Search Documents

By Thomas L. Hurst, Joseph M. Hans

INTRODUCTION The former Shiprock uranium mill site is located in the community of Shiprock, New Mexico on a bench overlooking the San Juan River (Figure 1). Both Shiprock and the mill site are located on the Navajo Indian Reservation. The millsite was built on a 230 acre tract leased by Kerr-McGee Oil Industries Inc., and was operated from 1954 to 1963. The Vanadium Corporation of America and its successor, the Foote Mineral Company, operated the mill from 1963 to 1968. During its entire operation, 1.5 million tons of uranium ore was milled producing 3711 tons of U308 concentrate. The concentrate was sold to the former U.S. Atomic Energy Commission. During milling, the ore was crushed to less than 35 mesh and acid leached to remove the uranium. The [ ] uranium was removed from the leach solution by solvent extraction and the uranium-barren solution discharged into raffinate ponds for disposal by evaporation and seepage. The spent solids (tailings) were pulped with waste process fluids and water and discharged to form tailings piles. The piles (ponds or dams) were formed with earth starter dikes. The dike walls were then raised using the separated sand fraction of the tailings. The slime fraction of the tailings were discharged into the diked impoundment. Since only a small fraction (0.25 percent) of the ore was U308 by weight, most of the ore bulk ended up as wastes. The wastes contain nearly all of the uranium decay chain radionuclides present in the ore except uranium. The mill was shut down and partially dismantled before the lease expired in 1973, and the remainder of the mill and wastes reverted back to the Navajo Tribe which was the lessor. Portions of the millsite were then occupied by the Navajo Engineering and Construction Authority (NECA), a Tribal enterprise. In order to provide skilled personnel to operate earth moving equipment, a heavy equipment operator's training school was also established on the mill site and was administered and operated by NECA. The U.S. Public Health Service (PHS) and the Environmental Protection Agency (EPA) staff conducted radiation surveys at four inactive uranium millsites on the Navajo Reservation in April 1974. During the survey of the Shiprock millsite, it was noted that the training activities were degrading its radiological condition. Both the PHS and EPA staff recommended that the training activities be directed towards the decontamination of the millsite area and interim stabilization of the tailings piles. Preparation for the decontami-nation work commenced in April 1974. In order to facilitate the decontamination activities, the mill site and its contaminated environs were divided into major areas labeled A through F (Figure 2). Areas A, B, and C are defined as "perimeter" areas and contained surface contamination ranging from 5 to 30 cm deep. Area D defined the mill yard and contained contamination ranging from 0.6 to 5.5 m deep. Area E contained several raffinate ponds which were removed to line up the northwest boundary of the tailings pile and to move the contaminants away from the vicinity of the occupied on-site buildings. The contaminants in Area E ranged from 0.05 to 5.5 m in depth. Area F encompassed the ore storage yard. Contaminants in this area ranged from 0.18 to 1.2 m deep. Washes, however, had contamination exceeding 7.6 m deep.

Jan 1, 1981

By Judson G. Brown

In order to filter small amounts of fine slimy solids the reversible cake-filtration process was developed. The filterable solids contents lion in feeds can range from less than 1 ppm up to about 5%. The relative advantages of this process, are usually the greatest in the range of 0.05% to 1.0% filterable solids. Filterable solids that average in particle size about 20 microns& are non-compressible are very easy for this filtration process. Some feeds have been all sub-micron in particle size. A 1/8 inch thick cake is considered to be very thick. The usual cake is between 13/2 and 1/16 inch thick. A new line of injection molded plastic filter plates were developed for use with the reversible cake filtration process. The first commercial sized installation of this system was made 3 years ago in the Wakefield Y.M.C.A. swimming pool. Over 70 filters ranging in size from one plate to 63 plates have been produced. In addition to the process advantages there are the low cost and corrosion resistance advantages of the plastic plates.

Jan 1, 1962

By R. O. Burt

The paper examines the role of gravity concentration in both an historical contest and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of ore mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration to other forms of processing and seeks to answer the classical question - "Quo Vadis?"

