Search Documents

By R. R. Klimpel

This paper describes four new families of flotation products which are currently being introduced at the industrial level. A brief summary of the chemical basis behind each product family will be given. This is then followed by a selection of flotation examples which illustrate the more important use characteristics that have been observed to date. It is becoming more apparent with further testing that these four new product families can offer both technical and economic advantages to the industrial flotation process operator.

Jan 1, 1992

By J. Noll, D. Yantek, B. Kendall, J. A. Organiscak

"A self-tramming remotely controlled mobile Dry Scrubber (DS) was developed by J. H. Fletcher and Co. under a contract with the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research (NIOSH OMSHR) to reduce exposure of miners to airborne dust. NIOSH OMSHR laboratory testing showed that the DS averaged greater than 95% dust removal efficiency with the disposable filters and averaged 88% and 90%, respectively, for the optional washable filters in their pre-washed and post-washed test conditions. Although the washable filters could be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-minute washing period. The DS’s velocity pressure regulated variable frequency drive (VFD) fan maintained a relatively consistent airflow near the targeted 1.43 and 4.25 m3/s (3000 and 9000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60 Hz fan motor frequency or horsepower rating at 2610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the DS also showed that the outlet side of the scrubber was noisier and the loaded filters increased sound levels as compared to clean filters at the same airflow quantities. With loaded filters the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level (PEL) of 90 dB(A) at or below this airflow quantity (1). The DS’s washable filters were not used during field testing because of their lower respirable dust removal efficiency and the airborne dust generated from filter washing. Field testing the DS with the disposable filters at two underground coal mine sections showed that it can clean a portion of the section return air and provide about a 50% dust reduction at the face area downstream of the continuous miner (CM) operation. INTRODUCTION Coal mine worker overexposure to coal and quartz dust continues to be a problem at underground coal mining operations in the U.S. The U.S. Mine Safety and Health Administration (MSHA) recently changed the standard for coal mine worker respirable dust exposure from 2.0 mg/m3 average during an eight-hour shift to 1.5 mg/m3 average over the actual working shift, effective as of August 1, 2016 (1). If more than 0.1 mg/m3 quartz mass is found in the coal mine worker dust sample, the applicable respirable dust standard is further reduced to the quotient of 10 divided by the percentage of the quartz in the sample (1). Over 90% of the mechanized mining units operating in U.S. underground coal mines are continuous mining machines (2). MSHA inspector dust samples from 2009 to 2012 showed that 3.7% of continuous miner operators exceeded the 2.0 mg/m3 dust standard, while 8.8% of these dust samples exceeded the new 1.5 mg/m3 dust standard and 9.7% of these samples exceeded the reduced quartz standard (3). Additionally, roof bolter dust samples at these mechanized mining units during this same period have exceeded the 2.0 mg/m3, 1.5 mg/m3, and reduced quartz levels at 1.1%, 3.7%, and 10.6%, respectively (3)."

Jan 1, 2016

By H. M. Ray

The discovery of the New Lead Belt in the mid-'50s began a search for mill design criteria that is continuously updated. The opportunity to design, construct, and operate four new mills in the span of 20 years provided fertile areas for new concepts. The central theme for design parameters encompassed simplicity, functional, and economic consideration. Ore characteristics for each plant remained relatively constant, providing stable criteria for grinding circuits. Bond index nominally 10-12. Flotation circuit parameters were based upon power application with 10-20% excess capacity built-in to protect recovery. Newer equipment exhibits greater power application efficiency lowering horsepower requirements per ton. Instrumentation was installed to stabilize circuits, protect equipment, and improve products. With ever increasing requirements of higher quality products, environmental considerations, and operating cost pressures, the upgrading of operating procedures is in a constant state of flux. Installation of more efficient equipment, chemical processing, or any other technique would be considered as feasible. Current practice is for St. Joe to design and engineer in-house its own plant design. The exception being detailing of structural steel. It is felt that familiarity with past design criteria serves as a valuable foundation to incorporate changes. Also, direct contact with operator provides specific data, and feedback for constructive criticism that is utilized for defining and correcting problems. The results are in reality an operator's plant with the benefit of advancing technology that meets the demands for improved products without sacrificing the economies of throughput or recovery.

