Search Documents

By Layton C. Binon

Exploration budgets are commonly determined by "rules of thumb" such as a percentage of earnings or other fiscal measure. An appropriate exploration budget is the amount needed to achieve the goals of the company. It can be determined by discounting the income expected from achieved goals. Budgets for individual projects are determined in a similar manner except that risk of failure is included in the computation.

Jan 1, 1981

By A. D. Davis, C. J. Webb

Brohm Mining Co.'s Gilt Edge Mine in the northern Black Hills was a surface heap-leach operation that was active from the 1980s until 1999. Financing problems and acid drainage concerns at the mine were reported in the late 1990s. In February 1999 the Governor of South Dakota announced plans to request the US Environmental Protection Agency to help clean up acidic water at the mine and reclaim the site. In July 1999 the parent company of Brohm, Dakota Mining, filed for bankruptcy in Canada. Because of the bankruptcy and environmental problems, the State of South Dakota intervened and began water treatment. The mine was declared a Superfund site in 2000. Hydrologic issues include the potential for acidic drainage from the site. The mine is at the headwaters of Strawberry Creek, which drains into Bear Butte Creek. About four miles downstream, Bear Butte Creek loses its discharge to swallow holes in the karstic Madison Limestone aquifer, a regionally extensive and valuable groundwater reservoir. Other concerns at the site include treatment of acidic water in mine pits and a waste rock dump.

Jan 1, 2003

By Koehler Stout

Stopewall or room closure can be a problem in nining operations. In some mines, wall closure causes ore passes and nanways to collapse when they are enclosed in nine fill. When this phe- nomena occurs, heavy ground and, or, rock bursts frequently happen. Often, ground problems become progressively worse as mining in the stope block progresses toward the upper level. The sill and pillars in the level above may experi ence heavy ground and bursts. Sometimes the conditions get so bad in the stope that it is unsafe to mine the ore, so the stope is abandoned and the ore is lost.

Jan 1, 1980

By D. Ofiara, M. Lewis

Tunnel Boring Machines (TBMs) have been used in mining in decades past, but their use has been limited and sporadic. This has changed in recent years, with TBMs being used at Stillwater Mine, Grosvenor Coal Mine Slopes, Sirius Minerals potash mine, and more. These machines are all full face, circular TBMs—a design that has thus far have been unable to tackle a larger issue for mines: typically a flat floor is needed for mining vehicles to traverse. A novel type of non-circular boring machine is now answering the need to quickly reach underground ore bodies while cutting a rectangular profile in hard rock. This cross section allows for use of typical mine trucks and other rubber-tired mine vehicles. The machine uses disc cutters to cut the rock, and has a support structure similar to an open type TBM; however, the cutting geometry is entirely different. The machine is currently cutting an access tunnel at a silver mine. This paper reviews the design and operation of the novel noncircular tunnel boring machine, and describes possible future adaptations to provide safe, sustainable mine development.

Mar 2, 2022

By A. Newman, A. Brickey

A pesar de que parte del predominio de software de programación de producción a cielo abierto se puede explicar por la preponderancia de la minería a cielo abierto en todo el mundo, hay otros factores que han dado lugar a un retraso en el software subterráneo correspondiente. Explicamos por qué matemáticamente la programación de la producción subterránea es más difícil que su contraparte a cielo abierto y daremos pautas para la investigación en el campo de la programación subterránea.

Jan 1, 2014

By David Kress

Grinding mills, both autogenous and ball can be powered by several basic means. The three methods used today are girth gear drives, gearless drives and trunnion coupled reducers. This paper will focus on the first of these methods -girth gear drives. The girth gear drive has been used on thousands of mills which continue to operate successfully. These drives are noted for their simplicity and low cost. In the past, the horsepower capacity of girth gears has been slow to keep up with the horsepower increase required by the mill builders, particularly since the advent of the SAG mill. Gear manufacturers had capacity for 2000 HP mills in the 1950's, 5000 HP in the 1960's and 6500 horsepower in the 1970's. The 70's and 80's brought dual pinion girth gear drives which allowed mill sizes beyond 10,000 horsepower. Gear manufactures who could not keep up with the pace of the horsepower demands and the quality and reliability demanded by the mill builders and users have fallen by the wayside.

