRP-measurements of human cells was tested as an indicator for early changes of cellular properties prior to the histological confirmation of carcinogenic transformation. EXPERIMENTAL METHODS Lung cells The biological specimen used were cultured human lung cells and human lung biopsy samples. Monolayers of lung fibroblasts (W138) were grown in petridishes using conventional culture techniques. In addition, transformed lung cells (W138SV13, subline 2RA) were used applying similar culture methods. All petridishes were incubated at 37°C and only cells in logarithmic growth phase were used. Freshly excised lung biopsy samples were obtained from randomly selected male and female patients (20 cases), where suspected or unclear malignancies were indicated by clinical or X-ray observations. At the time of sampling 80 % of the patients were or had been smokers in the past. The samples were taken by means of a stiff bronchoscope introduced into the trachea under local anasthesia with 1 % Novesinsolution (preparation with Atropin and Pantopen). This permitted the observation of both main bronchi down to the segmental bronchials. From each patient two tissue samples were excised from the mucusepithelial layer under visual control with fiber optics and transferred immediately into 1 % NaClsolution. One sample was taken from the suspected

Jan 1, 1981

By R. J. Bridwell

Acid mine drainage (AMD) occurs in high sulfur coal and heavy metal mining environments. We show remediation methods using 3D numerical ground water flow models and chemical kinetics of pyrite oxidation for acid leaching of pyrite during air and ground water flow. A recently developed numerical model couples air and water flow with kinetics of iron-reactive bacteria, oxygen transport, specific chemical reaction rates, and pyrite oxidation to calculate migration control of pollution. A model is presented which considers diminution of acid mine drainage in pyrite rich ore bodies by raising the potentiometric surface through a vadose zone to reduce acid mine drainage. A ground water model is presented of an initially saturated mountain, containing an adit, with a sloping ground water table. Ground water recharge consists of snowfall and normal precipitation. Simulations indicate that the historically open adit creates a desaturated mountain above the adit. Significant air saturation ranging from 10-90% oxygen can occur to depths of the adit (-270 m). Remediation consists of plugging the adit, which fill s adit and mountain with water from recharge. Plugging the adit required <10 years for resaturation and rise of the water table in the mountain.

Jan 1, 1994

By Thomas N. Walthier

This paper will review world trends that are increasingly restrictive of mineral exploration and mining throughout the Free World This is occurring in the face of projected huge increases in demand for mineral products Some of the impediments are direct and absolute; others are indirect, but nevertheless effective; still others represent merely hostile attitudes Many of the world governments have a reputation for lack of integrity in dealing with existing foreign investments within their borders, and consequently are quite uninviting places for new investments, especially in the capital intensive natural resources industry. Compared with even 35 odd years ago (and pre-World War II is not that long ago) there are few places left where private mining investments are both wanted and where investors are willing, to go. We shall begin with an analysis of conditions in the U. S., shift to neighboring Canada and Flexico, and then have a look around the world. As the world grows smaller for the private mining sector, the function of exploration, development, and operation is passing over to government. We&apos;ll conclude with a view of what this holds for the future

Jan 1, 1976

By Alireza Kamrani, Yashar Pourrahimian, Hooman Askari-Nasab

In-pit crushing and conveying (IPCC) is an option to decrease the enormous operating costs that a truck shovel can introduce in an open-pit mine. Finding the best locations for the IPCC over the mine life will impose a new set of requirements for the mine planning. Through a two-step mathematical programming model alongside the road network, this method finds the optimal in-pit crusher locations and relocation times first and then optimizes the long-term mine schedule. The model is verified by a real mine. The results show that the truck travel time could be reduced by 500% and the discounted cash flow increased by 8% with an optimized schedule considering the crusher placement.

