Search Documents

By R. K. Mehta

An electrochemical coal oxidation model involving heterogeneous kinetics is presented. This model was tested by collecting current transient data on three coals assaying different ash content under varying operating conditions such as particle size, temperature, and % solids. In all cases, the model fitted the data very satisfactorily. Three intrinsic rate constants, namely mass transfer coefficient of Fe(II) Ions diffusing from solution to the anode (kma), mass transfer coefficient of Fe(II) Ions diffusing from solution to the coal surface (kmc), and chemical rate constant for coal oxidation with respect to Fe(III) at coal surface (k), were calculated. It was interesting to note that in this system, the mass transfer at anode was as important as the chemical reaction at the coal surface. The validity of this model was further demonstrated through a comparison of the activation energy of coal oxidation: firstly, by utilizing calculated chemical rate constant and assuming Arrhenius' type of relationship: secondly, by utilizing conventional approach using limiting current values. The comparison revealed that agreement was quite close. This kinetic analysis is useful because such a model can be used in predicting the intrinsic rate constants so that the relative importance of mass transport can be rationally analyzed.

Jan 1, 1991

By CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU, Shunliang Liu

With the depletion of mineral resources and the growing demand for metal resources from industrial development, the recovery of metal resources from secondary resources has attracted increased attention. Among all secondary resources, spent catalyst is one of the most important as it contains valuable metals such as vanadium, nickel, molybdenum, cobalt, and aluminum. Compared with the extraction of metals from minerals, the recovery of valuable metals from spent catalysts has the advantages of a simple process, a short production cycle, lower investment cost, and less environmental impact.

Apr 1, 2023

By R. E. Hochscheid

Cyclones installed in three closed- circuit grinding systems were changed from conventional, vertical mounting to horizontal mounting with a favorable improvement in classification efficiency. In two of the installations, apex plugging problems were eliminated because horizontal mounting permit- ted the use of much larger apex orifices. Marked reduction in circulating load was accompanied by greatly reduced maintenance requirements for the cyclone and the cyclone feed pump in one of the installations.

Jan 1, 1988

By B. Samanta

This paper highlights the use of an innovative mine production scheduling scheme for grade-control planning tasks that take into consideration grade-model uncertainty. The scheduling exercise has been carried out with the help of a multiobjective genetic algorithm (MOGa) for the production scheduling operations. The underlying motive behind the use of MOGa has been the generation of a set of pareto optimal solutions to meet the goals of the target-grade specifications for the considered multiple grade attributes. Several new concepts related to MOGa formulation, in particular the mutation operation and the convergence criteria of this algorithm, are proposed in this paper. The modeling of grade uncertainty into the scheduling outputs has also been incorporated through a set of conditional simulated grade maps. The proposed scheme of production scheduling operations has been applied for the grade-control planning operations in an iron ore mine to meet the targeted grade specifications of iron, silica and alumina, and a risk analysis has been performed to this end.

Jan 1, 2013

By T. A. Oberhellmann

The Wobbler Feeder is a comparatively new materials handling and separating device. It is essentially a materials separating or scalping machine, particularly adaptable to separation of oversize particles from mine-run ore and to the separation of oversize materials from overburden, where the removal of oversize materials is necessary, as is the case in conveyor stripping. In construction, the Wobbler Feeder is simply a set of transverse bars of manganese steel, or other wear-resisting alloy steel, each having an elliptical cross-section with the major axes of adjacent bars displaced by ninety degrees so when rotating in unison, the pre-determined space between the bars remains constant.

Jan 1, 1959

By Allen D. Graham

The coal industry in South Africa is briefly outlined. Test- work carried out on bulk samples of coal in the laboratory and used in the design of the Van Dyks Drift washery are described. Factors affecting the selection of equipment and the designed capacity of the plant are discussed. A description of the crushing plant, washery and load out section is given together with performance data obtained in the final acceptance tests. New features incorporated in the Van Dyks Drift plant and in more recent plants of the Group are outlined.