Jan 1, 1991

By Sean Warren, JOSEF BOURGEOIS

The potential of rockfall at open-pit mines presents a continuous hazard to mine workers and is typically mitigated by designing catch benches at empirically determined widths. The National Institute for Occupational Safety and Health (NIOSH) is working in conjunction with industry and academia to revisit and update current catch bench guidelines to better match acceptable risk tolerances for modern mining practices. To begin this process, a rockfall testing program was designed to gather empirical runout and bench catchment data at partnering mine sites in the Western United States. This paper presents a detailed description of each component of the rockfall testing program, including scouting and safety plan development, equipment requirements, synthetic rock development for uniform testing across varying bench configurations, local rock collection for testing of mine-specific geology, data acquisition during testing, and data processing. Additionally, this paper describes how the program has been updated over time according to lessons learned during initial rockfall testing.

Feb 1, 2024

By D. Bleazard

Barrick Goldstrike Mines, Inc. is actively involved in improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. The identification of equipment failure modes and the development of associated capital asset management practices can minimize failure consequences. Successful programs have included; alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle, resulting in an associated reduction to repair costs and equipment down time.

Jan 1, 1997

By D. B. Stephens

Milling operations throughout the world have created vast amounts of waste by-products, or tailings, which are often disposed on the land surface. The wastes may be disposed behind dams, on untreated ground, or on compacted clay or synthetic liners of impoundments and trenches. Often one of the principle concerns of environmental regulatory agencies is whether seepage from the waste pile could move through the vadose zone to the water table and possibly contaminate an aquifer. The seepage may be generated by the drainage of liquids initially deposited along with the tailings or by infiltrating meteoric water which leaches solutes from the tailings. The purpose of this article is to discuss some of the commonly held assumptions regarding storage of seepage wastes in the unsaturated zone. The significance of recent studies of water movement in dry climates which pertain to tailings site selection will be presented. The paper is relevant not only to seepage from impoundments at mill sites, but to many other fluid waste impoundments as well in part this article reinforces earlier work by Stephens and Siegel (1980) and an excellent review paper by McWhorter (1985). The present report addresses considerations in porous media; for a discussion of the effects of fractures and anisotropy in the unsaturated-zone, refer to the paper by McWhorter (1985).

Jan 1, 1985

By L. M. Gochioco

The U.S. coal industry is under-going dramatic changes to meet the challenges of the keenly competitive fuels market. The application of innovative technologies is needed to improve safety and to increase productivity in order to make coal more competitive as a fuel. As more coal companies shift into capital intensive longwall mining, there is a clear need to invest more in exploration before mine plans are made. Coal seam anomalies may create adverse mining conditions. The early detection of these anomalies could make the longwall mining safer and more productive through improved planning. A standard exploratory drilling program can provide only limited geologic information. The seismic reflection technique can be used to detect coal seam anomalies and is effective in reconnaissance surveying. Recent advances in the quality of coal seismic data have increased the success rate of seismic surveying. Therefore, surface seismic surveys, coupled with selective drilling, will come to play an integral role in coal exploration in the 1990s.

