Search Documents

By Robinson Leon-Diaz, Alberto Jaen-Toribio, Raymond Blanchard, Mike Deevy, Miguel Fuentes-Llanos

"Tunnels designed to NFPA 502 are required to withstand the RWS time-temperature curve, more specifically prevent progressive spalling and loss of strength of steel reinforcement. Fire boards or spray-on layers can be effective, however, these solutions have capital and whole-life cost implications. The use of “fire resistant” concrete based on a suitable aggregate with polypropylene fibers has also increased in recent years. This article presents a new methodology for thermal and structural analysis of segmentally lined tunnels, which permits the analysis of project specific fire curves and an assessment of different fire protection strategies. The effectiveness of fire boards is assessed along with whether “fire resistant” concrete alone is a viable means of achieving the required protection. Finally, since NFPA 502 recommends water-based fixed fire-fighting systems for Category C and D tunnels, we discuss the question of how a fixed fire-fighting system should be addressed within the structural design. INTRODUCTION Protecting road tunnels from structural damage and collapse is a key requirement for both life safety and business continuity. Where road tunnels are part of key highway corridors, protecting business continuity is a high priority for owners, operators and the Authority Having Jurisdiction. For existing tunnels, compliance with NFPA 502 may require upgrades with either passive fire protection and/or water-based fixed firefighting systems. For new tunnels, compliance with NFPA 502 requires a combination of good practice in design and fire testing. A water-based fixed firefighting system is a Conditionally Mandatory Requirement1 for Class C and D tunnels, i.e. all tunnels greater than 300m and 1000m long respectively. The basis for fire safety design of new tunnels and assessment of existing tunnels is the worst-case fire scenario. A number of factors, including but not limited to the following, influence this design fire scenario:"

Jan 1, 2016

By W. J. Mahoney

A good quality assurance program at a coal mine or power plant is accurate, timely, and consistent. The quality analysis is accurate due to a complete sampling of the coal stream loaded into the unit train. The sample analysis is accurate because standardized testing procedures are applied. Once the analysis is completed, the results must be communicated to the electric utility in a timely manner. The electric utility needs the results to better manage the coal inventory at the power plants. A quality assurance program can also help the mine deliver a consistent product to the electric utility's power plants. The importance of the three major tenants for a good quality assurance program: accuracy, timeliness and consistency, are based on major changes that are taking place in the electric utility industry.

Jan 1, 1994

By Linda Frederick

In July 1997, Krupp Canada obtained the contract to design and supply the conveyor system for Chile's Los Pelambres copper mine expansion project. Progress on the overland conveyor system is currently on schedule. It is a challenging task to convey copper ore from an open-pit mine located on a mountain site 3,000 m (9,840 ft) above sea level down 1,300 m (4,265 ft) to the processing plant at the valley floor below. The Los Pelambres conveyor system moves copper ore at a rate of 8.7 ktlh (9,600 stph) and at a speed of 6 ml sec (1,180 ftlmin) for 12,750 m (41,830 ft). The distance is divided in three conveyors, each 1,800 mm (71 in.) wide. The largest conveyor is 6 km (3.7 miles) long. To protect against avalanches and rockslides, the conveyors run through a 12-km- (7.4-mile-) long tunnel system. The lowest of the three conveyors is equipped with a shuttling head end. With this, the conveyor discharge point can be moved back and forth by 100 m (330 ft), allowing it to build up a longitudinal stockpile at its end. To meet the extreme design parameters, the limits of conveyor design had to be pushed to record-setting marks. For instance, the ST-7800 steel cord conveyor belt is the strongest belt ever installed in a conveyor system. A total drive power of 25 MW (33,535 hp), consisting of 10 2.5-MW (3,352-hp) drives, is included in the design plans. In loaded condition, the electric motors act as generators and feed electric energy back into the power grid. The motors are controlled by variable frequency inverters that provide an infinite adjustment of motor speed. This technology allows starting and stop- ping the conveyors precisely along predetermined acceleration and deceleration ramps. This is done so harmful belt jerking and stress waves can be avoided.

