Search Documents

By Vern Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western porphyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized -1+1/2-inch (-2.5+1.3-cm) ores from the Kingston (0.9 pct CU) and Centennial (1.6 pct Cu) mines of Upper Michigan. Concentrates of 4.0 pct and 7.5 pct Cu, respectively, were obtained at recoveries of 85 and 80 pct of the copper in the feed. Eighty percent of the sorted ore was rejected as tailing. Sorting larger fragments improved the separation efficiency. Tests on -4+2-inch (-10+5-cm) sized Kingston (1.6 pct Cu) and Centennial (2.1 pct Cu) ore samples yielded concentrates of 4.3 and 4.5 pct Cu, respectively, with corresponding recoveries of 92 and 91 pct. About 60 pct of the sorted ore was discarded as tailing. Porphyry copper sulfide ores also responded to electronic sorting but at a lower separation efficiency. Sorting response was affected by the degree of segregation.

Jan 1, 1976

By L. Gutierrez, S. Gering, C. Calderon-Arteaga

"INTRODUCTION Drill and blast (DnB) represents the most important, and sometimes the most costly processes in a mine.. The cost of drilling and blasting operations greatly contributes to the “high cost trends of the overall mining operations” (Afum B. O. and Temeng V. A. 2015). The use of available information to improve the DnB processes can be the difference between a highly expensive process and an optimized one. Mining operations have access to several types of data sets and key information from a wide variety of different systems. This information is normally used to improve, evaluate and apply processes for drilling and blasting. This may include different types of data from the different stages of the process (before, during, and after the drilling and blasting operations), such as hole locations (planned and actual), penetration rates, drill operators, fragmentation (expected and resulting), explosive (design and usage), geology, vibration, and others. This information can be used on its own or combined for further analysis to reduce costs, improve safety, and evaluate results. Fortunately, due to advances in mining software, drill and blast engineers can exploit this data and create reports to evaluate results and improve the DnB process. However, as users start combining information from multiple datasets and establishing standard operating procedures for reporting this data across multiple sites, it becomes valuable to create auditable, automated, and sustainable processes for handling the information. In many cases the task of aggregating and standardizing the data formats has already been completed and is available to consumers via the Enterprise Data Warehouse (EDW). A data warehouse team extracts data from the source systems and transforms it so that it is meaningful for decision support (Barbara H. Wixom, Hugh J. Watson, 2007). Our initial implementation plan for the DnB solution included using data stored at the sites; however we learned early on in the process that much of the work for aggregating and supplying the required data was already completed. The goal for this case study is two-fold: to show how information can be used to make decisions and improve processes, highlighting the value of using an EDW for managing Drill&Blast information; and to discuss how technical challenges encountered during the implementations were resolved. This paper is targeted at users that want to better manage their DnB data or try to set up standardized workflows for using this information. This case study will discuss the process of implementing a DnB workflow at multiple sites within Freeport McMoRan Inc (FMI) using both data at the sites and information available using the EDW. The paper will begin with an overview of the project. The discussion will then describe how DnB processes were used to set up daily workflows in order to provide information for evaluating process and making decisions. The final section will discuss some of the technical challenges and how they were solved, as well as possible next steps for further improving the workflow."

Jan 1, 2017

By Ralph Musick, Brian Briggs

The U1h Shaft Project is a design/build subcontract to construct one 6.1 meter(m) (20 feet [ft.]) finished diameter shaft to a depth of 321.6 meters (m) (1055 ft.) at the Nevada Test Site (NTS). Atkinson Construction was subcontracted by Bechtel Nevada(BN) to construct the U1h Shaft for the Department of Energy (DOE). The project consists of furnishing and installing the sinking plant, construction of the 321.6 m(1055 ft.) of concrete lined shaft, development of a shaft station at a depth of 297.5 m(976 ft.), and construction of a loading pocket at the station. The outfitting of the shaft and installation of a new hoist may be incorporated into the project at a later date. This paper will describe the design phase, the excavation and lining operation, shaft station construction and the contractual challenges encountered on this project.

