Search Documents

By Huiqin Yao, Dongmei Liu

The study investigated the potential use of low activity circulating fluidized bed combustion (CFBC) ash and phosphate tailings for the production of a filling material based on the cement. The phosphate tailings were used as aggregate and consolidated by cement and CFBC ash. The results showed that the bleeding rate and fluidity of all mixtures decreased with the increasing the amount of CFBC ash. The fluidity of filling slurry is highly related to the experimental factors such as the content of sulfur solid ash, B/A ratio, and mass concentration. The replacement of CFBC ash ranging from 20 to 40% led to a significant decrease in setting time and an obvious increase in compressive strength, but the above effect was obviously weakened when reducing the mass concentration and B/A ratio. The hydrated calcium silicate gel and ettringite generated from the hydration of cement and CFBC ash were the main sources of strength for the filling materials. When the recommended proportion was 1/6 binder/phosphorus tailings ratio, 76% solid content, and 40% CFBC ash replacement, the filling material still met demands on working and mechanical properties; at the same time, the utilization of CFBC ash and phosphorus tailings was maximized.

Oct 11, 2021

By P. Geoffrey Feiss

The Piedmont province of the southern Appalachians is becoming the focus of interest for many exploration geologists. In the past, only those deposits with significant surface exposure have been exploited. Thus, few deposits have been found and relatively little exploration has been conducted in recent years. Modern geochemical and geophysical techniques can alleviate this problem of concentrating on exposed ore bodies by allowing us to "look through" the soil and saprolite to detect the presence of significant mineralization at depth. This paper will attempt to evaluate the feasibility and effectiveness of several geo¬chemical exploration techniques in the Piedmont, of Cabarrus and Stanly Counties, North Carolina. The area chosen for the study is shown in Figure 1, lying almost wholly within the Mt. Pleasant quadrangle, North Carolina. The area is on the eastern boundary between the Charlotte belt, a zone of plutonic and intermediate grade metamorphic rocks, and the Carolina Slate belt, a series of complexly interbedded volcanic and sedimentary rocks of predominantly low grade metamorphism. The area is now considered to be a 500 million year old active, continental margin.1 As is typical of most of the piedmont, outcrop is sparse. Figure 2 is a sketch map of the general geology of the area under study, showing the Charlotte belt rocks in the northwestern quadrant and slate belt rocks, to the east. Within the area are a number of old mines and prospects, the most famous of which are the Furniss and the Phoenix mines in Cabarrus County. All are reported to have contained Au and Cu. Ag and Pb were reported from some. A summary of the deposits is given in Table 1. Data used in this study are from three Master's theses conducted at the University of North Carolina at Chapel Hill. 3,3,6 In separate studies, well waters5, B-zone soils3, and vein and float quartz6 from the area described were sampled and analyzed. Each study concluded separately that geochemical anomalies in the vicinity of the ores justify use of that specific sample type in a geo-chemical exploration program. However, no comparative study of the methods has

Jan 1, 1977

By D. McElhinney, K. Mohamed, T. Batchler, T. Matthews

Steel props are a type of standing support utilized in coal mines to support mine roof. In addition to the vertical roof loading, sometimes the steel props are subjected to lateral loading of spalled ribs. To enhance the safety of mine workers, the performance characteristics of the steel prop was studied under different scenarios of vertical and lateral loadings. Quik Stik props were used for use in this study. A uniaxial compression loading test was conducted for the Quik Stik prop assembly (inner and outer tubes, ball bearings, collar) to investigate the loading mechanism of the prop. Rupture tests were conducted for the inner and outer steel tubes of the Quik Stik props to estimate the yielding strength of the steel tubes. Nine Quik Stik props of 8-ft high were tested using the Mine Roof Simulator (MRS) at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh research facility. Three props were tested under vertical loading to measure the vertical loading capacity of the props. Six props were tested under lateral loadings with low and high roof-to-floor convergences to measure the lateral loading capacity and the retained vertical loading capacity of the props during lateral loading. Vertical loading tests showed that the tested props could be classified as yieldable supports with a stable load capacity of about 110 kips to 140 kips. Lateral loading tests showed that the vertical load capacities of the tested props were diminished because of applying lateral loads, and the props behaved as nonyielding supports with a maximum lateral load capacity of about 8.5 kips to 9.5 kips at stable lateral displacement up to 3 inches.

