Search Documents

By S. K. Nicol

The results of column flotation tests conducted on a bulk sample of ultrafines discarded from the fine coal desliming cyclones at the Riverside coal preparation plant of Theiss Dampier Mitsui Coal Limited are presented. A 9% ash concentrate was obtained from a 51% ash ultrafine feed at 75-80% recovery of combustibles in a single stage of column flotation. From this result it is predicted that installation of column flotation at Riverside would lead to the annual recovery of additional coal worth $US5.1M. The operating conditions for coal and copper column flotation are compared and some differences which may result in a variation in column design are noted.

Jan 1, 1987

By Shawn T. Sorrell

Phillips Coal Company (PCC) submitted the first surface mine permit application under the Office of Surface &lining approved regulatory program of the State of Louisiana. This application for the Oxbow Lignite Surface Mine which is located approximately 64 kilometers (40 miles) southeast of Shreveport, Louisiana was submitted in March 1981. The State of Louisiana Office of Conservation, Surface Mining Division, assigned this application number LSM-1, indicating it is the first one submitted in Louisiana history. The permit area for the Oxbow Mine encompasses 6,251 hectares (15,627 acres). Of this total permit area, 5,862 hectares (14,656 acres) were classified by soil type as prime farmland by the U.S. Soil Conservation Service (SCS). Prime farmland acreage in the permit area became a major central issue in our early planning stages and throughout the permitting process of the Oxbow Mine, due to the magnitude of acreage involved.

Jan 1, 1982

By R. D. Hagni

Pyrometallurgical products from lime roasting of refractory gold ores, pyrite, and arsenopyrite have been examined for their mineralogy, porosity, permeability, retention of contaminant sulfur and arsenic, and potential effectiveness of gold extraction. Cathodoluminescence microscopy, supplemented by X-ray diffraction and scanning electron microscopy-energy dispersive analysis study, has shown that the products phases have characteristic cathodoluminescence properties as follows: anhydrite (CaS04), deep blue; unreacted portlandite (Ca(OH)2), deep purple; oldhamite (CaS), light yellow to rarely pink or orange; a sulfur-rich, arsenic-poor phase, violet; an arsenic-rich, sulfur-poor phase, non-CL. Within the temperature range examined (400-850°C), hematite exhibits greater porosity and permeability at the intermediate roast temperatures of 600-650°C.

Jan 1, 1993

By T. S. Golosinski

Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost, and significantly influence dragline productive time. Both work in very difficult conditions and wear out rapidly. As a result frequent rope changes are required at a substantial cost and time loss to the operation. Although performance of rigging has a profound impact on dragline performance, there are no industry-wide standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The life of drag and hoist ropes depends on: (1) rope construction, which should closely match requirements of the specific application, (2) correct definition and application of the rope discard criteria, so that full advantage of the rope can be taken without endangering safety of operation, and (3) rope operating conditions and its maintenance. The study presented in this paper was intended to address the above points, based on a survey and assessment of the present industry practice.

Jan 1, 1993

By J. H. Meza Viveros

This paper describes some actual parameters and technologies used at Mexicana de Cobre Smelter, and the principal design parameters and new technologies which wiil be used with the smelter expansion project, in order to increase the production capacity of anode copper from 180 000 mtpy to 300 000 mtpy. Likewise its describe some parallel projects under construction also in the smelter plant.

Jan 1, 1997

By R. F. Davis

The evaluation and selection of coals for producing metallurgical coke is indeed a com- plex process simply because coal is a complex and variable substance which is sensitive to how it is treated from the time it is mined until it is transformed into coke. A review of the the more common evaluation tests made on coal and how the test results are applied in commercial practice. Parameters used to select coal blends for wet and preheated charges should also be of interest.

Jan 1, 1980

By S. D. Bearden

The world's reserve base is adequate for at least 100 years at the current consumption rate. China, India, and the U.S. are expected to remain the leading producing countries. The U.S. will continue to be the largest consumer of the production. None of the known substitutes for barium sulfate are expected to impact existing applications. World production in 1995 was 4,410Mt. This is about 50% of the projected capacity. Consumption is directly proportional to hydro-carbon well installation activity. Imports are expected to continue to supply more than half of the U.S. requirements.