Jan 1, 1999

By J. M. Smith, T. R. Horton, R. L. Blanchard, T. W. Fowler

INTRODUCTION Uranium mining operations release radioactive materials into both air and water and generate large quantities of solid wastes containing low levels of radioactive materials. Solid wastes produced by mining operations remain on the surface at many inactive mining sites in the Western United States. These mining effluents may present a potential health and environmental hazard. Therefore, Congress, in Section 114(c) of the Uranium Mill Tailings Radiation Control Act of 1978, instructed the Administrator of EPA to prepare a report identifying the location and potential health, safety, and environmental hazards of uranium mine wastes and to recommend a program to eliminate these hazards. Several facts and limitations helped shape the method and approach of the EPA study. Little information on uranium mines was available; measurement information that was available on uranium mine wastes was frequently influenced (biased) by nearby uranium mills; time and resources did not permit comprehensive field studies to provide additional data; and there are inherent variations between uranium mines and sites that complicate generic assessments of mine wastes. To accommodate these facts, the EPA developed conceptual models of uranium mines and made health and environmental projections from them. The models were based upon available data from the literature, supplemented with information from discussions with persons inside and outside the EPA, and by doing several short-term field studies in Texas, New Mexico, and Wyoming. When necessary, conservative (maximizing) assumptions were employed. This paper presents a brief account of a part of the EPA study dealing with the potential health and environmental effects caused by active surface and underground uranium mines. Airborne contaminants are emphasized, although solid and liquid effluents are also included. Due to the limited space, only the methods and parameters used and the results of the assessments will be presented here. Anyone interested in the source of the data used and the development of the parameters should refer to the EPA report (Blanchard et al., 1981). The occurrence and emissions of stable elements were included in the EPA report, however, due to space limitations and their apparent small impact, except for possibly at some specific mines, only radioactive sources will be included in this presentation. MODEL URANIUM MINES The model surface mine was located in the South Powder River Basin of Wyoming and the model underground mine was located in the Ambrosia Lake area of New Mexico. These are the prevalent type mines in those areas. The model mines were based on the average production parameters of the 63 open pit mines and the 256 underground mines that were operating in the United States in 1978 (Department of Energy, 1979) and on a report of an extensive study of open pit mines in Wyoming (Nielson et al., 1979). Information contained in environmental impact statements and in reports from federal and state agencies was also used. Parameters for the model mines are listed in Table 1. The surface mining scenario is that 7 pits are opened in the 17-year mine life with overburden from each successively mined pit used to backfill a previously completed pit, resulting in an equivalent of one pit of overburden (2.4 year production) stored on the surface. No backfilling is assumed at the underground mine. Overburden or waste rock, ore, and sub-ore are separated into separate piles that are either rectangular in shape with length twice the width or in the shape of a frustum of a regular cone. Both shapes have 45 degree sloping sides. To account for bulking, the volume of the material comprising the piles was considered to be 25% greater than the volume of material removed from the ground. It was assumed that dewatering was required at both mine sites. Wastewater discharge rates at the surface and underground mines were assumed to be 3.0 and 2.0 cu m per min, respectively. SOURCE TERMS The following radioactive contaminants at active uranium mines were assessed in the EPA report: 1. Radioactive particulates in a) wind suspended dust from waste rock (overburden) pile, sub-ore pile, ore stockpile, b) suspended dust from mining activities (rock breakage, loading and unloading ore and wastes), and c) vehicular dust, 2. Rn-222 emanation from waste rock (overburden) pile, sub-ore pile, ore stockpile, and mining activities, 3. Rn-222 emanation from mine surface areas, and 4. Radionuclides in wastewater discharged to land surface. Estimated average annual dust emissions (item 1 above) from the model mines are listed in Table 2. Emission factors and the assumptions used to estimate these dust emissions are described in detail in the EPA report. Radioactive source terms were computed for each of the sources; dust emissions were multiplied by the concentrations listed in Table 1

Jan 1, 1981

By G. C. Kachel

Significant effort has been expended and considerable success has been realized m the application of instrumentation and automatic control equipment in the mining and ore processing industries. This effort has been applied principally to process equipment with the objective of increasing throughput, minimizing labor requirements and/or improving grade or product quality. Less spectacular, but quite rewarding has been the successful application of instrumentation and automatic control equipment to a wide variety of material handling equipments. This paper describes some of this work including: (1) automatic weighment of load-haul-dump units and trams underground; (2) automation of skip loading; (3) instrumentation applied in feeders and conveyors; (4) level measurement in bins, silos, vessels and sumps; (5) automatic blending of sized materials; (6) automatic loading of ships, trains and trucks; (7) automatic control of tailings disposal facilities