Feb 1, 2023

By R. J. Kolada

The ventilation systems of coal storage silos are normally capable of rapidly dispersing any accumulations of methane in the atmosphere above the coal pile surface. However, the results of an investigation which is presented in this report show that hazardous concentrations of methane can accumulate within the coal pile. Methane trapped within the coal pile is released into the atmosphere of the loading gallery when coal is discharged from a silo. If the methane released is of a flammable concentration it is necessary to ventilate the gallery to reduce the risk of an ignition. This report proposes a simple test, which, after further investigations may prove to be an effective method to calculate gallery ventilation requirements.

Jan 1, 1985

By M. Gorman

The Mineral Park Mine is an open pit copper-molybdenum mine located in northwestern Arizona, approximately 74 miles southeast of Las Vegas, Nevada. The property has been owned by the Duval Corporation, Cyprus Mining Company and Equatorial Mining of Australia. Mercator purchased Mineral Park from Equatorial in 2003. Mineral Park commissioned a 25,000 tpd copper and molybdenum concentrator in November and December of 2008. The process includes two stage milling (SAG and Two Ball Mills) fed by primary crushed ore. Metals are recovered in a copper-molybdenum flotation circuit consisting of mechanically agitated roughers and cleaners. The copper- molybdenum flotation concentrate is thickened and further processed in the molybdenum flotation circuit which separates the copper and molybdenum minerals into salable concentrates. The molybdenum circuit also uses mechanically agitated cells. This paper describes the plant and some of the highlights of the commissioning process.

Jan 1, 2010

By Joseph M. Driscoll

After 30 years of successfully mining gold, Newmont Gold has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East Underground at the rate of 864 t/d (950 stpd). Annual production is more than 3.1 t (100,000 02). More than 70 underground miners will be employed during Carlin East's estimated six-year mine life. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed, cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By Robert C. Bates

Published information discussing uranium mine radon daughter controls and related costs was examined and used to develop an estimated (projected) cost per ton for any level of control. Results show a clear power function increase of cost for conventional dilution ventilation as the annual exposure limit is lowered. Projections can be made using any assumed changes in consumer price index (CPI) and radon daughter working level months exposure limit. Bounds on the estimated costs are provided, and applicability of the final equation is discussed.

Jan 1, 1983

By Osvaldo A. Bascur

Standards and technology for bringing information to the desktop have greatly evolved in recent years. The benefits to be realized depend on how these new tools are embraced at the performer level. A key operating challenge is to ensure cooperative effort is geared towards the most efficient achievement of identified operating and corporate objectives. Presentation, application and database layers are emerging in successful client/server applications, the three-tier architecture.

Jan 1, 1996

By T. J. Lutz, D. S. Yantek, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

Federal regulations require the installation of refuge alternatives in underground coal mines. Of the inuse refuge alternatives, more than 95 percent are mobile refuge alternatives, with the remainder being built-in-place (BIP) refuge alternatives. Heat/humidity buildup has been one of the major concerns with mobile refuge alternatives. For BIP refuge alternatives, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP refuge alternatives, the U.S. National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP refuge alternative with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP refuge alternative. The results show that the air supplied to a BIP refuge alternative may require heating or cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 21 °C (70 °F) and a relative humidity of 90 percent, providing 13 °C (55 °F) dew point air at 775 scfm, which is slightly higher than the mandated flow rate of 12.5 scfm per person, kept the internal apparent temperature below the mandated 35 °C (95 °F). Results for each test case are presented.

