Search Documents

By Y. Pan, V. V. S. Vytla, P. Tukkaraja, R. BHARGAVA, S. Jayaraman Sridharan

Panel caving is an underground bulk mining method that utilizes gravitational force for mining massive, steeply dipping, and deep-seated ore deposits at a lower operating cost. To control dust and gas emissions entering the production level during the extraction of ore from the draw points in a panel cave, relatively negative pressure is created in the cave by installing an exhaust fan in the exhaust drift located on top of the cave. Since caving is a dynamic process, the design of an effective ventilation system is a challenging task, and therefore, estimation of airflow resistance offered by the broken rock inside the cave is critical. The complex and dynamic nature of caving also makes it difficult to predict the airflow resistance by using traditional approaches. This study investigates the effect of changes in the bulk porosity of the broken rock on the cave airflow resistance using computational fluid dynamics (CFD) approach. The results show an inverse relationship between the cave airflow resistance and the bulk cave porosity. The pressure-quantity characteristic curves presented in this paper provide valuable information for sizing and operating an exhaust fan used for a mature panel cave ventilation.

May 17, 2022

By Yoginder P. Chugh

Effects of moisture absorption on the behavior of the Dykersburg shale overlying Harrisburg coal seam in Southern Illinois are presented in this paper. Cylindrical samples of the shale 2.5 cm in diameter and 5.0 cm long were studied for weight gain and swelling strains at 90, 95, and 100 percent relative humidity and under immersed water conditions. After attaining equilibrium conditions, the samples were studied for changes in the strength and deformation behavior. The depth of moisture penetration was measured using the Vickers microhardness measurements. Using the basic mass transfer concepts, effective diffusion coefficients were computed for the shale.

Jan 1, 1980

By W. J. Douglas

The mine manager in today's environment is faced with a wide variety of problems and challenges which must be addressed if efficient and profitable operations are to be achieved. Expansion of operations has, in many instances, resulted in inexperienced work crews, face supervisors, and superintendents. The complexities of a mining system preclude rapid movement through the learning curve for moat personnel. The management of production suffers both from this inexperience and the lack of standard procedures and methods for planning, schedul ing and analyzing production systems. The lack of visibility of information, as well as of the operations themselves, due to their remoteness, adds to the problem of production management.

Jan 1, 1980

By Brian F. Taylor

The Mexican fluorspar industry is faced with and will face serious problems, some of their own making and others beyond their control. However, they still offer the most secure source of fluorspar for North American' consumers. Since 1975, even in light of declining markets, they have, increased then production capabilities' as shown in Table #1. In analyzing Table #1, we note that Compania Miners Rio Colorado has closed down due to their ore reserves being exhausted. Fluorita de Rio Verde expanded their acid grade fluorspar capacity in anticipation of additional North American business. Campania Miners Las Cuevas presumably increased capacity to meet their North American contractual commitments and to supply their own hydrofluoric acid plant (Fluorex) at Juarez, Mexico. Historically, the Mexican fluorspar industry has relied on the United States as the mainstay for their sales. As shown in Tables #2 and #3, the Mexican share of the United States market has moderately decreased. However, as noted in Table #4 the volume loss is substantial as explained below.

Jan 1, 1985

By Robert J. Ramsey, N. Finkelstein, Robert D. Jeppson

Introduction The Utah Copper Division of Kennecott Copper Corporation will present its contribution to the A. M. Gaudin Flotation Symposium in four parts. The first two segments will discuss briefly the historical development of the Utah Copper Division and describe the ore body. The third segment will review the facilities and operating procedures for the Utah Copper Division's newest plant, the Bonneville Concentrator. The fourth segment describes flotation process circuitry, including molybdenite recovery procedures, at the Arthur and Magna concentrators. (The Bonneville concentrator is a crushing and grinding unit and does not have its own flotation plant). 1. Historical Development Progress through change has been the key to the successful operation of the Utah Copper Division for more than 70 years. As the original low-grade copper operation, the pressures to remain competitive and profitable have dictated the timing and extent of each change. Much of the change has occurred through technological and economic advancements in the area of ore concentration. The Utah Copper Division of Kennecott Copper Corporation had its origin June 4, 1903, when the Utah Copper Company was organized. The initial mill of 300 tpd (tons per day) capacity was built at Copperton a few miles below the present Bingham Canyon mine site. From 1904 to 1910, the Copperton mill was expanded to a capacity of 1,000 tpd, and all of the known apparatus for gravity concentration were evaluated.

