Search Documents

By Joseph Padgett

Of all the fossil fuels produced in the U. S., coal is by far the most abundant. U. S. reserves amount to an estimated 1.5 trillion tons, 2,500 times the 600 million tons produced in 1970. Although it would not be possible to recover all of this coal economically with current mining technology, a significant portion would be available given the proper circumstances. With existing technology, approximately one-eighth of these reserves is accessible, an amount which would last for several hundred years at the 1970 level of production. On the face of it, this substantial reserve should go a long way in meeting the Nation's energy needs. But coal offers special problems. As additional coal is mined and then burned, there are increased costs to the Nation's land, water, skies, and health. Hence, coal poses a dilemma because of its dual status as one of our most abundant domestic fuels and as one of our major sources of environmental degradation. Against the benefits that would be chalked up in the areas of national security, balance of trade, and economic well-being from the increased use of coal, we must enter on the debit side of the ledger the increased environmental cost. This paper reviews the use of U.S. fossil fuel, the drawbacks of coal as an energy source, the means being developed to overcome these drawbacks, and the background behind the present sulfur emission regulations relative to coal combustion. It also discusses in detail the Federal Environmental Protection Agency's (EPA's) current policies to ensure the continued use of coal as a major source of energy for fossil-fuel fired power plants.

Jan 1, 1973

A digital computer program has been developed to mathematically simulate the effect of limited changes in feed rate on the grinding circuit of an operating mill. The data on which the program is based was supplied by the staff of the mill in question. Samples taken around the complete grinding circuit were analyzed for solids content and particle size distribution for two feed rates. Matrix models were used to represent the grinding units: rod mill and pebble mills. Parameters for these models were computed using a method developed by Mular(l). Classifier parameters were computed by the Powell search method(2) for the Plitt model (3) . The simulation program, which permits the computing of the size distributions in the circuit resulting from the changes in feed rate between the two measured values, assumes that a linear relationship exists between the corresponding parameter coefficients. The program uses an iteration method to bring the simulated grinding circuit to a steady-state material balance for any specified' feed rate between those measured. The program is, in addition, extremely fast and economic in computing time. The results show that the simulations are not everywhere consistent with practice. For example, higher feed rates on simulation predict finer products. These errors are shown to be attributable to anomalies in data gathering techniques. An improved sampling procedure for grinding-circuit data gathering is suggested for future simulations of this type. It is concluded that the

Jan 1, 1971

By Kerry Burns

Contrary to active subsidence, which occurs concurrently with mining operations, or is completed within a few days following coal extraction, delayed subsidence may take many years to appear at the surface after coal mines are abandoned. There are two principal morphological types of delayed subsidence: troughs, which are shallow depressions, and sinks, which are steep-sided crown pits. Both types are damaging to surface structures, and a variety of methods have been introduced to deal with the problem, ranging from subsidence insurance to site restitution. In planning insurance or restitution measures, a predictive model is of value in estimating the magnitude of the problem and the size of long-term budgetary commitments. Only one model is known, which was developed for the Bureau of Mines by GAI Consultants of Monroeville (l,2,3). The GAI model is presented in qualitative terms. This report develops a formal basis for the model and tests a numerical implementation on one of the best-described study areas, Allleqheny County in Pennsylvania.

Jan 1, 1982

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By J. Kulczycka

Poland in time of transition had been dealing with the remnants of the previous regime ? particularly in the field of environmental protection. The burden left was tremendous and there was a need for fast and effective tools for improving the environment. The idea of environmental protection had been supported by the introduction of a new environmental policy that underlined the importance of sustainable development in industry in the beginning of 1990s. This policy introduced high environmental fees and fines ? a concept not very popular in Europe in that time ? and good only for a country in transition to boost the protection of the environment. While this policy had its role to play, its role is now completed. It is time to move forward, especially when these environmental charges affect the international competitiveness of industries so much, and at the same time have virtually no influence on environmental protection investments any more.

Jan 1, 2005

By David J. Hammel

This chapter will summarize some of the important applications in the geotechnical (pit slope, spoil pile and tailings stability, and hydrology), the environmental (including reclamation), and equipment selection and analysis areas. Virtually all aspects discussed are applicable both for planning of new mines and for evaluating existing operations. Probably the most influential item which has affected the areas discussed in this chapter and possibly most areas discussed in this book is and will continue to be, in the next decade, the myriad federal and state environmental, safety, and reclamation regulations affecting new mine development and continued operation of existing properties. Computer applications have been and will continue to be instrumental in assisting in planning to meet the challenges of the requirements dictated by these regulations.