Jan 1, 2001

By T. G. Rozgonyi

The basic goal of this investigation was to determine the degree of drying of high moisture lignite through the use of high temperature and pressure steam autoclaves. Specific items studied were: a) the effect of lignite particle size, b) steam temperature and pressure required, and c) the time of ahydration. Although removal of sodium, ash, sulfur and other ash-forming minerals was not the goal of this study, basic analysis of effluent water showed organic material and alkalai metal content. Removal of inherent moisture from run-of-mine lignite was tested by lock-feeding the lignite, which was previously sized by screening into 25 kg autoclaves. High pressure, up to 4.053 MPa (588 psi), saturated steam was then introduced into the pressure reactor. Reaction time, pressure, temperature, and depressurization rates were strictly controlled for each reactor test run. Results indicate that about 80% of lignite total moisture was removed, including some of the inherent moisture, yielding a non-oxidized, and thus stable, lignite product. As stated, a side benefit occurred as some reduction of non-combustible portions of the lignite also took place. The conclusion reached as a result of the tests is that the steam-drying process can be successfully applied to reducing moisture in lignite, and may be considered for additional studies on acceleration of the coalification process. On the basis of the data presented, the author believes that lignite can be economically upgraded in steam autoclaves by simultaneously reducing the moisture content by 80 percent and the sulfur content by at least 50 percent. Upgrading the lignite by this method will result in large energy and financial savings.

Jan 1, 1984

By R. J. Sweigard

One possible alternative for disposal of flue gas desulfurization (FGD) by-products is use as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation of stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix proportioning of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48 percent and the peak stress could be decreased about 58 percent. The study indicates that fairly weak FGD materials can eventually lead to stability of backfilled highwall adits.

Jan 1, 1996

By F. J. Susko

The U.S. Bureau of Mines is using Fourier-transform infrared (FT-IR) analysis to investigate the bonding mechanism which occurs during the dewatering of clay slurries. High molecular weight polymers are used as flocculating agents in these processes. This investigation presents the results of an FT-IR study of calcium-exchanged montmorillonite treated with polyacrylamide (PAM) and polyethylene oxide (PEO). Both thin film and attenuated total reflectance (ATR) spectroscopic techniques were employed to study this clay-polymer system~ Results suggest PAM is adsorbed to the clay via the nitrogen atom of the polymer. A water bridge is involved in the bonding between the clay and PE~. Evidence also suggests that PEO may be adsorbed directly onto the surface of the clay.

Jan 1, 1990

By J. A. Murray

Maintaining satisfactory air quality in electro-winning tankhouses has been problematic and costly, particularly as plant operating current densities have increased. Conventional approaches, including the use of beads, hollow spheres, surfactants and coalescer devices, have not proved completely effective, requiring that powerful ventilation systems be installed. As workplace and environmental regulations become more stringent, containment of the acid mist at its source is more attractive. An electrode cap system based on this approach has been developed and tested in two commercial copper electrowinning tankhouses. The design, development, installation and cost of the new electrode cap system are described.

Jan 1, 1996

By James P. Ludwig

While we are all aware of the need for reclamation of mine sites, few managers and engineers seem to be aware that good reclamation begins with the earliest plans for mining and processing of ores. Far too often the attitude that reclamation is an add-on to worry about at the end of the mining process dominates the thinking of mine engineers and management, A common result is that the reclamationist can be faced with mining and waste disposal designs that are nearly impossible to deal with effectively from an ecological perspective. Everyone of us has been victimized by the down time and maintainence cost that resulted from the purchase of an outwardly attractive, but poorly designed piece of equipment. When confronted by design defects in equipment, a distraught owner can always trade it in, call a consumer advocate, or follow up one of the "lemon laws" at either the federal or state level. A poorly designed mine for reclamation purposes usually cannot be treated either with ease or cost effectiveness. Good reclamation can be effectively prevented by the designs used when the mine was planned. The purpose of this paper is to share some of the experiences our firm has had with reclamation projects at mines in the Upper Midwest as these were influenced or controlled by mine design decisions. My aim is to sensitize mine planners and managers to planning processes they should consider, and hopefully use, early in the mining process to assure successful reclamation during and after mining. Many of the examples I will cite are from experience gained at the recently closed Jackson County Iron Company taconite operation at Black River Falls, Wisconsin. I am particularly grateful to Mr. Vern Metzger, mine manager at JCIC, for his unflagging support of good reclamation practices, employee training programs (which have included reclamation techniques), and his forebearance to put up with our group of ecologists. I realize that this was a time when there were significant internal and external pressures to cut all costs including reclamation efforts. The collaboration has been successful as you will soon see.