Jan 1, 1982

By Robert L. P. Kleinmann

Mining has been a significant component of the Appalachian economy for about 200 years. The region continues to be adversely affected by the environmental degradation associated with these past activities. In addition, companies today are being denied permits at sites where acid generation appears likely. And air emission limitations at power plants now threaten the economic health of many moderate- to high-sulfur coal mines. Thus, when considering the environmental impacts of mining coal in Appalachia, it is important to consider abandoned and active mine issues. For example, abandoned mines generate acidic, iron-rich waters that adversely affect more than 6,400 km (4,000 miles) of rivers and streams in Appalachia. In contrast, operations that were active after the enactment of the 1977 Surface Mining Control and Reclamation Act (SMCRA) cause little water pollution. However, the costs of water treatment at such sites exceed $1 million a day. Even where water quality is not dimished, water supplies can be affected by mining. Subsidence-induced fractures can lower water table elevations or drain a surface stream dry. Subsidence can also cause damage to surface and subsurface structures.

Jan 1, 1995

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimal when the concentrations of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/liquid ratio of 67 g/L, stirring speed of 400 rpm and leaching duration of 60 min. Under these conditions, 90.49 percent and 6.78 percent of Mn and Fe were dissolved, respectively, from the ore sample in a size fraction of smaller than 106 µm. It was determined that the leaching of manganese from the ores was a second-order reaction with activation energy, Ea, of 53.38 kJ/mol. The leaching residues obtained under the optimal conditions were subjected to wet high-intensity magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20 percent Fe and 1.79 percent Mn with iron and manganese recoveries of 56.83 and 66.73 percent, respectively. To the best of our knowledge, this is the first time that a magnetic separation process was used on a residue obtained from the reductive acid leaching of manganiferous iron ores to recover iron.

By T. W. Martin

In 1973 the percentage of total coal production mined by surface methods in the United States again increased, reflecting a long term trend. Barely three decades ago less than 10 percent of the U.S. coal was produced in this manner. Last year surface coal mines produced 299 million tons, 50.7 percent of our nation's coal. At present there are about 2450 strip mines producing coal in 23 states. While accident rates for surface coal mines are less than underground coal mining rates, surface coal mining is certainly one of the more hazardous occupations. Figure 1 shows the injury rates (fatal and non-fatal accidents) of major U.S. industries. Note that surface coal mining is more hazardous than all other industries except contract construction. Accident rates are about the same as the contract construction industry which uses similar equipment. A limited amount of detailed data was available on elements of surface coal mining jobs and this lack of compiled information made it difficult to assess the significance of the conditions contributing to accidents and to make recommendations that would reduce accident frequency. Therefore as part of the Bureau of Mines continuing research efforts related to the health and safety of the coal miner, a contract was awarded to Theodore Barry and Associates of Los Angeles to conduct an "Industrial Engineering Study of Hazards Associated with Surface Coal Mines."

Jan 1, 1974

By Dan B. Kivari

One of the key operations in any milling circuit is grinding. Over the last two decades, large diameter Semi-Autogenous Grinding (SAG) mills have become the preferred primary grinding mills. The drive systems became more complex as the size of the mills became larger, during which time operating and design experience for SAG mill accumulated. Considerable reliance is now placed in power electronics to provide flexibility in SAG mill operation to meet the demands of lower operating costs. Whereas earlier most SAG mills were designed to operate at fixed speeds, present day SAG mills can operate at a fixed speed or variable speed through the use of an AC synchronous motor or DC motor. However, this flexibility comes with an increase in capital and operating costs. Since the capital and operating costs of a project directly affect the project's rate of return, the selection of a SAG mill and its drive system should depend, in part, on the impact that the extra cost makes on the project. This impact can be measured by performing an economic analysis based on Net Present Cost (NPC) calculations. Although the NPC calculation is an important factor in the grinding mill selection, other factors such as reliability of mill drives and power source are important elements in the decision making process. This paper examines how the NPC calculation, plus reliability and power source, influence SAG mill selection.