Jan 1, 1979

By G. Ofori-Sarpong, A. -S. Adam, R. K. Amankwah

"In the application of the BIOX® technology, high tailings grade (2-16 g/t) may be generated with a decrease in overall gold recovery, which sometimes make it economically unattractive. This paper investigated the causes of the high tailings grade by using samples from the Bogoso BIOX plant. Partial chemical analysis, diagnostic tests and cyanidation optimisation studies were conducted to invoke understanding into the high tailings grades. Diagnostic study on the tailings showed 48.34% of gold in carbonaceous matter, 17.12% in quartz, 13.40% as liberated gold, 11.51% imbedded in sulphides and the remaining 9.65% in carbonates. Optimum cyanidation recovery of 90.4% was established for the BIOX concentrate at 7 kg/t NaCN, 40-50 g/L activated carbon and residence time of 40 hours. The recovery was sensitive to carbon and cyanide concentrations but additional cyanide was not economical. High preg-robbing indices of 72.7% and 64.4% were recorded for the BIOX product and the flotation concentrate respectively. This confirms the inability of the BIOX process to deactivate carbonaceous matter, which remains a serious precursor for low overall gold recoveries and high CIL tailings. INTRODUCTION Gold ores may be broadly classified as refractory and non-refractory. Non-refractory ores are easy to treat but refractory materials require complicated flowsheets for metal extraction (Hausen and Bucknam, 1985; Schmitz et al, 2001; Marsden and House, 2006). As near surface non-refractory gold deposits are getting depleted, the increasing price of gold and increasing demand for gold, have encouraged many gold producing companies to treat refractory ores for gold recovery. The refractory behaviour of these ores may be due to the presence of sulphides, tellurides, cyanicides and/or carbonaceous matter. Refractory ores do not respond well to conventional cyanidation as the gold is either occluded by or in solid solution in sulphides, or is in association with cyanicides (Marsden and House, 2006). Further, carbonaceous matter preg-robs gold during leaching (Osseo-Asare et al, 1984; Hausen and Bucknam, 1985; Schmitz et al, 2001). The two major causes of refractoriness are the presence of sulphides and carbonaceous matter, and these render the ore double refractory (Nyavor and Egiebor, 1992). Oxidative pre-treatment processes such as high pressure leaching/oxidation; biological oxidation, ultra-fine grinding and roasting are required to render refractory ores amenable to conventional cyanidation (Marsden and House, 2006). Biological oxidation, however, has become the preferred pre-treatment route because it is more environmentally friendly and convenient even where only partial oxidation is required. Comparative tests have demonstrated that bioleaching can achieve the same or better results than roasting or pressure leaching in terms of gold recovery (Yannopoulos, 1991; Brierley, 1997). Further, biological treatment processes are more cost-effective, environmentally friendly and safer."

Jan 1, 2017

By Kendall Y. Onstott

The paper presents the results of a plant test using WEMCO 1 + 1 enclosed flotation machines for inert gas (nitrogen) flotation of by-product molybdenite from copper sulfide concentrate. Copper depressant consumption in the rougher flotation stage was reduced by 68% as reagent consuming oxygen was removed from the flotation air. Unlike other nitrogen flotation systems used in the industry, nitrogen is recovered above the flotation cells and from froth in tails and concentrate streams and recycled, resulting in minimal nitrogen makeup requirement.

Jan 1, 1984

By David Jurich, Ed Perko, Jacob Prezkuta

Numerous Colorado mountain tunnels that date to the late 1800s convey water to the farming and urban communities of the eastern Front Range. Repairs to these remote facilities, often located in public lands at altitudes of 11,000 feet or more, require detailed planning, close coordination with multiple agencies, and creative execution. Issues and solutions discussed include designing repairs in undocumented ground and support conditions, logistical challenges, work in a short summer construction window, stabilization of historically signicant structures, and proect delivery strategies. xamples that illustrate early contractor involvement, exibility in design, and construction solutions are presented.