Jan 1, 1997

By Lawrence P. Kennedy

The Lynne deposit is a volcanic-to volcaniclastic-hosted, Zn-Pb-Cu-Ag orebody located in the early Proterozoic magmatic terrain of northern Wisconsin. As of February 1991, core drilling has partially delineated a multi-million ton, near-surface, disseminated to massive sulfide deposit. The deposit is hosted by a gently dipping sequence of fragmental rhyolites, felsic tuffs, less abundant dacite to andesite flows, and fine-grained volcanic sediments. The deposit is broadly conformable With the host rock stratigraphy, but the ore zones thicken and coalesce in the central part of the deposit.

Jan 1, 1991

By Wendell E. Bearce

At the, Crescent Valley Mine of the Hanna Coal Company, several 10,000 ton unit trains of 41" x 0 strip coal are loaded per week during the lake season. This is accomplished without the use of any accumulation of prepared coal. A large raw coal pile is built up during the winter months adjacent to two truck dump bins. This is added to whenever trucks are coming in from the pits and trains are not being loaded. During the loading of trains, trucks from several pits dump into the truck hoppers and coal is also dozed in from the pile. At a rate up to 3200 tons per hour this coal is screened, the plus 6" hand picked, the plus 4" crushed, and' all weighed and sampled as it goes directly to railroad cars being handled on two tracks by car retarders. With such an arrangement it is possible to exercise some control over coal quality, if it can be assessed rapidly. For instance, if the moisture rises to a level where it seems probable the BTU per pound will be reduced to the point where the contract calls for penalties, the trucks from, the wettest pit may be stopped, more or less coal may be moved in from the stockpile, or other measures taken to assure that the average BTU of the trainload will be satisfactory.

Jan 1, 1967

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By Thomas R. Hightower

The Thunderbird plant was erected in Sullivan County in Indiana during 1958-1959. It was first put in operation in March of 1959. At the present time the source of the raw coal is from the Indiana No. 6 seam. The underground operation at present consists of two continuous mining units and two conventional units. The underground is all belt haulage and the first unit with which this paper is concerned is the slope belt. It is a 48-inch-wide inclined belt with 980-foot centers and a lift of 275 feet. The belt is powered with a 350 H, P, motor and has a rated capacity of 600 Tons per Hour. The belt is equipped with a Merrick Scale Company Weightometer, The raw coal moves from the belt to a 6'x12' extra heavy Allis-Chalmers Ripl-Flo equipped with 6" round-hole screens. The over product of the screen is fed into a 10'x20' long McNally- Pittsburg rotary breaker equipped with 4-l/2" round-hole screens. The oversize rock is discharged into a bin that is emptied with a refuse truck. The through-product of the breaker, along with the through-product of the Ripl-Flo, passes either directly to the McNally Giant washbox or to a 36" belt that transports it to a 1000-ton storage bin,' The change from either to the washbox or to the storage bin is made by use of a motorized gate controlled by the plant operator,

Jan 1, 1961

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which enables completely new designs of conventional shell and tube configurations. This article explains the principle and application of this self-cleaning heat exchange technology and also pays attention to an actual case of a revamp of the severely fouling exchangers of a conventional multi-effect evaporator into a self-cleaning configuration. Possibilities for the revamp of conventional exchangers suffering from massive and very hard scale deposits are found in a variety of metallurgical processes, such as: The refining of nickel, the production of alumina from bauxite and many others.