Jan 1, 1991

By R. J. Sweigard

Three case studies were undertaken to investigate the role of land use potential evaluation in reclamation planning and to determine the impact of regional differences on the evaluation process. The three surface mines studied were representative of operations in the Appalachian, Interior, and Northern Great Plains provinces. The scope of the investigations included a survey of regional characteristics, a detailed investigation of the mining operations and site conditions, and an assessment of local land use planning activities in the area of the mine. Special attention was given to key factors that presently determine the use of reclaimed land. Also, for each case study, the postmining land use potential was evaluated using site planning principles. Specifically, the environmental, economic, and social impacts of several potential postmining land use plans were considered.

Jan 1, 1983

By Jack A. James

Lancaster Lime and Stone Corporation developed a quarry operation in 1971 and 1972 for the production of high calcium limestone and construction aggregates, or roadstone. The quarry operation is situated in southeastern Pennsylvania in the northern part of Lancaster County. The geology of the high calcium limestone deposit had a powerful influence on all aspects of planning this operation. My purpose is to trace the influence of geology throughout the planning and thereby point out the discipline that geology imposed on the planning, and indeed, continues to impose on the operation. Lancaster Lime and Stone Corporation is one of four wholly- owned subsidiary companies of Kurtz Materials Corporation. Kurtz Materials Corporation, through its operating subsidiaries, is a supplier of basic materials to the construction industry including crushed stone, ready mixed concrete, concrete masonry units and a wide range of precast and prestressed concrete products.

Jan 1, 1973

By J. B. Boisvert, O. Leuangthong, T. Acorn

Optimizing final pit limits for stochastic models provides access to geologic and economic uncertainty in the pit-optimization stages of a mining project. This paper presents an approach for optimizing final pit limits concurrently over all realizations in a stochastic model and using a risk-management framework to manage the geologic and economic uncertainty. A heuristic pit optimizer is used to find multiple uncertainty-rated pit shells. These uncertainty-rated pit shells follow the mean-variance criterion to approximate the efficient frontier for final pit limits. Stochastic dominance rules are then used in a risk-management framework to further eliminate suboptimal solutions along the efficient frontier. This results in a smaller set of final pit shells that can be further analyzed for production scheduling. Additionally, the original solutions are analyzed for changes in the mining limits, and two regions are targeted as potential regions for further exploration.

By Mustafa Kumral, Yuksel Asli Sari

Economic evaluations of underground mining operations are made based on the estimated or simulated grades of the block model as the actual values are not known. Depending on how the planning decisions are made, the risk of the operation can be managed and decreased. This research introduces a mixed-integer linear programming (MILP) model for stope sequencing optimization that considers the uncertainty associated with net present value (NPV) using chance-constrained programming (CCP). The introduced method permits achieving a balance between maximizing NPV and reducing the associated operational risk through transforming the problem into a multiobjective problem, where the objectives are maximizing the NPV and minimizing the risk. This risk is expressed in terms of the standard deviation of project outcomes, taking into account multiple possible scenarios. In a case study, the efficiency of the method was demonstrated as a decision-making tool capable of translating a specified risk or reliability level into a stope sequencing plan.

Jan 1, 2024

The dissolution behavior of gold and copper from their elemental states and from Au/Cu alloys in cyanide solutions has been investigated using a rotating disc electrode. The anodic and cathodic reactions were studied separately and the resulting polarization curves were combined to examine the overall dissolution reactions. The dissolution rate of pure gold in the aerated cyanide solutions was inhibited by the anodic passivation on the gold surface, while the dissolution rate of pure copper was found to be mass-transfer-controlled. On the other hand, the dissolution of gold and copper from the alloys was partially controlled by electrochemical reaction and largely by mass transfer.