Jun 23, 2024

By V. T. McLemore

"Lindgren (1933) defined a belt of alkaline-igneous rocks associated with large quantities of gold and rare earth elements (REE) that extends from Alaska and British Columbia southward into New Mexico, Texas and eastern Mexico. The North American Cordilleran alkaline-igneous belt since has been exploited for numerous types of mineral deposits. In New Mexico, Mid-Tertiary alkaline to calc-alkaline rocks are found with seven types of deposits in these districts: (1) polymetallic epithermal/mesothermal veins, (2) gold-bearing breccias/quartz veins, (3) Cu-Au, Au and Mo porphyry deposits, (4) skarns and carbonate-hosted deposits, (5) iron skarns and replacement bodies (with some gold), (6) gold placers, and (7) Th-REE (with some U, Nb) epithermal veins. Some of New Mexico’s largest gold and REE deposits are found within this belt. Their origin is not well understood, but a compilation of new data (age dates, isotopic and chemical analyses) allows for a better understanding. The diversity of igneous rocks and associated mineral deposits along this belt suggests that this region is characterized by highly fractionated and differentiated; multiple pulses of magmas and involves both upper mantle and lower crustal sources. Once magmas and metal-rich fluids reached shallow levels, local structures and wall rock compositions determined distribution of and final style of intrusions and resulting mineral deposits. INTRODUCTION Lindgren (1933) was one of the first geologists who noted that a belt of alkaline-igneous rocks extends from Alaska and British Columbia southward into New Mexico, Trans-Pecos Texas, and eastern Mexico (Fig. 1) and that these rocks contain relatively large quantities of gold, fluorine, zirconium, rare earth elements (REE), and other elements. Since then, the North American Cordilleran alkaline-igneous belt has been explored and exploited for numerous types of mineral deposits, especially gold. The North American Cordilleran alkaline belt is a north-south belt of alkaline igneous rocks and crustal thickening, roughly coinciding with the Great Plains physiographic margin with the Basin and Range (Rio Grande rift) and Rocky Mountains physiographic provinces (Mutschler et al., 1985, 1991; Bonham, 1988; Thompson, 1991a; Richards, 1995; McLemore, 1996; Jensen and Barton, 2000; Kelley and Luddington, 2002). Deposits within this belt have produced significant amounts of gold in the United States and Canada and include Cripple Creek, Colorado (702 metric tons of gold production), Black Hills, South Dakota (235 metric tons gold production) and Landsky-Zortman, Montana. In New Mexico, the North American Cordilleran alkaline belt extends from the Sangre de Cristo Mountains near Raton, southward to the Cornudas Mountains, in the northern Trans-Pecos alkaline belt (Fig. 2). The alkaline-igneous related mineral deposits in New Mexico have been referred to as Great Plains Margin (GPM) deposits by North and McLemore (1986, 1988) and McLemore (1996, 2001). Alternative classifications by other workers include Au-Ag-Te veins (Cox and Bagby, 1986; Bliss et al., 1992; Kelley et al., 1998), alkalic-gold or alkaline-igneous related gold deposits (Fulp and Woodward, 1991a; Thompson, 1991a, b; Bonham, 1988; Mutschler et al., 1985, 1991; Richards, 1995), porphyry gold deposits, and the North American Cordilleran belt of alkaline igneous rocks (Woolley, 1987; Mutschler et al., 1991)."

Jan 1, 2015

Just 104 km (65 miles) from Phoenix, AZ, Rio Tinto hopes its new Resolution Copper Mine will be a showcase for the Rio Tinto management philosophy. Its goal is to have a net positive impact. In every place that Rio Tinto mines, it wants to be able to have an overall beneficial effect on the local community, environment and economy. ?We?re constantly working to understand our impacts, to understand how to minimize our impacts and understand how to mitigate those impacts,? said Resolution Copper Mining chief executive officer David Salisbury, from the global headquarters of Rio Tinto Minerals in Green-wood Village, CO.

Jan 1, 2010

By Nick Tessitore, Ryan Marsters, Alex Warren, Dylan Fawaz

The West Gates Deicing Industrial Waste Pond Expansion project at Denver International Airport seeks to expand utilities to accommodate additional terminal gates. The project includes six tunnel crossings beneath taxiways and runways with lengths ranging from 239 to 2,025 linear feet. Excavation methods include shielded tunnel boring machines and steerable auger boring. Designed initial support includes liner plate, steel ribs and lagging, steel casing, and Fiberglass Reinforced Pipe and ranges in size from 24" to 132". This paper will discuss challenges associated with the overall layout and design of the project, including contingencies to protect critical infrastructure. In addition, a construction update is provided.