Jan 1, 1990

By Klaus Rabensteiner, Klaus Chmelina

"INTRODUCTION Urban tunneling is often related with special geotechnical risks. Typical causes are difficult (hydro)geological conditions, a very low overburden and the presence of critical and vulnerable (infra)structures in the influence zone of the construction (e.g. existing tunnels, roads and pavements, sewer pipes, gas and power lines, landmarked buildings, historic monuments). To manage these risks appropriately, an early detection and warning of unexpected behavior of the affected geotechnical objects ground and tunnel, as well as existing structures are mandatory. To accomplish this, the design and execution of a dense geotechnical monitoring program is of high importance. In more detail, this means specifying and performing a systematic and continuous acquisition, processing and analysis of monitoring data to support decision making. In recent years the development of new automatic sensors and (wireless) data transfer techniques and the general trend towards an automatic acquisition of monitoring data has led to an enormous increase of data production frequencies and volumes. In order to handle this data explosion efficiently, information systems and geo-databases have been developed and used successfully in many projects. They represent IT tools that support the different tasks of a given geotechnical monitoring program including data acquisition, transfer, check, processing, backup, analysis, distribution, reporting and, last but not least, alarming. Meanwhile, some tools already have developed the capability to connect to other theme-specific databases used in the project and, thus, serve as a central data management system for all kind of digital data produced. This makes possible the implementation of further useful functions and services supporting tunneling tasks such as machine control, tunnel simulation, geological prediction, process optimization, etc. where data from different engineering disciplines must be combined and processed in an integrated way. In the following chapters our aim is to describe how monitoring data management, geotechnical monitoring, alarming and reporting are organized and technically implemented at the metro project Cityringen in Copenhagen (Denmark). We want to highlight the specific role and tasks of the used tunnel information system in the project, and particularly inform on the most relevant challenges."

Jan 1, 2016

By G. J. S. Govett

Dwindling near-surface mineral reserves emphasize the need for the development of exploration techniques capable of greater depth penetration; geochemical techniques tradition- ally have been restricted to the search for deposits having at least a sub-outcrop expression. Rock geochemical techniques developed in Cyprus in 1967-1968 recognized anomalous conditions in volcanic rocks up to one mile from an ore de- posit. Research by the Exploration Geochemistry Group at the University of New Brunswick has shown that some massive sulphide deposits in New Brunswick have well-defined halos of major, minor, and trace elements in the host rocks extending up to 1,200 metres (4,000 feet) laterally along the same stratigraphic horizon, and up to 450 metres (1,500 feet) vertically in hanging wall rocks which apparently post-date mineralization; well-defined halos have also been found in foot- wall rocks. Some of these halos are readily identified as individual elements or as element pairs; others are so subtle as to be recognizable only through computer-calculated multivariate analysis. Research continues to extend the dimension of rock geochemical halos for regional exploration and for identification of more restrictive anomalous conditions which may closely define the location and extent of buried sulphide deposits.

Jan 1, 1975

By Johannes Jäger

"A composite shell lining typically consists of an outer permanent sprayed concrete shell, a water proofing layer and an inner sprayed or cast concrete shell. Composite shell linings become more and more popular and have been built recently on large scale infrastructure projects. Surprisingly there is very little published literature on the actual structural design of composite linings. As a consequence there is a lack of common understanding on how to design a composite lining structure. Composite action of the outer shell (primary lining) initially carrying short term ground loads and the “unloaded” inner shell (secondary lining) require nonlinear concrete modelling to be able to assess the bearing capacity of the composite lining structure adequately. The composite action of the waterproofing membrane and the inner and outer shells can be considered either by simplified closed form solutions or by numerical models. Strength and stiffness parameters of membrane and concrete govern interaction of inner and outer shell. This paper should contribute to understanding composite lining behaviour with focus on the bearing capacity at limit state by taking into account the actual loading history. Possible ways and concepts on how to deal with these topics are presented, however a broader discussion on limit states of the composite lining materials – also in the long term will be required to come to an agreement on composite lining design methodology. INTRODUCTION Composite Lining Technology Traditionally the construction of shotcrete lined tunnels incorporates primary and secondary linings, separated by a sheet or a sprayable waterproofing membrane. The primary lining shotcrete is considered to be structurally temporary and the secondary lining to be permanent, leading to designs which ignore the bearing capacity of the primary lining in permanent condition. There was general perception that the shotcrete lining installed immediately at the tunnel face, experiencing strains up to 1% and even cracking in the early age, combined with mesh reinforcement additional support measures like lattice girder, spiles and bolts cannot be considered as a permanent structure. But also former shotcrete mixes showed significant weakness with respect to durability suggesting a more temporary nature of primary lining shotcrete. On the other hand it was clear that primary lining shotcrete does not disappear, it may lose probably a certain percentage of its bearing capacity, but discounting any contribution from the primary lining at all was considered inherently conservative. There were different strategies to account for the risk of reduced durability and bearing capacity of the primary lining, either by selecting moderate ground loads for the secondary lining design, by assuming that some residual load will be carried by the primary lining. This approach is very much based on experience. Another more rational possibility is to assume that the primary lining degrades into a rocklike material, which is weaker than the primary lining shotcrete but still imparts some strength to the ground around the secondary lining, but does not need to comply with any concrete design codes any more."