Jan 1, 2018

By M. Kehnemuyi

The U.S. Department of Energy is charged, by federal law, with the responsibility for developing and implementing programs for long- term storage and terminal disposal of high- level radioactive wastes from both commercial and defense nuclear operations. Approximately 288,000 cubic meters of defense high-level wastes are currently in storage at the government's Hanford Reservation in the State of Washington, the Savannah River Plant in South Carolina, and the Idaho Chemical Processing Plant in Idaho (U.S. Department of Energy, 1980a). High-level wastes from commercial nuclear power production are stored in water pools or basins at various power plant sites. At the end of 1980, approximately 7.460 metric tons of uranium, contained within 28,300 fuel assemblies was in storage at various reactor basins. Although the present inventory of defense wastes are many times larger in volume and in total level of radioactivity than the commercial wastes, in the future, the latter will constitute a substantial quantity of wastes that will have to be disposed of. The present electric generating capactiy of nuclear power plants in the United States is 56.5 Gigawatts-electric (GWe). The amount of spent fuel that would be discharged and accumulated by the year 2000 from these operating reactors would be 38,000 metric tons. With a projected growth of the nuclear industry to 180 GWe in the year 2000, the amount of spent fuel accumulated at the turn of the century could reach 89,000 metric tons of uranium or approximately 318,000 assemblies. In any case, whether one postulates a no growth pattern or one where nuclear power provides its share in the country's electric generating capacity in the next two decades, a means for safe and environmentally accept- able disposal of high-level nuclear wastes must be found. Storage of commercial wastes in water basins, either at reactor (AR) sites or at away from reactor (AFR) sites, and storage of reprocessed defense wastes in surface or near surface tanks is a temporary solution and is not an alternative for permanent disposal.

Jan 1, 1981

By T. J. Loyd

The capabilities of the analog computer, the Mine Ventilation Simulator, installed at WHA's Safety and Health Technology Center in Denver, Colorado, are discussed. General opera- ting procedures are described showing how a mine model is produced, and how the model can subsequently be modified to produce a solution to a mine ventilation problem. A sample problem is included to illustrate the technique. The important role the Mine Ventilation Simulator plays in ventilation training is discussed, including experiences with the education of students at the Colorado School of Mines. This paper includes a summary of some of the advantages and disadvantages of the analog technique and suggests some design criteria for application to future development of analog computers, based on experience gained with the Mine Ventilation Simulator.

Jan 1, 1984

By Ernest M. Spokes

Maximum fan efficiency can only be obtained when the fan has the correct combination of size, speed, and blade setting to provide the required flow of air against the mine resistance. As the mine grows older, resistance decreases unless old workings flow is restricted, and new combinations of speed and blade setting or different fan sizes may provide greater economy.

Jan 1, 1977

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Laramide porphyry copper deposits are large, low grade (<0.8% Cu) deposits that contain disseminated copper minerals, breccias, and stockwork veinlets of copper and molybdenum sulfides associated with porphyritic intrusions in Southwestern New Mexico. Critical minerals, such as PGEs, tellurium, indium, germanium, and gallium are recovered from the anode slimes remaining after copper is refined. Detailed age dating, mineralogy, geochemistry, along with geologic mapping could refine the location of critical minerals within specific systems and could identify porphyry systems with elevated critical minerals that could become economic, in addition to the already produced copper, gold and molybdenum.

Feb 1, 2023

By Pratt Rogers, Aaron Young

This paper considers the mining industry’s need for digital transformation (DT) and presents a three-part review of the foundational components of the DT process: ubiquitous data, connectivity and decision-making. It also provides a discussion on the future of DT in mining as well as a research direction, which identifies the need of academia to provide support for mining companies in the form of both research and the education of digitally literate, dynamically capable mining engineers into the coming decades.