Jun 23, 2024

By Marcel F. DeGuire

Pilot plant operations are described for the treatment of manganiferous zinc concentrates from the Gamsberg ore deposit in South Africa via conventional electrolytic zinc processing. Two methods were employed for the control of excess manganese ions in the pilot plant electrolyte involving (1) chemical oxidation and (2) anodic oxidation. The chemical oxidation method for manganese control was very successful. It also was found that the addition of manganese dioxide ore was not required for oxidation of ferrous iron during the neutral leach or jarosite precipitation steps. A new method (JAR process) for iron removal also was tested in the pilot plant.

Jan 1, 1978

By M. S. Klima

This paper will detail the work that has been done in 1990 and 1991 at the Pittsburgh Energy Technology Center (PETC) on the development of the U.S. Department of Energy's (DOE) patented Micro-Mag Process. This process entails the use of a micronized-magnetite (minus-10 microns) and water mixture for cleaning fine coal (minus-600 microns) in a cyclone, along with the production and recovery of the magnetite. Emphasis will be on the results from micronized-magnetite recovery testing using both conventional wet-drum and high-gradient magnetic separators in which several key operating conditions were varied including feed percent solids, magnetite-to-coal ratio, magnetite grade, and feed rate. Also presented will be selected results from testing done on a 76-mm diameter cyclone at a relative density of 1.50 showing the effects of operating pressure, magnetite grade, and medium-to-coal ratio on separation efficiency. In addition, two methods for producing micronized magnetite, along with the corresponding size distributions, will also be discussed.

Jan 1, 1992

ITEC Environmental Colorado has begun reprocessing the tailings from old mining sites near Boulder, CO. And if the technology behind ITEC's pilot project at Gold Hill proves successful and profitable, the company plans to launch similar reprocessing operations in other parts of the state. The pilot project is under the watchful eye of state and federal authorities. They hope the technology becomes the answer to cleaning up old mining sites throughout the West. Remining and environmental cleanup on an economic basis, then, are ITEC's hopes in one the most environmentally conscious counties in the state. Clean up the mine dump sites and recycle the land, for a profit. In June 1998, ITEC Mineral Inc., ITEC Environmental Colorado's Canadian parent, acquired the Gold [ ] Hill Mill facility in Boulder County. Included in the acquisition was 4.4 hm2 (11 acres) containing the Gold Hill Mill and 283 hm2 (700 acres) of additional properties adjacent to the facility. ITEC estimates that there are about 910 kt (1 million st) of dump rock in the area. That is enough to make the operation viable. ITEC will sell the metals recovered through its reprocessing operations. However, due to low metals prices, ITEC is not expecting to make much money on the recovery of precious and base metals. Instead, the company plans to resell the reclaimed land for residential and commercial development or open space. The Gold Hill Mill site is the first of 17 sites in Colorado that ITEC Mineral hopes to clean up and recycle the land. Most notable among the sites is the historic Central City/Black Hawk mining district, which ITEC believes holds considerable potential. The Gold Hill Mill is located 14 km (9 miles) west of the city of Boulder and less than a half mile from the small town of Gold Hill. The mill was. last operated in 1992. The operation was forced to close that year due to environmental and cash flow problems. Gold Hill is in the middle of a region with more than 32 Mt (35 million st) of mine tailings. Independent geologists have' established the average grade of the Gold Hill mine tailings to be 4.5 to 5.3 g/t (0.13 to 0.155 oz/st) of gold and 28 to 44 g/t (0.83 to 1.29 oz/st) of silver. According to these studies, the Gold Hill mine tailings are five times richer in precious metals than the tailings of the Norebec Manitou property in Canada that ITEC is also remining, reclaiming and restoring. Upon acquiring the mill, ITEC undertook a refurbishing program that included adding a second ball mill. This increased the Gold Hill Mill's capacity to 180 t/d (200 stpd). The operation employs 15 people. "The Gold Hill Mill site will demonstrate the efficiency of our integrated remining, reclaiming and restoration process," said Maxine Stewart, president of Denver, CO -based ITEC Environmental. "The abundance of similar mine sites in Colorado presents a number of opportunities to bring the benefits of the ITEC system to other communities around the state." Holly Huyck is technical advisor to the Clear Creek Watershed Advisory Group. She said: "ITEC is cleaning up an orphan mine site that otherwise would continue to contaminate the Boulder Creek watershed with acid and excess metals. This is a win-win situation: ITEC gains marketable minerals while it reclaims mined land and helps to improve the watershed."