Jan 1, 1984

Coal-derived flue gases contain CO2/SO2 and these contaminants preferably have to be captured by cheap sorbents. This remediation approach is from the standpoint of addressing issues such as global warming, acid rain and development of Advanced Power Generation Systems and to realize the economic gain as well. Conventional and existing dry scrubbing technologies use regenerable sorbents which are pollutant specific and require expensive stabilizers in order to attain versatility. This paper discusses the use a novel class of sorbents prepared from the heavy metal contaminated Berkeley Pit water (Butte, Montana) by a proprietary process developed at The University of Nevada, Reno. These sorbents are activated mixed spinel ferrite (MxFe,_X04)' Preliminary experimental results show that the sorbents have good desulfurization and CO2 decomposition capacities. The decomposition effectiveness of these mixed spinel ferrites was studied at 300°C and compared against the synthetic magnetite obtained from ferrous sulfate solution in our laboratory. The results indicated that the mixed spinel ferrite had good affinity for the adsorption and decomposition. The CO2 decomposition data of both sorbents fitted the first order reaction kinetics. Even though the surface area of the magnetite was higher than that of mixed spinel ferrite, the CO2 decomposition rate of the mixed spinel ferrite was estimated to be 2.5 times higher than that of magnetite under identical conditions. The carbon analysis deposited on the sample indicated that the CO2 was 100% decomposed into carbon and other carbon! hydrogen compounds by the mixed spinel ferrite whereas the conversion was 43% by the magnetite. In terms of specific adsorption of carbon, ferrite was 3-5 times more efficient than magnetite.

Jan 1, 1996

By Michael L. Maniocha

Most magnesia (MgO), whether of natural or synthetic origin, is used in the dead-burned or periclase form as refractory linings for the production of steel. Continued research in refractory science, combined with good refractory maintenance and improvements in steel-making processes, have resulted in decreased use of magnesia. To make up for this loss of business, producers of synthetic magnesia have started to manufacture a variety of magnesium-based chemicals that are used in many industries. There are three primary methods of producing MgO. The first involves the calcination of naturally occurring minerals species. Most of the magnesia produced by this method uses the rhombohedra1 carbonate mineral magnesite, MgCO,. To a lesser extent, the mineral brucite, Mg(OH), is calcined to magnesia. Magnesia produced by the calcination of minerals is called natural magnesia. The second production method uses magnesium-rich brines, or sea water reacting with lime or calcined dolomite to produce magnesium hydroxide. The magnesium hydroxide is subsequently calcined to magnesia. Material produced in this way is called synthetic magnesia. The third major method of production uses saline lake brines to produce magnesium chloride. Magnesium chloride brine is sprayed into a reactor where it thermally decomposes into MgO and HCl. The magnesia is purified by slaking to magnesium hydroxide followed by calcination. Magnesia produced in this manner is also know as synthetic magnesia (Duncan and McKracken, 1994). The degree to which the magnesium minerals or the synthetically prepared magnesium hydroxide is calcined governs the physical properties of the resulting MgO. It is the physical properties that dictate the end use for the product. The terms used to describe magnesia vary along with the degree of calcination. Table 1 summarizes the terminology used when discussing the various forms of magnesium oxide.