Jan 1, 1994

By John W. Crawford

The title of the paper which I have been asked to present is somewhat misleading it infers in fact that there is a definite coalbed height below which raps or canopies cannot be applied to electric face equipment. Although this may be so with regard to certain pieces of existing equipment under certain conditions, to date we do not have enough experience to determine this magic number. Therefore MESA is continuing to hold the line on the time frames stipulated in Section 75.1710-1 of the Mandatory Safety Standards - Underground Coal Mines, which at this point in time requires these protective structures in mining heights of 60 inches or more. In order to give you an idea why we are taking such a firm stand on this matter, I believe it is necessary to describe some of the background work that was done prior to promulgation of the regulations and to give a resume of our experience since the requirements have become effective. Initially MESA made field investigations of all underground mines to determine what the state of the art was in the use of cabs and canopies for protecting equip¬ment operators from falls of roof. These studies revealed that the application was basically in its infancy and what progress had been made was due to the impetus of the mine operators themselves. Manufacturers of electric face equip¬ment provided these structures only on the direct order from the mining company and built them to their specifications. In talking to the operators and the miners in mines where cabs or canopies were in use, it was the consensus that these structures did improve safety and that although originally there was some reluctance on the part; of the miners to work in the confines of a cab or canopy, mast would not work without them once they had been adapted to the equipment.

Jan 1, 1975

By J. Kou

The adsorption process, density and structural property of the oleate layer adsorbed onto a hydroxyapatite (HAP) surface at six different concentrations and three pHs (pH 8, 9 and 10) have been studied using the technique of quartz crystal microbalance with dissipation (QCM-D). The present study demonstrated the versatility and accuracy of the QCM-D for surface adsorption characterization. The real-time measurements of frequency and dissipation shifts with a hydroxyapatite-coated sensor revealed changes in the hydroxyapatite surface during the entire adsorption process. Chemisorption and surface precipitation of sodium oleate were also observed on the surface of hydroxyapatite through the use of Fourier Transform infrared spectroscopy(FTIR). Chemisorption dominated at low concentrations and high pH values and formed a rigid and thin adsorption layer. Surface precipitation of calcium oleate and micelles dominated at concentrations higher than critical micelle concentration (CMC) and lower pHs and formed a thick but dissipated adsorption layer with a high hydration level. Three distinct adsorption behaviors were identified from the different slopes of ?D-?f plots. The adsorption density was less than a monolayer at concentrations <0.164 mM, but increased significantly at concentrations higher than 0.821 mM at all three pHs. The critical concentration at pH 8 was 0.33 mM, which was lower than at pH 9 (0.821 mM) and pH 10 (3.3 mM).

Feb 1, 2012

By T. Fernandez, V. Juchen, C. Petter, F. Cantini, V. Lenz, V. I. Araújo, R. Petter, R. Darrigo, A. Young, I. G. da Costa, J. Oppermann

There are many methods to estimate costs quickly. One of these is the Parametric Method, where costs are estimated from general algorithms (or curves). Derived from an original tool based on the O’Hara model, a software called MAFMINE was developed. MAFMINE is based on parametric models to estimate investment and operational costs in mining. The software itself is based on the use of a computer model known as client-server. However, the model needs new inputs from advances made by the mining industry, mainly in terms of electrification, automation, digital transformation and preconcentration to face Environmental, Social and Governance (ESG) concerns. Thus, this work was to prepare a new core module ready to incorporate the new technologies aiming to deliver operation and capital costs associated with environmental impact mitigation. The tool generates an order of magnitude estimate for CAPEX and OPEX to establish a very first Discounted Cash Flow (DCF) in a mining venture. For quick evaluations, at a preliminary level, the results are very promising.

Mar 2, 2022

By Frank L. Peterson

This paper deals with problems of groundwater development in an insular circum-Pacific environment, and is not oriented as such to mining and mineral development. Nonetheless, because a reliable water supply is necessary for most mining and related support activities, and since water supplies are limited in many insular parts of the Pacific Basin, groundwater development is a subject which must be frequently addressed. Because many in the audience may be already familiar with groundwater development for continental environments, I have chosen to deal with groundwater occurrence and development problems which for the most part are unique to insular environments. In such environments, the local geology plays a critical role in determining groundwater occurrence and its suitability for development. The three examples discussed in this paper-Hawaii, Guam, and the Marshall Islands-were selected because they illustrate groundwater occurrence in a wide range of geologic conditions. For example, the Hawaiian aquifers consist primarily of basaltic lavas, while Guam is made up of andesitic lavas and coral reef limestones, and the Marshall Islands are coral atoll deposits. Despite differences in aquifer size and rock types, the principal mode of groundwater occurrence at the three sites is similar; thus, development strategies are also similar. Figure 1 shows the location of the three sites.