Jan 1, 1982

By S. Simske, K. Boakye, D. Winters

The application of digitization to operations and logistics is commonplace. From advanced data analytics to intelligent networks, digitization offers tremendous opportunities to create value, raise the efficiency of production processes, and reduce emissions. Several manufacturing industries have already implemented solutions to good effect by using digitization. Mining companies, for example, are using historical data about equipment health to predict potential failures, while aeronautics and automotive companies are using robotics and end-to-end digital twins to improve their design and production processes. Not surprisingly, first adopters of digitization in many industries have gained an edge over their competition. The cement and aggregate industry can better manage the enormous energy consumption, rising cost challenges, inefficient uses of raw material, logistic problems, emissions, and overall process complexity that are inherent in their operations by doing the same. This paper presents the results of a literature review and analysis and conveys the challenges for adaptation and implementation of digitization and artificial intelligence (AI) in the cement and aggregate production industry.

Mar 2, 2022

By M. Adnan Goksel

A blast furnace test of approximately 5,000 tons of PelleTech Corporation (PTC) cold bond pellets was successfully run at Kaiser Steel Corporation (Kaiser) Steel Manufacturing Division at Fontana, California. The pellets were produced from mill scale, BOF dust and blast furnace flue dust. A 15 day base period, during which time the metallic burden was 2/3 heat indurated pellets and 1/3 sinter, preceeded the test. During the test period the metallic bur- den was 10% cold bond pellets, 56.7% heat indurated pellets and 33.3% sinter. A 15 day post test base period followed during which the PTC pellets were replaced by conventional pellets. The pellets were produced in the 3.C Semi-works Facility located on Kaiser property. The facility incorporates the Michigan Technological University Hydro-Thermal Agglomerating Process.

Jan 1, 1979

By A. S. Atkins

The interest in the use of micro- organisms in the leaching of sulphide minerals has been traditionally exploited as a scavenger process for the recovery of valuable metal by- products from waste ore dumps. Environmental concern on sulphur emission from conventional pyrometallurgical plants together with the cost of stack cleaning systems to comply with legislative control also indicate baccerial leaching to offer a low cost treatment for the processing of sulphide minerals. The paper describes the effect and limits of relatively coarse particles on the complete leaching of pyrite and its importance to the practical application in dump leaching operations of sulphide minerals. It has also been demonstrated that static leaching techniques have encouraging economic potential for process plant operations compared with agitated leaching systems.

Jan 1, 1984

By Liliana Rybarska-Rusinek, Aleksandr M. Linkov, Ewa Rejwer-Kosińska

Joined modeling of stressed state and induced seismicity is a means to join geomechanics with seismic observations. When applied to quantifying rockburst hazard, it provides, on one hand, estimations in terms of mechanics, such as stress concentration, and, on the other hand, in statistical terms of the risk analysis developed in mining seismology. The modeling became possible due to progress in computers and numerical methods. However, despite tremendous increase of computational abilities, the joined modeling is still quite time expensive. To make it available for wide use and real time simulations, there is need to reduce the time cost of its key stages: calculation of stresses, caused by mining, and simulation of seismic events, induced by these stresses. The present work aims to decrease the time cost. The stages are time costly because of the same reason, which is a very large number N (up to millions) of elements, representing rock structure, openings and flaws. This leads to immense computational complexity (roughly of order N2) of conventional accounting for pairwise interactions between the elements. The complexity may be notably reduced, when employing the fact that interactions decrease with growing distance between elements. Specifically, the fast multipole methods (FMM) avoid the complexity N2, by employing translations of far-fields from whole collections of sources. This reduces the complexity to the order 22, where p is the number of terms involved in a single translation, is the number of translations, and is the dimension of the quantity translated. Still, for conventional FMM, the complexity remains too high to routinely perform joined modeling of stresses and seismicity.