Jun 25, 2023

By J. R. Tonry

In the grinding of dry non-metallic materials such as rocks, ores, gypsum, lime, and cement clinker, it is recognized that only a relatively small portion of the energy is utilized for actual size reduction, and the major portion of the energy used is converted into heat. As a result, heat is generated inside grinding mills imparting to the ground product a higher temperature than that of the mill feed. In some cases, as for instance in grinding cement clinker and gypsum into finished cement, it may be desirable to keep this temperature increase within certain limits, to avoid any change in the properties of the product and, because consumers may specify a maximum temperature of the finished product for reasons associated, with the tulimate use of the cement. The actual proportions of heat and useful work are somewhat indefinite. Some tests have indicated that nearly all the energy is converted into heat, and. other investigators have found that they could account for "everything except the noise." Investigations sponsored by the American Institute of Mining and Metallurgical Engineers, and carried out with an adiabatic calorimeter, indicated that a surprisingly high 19 percent of the energy might actually be used for size reduc¬tion. However, for the purpose of the following discussion it will be assumed that: (Fig. 1) 10% is lost in motor and gears 10% is lost by radiation and convection from the mill body 10% is used for size reduction, and. that 70% of the energy input leaves the mill as heat in the ground. product. A typical example (Fig. 2) would be a 7x22-ft tube mill operating in open circuit, driven by a 400 hp motor, charged with 77,000 lb of grinding media and producing 70 bbl or 26,300 lb of cement per hour. Reducing this cement from a clinker size of 96 percent passing a No. 16 mesh sieve to a specific surface of 3,230 sq cm per gm (Blaine) will increase the temperature of the cement approximately 143F above the temperature of the feed, as explained later. If the tempera¬ture of the clinker therefore is 125F, the finished cement will be 268F, which in some cases may be too hot. : When cement temperatures approach a range during grinding where dehydration of the gypsum becomes a problem, a logical consideration would be some means of reducing the temperature before it attains the range conducive to gypsum dehydration. Regardless of the varying degrees of heat generated within the mill or mills during grindingto various finenesses, consideration of the maximum safe limit for any type of cement being ground, which may vary fromplant to plant, govern in refining the mill circuit to obtain a safe temperature range. All plants are not necessarily required to do the same cooling job, and may or may not use cement coolers following the grinding circuit. (Not discussed in this paper). In the past, various means have been employed for controlling this temperature increase, Such means have included water cooling of the outside of the mill shell; equipping the shell with cooling fins; injection of moisture inside the mill; ventilation through the mill; and., in cases of closed-circuit grinding, drawing cooling air through the classifier; the purpose in all such cases being to remove heat from the grinding system.

Jan 1, 1958

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

Technical Papers, Mining Engineering Vol. 49, No. 12, pp. 70-75, Discussion by McIvor, R. and Fink, R. P. We must challenge what we consider to be dubious statements in the above-mentioned article. Much of what is reported was published elsewhere over a year ago (i.e., in their reference: Chi, G., Fuerstenau, M.C., Brandt, R.C. and Ghosh, A., 1996, "Improved comminution efficiency through controlled blasting during mining," International Journal of Min¬eral Processing, Vol. 47, p. 93). There is nothing unusual or significant about a 10% or more difference in grindability between two materials of apparently similar origin and other attributes (such as chemical assays, hardness and specific gravity). Consider also that: • the materials came from different locations in the pit; • only two sets of four blastholes were considered per blast: • spatial orientation with respect to the face and other blastholes was also altered; • only two pairs of data were collected; • the impact of sampling error and bias, • both of which could be significant in this case; and • normal experimental error in parameter measurement and calculation. It is clearly inappropriate to draw any conclusions with regard to cause-and-effect relationships without first presenting a thorough error analysis. A substantial number of randomly selected test and control areas might provide meaningful statistical evidence of the claimed effect of the variables being studied. Even that appears doubtful, however, because Figures 3 and 4 show about as much variation in crushing energy for the two "regular" conditions vs. regular and altered conditions. On a separate, but also important issue, broad experience with autogenous/semiautogenous milling has shown that smaller or weaker feed material results in reduced tonnage. ? Reply Thank you for the opportunity to respond to the comments of Messrs. Mclvor ant Fink. The points raised are addressed in the order of presentation. As the commenters noted, there are parallels between this article and a previous manuscript. The reason for these complementary articles is that the audiences for the two publications are different, although there is obviously some overlap. We believe that the different audiences each profit from the technical aspects of the two manuscripts. We are not in agreement that a grindability difference of 10% is insignificant. The laboratory work is corroborated by data obtained at plant scale, which confirms that an increase in throughput of the same magnitude (between 5% and 10%) is achieved when the blasting pattern is modified, i.e., reduced from 9 to 8 m (29.5 to 26.2 ft). This increase in throughput translates into substantial power savings for ore grinding. No differences in appearance in the rock were noted between the two adjacent areas. Rock in both areas belonged to the same rock mass/block, which was quite homogeneous and without geological features in between that could create drastic differences in comminution characteristics. Given the resources, we would have sampled from all of the holes. Additional data would certainly have been desirable, as would have been additional funding to expand the study. Their comment, "spatial orientation with respect to the face and other blastholes was also altered," is not clear. Figure 1 does not show the initiation sequence. Without the initiation sequence, we do not understand how the commenters concluded that spatial orientation with respect to the face and other blastholes was altered. The commenters may be trying to make the point that the four-hole configurations with respect to the original bench face are not exactly the same. In fragmenting the