Jan 1, 1976

By Dave Southworth

After Abe Lee discovered gold (in April 1860) near the site of present-day Leadville, Colorado, he and is group staked nearly all of California Gulch with "speculative claims." They did so in an effort to grab any property that might be potentially profitable. But the plan did not work. New prospectors demanded a miners' meeting, from which arose the official "Bylaws of California Mining District, California Gulch, Arkansas River." These bylaws, adopted on May 12, 1860, established provisions as to the number, size and type of claims that could be filed. Fair laws invited more newcomers. By mid-summer, 5,000 people with tents and wagons were scattered from one end of the gulch to the other.Among the earliest arrivals to the region that spring were Horace Austin Warner Tabor and his wife, Augusta. H.A.W. Tabor, who was to become a pillar in the development of Leadville, arrived at California Gulch during a food shortage. He sacrificed his oxen so that hungry miners could eat. By doing so, he immediately became the friend of many. Augusta established a little store where she sold her baked goods and provided meals. Like most of the men, Horace prospected the surrounding hills. He only did so, however, for a short time. California Gulch yielded more than $5 million in gold during the next five years. By 1866, however, the placer gold was gone and most of the miners had packed up and left. Charles J. Mullen and Cooper Smith, who were grubstaked by a Philadelphian named J. Marshall Paul, found a new, rich lode at the Printer Boy Mine in 1868. It was the first underground gold mine in the Leadville area and marked the transition from surface mining to underground hard rock mining. Its discovery created a new but modest flurry of activity. Heavy black sand covered the region and made gold mining difficult. In 1875 William Stevens and Alvinus Wood decided to have the sand assayed. They discovered that it contained 15 ounces per ton of silver and was rich in carbonate. Stevens and Wood kept their find a secret for nearly two years. When the word spread in late 1877, the silver boom was on. In 1878 prospectors, merchants and others trickled into town from all directions. Dr. David H. Dougan closed his office. in Alma, crossed Mosquito Pass and set up shop in Leadville. Nobody seemed to need a doctor, however, and Dougan sat in his office for 28 days without a customer. On the 29th day he received word that there had been a mining accident and he was needed immediately. -That was the begin¬ning of his illustrious career in Leadville. Dougan was a successful physician, became mayor in 1881 and was later president of the Carbonate National Bank. Leadville was a simple community of log structures in 1878. By June of the following year, however, it had blossomed considerably. According to Cass Carpenter, as of May 1,1879, Leadville had "...19 hotels, 41 lodging houses, 82 drinking saloons, 38 restaurants, 13 wholesale liquor houses, 10 lumber yards, 7 smelting and reduction works, 2 sampling works for testing ores, 12 blacksmith shops, 6 livery stables, 6 jewelry stores, 3 undertakers and 21 gambling houses where all sorts of games are played as openly as the Sunday School sermon is conducted." Additionally, there were 36 brothels. When George E. King and other architects arrived, Leadville took on an air of elegance and sophistication. In sharp contrast to some of the Victorian-style, gingerbread-laced homes in Leadville, its suburbs were comprised of many tenement shacks and plain cabins mixed with a few commercial buildings, many mines and smelters. Mines sprinkled the area east of Leadville like pepper from a pepper shaker. Wherever there was a cluster of mines, a camp usually sprang up. Most were very close together. South of Leadville the giant Arkansas Valley lead smelter sprawled out between Stringtown and Bucktown in an area known as Smelter Valley. Founded in 1879 as the Billing and Eilers Smelter, the Arkansas Valley plant was operated by the American Smelting and Refining Company. Several other smelters operated in the vicin¬ity. In April 1878, Horace Tabor grubstaked prospectors August Rische and George Hook. For $64 worth of supplies and tools, he was guaranteed a one-third interest in their findings. Rische and Hook discovered the Little Pittsburg (often spelled Pittsburgh) Mine and made Tabor an instant millionaire. Tabor once purchased a "salted" mine, the Chrysolite; but instead of considering it a bad deal, he further developed the property and struck rich silver ore. Later, Tabor purchased the Matchless Mine for $117,000, possibly the only investment he made without partners. During its peak years, the Matchless yielded $1 million worth