Jan 1, 2003

By J. Zhai, Z. Yin

"The electrokinetic and flotation behaviors of ilmenite using lead ions as the activator and sodium oleate as the collector were studied. The results of microflotation show that the flotability of ilmenite can be improved by lead ions obviously. The isoelectric point of ilmenite increases from 5.32 to 7.7 after the addition of lead ions because of the adsorption of Pb2+ and Pb(OH)+. The results of zeta potential measurements and the collector adsorption density calculation show that the adsorption of sodium oleate on the ilmenite surface via chemisorptions in addition to electrostatic interactions. Besides, the adsorption density calculation results show that as the addition of lead ions as the activator, the adsorption amounts of collector are greater than those without activation which is in aggrement with the flotation behaviors. INTRODUCTION Ilmenite, as an oxide mineral of formula FeTiO3, is usually used as the main resource of the extraction of titanium (Bulatovic and Wyslouzil, 1999). There are many researches showing that the conventional methods, such as gravity separation, magnetic separation and flotation, do not work efficiently as expected (Mehdilo et al., 2015; Zhu et al., 2011). Nowadays, to produce ilmenite concentration feasibly and efficiently, these separation methods above are combined for a reason that the raw ilmenite ores are characteristic of poor, fine and complicated. Moreover, surface modification, such as surface dissolution method, microwave irradiation and oxidation roasting, is applied to improve the flotability of ilmenite currently (Welham and Llewellyn, 1998; Zhang and Ostrovski, 2002). Generally, fatty acid salts are used as the collector for the flotation of oxide minerals and sodium oleate is usually used as the collector for the flotation of imenite ores (Fuerstenau and Pradip, 2005). The mechanism, such as individual ion electrostatic adsorption, chemical adsorption, ion–molecule dimeric complex adsorption, and the coadsorption of ion and molecule, have not been discussed systematically using sodium oleate as the collector in the flotation of ilmenite (Somasundaran, 1983). Under the activation circumstance using the lead ion as the activator and sodium oleate as the collector, the interaction mechanism seems to be still unclear. In the present study, the interaction mechanism between ilmenite and sodium oleate using lead ion as the activator are studied by microflotation, zeta potential measurements and adsorption density calculation. EXPERIMENTAL Materials and reagents Pure ilmenite minerals were obtained from Panzhihua, Sichuan province, China. The minerals were ground in a porcelain mill with an agate ball. Following that, the prosucts were sieved, and the samples of -0.074+0.038 mm size fraction were used for the microflotation experiments. The results of XRF show that the content of titanium element is 30.58%, showing that the purity of ilmenite is above 90%. On the basis of the results of XRF, it is determined that the purity of ilmenite is very high and meets the needs of microflotation"

Jan 1, 2017

If a fire occurs outby an underground coal mine section, the immediate safe evacuation of miners from the working section should always be the first action during the rescue operation. Unfortunately, in many cases, the escape-ways (escape routes) dedicated for miners' evacuation are contaminated with fire byproducts from adjacent entries. The purpose of this paper is to present the ventilation control process that will maintain the escape-way free from contaminants and available for travel. Several scenarios in a different section on ventilation system arrangements are analyzed, discussed and presented. To perform these studies, the author used a mine-fire simulator, which provides a dynamic (in real time) representation of the fire's progress and also gives a display, a color-graphic visualization, of the spread of combustion products throughout the ventilation system. Presented and discussed in this paper, also, are ways in which the mine-fire simulator can be used as a training and teaching tool for miners and, particularly, for ventilation and safety personnel.

Jan 1, 1993

Current scrubber capacities vary from 1.89 to 4.72 m3/s (4,000 to 10,000 cfm), and there is interest in using scrubbers with capacities up to 6.61 m3/s (14,000 cfm). This paper describes research to compare the effectiveness of blowing and exhausting face ventilation systems using high-capacity scrubbers with flows up to 6.61 m3/s. Tests were conducted in a surface ventilation gallery with exhaust and blowing systems operating under similar conditions. The mining machine was equipped with a machine-mounted scrubber. Methane gas was released at constant flow at the mining face and measured at several face locations. Effectiveness of exhausting and blowing systems was compared by determining average face methane concentrations. For each operating condition tested, blowing ventilation was more effective than exhausting for controlling face methane levels. Raising scrubber flow to 6.61 m3/s reduced methane levels for both blowing and exhausting systems.

