Search Documents

By S. S. Klima, J. A. Organiscak

Researchers at the National Institute for Occupational Safety and Health (NIOSH) performed laboratory testing to examine and improve airborne dust capture and methane removal performance of flooded-bed scrubbers on continuous mining machines using a blowing face ventilation configuration to reduce respirable dust exposure to shuttle car operators. Several testing conditions were examined to minimize shuttle car operator dust exposure without adversely affecting continuous miner performance and production. Curtain-to-face setback distance of 9.1 m versus 15.2 m (30 ft versus 50 ft), face ventilation airflow of 226.5 m3/min versus 339.8 m3/min (8,000 ft3/min versus 12,000 ft3/min), and the use of side-body-mounted blocking sprays (on versus off) were the three primary parameters compared. Scrubber airflow was set and maintained at 198.2 m3/min (7,000 ft3/min) throughout testing. An examination of slab cuts versus box cuts and the location of the shuttle car (present behind the continuous miner versus not present in the entry) was also performed to demonstrate the effects of these constantly changing scenarios on scrubber performance. Results show that the best blowing face ventilation setup for minimizing shuttle car operator dust exposure for the tested parameters uses a 15.2-m (50-ft) curtain-to-face setback with 339.8 m3/min (12,000 ft3/min) face ventilation while operating the side-body-mounted blocking sprays. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in U.S. underground coal mining operations, potentially leading to coal workers’ pneumoconiosis (black lung). The U.S. Mine Safety and Health Administration (MSHA) requires that respirable dust exposure to coal mine workers does not exceed a 1.5 mg/m3 average over the actual working shift (79 Fed. Reg. 24814 (2014)). Although using a blowing face ventilation configuration on continuous miner (CM) sections is beneficial for removing methane emissions from the mining face, it can be detrimental for dust control for shuttle car (or ram car) operators and any other workers on the return ventilation side of the CM when compared to exhausting ventilation. Even with machine-mounted scrubbers on CMs, shuttle car operators still have some of the higher dust exposures with blowing face ventilation systems (NIOSH 2011, Beck et al. 2015). Although scrubber discharge air is not completely clean, dust being blown around the scrubber inlet and therefore not being captured by the scrubber can further increase these dust exposures (Goodman 2000). Dust control problems are also caused by inadequate face ventilation quantities causing scrubber face airflow recirculation issues (Schultz et al. 2010). In order to minimize respirable dust exposures on blowing face ventilation sections, ventilation, water spray, and scrubber parameters were experimentally examined to improve operating ranges for both dust and gas control. Several blowing face ventilation factors were examined with respect to CM spray systems and scrubber operation. Curtain-to-face setback distance and side-body-mounted blocking sprays were previously examined in the laboratory for dust control on a full-scale CM model using a scrubber on a blowing face ventilation system (Goodman 2000). The blocking sprays produced larger dust reductions at the CM’s rear corners and return for a 6.1-m (20-ft) curtain setback distance as compared to a 12.2-m (40-ft) curtain setback distance with equal face and scrubber airflows of 169.9 m3/min (6,000 ft3/min). Because face ventilation airflow quantities, shuttle car operator locations, and tracer gas concentration gradients were not previously examined during these experiments, additional research was required to determine improved operating parameters for blowing face ventilation systems.

Jan 1, 2019

By J. D. Miller

The recent non-equilibrium electro-phoretic mobility measurements by laser-Doppler electrophoresis coupled with the stability and prevalence of collector colloids in soluble salt flotation systems suggest that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by hetero-coagulation. Previously reported flotation results confirm this surface charge/collector colloid adsorption model. However, the nature of the inter-particle forces responsible for hetero-coagulation of such oppositely charged particles at high ionic strengths remains to be determined. In this regard, atomic force microscopy was used for inter-particle force measurements at high ionic strengths. Model systems such as polystyrene/quartz and silica/sapphire were studied to measure the particle interaction forces prevalent at high ionic strengths. Results from this study indicate that while repulsive hydration forces exist between similarly charged hydrophilic particles, attractive forces exist between oppositely charged hydrophilic particles in high ionic strength solutions. The repulsive forces between similarly charged hydrophilic surfaces at high ionic strengths (2-4 M) are described by a double exponential function with decay lengths of 0.17 and 1.4 nm depending upon the surfaces involved. On the other hand, attractive forces were observed between oppositely charged hydrophilic surfaces at high ionic strengths (2-4M) and were described by a single exponential function with decay lengths of up to 9 nm depending upon the surfaces involved.

