Search Documents

By T. Dlokweni, A. Z. Toper, A. P. Squelch, R. G. Gürtunca

A collaborative research programme called 'DEEPMINE' was established in 1998 to investigate and research the problems of mining below three and five kilometres depths. Backfill is considered as an important support strategy to alleviate rockburst and rockfall problems in current depths and it will even become a more crucial mining strategy at ultra-deep level mining. In this paper, the evaluation and the application of the current backfill design criteria to the ultra-deep level mining environment are studied and a new backfill design criteria is proposed. The new criteria suggests that backfill should still be placed 60 - 70% of the area mined with a maximum fill to face distance of three metres. Furthermore, the vertical stress generated in backfill should be between 2 - 3 MPa at maximum 25 metres from the face at a corresponding strain value of maximum 10%.

Jan 1, 2001

By R. G. Dalbke

An increasing number of water pollution control systems are certain to be installed by many industries in the future because of new federal, state, and local government regulations, and because of the rising general concern about the deterioration of our water resources. Extensive engineering, some of it based on methods not yet developed, will be required if these new systems are to provide optimum pollution control. Capital cost, operating cost, and present and future regulatory requirements will be primary factors to be considered by engineers. This paper outlines procedures and gives examples of advanced engineering practices that have achieved efficient pollution control systems in the steel and nonferrous industries.

Jan 1, 1968

By A. J. Lynch

Mineral commimition is an important and expensive industrial process and modern comminution circuits are complex There is considerable economic incentive to optimize circuit design and performance and to operate circuits at maximum efficiency, and these aims may be achieved by setting up mathematical models of the units in a circuit on a digits, computer and studying the behavior of simulated circuits. Models of grinding mills and cyclone classifiers which may be used for this purpose are discussed. The use of these models for design and optimization is discussed and particular mention is made of the factors which are important in circuit control. A digital computer-based automatic control system which has been successful in practice is described

Jan 1, 1972

By Thomas L. Craig

The Wellman-Lord SO2 Recovery Process is operating commercially at one location in this country and at two locations in Japan. Tail gases from a sulfuric acid plant, from an oil fired steam generator and from a sulfur recovery unit are the respective applications. 1) At the Olin Corporation's Paulsboro, New Jersey, stack gas from a spent acid regenerative sulfuric acid plant-45000 SCFM - is treated in the W-L unit to reduce sulfur dioxide concentrations from 4500 ppm to less than 500 ppm. 2) At the Japan Synthetic Rubber plant in Chiba Prefecture, stack gas from an oil-fired steam generating plant - 120,000 SUM - is reduced from 2100 ppm S02 to less than 200 ppm. 3) At the Toa Nenryo Kogyo refinery in Kanagawa Prefecture, tail gas from a sulfur recovery (Claus) unit - 41,000 SUM - with, an inlet SO2 concentration of up to 13000 ppm is reduced to less than 200 ppm. The three installations are operating successfully and are capable of reducing S02 emissions to levels significantly below the concentration guaranteed. With the one exception of a higher than guaranteed chemical make up requirement at Paulsboro, utility and chemical requirements will be less than design.

Jan 1, 1971

By Anthony W. Wakefield

The paper is intended merely as an introduction to methane hydrates, what they are and why they are important. It does not claim to be a cutting-edge research report, but may be useful for those to whom the subject is unfamiliar.

Jan 1, 2008

By R. E. Nivens

In the past, Newmont Gold Company relied on cement for their ore agglomeration process. With assistance from Betz Industrial, Newmont began Investigating the use of polymers for ore agglomeration. If gold recovery would not be jeopardized, then polymers could replace cement and possibly reduce operational costs associated with cement agglomeration. The following outlines the preliminary testing conducted to determine the feasibility of polymer agglomeration with Newmont's ore and the results of the test heap, which was constructed so the program could be examined under actual operating conditions. Similar polymer agglomeration testing has been successfully performed in other Nevada gold operations. By eliminating the need for cement, a polymeric agglomeration program could improve material handling operations, as well as offer the following additional savings. First, the polymer application uses only lime for adjusting basicity, the polymer does not contribute any alkalinity to the heap. Because lime is more soluble than cement, detoxification of the heap becomes much faster and less costly for the mine relative to rinsing cement alkalinity. The following graph compares the detoxification rate of cement and polymer over a 33 day cycle.

