Search Documents

By David Chastka, Isidro Rivera, Shawna Von Stockhausen, Idit Zarchi

The City of Santa Cruz Water Department is replacing the existing Newell Creek Dam inlet/outlet works at Loch Lomond Reservoir in the San Lorenzo Valley. The project will improve the City’s overall operational efficiency, improve system performance, and improve the safety and reliability of storage for the City’s drinking water supply. The project comprises new inlet works* (three new inlets that control and convey flows into and out of the reservoir, and an intake control building), an inlet/outlet tunnel with a 48-inch conduit to convey flows into and out of the reservoir, and a new outlet structure at the toe of the dam. The outlet structure includes a release point for energy dissipation of emergency drawdown flows, a connection to Newell Creek Pipeline, and beneficial releases into Newell Creek. The project also includes a new dam seepage collection and monitoring system and appurtenant structures such as a culvert bridge over the spillway plunge pool to improve access to the new outlet. Notable complex project components include in-water work to connect the new intake shaft pipes to the three new inlets. The project includes one major milestone with a work window regulated by environmental permits that could only be amended/ extended with approvals from those agencies. If not met, the milestone work would have caused significant delays (potentially up to one year) to the project.

Jun 13, 2021

By G. Ahuja

Tests were conducted to investigate the effects of cyclone geometry, operating conditions, and particle size on magnetite classification. The effects of these parameters on the partition curve for narrow size fractions were studied using a 25mm diameter cyclone cleaning -150 µ m coal. Additional tests were run to investigate the effects of geometry and operating conditions on the slurry, solid, and water splits. The relationship between the relative density of the underflow stream and the relative density of separation was also investigated. This paper presents the results from this study.

Jan 1, 1994

By Alan Bauer

In recent years there has been increasing interest in employing the technique of explosive casting in strip mines. Explosive casting, applied to dragline mining, describes the procedure whereby the overburden is horizontally displaced by blasting causing a portion of the material to be thrown into the previously mined cut. Therefore, it is not necessary to subsequently excavate this waste with the stripping equipment. In addition, allowing the overburden unrestricted movement during the blast most often results in improved fragmentation and enhanced machine productivity. The method is receiving attention because the capital and maintenance costs of stripping equipment has risen rapidly in relation to explosives costs. Improved productivity is necessary to maintain unit costs at an acceptable level.

Jan 1, 1983

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the bubbles, water, and ore, selectively attaching these bubbles to the hydrophobic mineral's surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. The rapid flotation system was evaluated for beneficiation with a western porphyry copper ore containing 0.67 pct copper, and a phosphate-bearing amine flotation tailings sample containing 9.5 pct P2O5 in a quartz matrix. Over 88 pct of the copper was recovered from the ore in a rougher concentrate containing 5.9 pct copper at a rate 7 times faster than conventional flotation. Sixty percent of the quartz in the phosphate-bearing sample was floated at a rate 4 times faster than conventional flotation. The unfloated product retained 80 pct of the phosphate in a l6.9-pct P2O5 concentrate.

Jan 1, 1993

By Robert W. Curtis

Kaiser Aluminum & Chemical Corporation's (KACC) entrance into the alumina market began in 1946 with the purchase of a small plant in Baton Rouge. Louisiana. Since that time KACC has been involved with the design, construct; on, and operation of many alumina plants around the world. One of these plants is located in Gramercy, Louisiana. The Gramercy Works is a multiplant installation consisting of an alumina plant, a caustic-chlorine plant, a petroleum coke calciner and a fluorochemicals plant. Each of these plants require their own specific environmental control programs to abate pollution. Kaiser has made significant progress through the years on their own initiative in pollution control. But many new challenges have been and continue to be created with the enactment of environmental laws. The 1970 Clean Air Act Amendments, the resurrection of the old "Refuse Act" in 1970 and finally the 1972 Federal Water Pollution Control Act Amendments prompted the formulation of our current philosophy towards the abatement of pollution. Since the formulation of these complicated pieces of legislation, others equally complicated, have come to being. The Federal Insecticide, Fungicide and Rodenticide Act as amended by the Federal Environmental Pesticide Control Act of October, 1972, the Toxic Substances Control Act of 1976, the Solid Waste Disposal and Resource Recovery Act of 1976 and the Safe Drinking Water Act sighed in December of 1974 have all contributed to the challenge for an alumina plant to meet regulatory constraints. However, this paper will only discuss the alumina plant?s environmental programs designed to meet compliance with air and water pollution legislation. At the Gramercy Alumina Plant, over $25 million has been spent for pollution control since 1969. The Gramercy Plant is a prime example of KACC's commitment to meeting the environmental challenge.