Jan 1, 2016

By R. E. Scheffel

In February, 1976, Ranchers Exploration and Development Corporation obtained an option from Foote Minerals, Inc., to evaluate reprocessing of two uranium tailing piles. Foote received ownership of the Naturita and Durango tailing piles in 1967 through the purchase of Vanadium Corporation of America. The option was exercised in November, 1976, after initial testwork proved that a viable extraction technique existed. Preparation for production at Naturita began immediately with engineering and en¬vironmental permitting proceeding simultaneously. Production began in December, 1977, just 22 months after acquisition of the property and-was completed 17 months later.

Jan 1, 1981

By Charles W. Bauer

Most of the aluminum produced in the United States today is derived from foreign bauxite deposits. Earth Sciences, Inc. initiated a program to evaluate domestic non-bauxite sources for alumina in the 1960's. In the initial evaluation of alunite, domestic resources were not sufficient to support development. An exploration program led to the discovery of large deposits of alunite in Utah and several other western states. Identification of alunite is difficult as both its physical and chemical characteristics are similar to the minerals with which it is associated. Most of the significant alunite deposits in the western United States are replacement type deposits. These deposits have formed as a result of hydrothermal alteration of volcanic, sub-volcanic, and igneous rocks. Typical alunite deposits contain between 30% and 50% alunite between 50% and 70% quartz with minor amounts of other minerals. Four mineralogical zones are common in these systems. They include a siliceous zone, a quartz-alunite zone, a kaolinite zone and a chlorite-montmorillonite zone. Total U.S. reserves of alunite were estimated at 20 million metric tons (at 30% alunite) by the U.S. Bureau of Mines in 1941. Here recent work by the U.S. Geological Survey estimates reserves of 252 million metric tons and potential resources at 1.4 billion metric tons. Reserves and resources estimated for 23 properties on which field work has been done by ESI are considerably higher. Most of these properties have reserves and potential resources of several hundred million metric tons. The combined demonstrated reserves at these properties are estimated to be about 650 million metric tons. Inferred reserves are estimated at 2.5 billion metric tons and potential resources at 8 billion metric tons. It appears that the U.S. has sufficient reserves and resources for alunite to be considered as a potential non-bauxite source of alumina.

Jan 1, 1980

By Todor P. Stefanov

The thermal draught within ventilation networks of underground mines depends to a great extent on the shafts depths and degree of change of ventilating air density. When the topology and space orientation of a ventilation network are constant, the dynamics of thermal draught is determined mainly by the variations of the heat- and mass-transfer processes in the openings. This conclusion follows from the well known basic theoretical notions about the thermal draught-aerostatics and thermodynamics [1]. Quantitative evaluation about the influence of heat- and mass-transfer processes on dynamics of thermal draught could be made through: direct mine measurements, special experiments and with the aid of mathematical models. The first two methods produce sufficiently accurative results, however it is very difficult to perform such studies, particularly when these processes are evaluated within a large scope and multifactor aspects. Mathematical models of thermal draught allow to overcome easily these difficulties. The degree of accuracy of results, obtained by this method, depends to a great extent on the degree of approximation achieved by the model to the real heat- and mass-transfer processes. In this paper, with the aid of Bulgarian developed method, algorithm and computer program V WT-4 - for complex evaluation of ventilation parameters in active mine ventilation networks [2], the authors investigate some changes in the thermal draught. Basically, the method is an iterating evaluation of an open set of equations, which represents relationships between the following basic parameters of a mine ventilation network: [ ]