Jan 1, 1977

By D. Malhotra

Most primary-molybdenite producers use a selective-flotation process in which molybdenite is floated from the ore while other sulfide and non-sulfide gangue minerals are depressed in the same step (Figure 1). The process was developed at the Climax mill. Reagents used in the rougher-flotation stage include vapor oil (collector), syntex (surfactant), pine oil (frother) and occasionally sodium cyanide and Nokes reagent (depressant). Rougher concentrate is upgraded by cleaner flotation to produce market-grade molybdenite concentrates. Reagents used in the cleaner flotation stage are Dowfroth 250, vapor oil, sodium cyanide and Nokes reagent. The development of the flotation reagent scheme at Climax and the role of the reagents have been well described by Born, et al, (1976) and Malhotra, et al, (1976, 1977a, 1977b, 1977c, 1980). The hydrocarbon collector, vapor oil, accounts for approximately 50 percent of the total molybdenite-flotation reagent cost. Because vapor oil sources are limited, and the cost of vapor oil has increased significantly over the last decade, several studies have been done to evaluate alternate oil-based collectors and/or blends of collectors which would produce similar metallurgical results at a reduced cost, or increase the overall molybdenite recovery at the same cost (Smit and Bhasin, 1983; Hahn, 1969; Smith and Bhappu, 1971). The approach taken in the present study was to evaluate alternate non-oil based collectors and collector systems that are less expensive than vapor oil.

Jan 1, 1985

By S. C. Suboleski

In a high risk venture such as mining where capital is committed and contracts are signed on the minimum of information, decisions are based primarily on production forecasts derived through consideration of such factors as management-labor relations, mining practice, variations in physical conditions and the equipment applied. Among these factors, the physical conditions offer the least opportunity for control and, due to the wide range of mining conditions that may be experienced, little effort has been made to develop objective methods for measuring their effects on mine out- put. The aim of this paper is to demonstrate a method for assessing these relationships that can be applied under a wide range of conditions both in new mines and in working sections where there is a need to determine the impact of proposed operational modifications. psing empirical data from active underground mines, a mathematical model was developed to derive a set of regression equations for predicting production as a function of mining conditions

Jan 1, 1980

By A. D. Trippel

The Cripple Creek Mining district is located in Teller County, Colorado, 30 km west of Colorado Springs and 9 km southwest of Pikes Peak (Fig. 1). Since its discovery in 1891, the district has produced almost 21 million tr oz of gold (Gott et al., 1967), most of which has been from high-grade vein deposits. Globe Hill is located in the northern part of the district (Fig. 2). Production from its summit has yielded over 100,000 tr oz of gold. Early production was concentrated along high-grade veins and fault structures, but emphasis was soon placed on the extensive, low-grade (0.0X oz/t), breccia-hosted mineralization. From 1977 to 1981 Newport Minerals, Inc., a subsidiary of Gold Resources, Inc., mined 680,000 t of low-grade gold ore from the Globe Hill pit (Fig. 3) and production is expected to resume in 1986. These strongly-altered and -oxidized breccias are amenable to bulk-mining methods, and thus similar deposits are currently being sought elsewhere in the district. Numerous publications and reports discuss the breccia-hosted mineralization at Globe Hill. They include Cross and Penrose (1895); Argall (1905, 1908); Lindgren and Ransome (1906); Keener (1962); Peters (1982); Thompson, Trippel, and Dwelley (1985); and Trippel (1985). This preprint is a summary of the recently-completed research documented by Trippel (1985).

Jan 1, 1986

By F. Calizaya

This study summarizes the ventilation requirements for the highly mechanized PT. Freeport Indonesia's underground mine operation in Irian Jaya, Indonesia. The deep ore zone (DOZ) is a coppergold deposit that is being developed underneath the current intermediate ore zone (IOZ) mine. One of the company's current plans is to prepare this mine for a steady ore flow of 25 kt/d (27,500 stpd) by 2003. This study includes the estimation of airflow requirements for various mining activities, the design of major intakes and returns, the determination of airway resistances and specifications of fan duties. It also includes the results of air pressure/quantity measurements in existing airways and the standards stated by the current Indonesian mining law.

Jan 1, 2000

By J. C. Haptonstall

Stoping methods at the Homestake Gold Mine through 1978 had been traditional overhand cut-and-fill, shrinkage or square set. High costs, low-productivity and safety concerns prompted the mine to search for and adopt a "bulk mining" technique as a primary stoping method. Blasthole stoping had been successful but it is very development intensive, and was not suitable for the mine's accelerated mining program. Vertical Crater Retreat stoping was selected, and today accounts for over 50% of ore production. Case histories representing both the successes and failures of VCR stoping in the mine are discussed.