Jan 1, 1982

By Robert L. Major

The expanded role which coal has been assigned in the energy future of the United States has raised numerous policy questions. The very complexity of these questions makes them suitable to analysis by econometric models. However, as the Wall Street Journal indicated in its recent article, business&apos; success with such models have been mixed. I have been asked to present my views as to how coal producers can use such models and in what ways the industry is likely to be impacted by such models. I do not presume to speak for the whole coal industry, but only to share with you the personal observations of one who has worked "both sides of the street", having been employed&apos; both by government and a consulting firm prior to joining the coal industry. In my opinion, the use of econometric models to analyze the coal industry will impact the coal producers in two main ways. First, their use by government will have a profound impact on future government policies related to the mining, transportation and utilization of coal. Second, such models, when properly calibrated and refined, may become useful tools for the coal producers in doing market research and long-range planning. While the former has already begun to impact on the operating environment or the coal industry, the latter is still in the embryo stage.

Jan 1, 1977

By G. V. R. Landman

In order to obtain a better understanding of the explosion risk at the coal face, anomalies in the ignition sensitivity for different modes of ignition of hybrid mixtures of dust, methane and air were studied. Results indicated that the explosible behaviour of the working environment is highly dependent upon the ignition source and the fuel composition. For example, depending on the ignition source, the same hybrid mixture can be inert or extremely explosible. In conclusion, it is stressed how the explosion risk can be expressed in terms of a safety factor which takes into account the influence of both the fuel and the ignition source.

Jan 1, 1994

By M. Solomon

Crushers are designed and manufactured to survive the severe duty of mining environments worldwide. Under these conditions the crusher performance and availability is one of the critical factors in the mine?s production and profitability. Traditionally the development of these machines tends to be experience-based, incremental improvements in design due to challenges of different applications, duty, or manufacturing. In order to better serve the mining industry a new approach was taken to the design of primary crushers. This approach was to focus on safety and maintenance activities. The result of this effort is a new generation of gyratory crushers that can be serviced from above. Using the features of this new generation of crushers to their fullest extent crushing installations have improved safety, reduced design and construction costs, and lowered maintenance requirements. This presentation explores the benefits of two crusher installations utilizing top service crushers.

Jan 1, 2010

By Jr. Chesson

"Phosphate" is a misnomer as often used. The word is increasingly used to refer to any material containing phosphorus - an element essential to any form of life. Phosphate rock, a mineral - fluorapitate - is recovered from Florida&apos;s sedimentary deposits in particle sires ranging from 0.1 to 13.0 millimeter. This product of mining, washing, screening, and flotation is commonly called "phosphate". Its phosphorus content, measured and reported as P2O5, varies from 29% to 35%, and is essentially insoluble. "Phosphate" is also used to describe products containing soluble phosphorus obtained from acidulation of phosphate rock with mineral acids; primarily, sulfuric acid. Many miners have nearby chemical plants wherein phosphate rock is converted into upgraded products such as phosphoric acid, superphosohates, and ammonium phosphates with 45% to 70% P205, soluble and suitable for use as fertilizer. The rock and upgraded products are all commonly called "phosphate"; the plants, "phosphate plants&apos; and the producers collectively are known as the "phosphate industry". The public in Central Florida generally loses identification of the individual operators that include major corporations such as IMC. Williams Companies, W.R. Grace, Mobil, Embark, U.S. Steel, Borden, American Cyanamid and others. They all become just a "phosphate company".

Jan 1, 1978