Jan 1, 1996

Laboratory tests were conducted in a full-scale continuous miner test gallery to evaluate resulting dust levels for changes in face airflow, spray water quantity and pressure, and mining height. The minimum and maximum values tested for each parameter were as follows: airflows between 1.42 and 6.14 m3/sec, water flows between 56.8 and 132.5 lpm, nozzles pressures between 413 and 1379 kPa, and mining heights between 1.52 and 2.74 m. Each of these parameters were evaluated for four common spray system designs. Respirable dust samples were collected in the operator's cab on the miner and in the immediate return. Second-order polynomial models were used to represent expected dust levels and multiple stepwise regression was used to identify significant control parameters for inclusion in the models. Separate models were developed for dust levels at the operator and return locations and for each individual spray system. Interaction between control parameters and curvature effects were found in most models. The analysis indicated that at the operator location, airflow and mining height had the most significant impact on respirable dust levels. In the return, airflow and water pressure were typically the most significant parameters. The models developed for each spray system design can be used by mine operators to guide application of control parameters for a variety of operating conditions and mining heights.

Jan 1, 1994

By Jorge Amaya, Nelson Morales Varela, Francisco Saavedra, Gonzalo Nelis, René Gómez

Precedence constraints are broadly used in mathematical models and algorithms for mine planning to model, for example, slope angles in open pit operations or connectivity in underground mines. Unfortunately, these constraints do not capture relevant geometrical aspects for the design of the mine like minimum bottom space of pits or smoothness of the economic envelope in block caves. In this work, we present different approaches that utilize precedence constraints generating economic envelops that are more suitable for design purposes. The numerical experiences show that the proposed techniques produce high value envelops with better geometrical properties and that the methods proposed can be computed efficiently.

Jun 25, 2023

By M. S. Celik

Beneficiation of boron minerals by flotation with well defined systems has been very little investigated in the literature. The difficulty arises from the fact that boron minerals cover a spectrum of solubilities. Colemanite, a calcium containing relatively insoluble boron mineral, and borax, a highly soluble boron mineral have been used to exemplify the flotation of boron minerals. The floatability of both minerals using sodium dodecylsulfonate and dodecylamine hydrochloride exhibits considerable differences in their response to flotation. This has been ascribed to variations in the solubilities 0f boron minerals and the presence of the cations in the lattice structure. Flotation tests along with zeta potential measurements are used to elucidate the mechanisms involved in the flotation of boron minerals.

Jan 1, 1992

By L. P. Meade

The need to feed an established talc mill from a crude are source located closer to the mill prompted the drilling in 1986 of a previously mapped talc-carbonate deposit. This talc-bearing rock had never been considered as a potential source of crude talc are because of the high carbonate content and other deleterious minerals that were observed in outcrops. Selective mining, in-pit grade control and creative processing has allowed this deposit to be developed into an orebody. By definition, an orebody has to be a source of positive cash flow. With industrial minerals, this is determined as much by market acceptance as by are tenor.