Apr 26, 2022

By F. N. Kissell

U.A. Mine Safety and Health Administration (MSHA) coal dust compliance data sometimes shows high silica levels at roof bolters. However, it is unclear whether this silica normally originates from the bolter itself or from other dust sources upwind of the bolter research studies to answer this question at individual mines have been conducted. However, operational practices vary from mine to mine thus, the information gleaned from any one study cannot be accurately extrapolated to describe silica dust sources in most mines. In this paper, three decades of bolter dust research are reviewed the results showed that, while inadequate maintenance on the bolter dust collection system can result in excessive dust, more likely reasons for high silica levels are inadequate ventilation of the mine entries being bolted and dust traveling downwind from the continuous miner to the bolter. Scrubbers on continuous miners may not be removing as much silica dust as expected. Mining Engineering, 2011, Vol. 63, No. 10, pp. 78-82. Official publication of the Society for Mining, Metallurgy and exploration, Inc.

Jan 1, 2011

By Gerald A. Zicg

The Sheep Creek project area lies between 15 and 20 miles north of White Sulphur Springs in west central Montana, on the southern flanks of the Little Belt Mountains. The Sheep Creek project is a joint venture in which Cominco American Resources, Inc., has a 50% operating interest and BHP-Utah International, Inc., has a 50% participatory interest. The property consists of over 40,000 acres of leased fee land and lode claims. Modern exploration of the Sheep Creek area began in 1973 and 1974, when Homestake Mining Co. examined the extensive Sheep Creek gossans with soil sampling, trenching, and drilling. Cominco American Inc. began exploration in the area in 1976. Between 1978 and 1985, Anaconda Copper Co., Exxon Minerals Co., and Freeport also conducted exploration programs in the area. In 1985, Cominco completed consolidation of the district, gained BHP-Utah International, Inc., as a joint venture partner, and the joint venture drilled the first significant copper mineralization on the property. Of six bodies of copper mineralization so far located, the best defined are an upper copper zone, which includes a probable resource of 4.5 million metric tonnes grading 2.5% Cu and 0.1 % Co, and a lower copper zone which includes a possible resource of 4.5 million metric tonnes grading 4% Cu. Exploration drilling of the property is in progress.

Jan 1, 1991

By Pratama Mochamad Rizki, Andika Satya

High-risk area in open-pit mining should always be monitored by the operational supervisor because of its nature. One of this type is the soft soil dump area. Due to the unstable bearing capacity of the soil, it’s highly possible for us to find cracks in the area. This paper aims to build computer vision which able to detect truck’s distance from safe limit allowed during dumping activity. The system will warn the truck’s driver if the truck has crossed that predetermined safe limit.

Jun 25, 2023

By Z. Sample, S. Kaushik

"INTRODUCTION Industries around the globe have been making significant advancements in recent years due to innovations in automation technology. With the implementation of modern automation technology, professionals in process automation or plant operations can expect significant and exciting change, and the mining and mineral processing industries are no exception. From 2000 to 2010, the International Council on Mining & Metals (ICMM) reported that an increased output and increased value of most metals has resulted in a rise in global metal and mineral process industries from $214 billion to $644 billion. [1] Since most productivity increases in mining and mineral process industries have been achieved through the ability to process lower grade ores with improved efficiency and larger equipment, these industries have begun to adopt advanced automation and control technologies. Despite a growth slow-down, the mining and mineral processing industries are poised for continued and sustainable growth and development due to an increasing demand for energy minerals and emerging technologies requiring minerals and metals previously not demand. However, as these industries becomes more automated, new challenges are arising on the horizon. DEMOGRAPHIC TIME BOMB John Payne from BP is credited with first using the term Demographic Time Bomb to describe the upcoming crisis in the process industry in finding experienced operations personnel. From a survey of 912 mining professionals, Stratum International found that a mere 0.4% of senior level candidates were between the ages of 25 and 34 and a similar proportion aged over 75 years. This indicates that there is both a deficiency of young skilled workers and a skilled workforce that is retiring earlier than the previous generation. Combined with data published by the US Department of Labor stating that the median age of the mining workforce is approaching 50 years old, this implies that these skilled mining and mineral process professionals are an aging population with irreplaceable knowledge and experience that are expected to retire in the next 5-10 years. While it is projected that the labor pool will be sufficient to fill open positions, the real question is if this young workforce will have necessary skill sets and experiences."