Jan 1, 1973

By B. Nyman

A lot of work is in progress to improve copper recovery by leaching-solvent extraction-electrowinning (L-SX-EW). At Outokumpu the focus of attention is on SX equipment development as a result of which a new mixing-settling technology, the Vertical Smooth Flow (VSF) has been introduced. Using helical stirrers in the VSF mixers a more gentle and uniform contacting can be obtained than in the mixing compartments of the low-profile design. The benefits of Outokumpu's new approach are an essential decrease in organic losses and in aqueous in organic entrainments. Separate pumping using a smoothly pre-contacting "Dispersion Overflow Pump" (DOP) is a key feature of the VSF design. The scale-up of this pump as well as the VSF mixers are shown to follow simple mathematical relationships which also have been confirmed by full scale experiments.

Jan 1, 1995

By J. A. Wallace

U. S. Steel's coal mining research activities are directed toward providing new or improved hardware and techniques to increase productivity or reduce cost. Because more than 80 percent of U. S. Steel's coal production is obtained from continuous miner sections, most of our research efforts are focused upon that mining system. Current and historical time study data show that our continuous miners only operate about 30 percent of the available face time. This limited equipment utilization is the result of the delays or interferences imposed by the non-coal-cutting phases of the continuous mining cycle. The most time consuming of these delays are: waiting-on-roof-support, tramming between alternate work locations, waiting-on-haulage-capacity, and in some mines waiting for excessive methane concentrations to clear. Because waiting on roof support is our most time consuming delay, several programs are underway simultaneously to address this problem. In one of these we are developing a patented microprocessor-based control method and apparatus to improve roof drilling performance. This increase is attained by using the microprocessor to adjust electrohydraulic valves which control drill thrust and rotation speed. The microprocessor is designed to continuously search for an optimum combination of thrust and drill rpm to maximize penetration rate at all times.

Jan 1, 1979

By Frank C. Schora

The Institute of Gas Technology for many years has dedicated a large portion of its research effort to the development of a practical solid-fuel-based gasification process to produce a synthetic natural gas equivalent. The work is being done to prepare for the day when supplemental gas will be needed. This program, initially supported by the American Gas Association, and now by both the Department of Interior's Office of Coal Research and the American Gas Association, has developed the IGT Hydrogasification Process. This process, now entering the pilot plant stage, is based on the high-temperature, high- pressure hydrogenation of coal with a hydrogen-steam bearing gas. Product gas from this step is cleaned and catalytically methanated to produce a high-Btu gas. Estimated production costs indicate the process will be competitive with natural gas in certain areas of the country when required.

Jan 1, 1969

By George S. Austin

Adobe, dried mud bricks, have been used since before historic time in the construction of dwellings. Building materials are normally evaluated for thermal performance based on measurements known as R- and U-values. The R-value is an indicator of the ability of a wall to insulate effectively and the higher the R-value, the better it is as an insulating material. The U-value, or value of conductance, is the reciprocal of the R-value and reflects the rate at which heat is conducted through a material. But the "heat capacity of the wall" must also be considered. This measures the length of time that passes before a steady state of heat flow is achieved. The effective U-value measures both the resistance to the transfer of heat and the capacity to hold heat. These latter value make adobe a far more interesting as a modern building material that was formerly recognized.

Jan 1, 1983

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By H. R. Manouchehri

The responses of calcite, feldspar, and quartz minerals In a laboratory free fall electrostatic separator, before and after tribocharging with stainless steel, PVC, and copper plates, have been investigated. The effect of H3BO3 and BaCl2 chemicals pre-treatment on the electrical properties of the minerals is examined. The changes in the electrical properties are discussed with the determined charge, dielectric constant, and electrical conductivity of the mineral samples. Electrical properties of the minerals and their responses to the electrical field during separation, after tribocharging and chemical pre-treatment, are explored for the need to characterize the electrical behaviour of the minerals.