Jan 1, 1978

By Donald L. Freed

Design, development, factory test, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, and final machine configuration are reviewed. The AES is designed to overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1977

By M. A. ENCINAS-ROMERO, G. TIBURCIO-MUNIVE, P. GUERRERO-GERMÁN, M. M. SALAZAR-CAMPOY, J. L. Valenzuela-García, L. S. QUIRÓZ-CASTILLO, J. R. PARGA-TORRES

Simultaneous alkaline pressure oxidation and sodium cyanide leaching treatments on a pyritic ore from Mulatos Mine located in Sahuaripa, Sonora, Mexico, were carried out. Mineral characterization, agitated leaching, hot cyanidation under atmospheric pressure conditions, simultaneous moderated pressure oxidation and leaching, and kinetic tests results are shown. The modified variables were temperature, pressure, and cyanide concentration. Characterization indicated that pyrite was the main mineral. Simultaneous pressure oxidation and leaching experiments were conducted in a temperature range of 40 to 80 °C, an oxygen pressure range of 87.5 to 200 psi, and cyanide concentration range of 0.8 to 1.2 weight percent in a 2-L Parr pressure reactor. Dissolution rates of 81 to 86 percent were achieved under the following conditions: 87.5 psi, 80 °C, 0.8 weight percent NaCN and processing time of one hour.

By Raymond E. Langen

Uranium exploration in the Powder River Basin of northeastern Wyoming has been intensive since 1966 and in 1968 produced significant discoveries of reduced uranium ore by Humble Oil & Refining Company and others. Substantial reserves have been established in the area. High-grade carnotite ore was discovered in 1951 near Pumpkin Buttes in the central part of the basin (Fig. 1). Other mineralized areas were soon established from Pumpkin Buttes south to Monument Hill and Box Creek. Total production from these shallow oxidized deposits in the lower Eocene Wasatch formation was small. The AEC reports total production of 520,000 tons of ore averaging 0.19% U3O8. The authors are indebted to many people within Humble Oil & Refining Company and Esso Production Research Company for their assistance and guidance. SUMMARY AND CONCLUSIONS The Highland ore deposit, discovered in 1968, is a large uranium occurrence located in the southern part of the Powder River Basin. Uranium mineralization consists of sooty, black uraninite and coffinite coating sand grains and is concentrated along the margins of Tertiary fluvial sandstones. Uranium was transported by oxidizing solutions roving through the buried sandstones and spreading into less permeable channel-edge sandstones to form typical rolls and tabular deposits. Unaltered sandstones are light gray to gray-buff where the sandstones have been oxidized, the colors are various shades of red, yellow, and yellowish brown. An Oligocene tuffaceous source for the uranium is proposed; however, leaching of the arkosic and tuffaceous host sediments may also have provided a source.