Jan 1, 1997

By T. J. Fenner

Surface and underground mining operations are often hindered by unknown tunnels and stopes and the precise locations of adjacent workings. Mine safety and planning are adversely affected especially in previously undermined areas where historical records are incomplete or non-existent. The results of several Ground Penetrating Radar (GPR) studies for the detection of known mine tunnels in underground coal; salt, and gold mines are presented. A case study to locate unknown, abandoned mine workings at a surface gold mine successfully located all workings to a depth of 11 meters.

Jan 1, 1992

By James F. McConnell

Federal and State sulfur oxide emission and ambient air quality regulations have been implemented to fulfill the requirements of the Federal Clean Air Act Amendments of 1970. Primary and secondary air quality standards have been established at levels considered necessary to assure the protection of the health and welfare of the public. Standards of performance under this Act have been established to control the rate of sulfur oxide emissions from individual sources so as to protect and to improve the quality of the Nation's air. The new source standards of performance were made rigorous for large coal burning stationary sources. This has had a severe impact on the electric utilities that operate the coal fired steam electric plants which are the largest consumers of the Nation's coal production. States have taken different approaches in State Implementation Plans (SIPS) as approved by the Federal Environmental Protection Agency. Some states, such as Pennsylvania, have chosen to permit moderate SO2 emission rates from existing sources which are not in critical air basins. All are required to meet primary and secondary air quality standards and to limit sulfur oxide emissions from new large stationary sources to a minimum of 1.2 LBS of S02/MMBTU fired. This re- quires a fuel sulfur percentage of about 0.7 for a 12,000 BTU/lb coal. In an effort to develop strategies and technologies to conform to performance standards while continuing and hopefully expanding the utilization of the Nation's coal supply, the electric utilities, the Federal and State regulatory agencies, and other industries and government agencies are considering several alternatives. 1. Natural low sulfur coal 2. Flue gas desulfurization - (FGD) non-regenerative and regenerative 3. Coal gasification 4. Liquefaction and solvent refined coal 5. Fluidized bed combustion 6. Chemical coal cleaning 7. Physical coal cleaning Of these options, only the first and the last can be considered to be widely used in full commercial practice at this time. FGD has certainly demonstrated technical and operating feasibility and is close to being in full commercial practice but it remains to be seen if the large systems under construction are economically and environmentally optimum.

Jan 1, 1975

By William G. Pariseau

The purpose of this paper is to present a discussion of the various approaches that can be utilized in the study of mine subsidence phenomena. Attention is focused upon the rational selection and use of laboratory models. Broadly interpreted, mine subsidence is the deformation of the rock mass enclosing the mine. Depending upon a number of factors, the movement of the subsiding rock mass may be such as to disrupt gas and water lines or other buried utilities, to damage surface structures such as buildings and bridges, to dislocate streams, roads, and rail lines, to aggravate acid mine drainage and fire problems, and to generally mar the landscape. It is clearly a problem that no mine manager can safely ignore. It is also a problem that will grow with the general population increase. In the following, a summary review of past and present approaches to subsidence studies is given. The possibilities of duplicating subsidence phenomena in laboratory models are examined, and an analysis of a particular type of model is presented. Some preliminary results obtained from a model of the particular type analyzed are then discussed.