Jan 1, 2015

By W. Z. Choi

A combined size reduction- liberation model of grinding has been developed to predict the product size distribution for both free and locked particles. The model is an extension of the population balance model for size reduction. Locked (or composite) particles have been subdivided into discrete classes of different compositions to obtain more detailed information. The model has been tested on a sphalerite ore from Tennessee. Liberation data have been obtained using an areal scanning technique on microscope images of polished particle mounts.

Jan 1, 1985

By A. Kalogeropoulos, T. Michalakopoulos

The DEM has been used in several studies to numerically simulate the response of rocks to the cutting action with drag tools. In this research, the aim is to realistically simulate the rock material and the cutting process by controlling the grain interlocking of the numerical assembly and streamlining the calibration process while focusing on the cutting force and the failure mechanism.

Apr 1, 2023

By C. H. Pitt

A jet slurry apparatus has been constructed to test corrosive/erosive wear properties of grinding ball metal. Plain high carbon steel heat treated to a hardness of about 60 RC was used. Slurries of quartz and chalcopyrite ore concentrate were used as the jetting media. Weight loss due to pure corrosion was determined by the linear polarization technique and weight loss due to pure erosion was determined by jetting while cathodically protecting the sample. By comparing the total weight loss with the sum of the weight losses from pure corrosion and pure errosion it was found that there was a synergistic effect between corrosion and erosive wear. Erosive wear rates are given as a function of pH and mineral type.

Jan 1, 1984

By Raj K. Singhal

Canada produces close to 42 million tonnes of coal per annum of which some 38 million tonnes is produced by surface mining methods. The two Western Canadian provinces, Alberta and British Columbia, produce 31 million tonnes of coal by surface mining. These two provinces provide the bulk of the metallurgical coal for export. The geological conditions in the Western provinces particularly in the mountain region are complex. The coals are friable and the seams are steeply inclined, sheared, intensely folded and faulted. There may be as many as 15 to 20 coal seams present with true thickness ranging from 2.5 m to over 8 m. This paper reviews the surface mining methods used to extract such seams. The difficulties associated with steep seam and multiple seam mining of friable coal resulting in lower coal recovery, high dilution and the problem of cleaning fine coal in the wash plant have been highlighted.

Jan 1, 1984

By J. L. Whitlock

A mutant strain of Pseudomonas paucimobilis is utilized to effectively degrade and or remove 90-98% of cyanide, thiocyanate, toxic heavy metals and ammonia from a cyanidation mill process and mine discharge maximum of 21,000 m3/d (5.5 MGD). Homestake Mining Company?s biological wastewater treatment plant has been in full scale operation for over 2 years at the Homestake Mine in Lead, South Dakota.

Jan 1, 1987

By Kenneth Denton, Michael Cutts, Andrew Bursey, Eric Eisold

Phase III of the Orme Street Combined Trunk Relief Sewer project connects two existing 2.13 m diameter combined sewers to a new 3.66 m diameter relief sewer at 7locations along a 970 m alignment in downtown Atlanta. The alignment was enveloped by adjacent structures and utilities. The project was constructed below the groundwater table through compressible residual soil, rock and mixed face using a myriad of construction techniques, including compressed air NATM and jet grouting. Numerous design and alignment changes and accommodations for existing utilities and conditions were made during construction. The authors believe this to be the ?rst NATM project in North America utilizing compressed air tunneling.

Jan 1, 2003