Jan 1, 1986

By A. Mayton

The prolonged exposure of equipment operators to shock and whole-body vibration (WBY) is linked to cumulative back, neck, and abdominal disorders. In low-coal mines, space restrictions make seat suspensions difficult to use in isolating operators from shock and WBY. Researchers at NIOSH, Pittsburgh Research Laboratory, are responding to these issues by investigating viscoelastic foams. For the full-load case. an ergonomic seat with viscoelastic foams isolated the shuttle car operator from shock at 15Hz. Researchers used results from additional foam testing with an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Jan 1, 1998

By Vincent J. Murphy

INTRODUCTION Geophysical applications to engineering projects are usually considered for reconnaissance exploration, and for some preliminary design phases. Recent experience indicates a growing need and a greater number of requests for measurements during construction. This is particularly true where seismic velocity values are related to strength properties of rock. Typical project objectives during construction are: dike and tunnel realignments required by surprise conditions encountered during foundation preparation; checks on grouting effectiveness which require velocity measurements before and after grouting; and dynamic moduli measurements along the walls of tunnels and deep excavations. This paper considers one of the on-site seismic applications that is rather simple and straightforward, and yet has few references in the literature. The specific objective is the measurement of seismic velocities (both "P" waves and "S" waves) for determining the thicknesses and dynamic moduli values of loosened zones of tunnel wall rock. PRE-EXCAVATION SEISMIC METHODS The seismic methods suitable for engineering project studies are well known and especially suited for routine site reconnaissance; these are illustrated in Fig. 1. The seismic refraction profile with a

Jan 1, 1997

By M. Boucraut

After stating the advantages of the magnetic roasting technique as applied to iron ores, the authors report on technological research by I R S I D * in the field of magnetic roasting in fluid-bed furnaces This investigation was conducted first on an experimental two stage fluid-bed furnace which processed permanently 100-200 kg/h of ore, then on a three stage fluid-bed furnace with 1-2 t/h working capacity and at last on a 250 t/day pilot furnace The specific features of the IRSID process comprise - on the one hand, using special burners in the roasting reactor thereby ensuring a high production rate of the furnace - on the other hand, using a heat-exchanger where the preheating and cooling stages of fluidized ore are associated, so as to allow an efficient and simple cooling of both roasted ore and waste gases flowing out of the roasting reactor, thereby supplying heat to the crude ore and combustion air for the reactor burners Starting in 1965 the operation of the 250 t/day pilot plant at the Bazailles mine gave IRSID the opportunity of improving the conveying appliances and adapting them to the process, while perfectly confirming the metallurgical results obtained under ideal laboratory conditions

Jan 1, 1968

By B. Berhe, R. D. Lawrence, J. Hinzer

"The fortunes of mining companies and their implied value are tied to cycles - both economic and commodity – within which they operate. Hence the determination of appropriate future metal prices is one of the most critical factors faced by mineral valuators especially for advanced projects. Price, and hence revenue, is usually the most sensitive input to the valuation model. Empirical studies of past forecasts show that the success rate for commodity price forecasting is very poor. This paper explores various approaches and comments on their strengths and weaknesses. We conclude that careful evaluation of long-term metal prices is a key element and is hardly a luxury that can be left to simple averages or rules of thumb. INTRODUCTION Discounted Cash Flow (""DCF"") analysis, is well suited for the valuation of advanced mineral development assets, for which there are identified mineral resources and some form of economic assessment (Pre-Feasibility or Feasibility Study). The DCF method is also the most commonly used method for determining value for such assets. It provides a means of relating the magnitude of expected future cash flows from profits (or losses) to the magnitude of the initial cash flow (investment) needed for capital expenditures to purchase or to develop an asset for commercial production. The method proves useful in making investment decisions as it allows for the quantification of the Net Present Value (“NPV”), as well as the Internal Rate of Return (IRR) and Payback Period on initial investment capital. Valuation by its very nature is a forward-looking exercise. The DCF method attempts to estimate the NPV of expected future cash flows, by selecting factors that will likely affect future cash flow based on informed analysis. One of the most critical and sensitive factors is the determination of appropriate future commodity prices. “The variables that have the greatest impact on a DCF evaluation are the reserves, the metal prices, and the discount rate.”1 The determination of future commodity prices for valuation purpose or during M&A negotiations is a hotly contested issue. There are a number of analysts, institutions and specialized commercial data suppliers that provide both short and long-term commodities price forecasts. Also, the use of an aggregated mean for all available forecasts, or consensus forecasted prices for valuation purposes is not uncommon. The methods used in making forecasts for each forecaster may vary and in many cases may not be publically disclosed. Nonetheless, the aggregated mean of all forecasted commodity prices of reputed institutions is usually taken to “represent the market’s view of likely future commodity prices.”"