Jan 1, 1971

By William C. York-Feirn, Jeffrey H. Kravitz, David Stalfort

"Mining is an inherently risky business. Over the years, major mine disasters have resulted in the deaths and injuries of thousands of miners in the United States. These disasters also resulted in innovations in approaches to mine design, operations and the training of miners and mine rescue teams. The U.S. Congress responded to these disasters with new laws designed to create mandatory safety and health standards as a means to eliminate fatal accidents; to reduce the frequency and severity of nonfatal accidents; to minimize health hazards and to promote improved safety and health conditions in the nation’s mines.Following a mine emergency preparedness and response holistic gap analysis in 2012, the U.S. Mine Safety and Health Administration (MSHA) identified the need for the development of risk and readiness assessment models for MSHA and the mining industry. MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the mining industry for use at operational levels. In 2012, MSHA hired ABS Group, a recognized industry leader in safety risk management and a wholly owned subsidiary of the American Bureau of Shipping, to develop self-assessment models to help meet this objective.In September 2012, MSHA chartered a project to supply the coal mining industry with a pro-active toolset for mine operators to:1. Self-assess the risks associated with underground coal mining operations in order to prevent major mine emergencies.2. Assess the preparedness of mine operators to respond to an emergency.3. Measure the readiness of mine rescue teams and responsible persons to execute emergency plans.MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the coal mining industry for use at operational levels."

Jan 10, 2018

By Emily Adelsohn, Robert Winn, Anthony Iannacchione

"Over 600 longwall panels have been mined in Pennsylvania in the last 50 years. Of those 600 panels, 25 panels undermined interstate highways. Despite this quantity of panels, much is still unknown regarding the detailed effects of undermining highways. The Gateway Mine, the Emerald Mine, and the Cumberland Mine undermined I-79 with 17 panels between 1982–1989 and 2003–2008, respectively; mine Eighty-Four undermined I-70 with 4 panels between 1987–2000.Through the examination of the panels that undermined I-70 and I-79, it is possible to determine which factors have most impacted the highway alignments. In some locations, the highway intersects with panels at angles ranging from 45 to 80 degrees, and at others, it runs between two panels, which simulates the effect of gateroads on the subsidence. The panels width to overburden ratio varies between 0.64 and 1.7, meaning that the interstates were influenced by both subcritical and supercritical subsidence basins. The face advance rates and overburden depths also vary between the panels.Unfortunately, specific information detailing highway impacts associated with unique characteristics of the subsidence basins are limited. However, using the profile function model and influence function model within the Surface Deformation Prediction System (SDPS), the effects of overburden, panel size, and orientation of the road to highway can be indirectly assessed by profile and influence models of subsidence basin formation.INTRODUCTIONCoal mining has been an integral part of Pennsylvania’s history. Room-and-pillar mines have been active since the late-1700s when coal was extracted from outcrops. By 1830, the city of Pittsburgh alone consumed more than 400 tons of bituminous coal each day for domestic and industrial use (PADEP, 2019). In the late 1960s, the face of mining in Pennsylvania changed with the development of full extraction longwall mines. Since that development, over 600 longwall panels have been mined in the Pittsburgh Coalbed in Pennsylvania alone (PADEP, 2019).As longwall mining and other forms of full extraction mining have increased in popularity, the amount of planned subsidence impacting the surface has also increased. The stresses and strains induced by longwall subsidence can cause damage to the surface as well any structures, water supplies, or water bodies that lie above the panel. Since the behavior of soils and structures vary, one way to study the surface effects of longwall mining is to analyze the impact on flat, rigid, pavement surfaces. Examining factors that vary the impact of subsidence with respect to highway alignment can demonstrate the favorable orientation of an alignment to avoid or mitigate damage and critical impact zones in a subsidence basin."

Jan 1, 2019

By David B. Costain

Three dimensional surface approximations are important means of evaluating physical and environmental factors that affect surface coal mining and reclamation. Computer approximated surfaces are projected as an array of square grid cells where individual cells define each parameter value respective to locations on the grid. Grid surfaces or grid cells within a surface can be compared or modified through application of standard mathematical functions. Surface approximations can be used to define the quantity and quality of marketable coal and to evaluate thickness and quality of overburden. Surface approximations also can be used to evaluate overburden swell factors wherein changes in post-mine topographic relief are related to expansion of unconsolidated materials in the backfill. Application of computer approximated surface to analysis of approximate original contour (AOC) standards allows an assessment of the quantity and geographical displacement of overburden and the distribution and numerical level of slope.