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) has been used by the mining industry for early fire detection in underground mines. The National Institute for Occupational Safety and Health (NIOSH) initiated a project to integrate real-time AMS sensor data with NIOSH’s mine fire simulation program, MFIRE 3.0, to simulate and predict the spread of smoke that would provide assistance to mine fire emergency response personnel. Determining the heat release rate of a fire using the monitored sensor data was a critical component of the successful completion of this project. NIOSH researchers developed a direct method to calculate the heat release rate when a fire is within close range of sensors. However, this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire heat release rate for complicated scenarios where a fire is distant from sensors and airflow splits and merges are present. The method was validated using a fullscale diesel fuel fire test conducted in the Safety Research Coal Mine at the Pittsburgh Mining Research Division and can help mine operators and safety personnel make informed decisions during a fire emergency.

Jul 31, 2020

By D. R. Tweeton

A modified push-pull field test and a computer model of cation exchange were developed to aid in evaluating cation exchange parameters prior to in situ mining. Reliable determination of these parameters is essential when modeling restoration of groundwater quality. The field test involves a much larger volume and much less disturbance to the ore sample than is feasible with laboratory measurements. This test can be performed in two or three weeks. It is relatively inexpensive, requiring one injection- production well and two or more wells for collecting samples of leach solution. The use of the model in interpreting test results is illustrated with field data from an in situ uranium mine. Much of the research was performed by the University of Texas at Austin, and was partially funded by the Bureau of Mines.

Jan 1, 1986

By P. B. Altringer

The Bureau of Mines, U.S. Department of the Interior, is investigating biodegradation of cyanide as a means of decommissioning heap leach operations. Biological oxidation decreased weak acid dissociable (WAD) cyanide in process solutions1from 50 to 170 ppm down to 0.1 ppm. The tests were conducted both in trickling column reactors, using quartz as the growth surface, and in upflow columns, using activated carbon as the growth surface. In addition, exploratory tests indicated that bacteria will destroy residual cyanide in leached ore. A flowsheet has been proposed for closure of heap leach operations in which the metals processing portion of the plant, possibly the carbon adsorption columns, or a collection pond is used as a bioreactor. The cyanide in the process solution is destroyed in the bioreactor and the treated water is used to rinse residual cyanide from the spent heaps. The water is recycled until the effluent WAD cyanide concentration meets discharge standards.

Jan 1, 1992

By Michael A. Werner

"A Yieldable Structure for Use in Areas of High Rock Stress & Deformation." Rock stress of up to 9000 psi have been recorded in the mines of the Coeur d&apos;Alene Mining district. Associated with these large stresses are rock fractures and deformation. In order to maintain openings required for mining, large wood preparation structures are constructed to provide access to the work areas for men and materials. These wood raise preparation structures are costly to construct and maintain. Therefore a steel-foam concrete structure was designed and proposed for testing which would be less costly to construct, require no maintainence and maintain its structural integrity while allowing up to 53 inches of wall rock deformation.

Jan 1, 1984

By J. C. Motz

During the past five years, Rexnord has developed, tested and introduced the Nordberg Omnicone Crusher to the industry. When the Symons brothers invented the cone crusher over 60 years ago, they employed the principle wherein the length of the crushing stroke was related to the free fall of material by gravity. This permitted the material being crushed to fall vertically in the crushing chamber; and in effect, caused the particles to be crushed in a series of steps or stages as the particles got smaller due to the crushing action. This also helps to reduce the rate of wear of the liners since the sliding motion of the particles is minimized.

Jan 1, 1986

By B. Denby

Recent advances in Virtual Reality (VR) technology have resulted in major opportunities to improve safety training of mine workers, supervisors and managers. The hazardous nature of both surface and underground environments limits the type of safety training that can be carried out. VR offers the potential to expose mine personnel to hazardous situations in a safe, highly visual and interactive manner. Customized simulations of mine layouts, dynamic operations and mine environment can be set up and mine personnel can be allowed to move around the virtual mine, making decisions at key points. The consequences of both correct and incorrect decisions can be immediately fed back to the trainee.

Jan 1, 1998