Jan 1, 1996

By R. E. Vivas, J. A. Villa

"INTRODUCTION Located in the state of Colima, Peña Colorada is one of the largest iron ore operations in Mexico. The project is owned in equal parts by ArcelorMittal and Ternium. Though boasting a production capacity of 4.5 million tons of concentrate per year, Peña Colorada is faced with declining ore grades. In order to respond to this situation, Peña Colorada had to expand production even further. This expansion created various challenges that were overcome by the adoption and application of new technology. Examples of these technological innovations are discussed in detail in this paper and include improvements in geo-modeling, mine planning and mine operations. The successful implementation of these technologies paid for itself many times over, and has led to significant improvements in production and performance, while lowering the operating costs and reducing the variance between planning and execution. PROJECT OVERVIEW Peña Colorada is a mining company which produces about 30% of the iron ore in Mexico. This project generates about 1,200 direct jobs and 3,000 indirect jobs, making a significant contribution to the local economy. Similarly, Peña Colorada invests in its local communities through numerous educational programs, scholarships, university agreements, social development, environmental agreements, etc. Peña Colorada’s operations consist of an open pit mine located in Minatitlán and a pellet plant located in the port city of Manzanillo, as shown in the location map below:TECHNOLOGICAL INNOVATIONS Most mining projects around the world typically follow the logic of “mining the next best ore”. Consequently, head grades tend to decline over the life of the mine. In the case of Peña Colorada, a decline in head grade combined with a decline in iron ore prices forced the operation to adapt to a new business environment and adopt new technologies to face these challenges. However, the first step along this process was to increase the confidence and reliability of the resource model. This task involved additional drillhole campaigns coupled with more detailed modeling techniques. Once the block model was completed, new optimization studies and production schedules were evaluated with new optimization tools that unlocked significant project value in many aspects of the mine plan. Similarly, new geotechnical studies were prepared, which provided new guidelines for pit slope design, and new technology was implemented to monitor ground movement and slope stability. The picture below shows two sectional block model views in MineSight 3D, along with the pit designs and geologic solids"

Jan 1, 2017

By P. J. Best

Due to its low mine production costs, competitive rail rates and low sulfur content, the Southern Powder River Basin (SPRB) now commands 30 percent of the U.S. utility coal market. In 1996, production exceeded 260 million tons, a growth of 110 million tons since 1989 and 15 million tons over 1995. Continued growth is expected as the second phase of the Clean Air Act Amendments (CAAA) looms. This growth will be the greatest in the southern part of the basin, where coal quality is higher. This article is an overview of supply and demand issues affecting markets for SPRB coal. It reviews the current markets for SPRB coal and addresses future prospects for market expansion.

Jan 1, 1998

By Stephen H. E. Phillips, Michael J. Beus

A pneumatic impact breaker is used to fragment the rock at the shaft bottom, replacing the drill and blast cycle. A backhoe-type mucker removes the broken rock. The operators are in protective cabs below the bottom work deck in the shaft. Preliminary testing has been accomplished at underground and surface test sites in Arizona. Seven, approximately 6.4 m deep by 7.3 m-diameter (21 ft by 24 ft) test holes, (a total of 45 m (148 ft)), were recently excavated in various rock types, including jointed and massive quartz monzonite and rhyolite. An average advance rate of .4 m/hr (1.24 ft/hr) has been achieved. This includes breaking and mucking the rock. Further data is being sought from an in-shaft demonstration.

Jan 1, 1981

By N. T. Rogers

An accepted statement of fact is that transportation next to agriculture is the second most important industry in the world. The transportation networks of the United States contributed immensely to the growth and prosperity of our nation. My objective is to make each and everyone here aware of the need for communication between geologists, mining engineers, purchasing agents and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, covered wagons or whatever. If this is your only exposure to the transportation industry then you probably spent most of your life in a cave.

Jan 1, 1989

By B. Anameric, S. K. Kawatra

Pig iron nuggets were produced in a laboratory scale furnace at Michigan Technological University. These nuggets are produced from pellets consisting of a mixture of iron oxide, coal, flux, and a binder, which are heated to 1450°C.These pellets then self-reduce to produce a solid, high-density, highly metallized (96.5% Fe) pig iron. During the nugget production process, a separate slag phase forms that cleanly separates from the metal. The physical and chemical properties of the pig iron nuggets are similar to pig iron produced by blast furnaces, which is distinct from Direct Reduced Iron (DRI).

Jan 1, 2004