Jan 1, 1998

By John Dodd

Advances in the technology of abrasion resistant irons and steels, which could help in combating abrasion and wear in mining operations, are reviewed. Nodular irons alloyed with nickel or copper and molybdenum, with acicular, bainitic or bainitic-martensicic microstructures are described. These alloy irons combine excellent castability and relatively easy machinabilitv with good resistance to wear. Recent progress in the development of high chromium molybdenum alloy irons is outlined, by which high temperature heat treatment of massive castings can be eliminated, alloy costs can be reduced and cracking problems avoided. Data is also given on the erosion-corrosion resistance of these irons. Trends in the development of improved cast steels are outlined. Factors influencing the toughness and abrasion resistance of manganese steels are considered. The 6% Mn 1% Mo manganese steels are shown to have a useful combination of toughness and abrasion resistance. Composite castings are seen as a means of com- bating abrasion in applications involving severe impact. A brief appraisal is given of recently developed martensitic wrought steels with improved weldability.

Jan 1, 1981

Room-and-pillar mining at White Pine started in 1953 from a sub-outcropping orebody that gently dips to 1000 m depths in a distance of about 6 km. High horizontal stresses were recognized in the mid-1960s which had obvious stability impacts when viewed in combination with the increased overburden stresses. Modifications in conventional room-and-pillar design were introduced through the years on a trial-and-error basis to help overcome stability and resource recovery problems. These modifications were based on pressure arch concepts using pillar yielding and/or pillar recovery, and on mine layout orientation to minimize stress impacts. While some of these modifications were successfully applied in some areas, they failed in others. Through the years, visual observations played a major role in panel design with contributions from stress measurements and analyses. However, the down slide in the copper economy during the 1970s and early 1980s resulted in a loss of interest in the application of these concepts. This paper reviews ground control problems and presents the results of recent stress measurements and computer analyses. They shed light on the importance of using yield pillars and mine layout orientation to control stresses at depth.