Jan 1, 1998

By Stanley O. Reichert

At nuclear facilities, three types of radioactive waste must be managed: (1) high-level liquid waste containing fission products from the chemical separation of irradiated uranium, (2) low-level condensates from the concentration of the high-level waste, and (3) dry solids such as obsolete process equipment, spent ion exchange resins, and irradiated metal scrap. The geological and environmental characteristics of a site are important considerations in planning the waste management program. At the Savannah River Plant, low-level liquids and dry solids are safely and economically placed in the soil where the geologic and hydrologic conditions are favorable. Within the general area where the waste originates, studies are made to locate seepage basins and burial grounds in the most favorable sites: (1) soils should have a high ion exchange capacity and moderate to low permeability, (2) the water table should be deep, and (3) burial sites should be relatively distant from the nearest flowing stream.

Jan 1, 1968

By J. Seifert, L. Hunter, P. W. Conrad, S. Rosenthal

"The goal of the protocol for reclaiming in-pit tailings ponds to exceed federal and state regulations was to develop a series of steps that can be followed to design, operate, and reclaim a tailings disposal pond that will develop into grazing land with a wetland for open pit sand mines in warm dry climates. By incorporating a wetland into the reclamation design, the post mining land use gives back to both the wildlife as a source of water as well as providing for a diverse range of post mining land use including but not limited to livestock grazing and ranch land use. An example design was completed using this protocol to demonstrate how the protocol can result in in a well-designed, reclaimed tailings disposal pond. BACKGROUND In an industry plagued with decaying historic mine sites, the public’s perception of mining appears to be poor. While modern mines are closely monitored and generally managed by ethical professionals, history still influences how the public perceives the mining industry. From collapsing abandoned underground workings to historic tailings dam failures, the failure to account for the environment in the past seems to affect public perspective on mining today. In a 2013 “Opinion Former Survey,” a survey conducted through interviews with a diverse range of stakeholders in various gold companies, it was noted that the most serious challenges facing the mining industry were environmental concerns and the permitting challenges associated with them (Council). In another article, this time focusing on Australian citizens and their perspectives of the mining industry, it was found that the majority of those surveyed had a big concern over the environmental impacts of mining especially when it comes to water quality and quantity (Scan). The statistics portrayed in these articles illustrate that today’s mining engineers needs to make more of an effort to change the public’s perspective of mining by being more environmentally aware. These engineers should be continuously asking themselves what they could be doing better from an environmental perspective to ensure that history is not repeated and that natural resources are used as efficiently as possible."

Jan 1, 2018

By Hugh Jones

Mine planners are challenged to hold two seemingly opposing objectives: maximizing the mine?s operational efficiency while minimizing post-closure impacts. One of the most effective approaches to meet these objectives is to plan for mine closure from the start. Mine closure is typically viewed as the process that happens in the period of time when the operational stage of a mine is ending and the final decommissioning and mine rehabilitation is being undertaken. In reality, it is a continuous series of activities that begins with preplanning prior to the project?s design and construction and ends when long-term site stability is achieved and a self-sustaining ecosystem is established. Putting this model into practice as early as possible can significantly reduce the financial burden of mine closure and rehabilitation.

Jan 1, 2011

By Rodney L. Stone

As part of an overall laboratory and plant test program to determine mixing and other techniques relating to the more economic use of bentonite as an iron ore pellet binder, a settling test was developed for measuring the bentonite content within a pellet or within a batch of pellets. Between pellet batches, each containing a different level of bentonite, the dry fracture load is directly proportional to the bentonite content between pellets of the same batch, however, the fracture load is inversely proportional to the bentonite level; this is explained by a negative correlation between a pellet's size and its bentonite content and the fact that larger pellets can withstand a higher fracture load than the smaller.

Jan 1, 1968

By S. C. O?Brien

This paper develops the procedure for simulating the special locked-cycle Work Index laboratory test using the kinetic parameters obtained by conducting standard size-mass balance (SMB) grinding tests and presents the results for three materials - quartz, a taconite iron ore and a bituminous coal. It was found that the WI could be determined by simulation; however, if a material breaks abnormally, a full description of its abnormal breakage is necessary. It was also found that the sensitivity of the WI test procedure to the sieving process and the estimating of the 80% passing size of the sieve undersize is sufficient to question the practice of quoting a WI to two or more decimal places. Finally, if a material grinds abnormally in the Work Index mill, then the WI test should not be conducted.

Jan 1, 1987