Jan 1, 1993

By J. G. Groppo

Laboratory settling and filtration testing was conducted on wet processed fly ash in order to determine the applicability of conventional dewatering techniques to reduce the moisture content prior to drying. Settling tests showed that acceptable clarity (<1.5 g/l suspended solids) could be achieved after as little as 6 minutes of settling. After settling to a consistency of 40 weight % solids, continuous laboratory vacuum filtration testing produced a cake containing below 20% moisture with throughput exceeding 150 lb/ft2/hr.

Jan 1, 1997

By C. J. Johnson, C. J. Bise

Abstract - As the US coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face- ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity. Room-and-pillar mining accounts for approximately 68% of the nation&apos;s underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing techno- logical climate on future room-and-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.

Jan 1, 1990

By Saurabh Rastogi, Vikram Shishodia, B. Pitchumani

Comminution is a unit operation which consumes major part of energy in mineral processing industries such as fertilizer production. Ball mills are widely used for size reduction of a given ore to the liberation size that is required in further beneficiation processes. In grinding of materials much effort is concentrated on control of top size of the product and this results in production of fines, also creates secondary problems of pollution due to the difficulty in the collection of fine particles. The present work has been carried out to control product size distribution for rock phosphate grinding in an Industrial Ball Mill of 600 TPD. The plant data are taken for a given feed distribution and mill operating conditions. The information at various Ball Size distributions are collected. The comminution functions such as specific rate of breakage and breakage distribution functions are estimated by back calculation technique to solve the mass balance equation. A simulation program is written to study the product size distribution obtained for various ball size distribution.

Jan 1, 1993

By W. M. Tupper

[The two types of sulfide deposits in the Bathhurst Newcastle area are; (a) epignetic fissure deposits, and (b) massive sulfide deposits. Geological evidence has been variously interpreted to suggest a syngenetic origin, a source bed&apos; origin, or a magmatic hydrothermal origin for the massive sulfide deposits. Sulfides disseminated through the black shales and argillites of the host rocks are enriched in S32 (mean value 22.34, S34. = 5.8 per mil) relative to the meteoritic standard of 22.21, and have a broad spread in range of values. S32/S34 ratios of sulfide minerals from the deposits occur in two distinct groups. The massive sulfide deposits exhibit ratios between 21.88 to 22.05, while the fissure deposits exhibit ratios between 22.18 and 22.21. These results suggest two separate sources for the sulfur, each, however, resulting in magmatic hydrthermal deposition because of the narrow spread of ratios in each group. Granite intrusive into the host rocks of the sulfide deposits have a mean K/A age of 386 ± 10 M.Y. Lead minerals in the sulfide deposits have a mean nodel lead age of 370±20 M. Y. Thus the lead minerals and the granite bodies were emplaced during the same major orogenic event. Sulfide minerals from magmatic hydrothermal deposit have a very narrow range of S32/S34 values, as do those of the Bathurst area. It seems reasonable, therefore, that well homogenized magmatic hydrothermal solutions are the most logical source of the sulfide deposits. Furthermore, the homogeneity of the lead isotopic abundance data gives strong independent evidence that the ores are of a magmatic hydrothermal origin.]