Jan 1, 1992

By Wilbur I. Duvall

INTRODUCTION This chapter outlines some general principles and procedures that a rock mechanics engineer can use to arrive at a logical design for the size, shape, and spacings of underground openings in various types of com¬petent rock formations. Rock formations can be clas¬sified into six major categories which are useful for design purposes, provided the necessary input data are available regarding the geology of the site, the physical properties of the rock, the in-situ stress field in the rock, and the general geometry of the underground openings. The US Bureau of Mines (USBM) developed a rock classification system based upon these concepts and found it to be useful for design purposes (Obert, et al., 1960; Obert and Duvall, 1967). This classification sys¬tem is given in Table 1; however, an extra column has been added to the original classification to indicate the appropriate design techniques for each rock class. In this classification system, two main classes of rock are considered: competent rock and incompetent rock. Competent Rock Competent rock is any rock which, because of its mechanical and geological characteristics, is capable of sustaining underground openings without the aid of any structural support except that provided by unmined rock in the form of pillars and side walls, etc. Roof bolts and small random props which support only local loose rock are not considered structural supports. Competent rock is further subdivided into three ad¬ditional categories-massive, laminated, and jointed¬ which are defined as follows: Massive Rock: Massive rock is a rock formation where the spacing between mechanical defects such as joints, partings, or faults is equal to or greater than the critical dimensions of openings, or where the strength of the bond across these mechanical defects is com¬parable to the rock strength. Laminated Rock: Laminated rock is a rock forma¬tion divided by approximately parallel planes of weak¬ness into lamina whose thicknesses are small compared to critical dimensions of openings and where the bond between the lamina is weak compared to the rock strength. Elastic Rock-This is rock whose physical proper¬ties will permit the use of elastic theory to predict strains and displacements from applied stresses. Inelastic Rock-This is rock whose physical proper¬ties are such that strains and displacements are a strong function of time as well as applied stress. Incompetent Rock Incompetent rock is any rock which, because of its mechanical and geologic characteristics, is not capable of sustaining underground openings without the aid of additional structural support in the form of linings, steel sets, or systems of props. This classification system for rock depends not only on the mechanical and geologic characteristics of the rock but on the size of openings and their depth be¬low the surface. For example, many competent rocks at shallow depths for small stress fields could become inelastic rock at greater depths and larger stress fields, or competent massive rock for small openings could be¬come laminated or jointed rock for larger openings. Thus, to classify rock for design purposes requires a knowledge of the geologic properties of the rock mass, the physical properties of the rock, the general size of the openings to be mined, and the average range of the in-situ stress field to be encountered. To design underground openings and structures in rock, it is necessary to use criteria of failure for rock under various stress conditions, and to use safety factors to allow for differences between laboratory and in-situ strength properties of rock and to account for errors in¬troduced by the various assumptions made in the design process. Criteria of failure based on maximum stresses have been found to give reliable results in practice. Thus, it is assumed that rock will fail in tension when the tensile stress exceeds the tensile strength of the rock as determined by a standard modulus of rupture test on samples of rock core. If the tensile stresses in rock are small, then it is assumed that the rock will fail at a value of compressive stress equal to the compressive strength of the rock as determined by standard uniaxial compres¬sive strength tests on samples of rock core. These fail¬ure criteria, when used with appropriate safety factors, can be expressed as:

Jan 1, 1982

By William J. Miles

For compliance with the Hazard Communication Standard and other federal and state regulations, numerous minerals, chemicals and products need to be evaluated for crystalline silica content at a threshold of 0.1 %. The polymorphs of crystalline silica that can occur in chemical and mineral products are quartz, cristobalite and tridymite. Other natural, industrial and synthetic amorphous silicas and hydrates must be distinguished from these polymorphs to prevent over-regulation in the workplace and environment. A number of industrial silica products are composed of glasses, expanded perlite, diatomite, slags, and precipitated and fumed silica products. Amorphous silica hydrates used for industrial products, include opal (hydrated silica of biogenic or inorganic origin), perlite, pumice and tuffs. In addition, crystalline and amorphous silicate minerals and chemicals, abundant in nature and industrial products, must be distinguished from the polymorphs of crystalline silica.

Jan 1, 1997

By William F. Stowasser

The organization and operations of the information gathering system, and examples of the products prepared for the commodity phosphate rock by the Division of Nonmetallic Minerals, U.S. Bureau of Mines, are used to describe the Bureau's commodity program. Selected examples from publications about phosphate rock are used to illustrate the program. The Commodity Divisions reporting to the Office of the Assistant Director-¬Metals, Minerals and Materials, have the responsibility in the Bureau of Mines to maintain commodity records, understand the present supply and demand status of the commodity, and forecast future supply, demand, and problems. Within the Divisions, commodity specialists have the broad charter of acquiring as much information about a commodity as is necessary to characterize its history, current status, and future. This information and understanding are the base for the development of mineral policies. To accomplish these objectives, the commodity specialists acquire data and information about each commodity and produce a number of standard publications each year. In addition, as circumstances dictate, each specialist will prepare or participate in the preparation of special documents for specific purposes or problems associated with his commodity. In the preparation of reports and publi¬cations, he may communicate with industrial organizations and other Government agencies.