Jan 1, 1993

By Immo H. Redeker, O. E. Pothier, E. W. Gieseke

Phosphate rock is the primary source of phosphorus, an element necessary to all forms of life--plant, animal, and human. While phosphorus finds many uses in everyday life, it is an irreplaceable ingredient in all complete plant foods. With the present need for intensive farming, the fertility of the soil can be maintained only by external additions supplied by mines or other sources. A major consideration in any mining operation is to establish the economic and ecological impact of the development on the local population as well as the national interest. The Commodity Data Summaries, as published by the U.S. Bureau of Mines (USBM), is a ready reference concerning the importance of phosphate to the national and local interest. The summary of domestic and world pro¬duction is given in Table 1. During 19722 the demand for marketable phosphate rock exceeded the supply in the United States and the rest of the world. Domestic and world reserves are more than adequate to meet furture demands. Phosphate rock prices firmed and export prices increased, reflecting the change from oversupply to a shortage of phosphatic fertilizers. Demand is expected to exceed supply through 1973. New fertilizer plant capacity planned for 1973-74 will increase the production of phosphate rock by more than 5 million tons in the United States. Morocco and Spanish Sahara are scheduled to increase their production to 18 and 3 million tpy, respectively, within 2 to 3 years. The domestic phosphate rock production for 1972 was 40.8 million tons and 1973 was 42.1 million tons.' Industry, with government-supported programs, will emphasize restoration of mined land and solution of the colloidal slime disposal problem in Florida. The foregoing information comes by courtesy of The Division of Nonmetallic Minerals of the U.S. Bureau of Mines, January 1973. The summary gives a great deal of information but does not give a complete picture. There are many supporting industries which contrib¬ute to the area in which the mines are located. The figures shown in Table 1 deal with concentrates. To produce such concentrates many more tons of waste overburden and ore must be moved. Because of the competitive nature of the phosphate rock industry, data on concentration ratios not only are difficult to obtain but also are not for publication by companies. The concentration ratios vary from one mine to the next in Florida as well as in Tennessee and the western United States. To produce 42.4 million tons of phos¬phate rock in the United States required moving about 350 to 400 million tons of material. Domestic Industry. In 1972 some 26 firms and the Tennessee Valley Authority produced phosphate rock, with several firms produc¬ing from more than one mine. The distribution of marketable phos¬phate rock production was: Florida and North Carolina 82%; Idaho, Montana, Utah, and Wyoming 13%; and Missouri and Tennessee 5%. The value of this production was $223 million. The principal consuming classifications were: agriculture 75%, soaps and detergents 5%, plating and polishing 3%, animal feed supplements 4%, and miscellaneous applications 13%. Over 5,000 firms processed end-prod¬ucts for agricultural purposes. Uses of Phosphate Rock. The tendency in the United States has been to produce more phosphoric acid by the wet process, while the production of electric furnace phosphorus, triple superphosphate, and ordinary superphosphate has been on the decline. Exports of phosphate rock have been on the increase for several years and in 1971 reached 33% of total production. However, export sales of phos¬phate rock are expected to decline in the years ahead, both in total tons of sales and in percentage of production as domestic sales increase (see Table 2). The description and chemistry involved in the production of phos¬phate fertilizers is too complicated to be presented here. The Waggaman13 book is a very thorough reference on the subject involv¬ing production, utilization, and chemistry. The various operations generally have chemical plants near the dry plants or ship to associated chemical plants for further processing. Wet rock, dry rock, and ground dry rock of various grades are sold. In addition various grades of calcined phosphate rock, including defluorinated phosphate rock for animal food supplements, are pro¬duced. Various grades of phosphoric acid, superphosphate, triple suerphosphate, as well as diammonium phosphate, are produced. These products are available from the various producing compa¬nies listed in the text. For prices and specifications the producing companies should be contacted.

Jan 1, 1985

By J. Rao Mokka

Extensive exploration has resulted in delineation of a massive sulfide district on the north flank of the east-central Alaska range. The district covers approximately 400 square miles and contains numerous stratiform; transported and some replacement type sulfide deposits ranging in size from less than 1 million tons to 20 million tons. Five types of ores were sampled for the study. Mineralogical analysis revealed that the minerals are too fine grained for conventional grinding and beneficiation. Hydrometallurgical studies were con-ducted using ferric chloride as a lixiviant. Ore microscopic studies as well as electron microprobe analyses of minerals in the raw samples and leach residues explained the low recoveries for certain elements as well as sources of impurities that need to be eliminated from the process streams.

Jan 1, 1991

By Sah Rameshwar, T. Umadevi, K. S. SRIDHARA

In the magnetite iron ore pelletization process, oxidation of magnetite followed by sintering of the oxidized magnetite (hematite) is desirable. Optimum preheating time & temperature and roasting time & temperature is required to get the desired properties of the pellets with magnetite, hematite, and hematite–magnetite blend. In order to utilize the magnetite resources in a current induration furnace, which is designed for hematite resources, detailed pelletization studies have been carried out to optimize the firing cycle for magnetite concentrate as well as magnetite with hematite concentrate. Under optimum conditions, such as preheating temperature 1000–1150 °C, preheating time 10 min, roasting temperature 1250 °C and roasting time 7.5 min, the cold compression strength (CCS) of magnetite roasted pellets was 325 kg/p, and this was due to recrystallization of secondary hematite particles, and development of the strong slag bond between primary and secondary hematite particles. The strength of hematite concentrate pellets was 260 kg/p. From laboratory studies, it was found that without disturbing the induration furnace firing cycle, which is designed for hematite ore ~5%, magnetite concentrate can be used along with hematite concentrate in pellet blend and the strength of the pellets was 270 kg/p. As the magnetite concentrate increases in the blend beyond 5%, the preheating zone residence time should be increased or a supply of extra oxygen is required. Laboratory as well as plant investigation has shown that the addition of magnetite to the hematite mix blend improved the strength of the pellets compared to hematite pellet alone.