Jan 1, 1984

By D. Pappas

Over the past decade, the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry's injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked and injury rate. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992-2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent. Mining Engineering, 2011, Vol. 63, No. 11, pp. 73-79. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By A. J. Benham, H. Kessler

In the UK a high proportion of land-won sand and gravel is extracted from sub-alluvial gravels and river terrace gravels located within river valleys. However, extraction from deposits of this type is increasingly proving to be less acceptable. Quarries within river valleys often have a high visual impact and the cumulative impact of these operations in close proximity to each other can be high (figure 1). River valley operations are almost always restored to open water. Whilst these may be attractive for nature conservation and provide leisure activities, they can also have a serious impact on the natural hydrology of the flood plain. Wet restoration of quarries located close to airports or airfields can also lead to concerns regarding increased risk of bird strike on aircraft. The Civil Aviation Authority recently suggested that an exclusion zone of 13 km be applied around all airports and airfields to reduce the potential for bird strikes on aircraft. This action is likely to have a serious impact on the availability of potential sand and gravel extraction sites in river valleys.

Jan 1, 2005

By Stefan Medel

As a pioneer Herrenknecht started in 2018 to automate the production of tunnel lining segments. Since then, many automation processes became state of the art. Robots cleaning and oiling the moulds, hydraulic units opening and closing them fully independently. Artificial Intelligence (AI) controls the works and ensures the quality requirements. Data management has become a massive tool from a simple data collector towards a control and optimization tool. Sensors controlling concrete maturity and supporting the precast team to optimize the concrete mix. These state of the art and new innovations will be presented in this paper.

Jun 23, 2024

By P. Semberg, B. Bjorkman, C. Andersson

"In this study, the interaction between magnetite and the additive olivine was studied after oxidation as well as after isothermal reduction at temperatures in the 500º-1,300º C range. In the olivine sample, the forsteritic olivine particles react partly during the oxidation pretreatment to form magnesioferrite and vitreous silica along the particle corona. This breakdown of the olivine particles during oxidation liberates magnesium from the particles, which do not react until temperatures of above 1,150° C in reducing atmosphere. When the hematite in the sample is reduced, and when the temperature is high enough to allow solid-state diffusion at ~800º C, the magnesium of the magnesioferrite redistributes, so that the magnesium concentration approaches the same level throughout the iron oxide structure. For magnetite, this did not occur until 800° C. At 1,000° C, this magnesium reacts further with the silica in the glassy slag phase, which crystallizes into fayalitic olivine. At this temperature, the magnesium has diffused over distances of more than 600 µm from large olivine particles after 2 hrs reduction. From this point, the primary slag phase in the pellet, until melting, is solid fayalite. Upon reduction to metal, the metallization front concentrates the MgO in the remaining wustite, which can lead to MgO levels of up to 10 mole% locally. The melting point of the fayalite is raised from 1,145º C to a melting range of 1,238-1,264º C due to the MgO increase, as estimated based on phase diagrams, which were adapted to the pellets tested. Much of the olivine that remained unaltered in the oxidation process will be encapsulated by iron before the particles begin to dissolve in reducing conditions and, therefore, plays no role in the reduction before final melting of the particles occurs.IntroductionEnvironmental concerns have placed increasing pressure on the CO2-intensive iron and steel industries to further optimize operation toward higher productivity and more efficient use of reducing agents. At the same time, high demand for iron ore has caused new iron ores with lower grades and more complex chemistries to be taken into production. In Scandinavia, the main iron-bearing material is magnetite-based pellets with olivine, which allow operation with very low slag volumes and, hence, lower fuel rate ( Slagnes and Sundqvist Ökvist, 2008; Hallin et al., 1994). Both the MgO and SiO2 of the olivine, as well as the elements of the gangue of the ore, i.e., Si, Mg, Ca, Al and alkali, interact with the iron oxides to give the finished pellet product its final properties in the blast furnace. Tailoring the additive mix to be used for a certain iron ore for optimal product properties, therefore, requires detailed knowledge of the mechanisms by which these elements dissolve and react in the pellet."