Jan 1, 1998

By D. W. Park

Underground room-and-pillar mining operations in the Warrior Coal Field in Alabama frequently suffer instability due to soft floor and thinly-laminated immediate roof. The investigation covered by this paper concerns a mine that was experiencing ground-control problems with weak floor conditions. Four hundred ft above the presently producing seam, another seam has been mined out. Several roof falls occurred locally, and as much as two ft of floor heaves have been experienced. The paper presents the results of comprehensive analysis conducted on floor heave, roof sagging, and the influence of the mined-out seam using instrumentation and numerical analysis.

Jan 1, 1991

By Etienne Simode

When a fire breaks out in a mine access road, the hot smoke, due to heat transfer with the surrounding strata, progressively cools as it moves forward. Depending upon the resulting temperature distribution, the density of the fluid changes. This change will bring about: Firstly, a variation in the resistance of the roads, a static factor which will affect ventilation flow rates; Secondly, the appearance of extensive aerodynamic driving loads in the vertical and angled roads, a dynamic factor which can have an extensive impact on ventilation. Because of the appearance of combustion and distillation products, the vaporization of water, which wets the timbering and strata, and the expansion of gases, fluid rates can at times be increased tenfold in the area of the fire. These disturbances may cause explosions and ventilation inversions, which fill other working areas with smoke toxic to workers, and which can come up upon rescue teams from behind. Due to the progressive heating of the surrounding rocks, which will slow down heat transfer, these dangerous conditions change over time. At the Lorraine Basin Coal Mines, programs have been set up and employed for the computer simulation of these phenomena over time. They serve to anticipate or to understand such phenomena, the input data being the characteristic parameters of the mine ventilation network, the operating curve of the main fans, and measurements or estimates of some temperatures. Two programs, employed together, have been developed for these studies: One program, called RESO, calculates the distribution of flow rates and pressures throughout the entire network; The other, called FEUMIN, determines smoke temperatures over their entire path.

Jan 1, 1980

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the key parameters influencing the gold recovery. The model was used to direct modifications to plant operating practice. The cyanide dosing strategy was changed to reduce preg-rob gold losses and cut reagent consumption A finer grind was achieved without capital investment. The density in CIL was lowered, and tighter control was exercised over plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz, and concomitant reagent cost savings of $55,000/month.

Jan 1, 1999

By I. O. Otunniyi

The natural hydrophobic response flotation method for beneficiation of printed circuit board comminution fines (PCB CF) still requires many studies to further basic understanding of the process and the flotation traits that the PCB CF presents. Varying particle size distribution (PSD) and water recovery under the scheme show that higher mass pull, obtained at the finer PSD, gave lower water recovery but higher value loss. The reverse also holds: the least mass pull at the coarsest PSD used, -106 + 75 µm, gave the highest water recovery per unit mass pull with the highest reverse recovery. This is unlike what obtains in primary resources processing, where higher water recovery is often with increased fines entrainment. The reverse recovery loss here is, therefore, more due to entrapment with the heavy mass pull characteristic of the method than to the entrainment of value with water. Other peculiarities of the system observed are discussed, with the goal of improving the performance of the process, and broadening the general knowledge of flotation systems.

By Ingo Ossenbühl, Wolfgang Dolsak, Vojtech Gall, Axel G. Nitschke

"Yielding support systems for application in underground construction have a long history, primarily in mining. Typical examples are tunnels subject to loading conditions that lead to overstressing of the newly installed support or existing tunnel structures in active fault zones. Recent applications for tunnel rehabilitation projects unveiled the capabilities and flexibility of combined yielding support systems presented in this paper. Frequently, the main requirements for tunnel rehabilitation applications are a fast, safe, and simple installation along with the need for flexibility with regards to existing tunnel geometries. A combined support system consisting of steel sets with yielding connections and special groutable hoses has proven to be an efficient support measure providing a multitude of advantages compared to conventional rehabilitation approaches. The presented yielding support system provides an immediate and active support, while it allows for controlled yielding upon experiencing loads beyond its support capacity. INTRODUCTION The excavation of underground spaces leads to redistribution in the existing stress regime. This load redistribution goes along with deformations in the surrounding rock mass. Magnitude and duration of these deformations depend on the tunnel’s depth and geological conditions, but also on the installed support system. Modern civil tunneling infrastructure has generally an envisioned service life of about 120 years. Conventional tunneling provides typically a dual support system, split into the initial (or primary) and final (or secondary) lining. A typical design principle in civil tunneling is to let the vast majority of deformations acting on the initial lining cease, before the final lining is installed. Based on this approach, the loading on the final lining is significantly reduced and signs of overstressing, such as cracking of the lining, are typically limited to the initial lining. However, special cases in swelling and squeezing ground require different approaches, including yielding support systems."