Jan 1, 1968

By Nord L. Gale

The discovery of important new ore deposits of lead, zinc, copper and silver in 1955 in Southeastern Missouri has resulted in the development of a thriving mineral industry known as the "New Lead Belt" or "Viburnum Trend", to distinguish it from the older lead producing areas to the East. This region has recently become the world's largest lead producing district with production in 1970 reaching 432,576 tons or 74.4% of the entire United States lead mine production. The area is heavily forested with rolling hills dotted with numerous clear running streams in the Clark National Forest of the Missouri Ozarks. The location is within 70 miles of St. Louis, Missouri and has a natural abundance of water resources which provide an important recreational area for fishing, hunting, camping and other outdoor activities. Until this recent development, the area was sparsely populated and industrialization was almost unknown. The infusion of $150 million in mining capital has brought about a dramatic change in the economic structure of the area and will almost surely be accompanied by changes in its environmental picture. In an effort to maintain this bountiful national resource and to evaluate the changes occurring in surface water quality and aquatic life forms present, an inter- disciplinary research program at the University of Missouri has been undertaken with the support of the National Science Foundation. Research has been carried out to determine background values, establish natural baselines, and to evaluate the extent and causes of changes in streams effected by mine water discharges and wastewater from ore milling operations. The unique topography of the "New Lead Belt" area allows the channelization of milling and smelter wastes to separate stream systems (Figure No. 1) thus allowing measurements of the pollutional effects on an individual basis.

Jan 1, 1973

By B. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin. The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill. The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and then two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator’s station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt and mesh sump. The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in turn lowers the miners’ roof exposure per cut. This design reduces the operator’s exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely. INTRODUCTION When mining underground it is necessary to support the roof quickly to prevent it from collapsing after an area has been mined. Since the 1950s, the primary method for supporting the roof has been the installation of roof bolts. Roof bolting is one of the most basic functions yet one of the dangerous jobs in the underground mining operation (1). The Mine Safety and Health Administration’s (MSHA) Health and Safety Accident Classification injury database showed an average of 660 roof bolter operator accidents per year over a 5-year period (1999-2003) (2). The numbers show that roof bolting is the most hazardous machine-related job in underground mining. It represents 39 percent of all machine-related accidents in underground coal mines. In 1993, the U.S. Bureau of Mines conducted a study that has shown the activity of drilling as the most hazardous job task performed by a roof bolter operator, accounting for 31 percent of all roof bolting injuries (3). Almost half (46%) of these drilling injuries were due to falling rocks or coal from the roof. All of these injuries occurred under supported roof. The majority of these injuries (about 99%) are not caused by a major roof collapse but from falls of smaller rock from the immediate roof. This type of roof failure has also been termed “skin fall.”"

Jan 1, 2017

By Frank A. Jerabek

Problems of mine backfilling and fill material deposited underground, the characteristics and relationship between the deposited fill material and overlying ground, and the practical applications and limitations of hydraulic backfilling as ground support are discussed. A great variety of materials ranging from coal washery refuse to concentrator tailings is used as hydraulic fill. Some materials will solidify and cement; others will resemble quicksand, Hydraulic fill as ground support is more efficient in inclined mine openings than in horizontal mine openings, where it cannot be placed tightly to the back. This and other deficiencies of hydraulic backfilling led to the development of pneumatic stowing. Research work in hydraulic backfilling at the Pennsylvania State University is also discussed. This research work includes the investigation of segregation in the discharged fill slurry, the quantity of solids escaping in the drain liquid, the relationship of escaping solids to slurry concentration and discharge rate, and the compressibility of fine fill material.

Jan 1, 1965

By A. Podlesny, E. N. Rubinstein, J. J. Sammarco, B. Demich

Roof bolting typically follows the extraction of a commodity to help keep the roof from collapsing. During 2004 to 2013, roof bolter operators had the highest number of machinery-related injuries, accounting for 64.7 percent, at underground coal mines. This paper analyzes U.S. roof bolter fatal and nonfatal lost-time injury data at underground work locations for all commodities from 2004 through 2013 and determines risk indices for six roof bolting tasks. For fatal and nonfatal incidences combined, the roof bolting tasks in order of the highest to lowest risk index were bolting, handling of materials, setting the temporary roof support (TRS), drilling, tramming, and traversing. For fatalities, the roof bolting tasks in order of the highest to lowest risk index were handling of materials, setting the TRS, bolting, drilling, traversing, and tramming. Age was found to be a significant factor. Severity of injury, indicated by days lost, was found to increase with increasing age as well as with increasing experience, largely due to the confounding of age and experience. The operation of the roof bolting machine used in underground mining should be a research priority given the high frequency and severity of incidents. The results also suggest that temporal factors may exist, so additional research is warranted to better understand these factors and potentially develop interventions. This research provides a datadriven foundation from which future research can be conducted for safety interventions to reduce the frequency and severity of incidences involving the roof bolter activities of bolting, handling of materials, and setting the TRS.