Jan 1, 2015

By S. K. Kawatra

In most operating coal-cleaning plants, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. Reducing the pyrite recovery first requires that the primary recovery mechanism should be Identified, as different measures are required for reducing entrainment, locked-particle flotation, or true hydrophobic flotation. In this paper, evidence is presented which suggests that hydrophobic flotation is not an important mechanism for recovery of liberated pyrite from freshly-ground coal when the collector is a neutral oil, and that the bulk of the floated pyrite occurs either as a result of simple entrainment or by mechanical locking with floatable coal particles. Column flotation results are also presented which show that significant sulfur reductions can be achieved by reducing levels of entrainment.

Jan 1, 1992

By S. Odell

The Bureau of Land Management (BLM) has constructed two biochemical reactor systems (BCRs) to treat mining influenced water from the Forest Queen Mine near Silverton, CO. The bioreactors coupled with a natural wetland provide treatment to the Forest Queen Mine drainage. The central objective of this paper is to review the performance of the bioreactors and wetland treatment system. The bioreactors have been in operation for nine years and along with the natural wetland are still removing a high percentage of the influent metals.

Jan 1, 2010

By BERND SCHÖNHERR, JÖRG DEHNERT, PETER WINDISCH, JENS STOPP

The Quick-Erect Stopping System (QESS) offers a new way of reducing the radon exposure of miners in Germany, especially during remediation work in old mines. The QESS is a lightweight, modular and reusable construction kit of interlocking telescopic aluminum tubes, radon-proof foil and expanding foam. It is designed to seal off radon-rich parts of galleries within minutes. Originally, the QESS was developed to protect miners against radon exposure. Then, the QESS found the attention of several mine rescue teams at a German mining conference. Some mine rescue drills by The Student Mine Rescue of the Technical University Bergakademie Freiberg, Wismut Mine Rescue and Front Range Mine Rescue helped to improve the system and highlighted its potential for mine rescue operations. Now, the QESS is well-suited for small-scale mining. The QESS can be used to both protect miners from radon exposure and to support mine rescue operations. Moreover, the QESS was also successfully used in ventilation experiments.

By Derek J. Barratt

The existence of a critical size buildup in an autogenous or SAG mill can be predicted from proper examination of drill core and ore samples. Methods of dealing with such critical size in a primary mill are reviewed in the context of ore properties, whether or not pilot plant-scale testwork has been conducted, and also with respect to the design of new plants or the retrofitting of existing operations. The implications of not planning for pebble crushing in situations where it is appropriate are discussed.

Jan 1, 1992

By John W. Stevenson

At the No. 4 Mine of Jim Walter Resources in Tuscaloosa County in the North Central part of the State of Alabama, the Mary Lee and Blue Creek coal beds lay 2000 feet below the surface. The quantity of methane gas stored within the coal bed reservoir at this depth and released during development mining necessitates that each coal producing section be ventilated using large air quantities approaching 100,000 cfm. In order to meet coal contractural commitments in the early stages of mine development by installing the necessary number of continuous mining machine units and to develop the mine to projected air shaft sites, high pressure, large volume mine ventilating fans were required. This presentation discusses the installation start-up and changeover procedures when two size GAF 31.5-28-1 TLT-Babcock 3500 Horsepower fans with adjustable pitch in flight blades were put on line while phasing out two Jeffrey Mining Machine Company 8HUA 117 Fans. A graph will be presented to depict the most economic diameter shaft size under 2000 feet of cover with different air quantity requirements.

Jan 1, 1982