Jan 1, 2016

By G. Norman Owen, Roger E. Scholl, Tor L. Brekke

INTRODUCTION Underground structures are generally regarded to be safer than surface structures during strong seismic motion, except when crossing a causative fault. Recent studies of observed earthquake damage to tunnels generally support this view, although instances of severe damage and, occasionally, collapse are reported. For proposed underground construction of sensitive structures such as nuclear power plants, liquefied natural gas facilities, and nuclear waste repositories, a verification of the seismic response of underground structures will be required.. This paper discusses the stabilization recommendations used in a study of additional costs required to protect tunnels against ground motion caused by earthquakes and underground nuclear explosions (1). The study is a part of the site investigations for possible construction of a nuclear waste repository. The additional costs estimated in the study are not presented here; only the stabilization measures are presented in the present paper. The tunnels, which would constitute the underground facilities of a possible repository, are assumed to be 5.5 m (18 ft) in diameter and to be located at a depth of 600 m (2,000 ft). Three candidate geological materials are considered: argillite (shale), granite, and tuff. Several peak ground accelerations are used: 0.3g, 0.5g, and 0.7g for earthquakes, and 0.5g, 0.7g, and 1.0g for underground nuclear explosions. Potential damage due only to shaking is considered here. This paper does not discuss problems that result from creep or sudden rupture of intersected faults or from ground failures at portals.

Jan 1, 1979

By Dianne M. Satalic, Peter A. Spencer

Bacterial leaching is a mature technology and has been applied in six commercial plants with others in the design stage or under construction. Bacterial oxidation is a relatively inexpensive process which uses naturally occurring soil bacteria to assist in extraction of base and precious metals. Bacterial oxidation has ini­tially been applied for gold recovery but the technology is now being transferred to base metal leaching with processes already developed for copper, cobalt and nickel. Bacterial oxidation plants often have capital and operating cost advantages over competing technologies and do not need a highly skilled workforce. The most common species found in the conditions used for bacterial oxidation and bacterial leaching are Thiobacillus fer­rooxidans and Thiobacillus thiooxidans. One common species other than Thiobaci!lus found in the commercial bacterial leach cultures is Leptospirillum ferrooxidans. Mixed cultures of the three species named here have formed the basis of the technolo­gy applied in most of the commercial applications of bacterial leaching to date. These bacterial species already mentioned all belong in the classification of mesophiles and have an operating range from 20 to 43°C. One other culture, a moderate thermophile operating over the range 40 to 50°C, has been used in one commercial plant in Western Australia. Bacterial oxidation takes place in acidic solutions under aer­obic conditions. The oxidation reaction normally produces iron (II) in solution which is ultimately conve1ted into the iron (III) form. The pH value falls naturally as the sulphide minerals are oxidised and the starting pH value can fall as low as pH 0.6 as the oxidation reaction proceeds. This paper examines the impact of the technology selection and its application on the design, engineering and operation of a bacterial oxidation plant. The effect of the changes to these para­meters on the cost of the bacterial oxidation plant is discussed.