Oct 26, 2020

By Charles A. Beasley

Coal conversion to electricity or to substitute natural gas requires a significant quantity of natural and human resources including, in addition to the coal resource base, land, water and the construction and operating labor force. Each method of coal conversion has its advantages and disadvantages relative to conversion efficiency, preferred method of resultant energy transportation, resources consumed, and impact on the environment. Regulations which have been passed in recent years to maintain or restore the pre-project environment can add significantly to the capital and operating costs of both a conversion facility and its associated mine.

Jan 1, 1983

By Kenneth W. Luke

In the development of the ultimate pit limits for a narrow ore body, pa¬rameters necessary in the design of a functional, or working, pit become highly sensitive factors in the determination of ore reserve levels and their associated waste to ore stripping ratios. Through the use of geologic cross sections, ore reserves can be roughly calculated by utilizing a straight line approximation for pit wall slopes. The optimum position of the pit floor can be substantially altered from such a preliminary design though with the introduction of functional mining parameters, such as a ramping network, and working bench heights, berm widths, and bench to bench wall angles. Originally a computer program was developed to quickly evaluate changes in cross-section pit design with minimal alteration of input data. After developing a satisfactory technique of cross-section evaluation which incorporates working mine parameters, an optimization algorithm, or procedure, was developed and included in the program to eliminate much of the tedious manual decision-making required in determining the optimum location of the pit floor on each cross section. Optimization in this case implies the maximum profit pit. When pit and processing costs are defined or hypothesized, this computer program can be used to design the maximum profit pit, constrained by the recognized functional mining parameters. A second way of stating the optimization is that the program can be used to develop a pit design which minimizes waste stripping at any desired ore reserve level. The basic method of cross-section evaluation parallels present manual methods. Program input is a combination of data obtained directly from cross sections developed for, geological interpretation and pit design parameters selected by the mine planner. As a result it is easy for the mine planner to comprehend what the program is accomplishing, and thus participate in the development of the computer assisted design.

Jan 1, 1971

By J. R. Henke

Dewatering wells producing iron-rich water experience rapid declines in yield and drawdown due to the formation of ferric (Fe +) hydroxide deposits in well screen, pump intake and riser pipe. Precipitation is caused by a combination of dewatering-promoted iron oxidation and iron-oxidizing bacteria. Physical and chemical well rehabilitation techniques, as well as alternative well construction and well development techniques designed to minimize well clogging, were evaluated in this study. The addition of acid downhole feed systems to dewatering wells prone to iron encrustation can, in some cases, prolong their operational lives up to 500 percent that of unacidified wells.

Jan 1, 1989

By Wang Xuewen, Bao Qingbao, Xie Jiacheng, Yan Zewen

This study puts forward a virtual memory cutting method based on the prediction of AFC shape. The integrated key technologies include the generation of virtual teaching cutting curve, the height adjustment strategy of front and rear drum, cutting height adjustment strategy, the reciprocating cycle of cutting technology and so on. Through the two algorithms, SVM and ELM, the form of the next working cycle can be obtained by rolling prediction using the form information of AFC in the first several circulations. Based on the obtained dynamic fluctuation of the form in the vertical and horizontal working faces, the position and cutting information of the shearer during its operation can be controlled and predicted in advance, the memory cutting template can be adjusted and modified in time. Employing this method, the more stable, accurate and timely memory cutting of the shearer under the uneven coal seam could be realized.