Jan 1, 1960

By R. D. Grove, M. F. Elliott, R. L. Weigel

The control of Florida phosphate flotation plants is largely based on the visual observations of experienced operators, both in recognizing good and bad froth conditions and in making judgments about the composition of feed, concentrate and tailing streams. Chemical analyses lag the process by at least two hours and therefore only assist in recalibrating the operators&apos; vision when major deviations occur. An image analysis system has been developed by IMC Agrico Company (IMCA) to improve upon the accuracy and precision of the composition estimation process. It still relies upon the operator taking a representative sample, but provides a measurement in about 15 minutes after that sample is obtained. This paper describes the system and its use and presents comparative results for various process streams.

Jan 1, 1993

By Frank McKinley

This paper discusses the basic requirements covering the area between the initial discovery of a deposit and a decision as to whether or not the deposit will support an economically sound mining venture. The procedure for gaining the necessary information and the sequence of steps is in .some respects parallel to gaining like information on deposits other than the sand type. For the sake of simplicity the stages and sequence are presented as follow: first, the initial reconnaissance drilling; second, the exploration drilling to permit initial ore body estimates; third, metallurgical testing; fourth, the estimate of plant and operating costs; and last, the economic balance. The objective of the reconnaissance drilling is to collect sufficient information to reach a decision as to the advisability of further exploration or the abandonment of the area. This initial phase will comprise, in addition to some drilling, a thorough reconnaissance of the area, a study of the best geological and topographic maps of the region, and a study of any literature available, all under the guidance of a geologist.

Jan 1, 1958

By Steve Wirch, Robert Jankowski

The issue of dust control in underground coal mines has been extensively studied by both government and industry. This research work has resulted in many techniques which control the dust or help miners avoid it. Control techniques either prevent the dust from becoming airborne or cleanse the air before it can be inhaled. Avoidance measures minimize the exposure of miners to the airborne dust by blowing the dust away from work areas or making it unnecessary for a miner to occupy a dusty region. One of several successful dust control measures in continuous miner sections is the use of a machine mounted scrubber which cleanses the air and helps to prevent the contaminated air from reaching areas frequented by mine personnel. Research on the application of scrubbers on longwall shearers began in the 1970s and continued into the 1980s. The most successful projects showed only moderate improvement when a scrubber system was mounted on a longwall shearer, and the less successful projects actually increased worker dust levels. There are many reasons that scrubbers have not been successfully applied on longwalls. The most significant of these is that longwalls have across the face ventilation and generally have high face air flows. Scrubbers tend to work best when they are the primary cause of ventilation. Therefore, their capture efficiencies on longwalls tend to suffer because of the exposure of the drums to the primary airflow. Other reasons scrubbers have not been implemented on longwall s include the successful application of an excellent water spray system, effective cutting techniques, and dispersion of dust sources. These techniques can help control drum generated dust, increase production, and limit the relative effectiveness of a scrubber.

Jan 1, 1995

By T. J. Harvey, W. van der Merwe, J. Joubert

GeoBiotics, LLC and Kumba Resources (Pty) Ltd are jointly developing the GEOCOAT® heap bioleaching technology and downstream processing technology for recovery of zinc from tailings at the Rosh Pinah Mine in Namibia. This paper outlines the development of a computer simulation for the bioleaching of sphalerite and the downstream processing. Computer modeling has shortened the product development cycle by allowing many flowsheet scenarios to be analyzed negating much of the expensive and time consuming laboratory testing. A model was developed using the Limn® system which is an Excel® Add-In flowsheet drawing and solution engine. Given that most engineers are familiar with Excel® this software is extremely easy to use and has less hidden calculations making model verification much easier.

Jan 1, 2003

By Don Phelps, Christopher Tattersall, David McAllister

Located south of downtown Seattle, the Beacon Hill Station & Tunnels is the key section of the southern segment of Sound Transit’s proposed new LINK light rail system. This paper presents an overview of the design, which includes 4,300 ft of segmentally-lined bore twin tunnels and a deep mined station. With platforms located156 feet below grade, the station itself is only the second large-scale mined station in soil the US. Its complex geometry combined with variable soil conditions—sands, silt sand clays with slickensides—challenged the designer’s to come up with a SEM-based design that addresses the owner’s risk, cost and schedule concerns.