Jan 1, 1980

By Rudrajit Mitra, Erik Hulthen, AARTI SORENSEN, TOBIAS HARTMANN, ELISABETH CLAUSEN

There has been an ongoing debate on how to transform engineering education to better prepare students for today’s professional world that is characterized by increasingly complex problems and challenges that engineers are tasked with upon entering the industry. While numerous publications have addressed possibilities of how experiential, problem-based, project-based and active learning can be integrated into the engineering curriculum, there has been little attention on mining engineering with respect to adopting this approach. This paper addresses the possibilities of integrating entrepreneurship education into mining engineering programs in order to foster discussion among academics from mining engineering on how to infuse value-creation experiences across the curriculum on a course, program and departmental level.

Sep 1, 2022

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain < 0.3% Cr2O3, and chromite is almost always less than 50 um in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratifonn and alpine complexes tend to be either ore grade (> 25% Cr203) or very low grade (< 2% Cr203); intermediate rocks are scarce. In most complexes large tonnages exist only in the < 2% Cr2O3 group and the composition of the chromite is commonly unsuitable for metallurgical use. Some nickel laterite districts contain more than 108 tons of material with 2.0% to 5.5% Cr2O3, and hence, chromium could be a byproduct of nickel in some laterite districts.

Jan 1, 1982

By S. L. Crouch

The general term "coal mine burp" refers to the sudden and violent failure of in situ coal. Coal bumps occur in most countries where coal is worked by underground methods, and are related to both geological factors and mining tech¬niques. Although no single set of circumstances is solely responsible for causing coal bumps, it is generally agreed that at least one of five conditions is necessary in order for then to occur: 1,2,3,4 (1) the depth of cover exceeds 500-ft., (2) the overlying strata are relatively strong and stiff, (3) the coal is structurally strong, (4) the floor does not heave readily, and (5) the mining method produces high stresses over a large area of the seam. Except for the last, these conditions relate to geological factors that are impractical to control. Consequently, methods of controlling or minimizing the occurrence of coal bumps usually are concerned with mining techniques. Coal bumps have been successfully controlled by both longwall and &apos;yielding pillar&apos; mining systems 4. The longwall system is particularly effective in controlling bumps, but does not eliminate them completely, especially in strong coal seams being worked at comparatively great depths, say in excess of 2000-ft.5. Under such conditions, auger drilling or water infusion often prove helpful 5,6. These techniques are used to destress or otherwise alter the mechanical properties of the coal in an attempt to shift the peak "abutment pressure" away from the immediate vicinity of the face. Under &apos;normal&apos; conditions, however, it can be expected that the coal near the face will be crushed under the prevailing high stress conditions and that the peak abutment pressure will automatically be shifted into the solid coal. In this context, coal mine bumps can be characterized as unstable releases of energy associated with successive yielding of portions of the coal seam with progressive mining. Longwall and yielding pillar mining systems are effective in controlling coal bumps because they ordinarily do not allow the zone of peak abutment pressure to become &apos;surrounded&apos; by destressed coal.

Jan 1, 1973

By A. I. Johnson

This paper describes," the application, of a modular or building block approach to the analysis, design, and control of complex mineral treating processes. The main purpose of the paper is tutorial, to show the reader how such processes can be modeled using a modern digital computer" and, not to discuss in any detail the results that may be achieved in such studies. It is proposed that, the main techniques be illustrated by reference mainly to the Bayer process for alumina extraction and purification; in cooperation with the Aluminum Company of Canada Ltd. the author and his Colleagues at McMaster University and their students have studied this, process as a means of applying new computer techniques to extractive metallurgical processes. The plant described was studied by the author and his colleagues as a senior undergraduate project in cooperation with the Aluminum Company of Canada. It is one of several studies that have been carried out with Canadian industry. (1)

Jan 1, 1972