Jan 1, 1975

By P. A. Schmitz

The characteristics of gold leaching from carbonaceous matter by sodium cyanide, and sorption of gold cyanide to carbonaceous matter in autoclaved and non -autoclaved gold ore from Barrick Goldstrike Mines Inc. (BGMI), Nevada, was investigated. Much greater gold cyanide complex sorption was observed for the carbonaceous matter in high preg-robbing ores relative to the low preg-robbing ores. This observation corroborates previous reports that have attributed observed preg-robbing behavior to the carbon in the ore. Gold cyanide complex sorption was found to be reversible for carbonaceous matter from low preg-robbing ore, but was irreversible for carbonaceous matter from high preg-robbing ores. Autoclaving the ore appeared to enhance the sorptive behavior of the carbonaceous matter from both high and low preg-robbing ores.

Jan 1, 1999

By Keshavan Nair

In connection with Project Payette, which is concerned with the detection of underground nuclear explosions, it was necessary to determine the technical feasibility of constructing and maintaining a large (approximately 315 feet in diameter) unsupported underground cavity at a depth of approximately 2700 feet in the Tatum Salt Dome in Mississippi. The dimensions and the location of the cavity in the salt dome were governed by criteria laid down by the Atomic Energy Commission. Within the framework of the specified criteria, cavities of various shapes and dimensions could be utilized. One aspect of the feasibility study was to investigate the structural stability of various cavity shapes and to recommend a preferred shape. This paper summarizes the studies that were conducted to evaluate the structural stability of various proposed cavities.(l)

Jan 1, 1968

By R. P. Fischer

Traditionally, molybdenum and vanadium have been used chiefly as alloy metals in steel. They impart similar characteristics to most steels, and to some extent one can be substituted for the other. In the United States during the 1950's the production of steel increased about 5 percent, and the reported consumption of both of these alloy metals in steel increased some 40 percent. In Europe during the 1950's the production of steel in¬creased nearly 100 percent. Data on the actual consumption of these alloy metals in European steels are not available, but production and trade records show that the European supplies of molybdenum increased about 150 percent and those of vanadium about 350 percent during the 1950's. If most of the molybdenum supplies in Europe are being added to steel, as seems likely, then the European steel industry has nearly caught up with the United State in the rate of consumption of molybdenum in steel. The vanadium supplies, on the other hand, are puzzling--unless Europe is adding mach more vanadium to steel than is done in the United States, it seems reasonable to assume that other uses are consuming moderately large quantities of this metal or that appreciable amounts of it are being transshipped from Europe. To the extent that a changing volume of supply signifies a changing pattern of use, the increased demand for molybdenum and vanadium in Europe should be of interest to domestic producers and consumers of these metals.

Jan 1, 1964

By D. K. Steele

The U.S. Bureau of Mines has investigated the recovery of metals from copper industry wastes by sulfuric acid leaching in a semi-continuous, bench-scale system to solubilize arsenic, copper, and molybdenum. Leach residues contained approximately 40 wt pct PbSO4, suitable for processing at a lead smelter. Arsenic and molybdenum removal from leach solution was examined using solvent extraction with tri-n-butyl-phosphate (TBP), and copper was subsequently recovered by cementation. Bleed electrolyte from a copper refinery was determined to be a viable source of acid for the initial leach stage.