Jan 1, 2003

By E. Scott Bair

Renewed interest in the vast reserves of anthracite coal in eastern Pennsylvania led to the use of a numerical model for simulating the hydrologic effects of constructing an open-pit anthracite mine. The proposed mine would be approximately 1800-m (5900-ft) long, 1000-m (3300-ft) wide, and 300-m (1000-ft) deep. A two-dimensional, finite-difference, ground-water flow model was used to calculate ground-water seepage rates into the proposed mine, to evaluate the effectiveness of various deep-well dewatering systems, to calculate drawdown in adjacent wells and properties, and to estimate the capacity of the water-treatment plant. Site-specific values of pertinent hydrogeologic parameters were used in the simulations.

Jan 1, 1980

By R. A. Metz, M. A. Bryant, J. C. Goodwin, T. B. Faddies, L. D. Kornze

The Mercur Gold Mine is located 56 km (35 air miles) southwest of Salt Lake City in north central Utah. In July 1981 Getty Mining Company made the decision to put Mercur into production. The first gold bar was poured in April 1983. This paper provides details on: 1) the history of the camp, 2) past production, 3) geology of the deposit, 4) the exploration and development program, 5) ore reserve estimates, 6) detailed geologic pit mapping, 7) production blasthole sampling techniques and 8) the use of geostatistics (kriging) in handling assays and gold extractions to produce the required mill feed.

Jan 1, 1992

By T. E. Durney

In the Fall of 1987 The Wellmore Coal division of The United Company installed a fines separation circuit in its #20 plant near Big Rock, Va. The addition of the fines circuit included a bank of classifying cyclones and two flotation units; one a conventional 4 cell, 34 m3 Wemco cell, the other an 2.4 meter diameter by 7.6 meter tall, 28.3 m3 column flotation cell. The new fine coal separation circuit is depicted in Figure 1. The column flotation cell is manufactured by the Deister Concentrator Company, Inc., under the trade name Flotaire. The Deister Flotaire column cell utilizes a counter current flow arrangement and a different means of generating air bubbles than that of conventional mechanical flotation cells found in coal processing plants. Other features include diffusers for additional air supply and a froth washer. This cell is one of the few commercial scale column cells processing coal.

Jan 1, 1990

By S. K. Kawatra, S. J. Ripke

Iron ore concentrates pellets are currently in duration heat hardened (sintered) under oxidizing conditions. Pellets produced from magnetite ore concentrate are completely oxidized during induration and finish as hematite pellets. These pellets then require a blast furnace to reduce the hematite to metallic pig iron. Partially reduced pellets would save energy and fuel during transportation and further reduction. It has been stated in the literature “the most important single factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of the magnetite to hematite and the subsequent recrystallization and grain growth of this constituent.” However experiments shown in this paper reveal that oxidation is not necessary to produce high-strength pellets. Magnetite concentrate pellets developed similar strength when indurated at 1350°C under either oxidizing (air) or inert (argon) atmosphere; the pellets sintered under argon remained magnetite. In addition, magnetite concentrate pellets indurated under reducing (CO) atmosphere also remained as magnetite, but required induration temperature of approximately 150°C less than the other pellets.

Jan 1, 2003

By Gunnar Nord

Shifting ground conditions when tunnelling often call for different methods of attacking the tunnel face. In order to overcome problems with local unstable soft ground in a hard rock tunnelling project the Boodex method offers a cost effective alternative. Boodex and variants of it is a combination of two well-known techniques, drilling with Boomer rig using Odex gear. It will give a steel lined hole ready for grouting and the steel pipe has a load bearing capacity that means that a spiling effect is achieved. In this paper the method and some applications will be described with possibilities and limitations.

Jan 1, 2003