Jan 1, 2016

By Stephen Utter

One function of mining is to supply oil shale of the required grade and characteristics to surface retorts. The mining methods must he safe, efficient, and environmentally acceptable. Although the Bureau of Mines no longer conducts research on methods of mining fossil fuels, including oil shale, its many years of activity in that field resulted in a significant body of findings. This article summarizes some of these findings, with respect to oil shale mining. The large areal extent of Green River formation oil shales and the diversity of geologic, hydrologic, topographic, and other conditions, preclude the use of any one single mining and waste management technique. Instead, in most instances, methods and equipment will be chosen to meet site-specific conditions. Such methods include conventional surface mining (open-pit and strip), underground mining (room-and-pillar, sublevel stoping, caving) and in situ extraction (true in situ from surface drill holes and modified in situ from underground retorts containing rubblized oil shale). Combination or hybrid systems may prove suitable. Both surface and underground backfilling of spent shale waste may be practiced. Tremendous amounts of oil shale must be mined, processed, and the waste shale properly disposed of in order to meet projected industry production goals. For example, about 1.4 tons of oil shale averaging 117 L of shale oil per ton are required to produce one bbl of oil. A plant with a daily production of 8 dam' (50 000 bbl) of oil would thus require some 68 kt of raw shale daily. This is more than the average daily production from any underground mining operation.

Jan 1, 1981

By H. M. Breza

Utilization of Bucket Wheel Excavators and Overland Conveyor Systems to remove overburden provides increased productivity and flexibility to a surface mining operation. The utilization of such a system at the Texasgulf Inc. Aurora, North Carolina Mine has significantly improved the overall productivity of the mining operation. System flexibility is evidenced by adaptation to operation requirements such as mining area moves, movement of excavated overburden to designated sites, selective handling of overburden, spoil placement contouring, and providing an environmentally sound and safe operation. System productivity is evidenced by actual case studies relating to overall production, excavation rates, and cost effectiveness.

Jan 1, 1993

By Thomas E. Newman

This paper is a case study using new laser-terrain-mapping technology by EagleScan, Inc., for creating topographic maps. Holnam, Inc., has used this technology to create maps and volumetric calculations of several mines in the United States. The information is superior to conventional methods through accuracy, manpower, time, and cost. Holnam, Inc., was the first cement manufacturer to use the Digital Airborne Topographic Imaging System (DATIS?). The technology uses the DATIS? to produce high-resolution terrain maps and volumetric assessments of any area. DATIS? is a mapping instrument that integrates (1) a Light Detection and Ranging (LIDAR) instrument to measure terrain elevation using laser light, (2) a large-format digital camera, (3) a relative position Global Positioning System (GPS) to measure aircraft position, and (4) an Inertial Measurement Unit (IMU) to measure aircraft attitude. The DATIS? can measure up to 220,000 elevation samples per mil. The system continually collects data on the aircraft's position and measures the time for each laser pulse transmission to return from the ground, giving each sample a GPS reference. The system can operate at night, in overcast sky, and during high-wind conditions and can measure terrain below vegetation cover, unlike standard aerial photography used for traditional surveying and mapping. Surveyed ground-control panels are no longer necessary with this new technology, and only one ground GPS base station located within 60 mi from the aircraft position is required. A computer elevation-point data file is created with the x, y, z coordinates of each laser elevation sample. With this file, CAD engineering programs can create topographic maps that rival products using conventional aerial mapping techniques. Volumetric measurements of stockpiles and pits are also available due to the high density of points collected from an area. This new technology radically changes the turnaround time for map users, giving a product in the format used by today's cartographers. The time line from flight to maps is measured in days instead of weeks.

Jan 1, 1999