Jan 1, 1991

By Ching-Yi Tsai

The effect of various constituents on the pyrolysis and combustion of a pulverized coal in an entrained-flow reactor has been inves¬tigated. Predicted time-temperature histories of the coal' particles and experimental weight loss data indicate a strong coupling of heat and mass transfer to the pyrolysis and combustion rates. A higher combustion rate following ignition was observed as particle size was increased to 112 µm. This is related to a higher particle temperature after ignition for the larger particles. Although the heating rate prior to ignition decreases with increasing particle size, higher slip velocities and surrounding gas temperatures for the larger particles promote early ignition. The presence of liptinite in the coal increases the weight loss rate before and immediately after ignition. Similar behavior was observed for pyrolysis. Fractions of a HVA bituminous coal which were rich in mineral matter or semi-fusinite were found to have a higher heterogeneous char combustion rate than vitrinite rich samples.

Jan 1, 1984

By D. K. Dysinger

The U.S. Bureau of Mines investigated leaching of chalcopyrite with sulfuric acid-oxygen under conditions anticipated during in situ leaching. A central composite experimental design was chosen to study oxygen pressures of 150, 300, and 450 psi, leach temperatures of 35?, 65°, and 95° C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0, and 1.5, leach times of 8, 16, and 24 hours, initial acid strengths of 0.6, 1.2, and 1.8 g H2SO4/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. The leaching kinetics were consistent with the shrinking core model. A quadratic response surface model was used to determine linear and interaction effects of the design factors on rate constants from Arrhenius correlations.

Jan 1, 1993

By Alan Boughey

The world's largest grinding mill operates at the Cadia Hill Mine in Australia. Svedala Industries supplied the 12.2-m- (40-ft-) diam, 20-MW Cadia gearless, semiautogenous grinding mill (SAG). This was a leap of more than 40% above the largest operating SAG mill. This article reviews the significant items involved in the development, design, manufacture, installation and operation of this mill. Description of the Cadia project The Cadia Hill Mine is located 25 km (15 miles) southwest of Orange, in the Central Tablelands of New South Wales, Australia. The mining lease covers about 3,100 hm2 (7,660 acres) of the Cadia Valley. The Cadia deposit is a large, homogeneous, low-grade, porphyry-type, gold-copper resource. Current reserves stand at 202 Mt (222 million st), grading 0.73 g/t (0.02 oz/st) gold and 0.17% copper. They contain 146.2 t (4.7 million oz) of gold and 347 Kt (382,500 st) of copper. The operation consists of openpit mining and ore processing to produce gold bullion and a gold/copper concentrate. The operation processes 17 Mt/a (19 millon stpy) of ore to produce 91 kt/a (100,300 stpy) of concentrate and 9.1 t/a (293,000 oz/year) of gold. The plant operates two 12-hour shifts a day and had a targeted availability of 94%. The plant facilities include a copper concentrator, o water supply system, an openpit mine, tailings pipeline and dam, and a concentrate pipeline and dewatering facility located in Blayney, about 35 km (22 miles) from the concentrator. Significant features of the process plant include o primary crusher and stockpile, a reclaim conveyor system feeding, the Cadia SAG mill (Figs. 1 and 2) and two 6.7-m- (22-ft-) diam ball mills (Fig. 3). A portion of the gold is extracted in a gravity circuit. The balance is extracted with the copper in the flotation section of the plant. Concentrate is thickened and piped about 35 km (22 miles) to the filter plant and rail loadout facility located in Blayney. Tailings are pumped to a tailings dam and process water is reclaimed from the tailings dam. The water system is designed to control and capture available runoff from local creeks, and to store these waters in dams and weirs. In addition, a major portion of the water for the process plant is treated effluent from the city of Orange and a smaller portion from Blayney Mill selection. The low-grade ore posed a dilemma for Cadia. To achieve a satisfactory economic operation, large-scale processing was required. The selection of the mills, equal to the largest designed and operated at the time, gave a plant configuration consisting of two 11.1- x 5.8-m (36- x 19-ft) SAG mills and three 6.1- x 9.1-m (20 x 30-ft) ball mills. This configuration did not provide the most satisfactory economic model for the project. A review of the single line configuration indicated that a significant reduction in the overall capital cost of the plant could be achieved by increasing the size of the mills and reducing the quantity. Increasing the size of the mills,