Jan 1, 2016

By Shawn Benner, David Blowes, Carol Ptacek

A full-scale reactive barrier was installed into an aquifer impacted by acid mine drainage in August 1995 at the Nickel Rim mine site near Sudbury, Ontario. The primary mechanism of water quality improvement is bacterially mediated sulfate reduction and metal sulfide precipitation. Dramatic changes in the groundwater chemistry are observed with up to 90% decline in Fe (from >18 to <2 mmol L-1) and increases in alkalinity from <1 to >10 mmol L-1 (as CaCO3). Over a 3 year period, the rate of Fe removal declines by approximately 35%. Primary controls on barrier performance are organic carbon reactivity, groundwater temperature, and variable residence time within the barrier.

Jan 1, 2000

By A. Bruynesteyn

Results are presented from a series of tests designed to determine the beneficial effects of the microorganism Thiobacillus ferrooxidans upon the leaching of uranium from a pyritic uranium ore. Minus 1-inch (-25mm) 0.0711 percent uranium containing, pyritic ore from the Rio Algom Mine at Elliott Lake, Canada was leached with lixiviants of various Eh and pH as well as being subjected to a biologically-assisted ferric iron leach. In all cases, the biological leach gave superior extraction. At pH 1.6, the biological leach gave 100.6 percent extraction and the ferric iron leach 69.8 percent. This improvement in extraction is associated with a relatively rapid biological breakdown of the pyritic material, thus liberating uranium mineralization associated with these pyritic materials and regenerating the ferric sulphate lixiviant in situ.

Jan 1, 1981

There are many risks associated with the storage of nuclear or other toxic wastes. One of the major risks is the escape of material from the repository. No matter how well a storage facility is engineered, the potential escape of dangerous material must be studied. This kind of study will include some estimation of the "travel path" of the particles. The travel path of a radio-nuclide particle will depend on the geological and hydrological parameters of the surrounding rocks. These parameters must be estimated from a limited number of samples available within the study area. Any estimation will -of necessity -contain a certain amount of uncertainty or "estimation error". This uncertainty will be carried through to the analysis of potential movement of particles, so that the estimated travel path itself will be subject to some error. This paper discusses an approach which may lead to a quantification of the uncertainty on the predicted travel path.

Jan 1, 1989

By Brian Stimpson

A recent study by the National Academy of Engineering concluded that if the U.S. Coal Industry is to double production by 1985 it must open 30 new 2,000,000 tons per year surface mines in the eastern states and 100 new 5,000,000 tons per year surface mines in the western states, in addition to major growth in underground mining. Major expansions in coal mining are also planned in other countries. Engineering geology can play an important part in coal mine development, operation and abandonment (Table I), and with the increasing scale of surface coal mining and the requirements of environmental legislation, it seems certain that engineering geology and geotechnics will play a growing role in surface coal mining.