Jan 1, 1999

By R. K. Singhal

In 1990, Canada produced 69.4 million tonnes of coal of which some 65 million tonnes was produced by surface mining methods. The two Western Canadian provinces, Alberta and British Columbia produce approximately 55 million tonnes of coal by surface mining. These two provinces also provide the bulk of the metallurgical coal for export. The geological conditions in the Western provinces particularly in the mountain region are complex. The coals are friable and the seams are steeply inclined, sheared, intensely folded and faulted. There may be as many as 15 to 20 coal seams present with true thickness ranging from 2.5m to over 8m. Most of the Canadian surface mines are large (over one million tonnes per annum) using modern mining equipment such as shovels, high capacity trucks and draglines. At present the industry is going through another of its up and down cycles but has continued to make impressive gains in productivity. This has been achieved through greater mechanization, better management practices and a will to succeed in a highly competitive world market. This paper presents an insight into the current status of the Canadian Coal Industry and essentially updates the information given by the authors at previous SME meetings.

Jan 1, 1992

By Tina Živec, Žibertm Marko

"Civil design has changed in many ways using BIM (Building Information Modelling) technology in its most recent form. Such a technological breakthrough has not been successful so far in traditional oriented Engineering Geology, except in the Mining and oil exploration markets with budgets on much different scales. The fact is that paper, pencil and hand drawn sketches are still state of the art and a perfectly acceptable way of producing subjective geological interpretations.Using the technology available, we have developed a set of procedures and techniques to combine the latest surveying and remote sensing technology, GIS based tools to manage large data sets and BIM modelling techniques in a 3D geological environment.To demonstrate the concept, the forthcoming Karavanke tunnel project (Slovenia) has been chosen for testing techniques. The project, with its rich documentation from previous phases and new data available, represented a good basis for testing the possibility of digitizing geological data while communicating with Leapfrog Geo 3D modelling algorithms. This type of procedure would then allow engineers at the construction site to use the 3D model for prognosis and evaluation, while upgrading it daily with new information.INTRODUCTIONThe Karavanke tunnel crosses the mountain range on the border between Slovenia and Austria. As the geology is very complex due to its imbricate fan structure, a series of geological – geotechnical and hydrogeological investigations have been performed since the 1970s, resulting in extensive project documentation. The construction of the 7864 m long single-tube two-lane tunnel took place in the late 1980s. Currently, the tunnel represents a critical point on Pan-European Transport Corridor X (Salzburg, Austria – Thessaloniki, Greece), with insufficient safety measures. The need for improved traffic flow and enhanced road safety led the Slovenian government in 2013 to a decision to continue with activities regarding the construction of the second tunnel tube 70 m east of the existing tunnel.The extensive project documentation from previous investigation phases and construction of a new tunnel tube presented a good base for a pilot project, in order to test the emerging new technologies for data acquisition, processing and analysis in a 3D environment. Several products are available on the market for data acquisition and 3D geological modelling, but only a few can be applied in the civil design, as well. Developing a standard format and procedure for implementing the 3D geological model using new remote sensing techniques, 3D geological modelling tools, such as Leapfrog Geo and BIM (Building Information Modelling) modelling techniques would move the Engineering Geology, Geotechnics and Tunneling to a more advanced level. 3D modelling tools would therefore not only be used as a visualization tool, but would also contribute to in a more efficient communication and workflow between the professionals involved in the project."

Jan 1, 2016

By James M. Griffin

It was not many years ago that people would have argued that a coal session did not belong at an International Mining Convention. Historically, steam coal has always been used domestically due to its natural geographic diversity and high transportation expense. Times have changed. With the help of Opec, steam coal has gone international. As opposed to metallurgical coal, whose trade routes have a long history, whose supply sources are more limited and whose market growth is seen by most to be relatively flat, steam coal export forecasts are calling for more than a doubling by 1990 and a quadrupling by the year 2000. Suddenly, one must be familiar with coal mining on a global basis in order to predict which regions will be able to fill these markets.

Jan 1, 1982