Jan 1, 2001

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"Duluth & Iron Range Railroad. The Duluth & Iron Range Railroad was built from Two Harbors to the Vermilion range at Tower, a distance of 67.6 miles, in 1884, and extended to Ely, twenty-one miles east of Tower, in 1888. It was built into Duluth in 1886, and branches were extended from its main line to the Mesabi mines in 1892 and 1893. The original grades on this road are very steep, going north, and in the thirteen miles from Two Harbors to Highland there is a rise of 1,150 feet. A new line between these points has been built with an increase of three miles in distance and with maximum grades of 1 per cent. Duluth, Missabe & Northern Railway. The Duluth, Mis¬sabe & Northern Railway was constructed from Stony Brook to Mountain Iron, a distance of 48.62 miles, in 1892. The Biwabik branch from Iron Junction to Biwabik, a distance of 15.54 miles, was constructed in 1892. The Superior branch from Wolf to Hibbing, a distance of 16.06 miles, was co11structed in 1893. The Alborn branch from Coleraine Junction to Coleraine, a distance of 53 miles, was constructed in 1906. The total main line mileage is 242 miles, of which 82 miles from Duluth to Hibbing is double tracked"

Jan 1, 1920

The properties of interfacial water at hydrophilic surfaces are of great importance in many technological areas including flotation, solid-liquid separation, dispersion and emulsions, flocculation, adsorption, corrosion, and soil contamination. This paper examines the use of FTIR/internal reflection spectroscopy (FTIR/IRS) to study the spectral characteristics of interfacial water at silica surfaces. FTIR spectra were characterized by consideration of the OH stretching region (3000-3800 cm-1) associated with the vibrational spectra of interfacial water. The broad peak in this region was deconvoluted in order to isolate overlapping spectral features that describe the nature of hydrogen bonding in interfacial water. Three distinct bands were found; -3600 cm-1 (free OH), -3400 cm-1 (incomplete tetrahedral coordination), and -3240 cm-1 (complete tetrahedral coordination) and the variation of their intensities with pH was found to be significant. This spectral information helps to explain orientation and bond ordering of interfacial water molecules at hydrophilic surfaces.

Jan 1, 1998

By H. J. Chen

In recent years, it has been recognized that the high horizontal stress is an important factor that contributes to a cutter roof. When the immediate roof is thinly bedded, the presence of a high horizontal stress may first cause failure on the bedding planes or weak planes, and then a cutter roof develops as the individual stratum crushes and buckles progressively layer by layer. In this study, the stress distributions in the bedding planes of the immediate roof are analyzed for an entry-pillar system in the multiple longwall panels by using the finite element method. Then the roof failure is analyzed based on the rock failure criterion and the stress distributions.

Jan 1, 1998

By Allan M. Hale

Taconite tailings reclamation, especially the stabilization of tailings ponds, .dams, and slopes, can be effectively accomplished through the use of appropriate vegetation. Utilizing vegetation provides both aesthetic and ecological enhancement of a site while at the same time protecting tailings structures against wind and water erosion. Generally, the methods and techniques for establishing vegetation are well known; however, there are many site-specific factors that can alter a particular reclamation approach. Those factors include slope gradient, tailings material size, solar exposure, and physical and chemical properties of tailings. In addition to the site-specific factors, variations in climate, geography, and physiography of a region can have a pervasive influence on the success or failure of a revegetation program. Both the site-specific and regional factors control reclamation planning in such areas as plant variety selection, methods and times of plants establishment, maintenance techniques, and subsequent monitoring methods. As a result of this multifactor relationship, it is important to establish a data base that identifies both the site-specific and location conditions in order to tailor the reclamation plan to the specific area. When an appropriate data base has been collected, detailing the various site-specific and regional factors that will influence a revegetation program (in the absence of previous testing), it is very beneficial to apply experimental techniques to develop the reclamation plan for a specific site. The reclamation plan for a specific site may include several techniques adapted for the differences found within the specific site as the result of topographic or other influences. Considering this, the Reserve Mining Company and Dames & Moore undertook to develop a successful reclamation plan based on a detailed test plot program conducted at the Mile Post 7 location.

Jan 1, 1980