Jan 1, 1976

By Michael V. Wolski, Ryan O. McCarter, Kenneth A. Johnson

"The Central Subway is Phase 2 of the San Francisco Municipal Transportation Agency’s (SFMTA) Third Street Light Rail project and will extend the existing Phase 1 initial operating segment from its current connection to the Embarcadero line at Fourth and King streets along Fourth Street to Market Street, under the Bay Area Rapid Transit (BART) and Muni Metro tunnels and then north beneath Stockton Street to Chinatown (Fig. 1).Total new track to be constructed as part of the Phase 2 work consists of approximately 734 m (2,410 ft) of surface track and 2,636 m (8,650 ft) of tunnels. The tunnels were constructed as twin, singletrack bores by two tunnel boring machines (TBMs) (Johnson, 2014) moving north from the southern end of the launch box under the I 80 freeway between Bryant and Harrison streets. North of Chinatown Station the TBMs continued another approximately 683 m (2,240 ft) to a retrieval shaft near Columbus Ave. at Washington Square. The project also includes five cross passages to connect the two tunnels, and three underground stations (the Yerba Buena/ Moscone Station, Union Square/Market Street Station and Chinatown Station.)Excavation of the twin tunnels was performed with two TBMs, with both TBMs driving northward from the launch box. TBM excavation was performed such that the location of the machines was staggered to separate the active excavation faces by a minimum of 91 m (300 ft) between headings. This minimum separation was maintained until the first TBM arrived at the retrieval shaft plug, at which time the separation requirement was relaxed.Excavation began with the “southbound” (SB) tunnel which will ultimately accommodate the southbound TBM light rail trains followed by the second TBM in the “northbound” (NB) tunnel. With the completion of the drives in June 2014, cross passage excavation then began and was completed in April 2015. Overall, construction of the Central Subway tunnels was a success considering the nature and complexity of the project. Additional details of the completion of the Central Subway tunnels are presented in another paper from the RETC 2015 conference (Leong et al., 2015)."

Jan 1, 2015

By W. T. Walter

High-G centrifuges from five preparation plants were sampled to determine and quantify the various operating factors affecting performance. The operating factors that were considered include feed rate and percent solids, size of feed material, screen-basket type, hardness of coal and age of the flights. The performance parameters that were measured include product surface moisture, recovery and degradation of the coal. Regression equations with good significance levels were developed.

Jan 1, 1982

By R. D. Coursen

Tin has been one of the very few commodities which has been covered by an international commodity agreement. It is the only metal so covered. The reason behind tin&apos;s prediliction for an agreement has been the inconsistency of the price pattern for tin during the entire 20th century. It is not surprising in view - of the wide and wild fluctuations in its price that tin has been called the Cinderella metal. An examination, for example, of prices in 1977 alone attests to the erratic behavior of the tin markets. The high was recorded on October 27 at M$1,895 per picul and the low on January 3 at M$l,314 3/8, on the Penang market, a spread in Malaysian dollars of $581 for a picul weighing 133 1/3 pounds. The first steps in international cooperation on tin were taken after the price bonanza of the First World War. Despite a lack of increased consumption, and in spite of the fact there was no shortage of mining production during the war, prices boomed. Shipping shortages and thinning stocks brought about a situation where in the U.S., industrial stocks were only 1/6 of what they had been in 1914. The boom busted early. In 1921 the tinplate industry of the world had cut its output in half and total world consumption of tin fell by 1/3. Tin producers became so concerned that they created what was called the Bandoeng Pool. It accumulated stocks held by countries now known as Indonesia and Malaysia, amounting to 28 percent of the combined production of the two countries and about 15 percent of the total world for 1921. The pool holdings were shortly exhausted and thereafter in the years 1924 to 1928, general boom conditions existed for tin.

Jan 1, 1978

By J. Noll, D. Yantek, J. Organiscak

The Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) conducted laboratory testing of a self-tramming, remotely controlled mobile Dry Scrubber (DS) that J.H. Fletcher and Co. developed under a contract with NIOSH OMSHR to reduce the exposure of miners to airborne dust. The scrubber was found to average greater than 95 percent dust removal efficiency with disposable filters, and 88 and 90 percent, respectively, with optional washable filters in their prewash and post-wash test conditions. Although the washable filters can be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-min washing period. The scrubber’s velocity-pressure-regulated variablefrequency- drive fan maintained relatively consistent airflow near the targeted 1.42 and 4.25 m3/s (3,000 and 9,000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60-Hz fan motor frequency or horsepower rating at 2,610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8,420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the scrubber showed that the outlet side of the scrubber was noisier, and the loaded filters increased sound levels compared with clean filters at the same airflow quantities. With loaded filters, the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6,000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level — under Title 30 Code of Federal Regulations Part 62.101— of 90 dB(A) at or below this airflow quantity. The scrubber’s washable filters were not used during field-testing because of their lower respirable dust removal efficiency and the airborne dust generated by filter washing. Field-testing the scrubber with disposable filters at two underground coal mine sections showed that it could clean a portion of the section return air and provide dust reduction of about 50 percent at the face area downstream of the continuous-miner operation.

Jan 1, 2016