Aug 16, 2021

By Charles S. Spirakis

The consistent occurrence of organic carbon early in the paragenesis of Mississippi Valley-type sulfide deposits suggests a genetic link between organic carbon and the sulfide ores. Reduction of sulfate in the mineralizing solution by organic carbon at the sites of mineralization is commonly proposed as the precipitation mechanism for these deposits, but inorganic sulfate reduction is too slow to be important to the chemistry of the ore zone, and bacteria, which catalyze sulfate reduction at low temperatures, are not known to survive at the temperatures of mineralization. Sulfate reduction with or without bacteria is not consistent with the sulfur Isotope evidence. Sulfur isotope studies also indicate that the derivation of sulfur from hydrocarbon at the sites of mineralization is unlikely. Organometallic complexing may be involved in the transport of metals, but no plausible mechanism for breaking these complexes at the sites of mineralization has been proposed. Reduction of partly oxidized sulfur species in the mineralizing solution by organic carbon at the sites of mineralization is a possibility which deserves further scrutiny.

Jan 1, 2013

By Russell Frith

The entire subject area of micro-seismic events due to stored strain energy, as distinct from gas-driven coal outbursts, can be readily sub-divided into firstly events with their energy source from within the coal seam (termed “bursts”) and secondly, event with their energy source outside of the coal seam in either the overburden and/or floor strata. The reason for sub-dividing micro-seismic events in this manner is that if the causation mechanisms and associated geotechnical conditions are materially different, then effective pre-mining predictions and subsequent operational controls may also differ. Attempting to explain a multitude of micro-seismic event types without consideration of varying source mechanisms will inevitably lead to inadequate causal explanations and effective controls.

By Ashish Ranjan Kumar, Steven Schafrik, Oscar Velasquez

Flooded-bed dust scrubbers installed on continuous miners use fibrous type multi-layered filters to capture dust from the airstream. Prolonged operations of the scrubber could lead to filter clogging due to dust accumulation. This results in reduced flow through the scrubber and elevated dust levels in the mine environment. This paper compares the performance of a conventional fibrous screen filter and a novel impingement type dust filter. The impingement filter is a self-cleaning system and was designed to have a resistance similar to the fibrous filter. The cleaning efficiencies for these filters were computed using iso-kinetic sampling and optical counting of coal dust particles in a clean unclogged state. The cleaning efficiency of the impingement filter also increased with an increase in particle size and was comparable with the conventional fibrous filter. The cleaning efficiency of the fibrous filter improved significantly with an increase in water flow. The non-clogging nature of the impingement filter and minimal maintenance requirement makes it an attractive alternative to the conventional fibrous type filter in mining applications. The research also proposes a term called ‘filter performance factor’ to compare the performance of different filters under similar operating conditions.

Sep 19, 2020

By D. F. Malott

The Michigan Department of State Highways makes extensive use of geophysics for subsurface surveying which would be applicable for uses in other fields. Examples of resistivity surveys are given which include a proposed large volume excavation with suggestions for land use after excavation, subsurface evaluation for engineering design, and a subsurface survey for land appraisal. An example of a combined refraction seismic and resistivity survey is shown where the resistivity is used for outlining the unconsolidated soils, while the seismic method Is used to outline bedrock and to evaluate it for rippability. A refraction seismic survey at the bottom of bridge caissons for evaluation of bedrock uniformity and a relative aid In assessing rock strength is reported.

Jan 1, 1968

By James E. Lawver

During the past century, the Florida Phosphate Industry has established an enviable record of innovative technology in nearly all aspects of mining and beneficiation. A notable exception is the lack of technology to improve the present practice of storing waste clay in earthen dams. The rule which has been adopted by the Department of Natural Resources states, "Since storage of clay wastes for long periods of time interferes with expeditious reclamation and since above grade storage of clays takes otherwise useful land out of production and raises potential health and safety problems, below grade storage and rapid reclamation techniques are encouraged." The two waste products from the beneficiation plant are clay slimes (-0.1 mm in size) and sand tailings. The sand tailings do not present a problem since the tailings rapidly dewater to a dry weight of about 100 pounds/ft3 and make good land fill. By contrast, disposal of waste clay slimes is a formidable task. The basic problem is simply that the waste clay not only dewaters very slowly, but also that the ultimate solids content is very low and in most cases the volume of the clay greatly exceeds the available volume of below ground storage of the mined land.

Jan 1, 1984