Jan 1, 1998

By Sue Sawyer

In October, November and December, teachers at the National Science Teachers' Association (NSTA) area conventions were lured to visit the Minerals Education Coalition (MEC) booth by the promise of free rocks, video tapes, and literature on earth science topics. Teachers were content to stand in lines that at times took as much as an hour and a half to progress through the exhibit. Adding to their interest was the opportunity to converse with people from the minerals industry who were staffing the booth. The MEC was formed by a group of associations and companies in the minerals industry. They felt the need to educate the public about the current-day minerals industry and how it affects everyone's life. The American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. (AIME) underwrote the major expenses of exhibit space and exhibitor services at all three conventions in 1997. SME members have been active in staffing and chairing the NSTA exhibit booth. But they represented only about one-third of the volunteers for the booth. Additional volunteers were drawn from local minerals companies, associations, interested teachers and other support groups. (See donors list on page 64.) In 1997, the conventions were held in Pittsburgh, PA, Denver, CO and Nashville, TN. The local SME GEM Committees chaired Pittsburgh and Denver and The Rogers Group Inc. supplied the chairperson in Nashville. Each exhibit relies on a local committee to plan and run the booth. Support is available from the GEM Projects Coordinator at SME headquarters. Usually the chair of the committee is drawn from the local SME membership. It is easy to see why the MEC booth is so popular. Free literature, videos, posters, workshop packets and rock specimens were handed out to about 5,500 science teachers at the three sites. Feedback from the attending teachers was overwhelmingly positive: "Who do we thank for these great materials?" Some of those great materials included Caterpillar's outstanding donation of Common Ground videos and teacher packets for Pittsburgh, Denver and Nashville for every teacher expected to attend. Placer Dome sent enough What's a Mine coloring books and It Comes from a Mine activity books for teachers at all three sites. Newmont supplied all teachers with an excellent poster describing gold processing. Women in Mining Education Foundation had plenty of its classroom activity handouts. The American Coal Foundation provided a list of its educational materials that are given out free to teachers who request them on school letterhead. The National Mining Association had its Facts About Minerals and Facts About Coal available. US Borax provided the funding to reproduce the NMA black and white posters that were published as inserts in Mining Voice magazine. In addition, each site had other materials chosen by the local committees to round out their selections. At each exhibit site, committees raise between $8,000 and $12,000 in cash donations from industry to support the high overhead of producing this exhibit. Usually, there are between 12 and 18 different rock specimens representing a range of mineral ores from aggregates to the metal ores. The committee arranged to have these donated (along with the freight charges to ship them to the site). Literature is also donated by the industry. It covers a diverse spectrum from basic information on rocks and minerals to posters, flow charts, videos and coloring books. Other donations include storage space before the event, haulage of items to the hall and door prizes. These exhibits could not have been staged without the network of SME Local Sections and the able chairs and committees at each site. At this time, credit should be given to their extensive donation of time and effort.

Jan 1, 1998

By A. B. Van Cleave

It was first pointed out in 1934 by Gaudin (1) that the "oily" oxidation product of the alkyl xanthate ion-dialkyl dixanthogen, might be the "active flotation agent" on sulphide minerals and there have been a number of studies supporting this hypothesis (2,3,4). However, all of these studies have relied largely on electrochemical evidence. Galena, being a semiconductor, may be used as an electrode in aqueous solution and it was shown that ethyl xanthate ion does not adsorb with charge transfer in the absence of oxygen unless the potential of the galena surface is above -100 mv versus the hydrogen electrode (H2 E). At this potential the galena surface is slightly hydrophobic but does not become strongly hydrophobic unless the potential is raised to 210 mv (versus H2 E). It is suggested that, at potentials of 210 mv or above, ethyl xanthate ions are oxidised to diethyl dixanthogen and that chemisorption of oxygen raises the galena surface to this potential. On the other hand, examination of xanthated galena surfaces by chemical or physical methods (5,6,7) has failed to detect dixanthogen and it has been shown that dixanthogen may be reduced to lead xanthate at a lead sulphide surface. (5,8)*. It was suggested by Leja and Poling (5) that, as dixanthogen is a neutral molecule it would not be repelled by the negatively charged galena surface so that the adsorption was envisaged as taking place through homogeneous oxidation of the xanthate ion to dixanthogen, adsorption and reduction of the dixanthogen to a chemisorbed lead xanthate species. In paper I of this series (11) it was shown that the thiosulphate ion, which forms on galena surfaces in slurries at the pH normally used for flotation, will reduce dixanthogen. There is, therefore, the impasse that the electrochemical evidence requires that xanthate ion be oxidised to dixanthogen at the galena surface while the chemical evidence shows that the reverse reaction takes place.

Jan 1, 1973